Electrical and optical properties of a novel nonconjugated conductive polymer,poly(β‐pinene)

Electrical conductivity in a novel nonconjugated conductive polymer, poly(β‐pinene), has been measured as a function of molar concentration of iodine. The conductivity increases about 10 orders of magnitude to a maximum value ?8 × 10^?3 S/cm. The molar concentration of iodine, corresponding to saturation, is ?0.85. The optical absorption measurements after light doping have shown two peaks: one at 4.0 eV and the other at 3.1 eV. The first peak is due to the radical cation, and the second due to the charge‐transfer between the double bond and the dopant. As observed in other nonconjugated conductive polymers, the second peak becomes broader and undergoes a red shift, upon higher doping. The FTIR spectroscopic studies have shown that the C?C stretching vibration at 1610 cm^?1 and the ?C? H bending vibration band at 728 cm^?1 decrease upon doping, because of decrease of double bonds. Photoluminescence studies of poly(β‐pinene) show a maximum value at 360 nm for excitation at 280 nm. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3695–3698, 2005     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Highly luminescent diyne (?CC?CC?) containing hybrid polyphenyleneethynylene/poly(p‐phenylenevinylene) polymer: Synthesis and characterization

Luminophoric dialdehyde 1,4‐bis[4‐formylphenylethynyl‐(2,5‐dioctadecyloxyphenyl)‐buta‐1,3‐diyne] ( 4 ) enables the synthesis of diyne‐containing hybrid polyphenyleneethynylene/poly(p‐phenylenevinylene) polymer poly[1,4‐phenylene‐ethynylene‐1,4‐(2,5‐dioctadecyloxy)phenylene‐butadi‐1,3‐ynylene‐1,4‐(2,5‐dioctadecyloxy)phenylene‐ethynylene‐1,4‐phenylene‐ethene‐1,2‐diyl‐1,4‐(2,5‐dioctadecyloxy)phenylene‐ethene‐1,2‐diyl] ( 7 ) with a well‐defined general structure (? Ph? C?C? Ar? C?C? C?C? Ar? C?C? Ph? CH?CH? Ar? CH?CH? )_n, which was confirmed by NMR and infrared spectroscopy. The highly luminescent material is thermostable, soluble in usual organic solvents through the grafting of octadecyloxy side groups, and can be processed into transparent films. With the aim to investigate the effect of ? C?C? C?C? in the photophysical behavior of 7 , a comparison of the photophysics of monomers 3 [1,4‐bis(4‐formylphenylethynyl)‐2,5‐dioctadecyloxybenzene] and 4 and subsequently of their respective polymers 6 and 7 has been carried out. Similar photophysical behaviors for 6 (poly[1,4‐phenylenethynylene‐1,4‐(2,5‐dioctadecyloxyphenylene)ethene‐1,2‐diyl]) and 7 were observed in dilute CHCl₃ solution as a result of an identical chromophore system responsible for the absorption (λ_a = 448 nm) and emission (λ_f = 490 nm) in both compounds. The increased planarization and enhanced rigidity of the conjugated backbone in the solid state at room temperature as well as in frozen dilute tetrahydrofuran solution at 77 K cause the bathochromic shift of the absorption and emission spectra. The large octadecyloxy side chains obviously limit strong π‐π interchain interactions in the solid films, which explains the high fluorescence quantum yields of 35 and 52% obtained for 6 and 7 , respectively. The energetically arduous migration of the π electron through the diyne units not only requires a higher threshold voltage for the detection of photoconductivity in 7 but could possibly limit radiationless deactivation channels of the exciton, which explains the approximate 20% fluorescence quantum yields difference between 6 and 7 in the solid state. The electron‐withdrawing effect of the triple bonds confer both 6 and 7 with a good electron‐accepting property (E^ox = 1.39 V vs Ag/AgCl) if used in light‐emitting diode devices. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2670–2679, 2002     

Effect of ammonium groups on the properties and alkaline stability of poly(arylene ether)‐based anion exchange membranes

Five kinds of ammonium groups functionalized partially fluorinated poly(arylene ether) block copolymer membranes were prepared for investigating the structure–property relationship as anion exchange membranes (AEMs). Consequently, the pyridine (PYR)‐modified membrane showed the highest alkaline and hydrazine stability in terms of the conductivity, water uptake, and dry weight. The chloromethylated precursor block copolymers were reacted with amines, such as trimethylamine, N‐butyldimethylamine, 1‐methylimidazole, 1,2‐dimethylimidazole, and PYR to provide the target quaternized poly(arylene ether)s. The structures of the polymers, as well as model compounds and oligomers were well characterized by ¹H NMR spectra. The obtained AEMs were subjected to water uptake and hydroxide ion conductivity measurements and stabilities in aqueous alkaline and hydrazine media. The pyridinium‐functionalized quaternized polymers membrane showed the highest alkaline and hydrazine stability with minor losses in the conductivity, water uptake, and dry weight. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 383–389     

Radical‐induced oxidation of RAFT agents—A kinetic study

Radical‐induced oxidation of reversible addition‐fragmentation chain transfer (RAFT) agents is investigated with respect to the effect of molecular structure on oxidation rate. The radicals are generated by homolysis of either azobisisobutyronitrile or alkoxyamine and transformed in situ immediately into peroxy radicals through transfer to molecular oxygen. It is found that the oxidation rate depends on the structure of Z‐ and R‐group of thiocarbonylthio compounds. For dithioesters with identical Z‐phenyl substituent, the oxidation rate decreases in the order of cyanoisopropyl (? C(Me)₂CN) > cumyl (? C(Me)₂Ph) > phenylethyl (? CH(Me)Ph) > 2‐methoxy‐1‐methyl‐2‐oxoethyl (? CH(Me) ? C(?O)OCH₃) > benzyl (? CH₂Ph). For dithioesters with identical R‐group, the oxidation rate decreases in the order of Z = phenyl? ～ benzyl? > RS? (trithiocarbonates) > RO? (xanthates). The stability of the RAFT agents toward oxidation correlates well with the chain transfer abilities as those previously reported by Rizzardo and coworkers. The priority of the oxidation reaction over the RAFT process, and the subsequent influence on RAFT polymerization are also investigated. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Poly(arylene ether)s with pendant diphenyl phosphoryl groups: Synthesis,characterization, and thermal properties

A series of poly(arylene ether)s, (PAEs), carrying a pendant diphenyl phosphoryl group were prepared via the nucleophilic aromatic substitution (NAS) reactions of 3,5‐difluorotriphenylphosphine oxide, 6 . The difluoro monomer 6 was synthesized via two‐step reaction sequence and subsequently characterized by ¹H, ¹³C, ¹⁹F, and ³¹P NMR spectroscopy, GC/MS, and elemental analysis. The reactivity of the electrophilic sites in 6 , activated by only a diphenylphosphoryl group located in the meta‐position, in 6 was probed via NMR spectroscopy and model reactions and was determined to be sufficient to undergo typical NAS reactions. High molecular weight, amorphous, organic soluble poly(arylene ether)s, bearing a pendant diphenylphosphoryl group, were prepared via the reaction of 6 with a variety of bis‐phenols under typical NAS conditions. The poly(arylene ether)s were characterized for structure via the use of ¹H, ¹³C, and ³¹P NMR spectroscopy while their thermal properties were evaluated using DSC and TGA analysis. The glass transition temperatures (T_g) of the synthesized PAEs ranged from 143 to 175 °C, while their 5% weight loss temperatures ranged from 467 to 510 °C under nitrogen and from 470 to 526 °C in air. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of epoxidized polybutadiene/polyaniline graft conducting copolymer

In this article the synthesis and characterization of an elastomeric conducting material, obtained by grafting polyaniline (EB) on commercial cis‐1,4‐polybutadiene (PB), are described. PB was first partially epoxidized in chloroform solution using meta‐chloroperbenzoic acid (MCPBA). The conducting polymer was then grafted to the activated polybutadiene (EPB) via the aminolysis reaction between the polyaniline NH₂ terminal groups and the oxirane rings. The material so obtained (EPBPAN) and the epoxidized intermediate product were characterized by ¹H NMR, ¹³C NMR, Fourier transform infrared, and ultraviolet–visible spectroscopy, thermal and mechanical analysis, and electrical conductivity measurements. The effect of the sample deformation on conductivity also was analyzed. The HCl doping of the EPBPAN film induced crosslinking reactions, generated by the acid cleavage of unreacted oxirane groups. The electrical conductivity of the doped material reached values of about 10^?5 Ω^?1 cm^?1. The key characteristics of our elastomeric conducting material are its simple synthesis, its starting as a commercial product, and the solubility of its undoped form in a common low‐boiling organic solvent like chloroform. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3082–3090, 2004     

Enhanced electrochemical properties of a novel polyvinyl formal membrane supporting gel polymer electrolyte by Al2O3 modification

Polyvinyl formal (PVFM)‐based dense polymer membranes with nano‐Al₂O₃ doping are prepared via phase inversion method. The membranes and also their performances as gel polymer electrolytes (GPEs) for lithium ion battery are studied by field emission scanning electron microscope, X‐ray diffraction, differential scanning calorimetry, mechanical strength test, electrolyte uptake test, electrochemical impedance spectroscopy, cyclic voltammetry, and charge–discharge test. The polymer membrane with 3 wt % nano‐Al₂O₃ doping shows the improved mechanical strength of 12.16 MPa and electrolyte uptake of 431.25% compared with 10.47 MPa and 310.59% of the undoped sample, respectively. The membrane absorbs and swells liquid electrolyte to form stable GPE with ionic conductivity of 4.92 × 10^?4 S cm^?1 at room temperature, which is higher than 1.77 × 10^?4 S cm^?1 of GPE from the undoped membrane. Moreover, the Al₂O₃‐modified membrane supporting GPE exhibits wide electrochemical stability window of 1.2–4.8 V (vs. Li/Li⁺) and good compatibility with LiFePO₄ electrode, which implies Al₂O₃‐modified PVFM‐based GPE to be a promising candidate for lithium ion batteries. © 2014 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 572–577     

Stilbene‐containing polyactylenes: Molecular design,synthesis, and relationship between molecular structure and NLO properties

Polyacetylenes ( P1–P4 ) containing different stilbene groups, ? [(CH?C) ? Ph? CH?CH? Ph? R]_n? (R?OC_mH_2m+1 (m = 4 ( P1 ), 10 ( P2 ), 16 ( P3 )), or NO₂ ( P4 )) were designed and synthesized, respectively, using [Rh(nbd)Cl]₂ as a catalyst. Their structures and properties were characterized and evaluated by FTIR, ¹H‐NMR, ¹³C‐NMR, GPC, and UV, PL, respectively. The optical limiting and nonlinear optical properties were investigated by using a frequency doubled, Q‐switched, mode‐locked Continuum ns/ps Nd:YAG laser system and their optical limiting mechanism was discussed. It is surprising to see that the stilbene pendants endow the polyacetylenes with a high thermal stability (T_d ≥ 270 °C), novel optical limiting properties and large third‐order nonlinear optical susceptibilities (up to 4.61 × 10^?10 esu). The optical limiting mechanism is mainly originated from reverse saturable absorption of molecules. In addition, it is found that the polymer with electron accepted NO₂ moiety exhibits better optical properties than that with electron donated alkoxy group because of larger π electron delocalization and dipolar effect. The strong interaction between stilbene pendants and the polyene main chain significantly results in red‐shift of fluorescence emitting peak. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4529–4541, 2008     

Synthesis and Characterization of Phenolphthalein‐Containing Sulfonated Poly(arylene ether phosphine oxide)s by Direct Polycondensation for Proton Exchange Membrane

A series of novel phenolphthalein‐containing sulfonated poly(arylene ether phosphine oxide)s (sPAEPP) with various sulfonation degrees were synthesized by direct polycondensation. The structure of sPAEPP was confirmed by ¹H‐NMR, ¹³C‐NMR, and IR spectroscopy. The high‐molecular weight of these polymers was determined by gel permeation chromatography (GPC). The transparent, tough, and flexible membranes could be achieved by solution casting. The macroscopic properties and microstructure of the obtained membranes were investigated in detail. The results showed that these sPAEPP membranes displayed excellent properties in terms of swelling, proton conductivity, and methanol permeability. For example, sPAEPP‐100 membrane exhibited an appropriate water uptake of 33.1%, a swelling ratio of only 11.7% (lower than 20.1% of Nafion 117), a proton conductivity of 0.11 S cm^?1 (similar to that of Nafion 117) at 80 °C, and a methanol permeability of 4.82 × 10^?7 cm² s^?1. Meanwhile, it also presented outstanding oxidative stability. Atomic force microscope (AFM) micrographs showed that the hydrophilic domains of the sPAEPP‐100 membrane formed connected and narrow ionic channels, which contributed to its high proton conductivity and good dimensional stability. As a result, sPAEPP‐100 membrane displays excellent application prospect for fuel cells. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1097–1104     

Proton‐conducting polymers based on benzimidazoles and sulfonated benzimidazoles

A sulfonated derivative of polybenzimidazole is reported, and its properties are analyzed in comparison with related polybenzimidazole proton‐conducting materials. Poly(2,5‐benzimidazole), poly(m‐phenylenebenzobisimidazole), and poly[m‐(5‐sulfo)‐phenylenebenzobisimidazole] were prepared by condensation of the corresponding monomers in polyphosphoric acid. Several adducts of these polymers with phosphoric acid were prepared. The resulting materials were characterized by chemical analysis, Fourier transform infrared spectroscopy, and thermogravimetric analysis; also, the dc conductivity of doped and undoped derivatives was measured. Similar to what has been observed for the commercial polybenzimidazole polymer (also examined here for comparison), the title polymers exhibit high thermal stability. Furthermore, their doping with phosphoric acid leads to a significant increase in conductivity from less than 10^?11 Scm^?1 for the undoped polymers to 10^?4 Scm^?1 (both at room temperature) for their acid‐loaded derivatives. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3703–3710, 2002     

Partially fluorinated sulfonated poly(arylene sulfone)s blended with polybenzimidazole

A partially fluorinated and sulfonated poly(arylene sulfone) (SPSO) was successfully synthesized via nucleophilic polycondensation of 2,2‐bis(4‐fluorophenyl)hexafluoro‐propane with 4,4′‐thiobisbenzenethiol (TBBT). In a second step, the prepared poly(arylene sulfide) was oxidized to SPSO. The polymer was blended with the polybenzimidazole PBIOO^® to obtain a mechanically stable membrane. This film was compared with other polymer blends, which were synthesized in our group in the last years. We were especially interested in the influence of different bridging groups such as ether, ketone, and sulfone groups. The affect on properties such as water uptake (WU), thermal stability, proton conductivity, and oxidative stability were analyzed in this work. Additionally, the blend membranes were characterized by gel permeation chromatography. The novel SPSO blend shows a high molecular weight, and its blend membrane with PBIOO has an excellent onset of ? SO₃H group splitting‐off temperature (T_onset) of 334 °C. The proton conductivity amounts to 0.11 S cm^?1, and the water uptake reaches 30%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of fluorine‐containing polybenzimidazole for proton conducting membranes in fuel cells

Two new kinds of fluorine‐containing polybenzimidazoles (PBI), poly(2,2′‐(tetrafluoro‐p‐phenylene)‐5,5′‐bibenzimidazole) and poly(2,2′‐tetradecafluoroheptylene‐5,5′‐bibenzimidazole), were synthesized by condensation polymerization of 3,3′‐diaminobenzidine and perfluoroterephthalic acid (or perfluoroazelaic acid), with polyphosphoric acid as solvent. Thermogravimetric analysis results show that the fluorine‐containing polymers synthesized exhibit promising thermal stability. The film‐forming properties of the fluorine‐containing polymers are improved over nonfluorinated PBI. The introduction of fluorine into the backbone of the polymers has significant positive affection on their chemical oxidation stability demonstrated by Fenton test. Compared with poly(2,2′‐(m‐phenylene)‐5,5′‐bibenzimidazole)/phosphoric acid (PA) composite membrane, the resulting fluorinated membranes with a same PA doping level exhibit better flexibility and higher proton conductivity. The maximum proton conductivity gained is 3.05 × 10^?2 S/cm at 150 °C with a PA doping level of 7. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2115–2122, 2010     

Low glass transition temperature polymer electrolyte prepared from ionic liquid grafted polyethylene oxide

In this contribution, we report a new type of poly (ionic liquids) prepared by imidazolium ionic liquids directly grafting onto polyethylene oxide backbone. Different molecular weights of poly (ionic liquids) are obtained with a low glass transition temperature up to ?14 °C. The materials as polymer electrolyte achieve a high conductivity around 10^?5 S cm^?1 at 30 °C and close to 10^?3 S cm^?1 at 90 °C. High viscosity up to 4000 Pa s at room temperature would minimize the electrolytes leaking in electrochemical devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2104–2110     

Synthesis of partially fluorinated poly(arylene ether sulfone) multiblock copolymers bearing perfluorosulfonic functions

Partially fluorinated poly(arylene ether sulfone) multiblock copolymers bearing perfluorosulfonic functions (ps‐PES‐FPES), with ionic exchange capacity (IEC) ranging between 0.9 and 1.5 meq H⁺/g, are synthesized by regioselective bromination of partially fluorinated poly(arylene ether sulfone) multiblock copolymers (PES‐FPES), followed by Ullman coupling reaction with lithium 1,1,2,2‐tetrafluoro‐2‐(1,1,2,2‐tetrafluoro‐2‐iodoethoxy)ethanesulfonate. The PES‐FPES are prepared by aromatic nucleophilic substitution reaction by an original approach, that is, “one pot two reactions synthesis.” The chemical structures of polymers are analyzed by ¹H and ¹⁹F NMR spectroscopy. The resulted ionomers present two distinct glass transitions and α relaxations revealing phase separation between the hydrophilic and the hydrophobic domains. The phase separation is observed at much lower block lengths of ps‐PES‐FPES as compared with the literature. AFM and SANS observations supported the phase separation, the hydrophilic domains are well dispersed but the connectivity to each other depends on the ps‐PES block lengths. The thermomechanical behavior, the water up‐take, and the conductivity of the ps‐PES‐FPES membranes are compared with those of Nafion 117^® and randomly functionalized polysulfone (ps‐PES). Conductivities close or higher to those of Nafion 117^® are obtained. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1941–1956     

Synthesis and healing properties of poly(arylene ether sulfone)‐poly(alkyl disulfide) multiblock copolymers

A multiblock copolymer consisting of hard (poly(arylene ether sulfone)) and soft (poly(alkyl disulfide)) segments was successfully synthesized by oxidative coupling of the corresponding thiol‐terminated oligomers. Its structure was confirmed by ¹H and ¹³C NMR spectroscopy. The GPC data (M_w = 82,000, M_w/M_n = 2.7) and inherent viscosity (0.67 dL g⁻¹) indicated the formation of a high‐molecular‐weight multiblock copolymer, while AFM and DSC indicated a microphase‐separated morphology. Tensile testing of the multiblock copolymer films showed a large elongation at break, which is characteristic of microphase‐separated hard/soft multiblock copolymers. Over 90% of the elongation at break of damaged samples (notched or cut) was recovered by UV irradiation. The elongation recovery was proportional to the UV irradiation energy, and the high recovery was achieved by relatively weak irradiation (<170 J cm⁻²). The high content of disulfide bonds in the multiblock copolymer resulted in a lower self‐healing energy. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1358–1365     

Rigid Coplanar Polymers for Stable n‐Type Polymer Thermoelectrics

Low n‐doping efficiency and inferior stability restrict the thermoelectric performance of n‐type conjugated polymers, making their performance lag far behind of their p‐type counterparts. Reported here are two rigid coplanar poly(p‐phenylene vinylene) (PPV) derivatives, LPPV‐1 and LPPV‐2 , which show nearly torsion‐free backbones. The fused electron‐deficient rigid structures endow the derivatives with less conformational disorder and low‐lying lowest unoccupied molecular orbital (LUMO) levels, down to ?4.49 eV. After doping, two polymers exhibited high n‐doping efficiency and significantly improved air stability. LPPV‐1 exhibited a high conductivity of up to 1.1 S cm^?1 and a power factor as high as 1.96 μW m^?1 K^?2. Importantly, the power factor of the doped LPPV‐1 thick film degraded only 2 % after 7 day exposure to air. This work demonstrates a new strategy for designing conjugated polymers, with planar backbones and low LUMO levels, towards high‐performance and potentially air‐stable n‐type polymer thermoelectrics.     

Surface‐initiated ring‐opening polymerization of p‐dioxanone on Wang resin bead

Biodegradable poly(p‐dioxanone) (PPDO) was formed on Wang resin surface by surface‐initiated ring‐opening polymerization (SI‐ROP). The SI‐ROP of p‐dioxanone (PDO) was achieved by heating a mixture of Tin(II) bis(2‐ethylhexanoate) [Sn(Oct)₂], hydroxyl functionalized Wang resin, and PDO in anhydrous toluene at 80 °C. The resultant polymer‐grafted Wang resin (Wang‐g‐PPDO) was characterized by fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), optical microscopy (OM), and field‐emission scanning electron microscopy (FE‐SEM). The FTIR spectra of Wang‐g‐PPDO show peak characteristic of PPDO at 2943 cm^?1 (? C? H stretch), at 1741 cm^?1 (? C?O stretch), and 1136 cm^?1 (C? O? C stretch) indicating the formation of ester linkage between PPDO and hydroxyl terminated Wang resin. The DSC thermogram show melting peak corresponding to PPDO polymer on Wang resin surface. Thermogravimetric investigation shows increase in PPDO content on the Wang resin surface in terms of percentage of weight loss with increase in reaction time. The OM and SEM photographs clearly show the formation of PPDO polymer on the Wang resin surface without altering the spherical nature of Wang resin bead. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1178–1184, 2008     

Thermal lensing in poly(vinyl alcohol)/polyaniline blends

Nonlinear optical properties of poly(vinyl alcohol) (PVA)/polyaniline (PAni) blends were measured with the single‐beam Z‐scan technique with Fourier analysis. The results obtained with continuous wave (cw) excitation indicated that the self‐phase modulation had a thermal origin. Besides the Z‐scan technique, we also employed the time‐resolved mode‐mismatched thermal lens (TL) technique to obtain the temperature coefficient of the optical path length, ds/dT, and the thermal diffusivity coefficient, D, for the specific concentrations used in our blends. ds/dT varied between ?0.8 and ?1.0 × 10^?4 K^?1, whereas the thermal diffusivity varied between 1.0 and 1.3 × 10^?3 cm²/s. The TL technique was further used to study the aging of the blends as they were heated to 90 °C. Unlike the electrical conductivity of PAni films, which presented a strong dependence on the doping level, the thermooptic properties presented only a slight variation with doping. This feature indicated that the PVA/glutaraldehyde network made the main contribution to the thermooptic properties (D and ds/dT) in the PAni blends. Similarly, dimethyl sulfoxide as a solvent determined the thermooptic properties of PAni solutions. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1949–1956, 2002     

Synthesis and proton conductivities of phosphonic acid containing poly‐(arylene ether)s

A novel phosphonic acid containing bisphenol was successfully synthesized from phenolphthalein and m‐aminophenylphosphonic acid. A series of homo‐ and copoly‐(arylene ether)s containing phosphonic acid groups were prepared by solution nucleophilic polycondensation. These phosphonic acid containing polymers can readily be dissolved in common organic solvents, such as dimethyl sulfoxide, N‐methyl‐2‐pyrrolidinone, and N‐cyclohexylpyrrolidinone, and can be cast into tough and smooth films. The presence of phosphonic acid pendants in the poly‐(arylene ether)s was confirmed by NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, and conductivity measurements. This is the first report on the attachment of phenylphosphonic acid groups as side chains to aromatic polyethers. These poly‐(arylene ether)s had very high glass‐transition temperatures ranging from 254 to >315 °C and high molecular weights. The conductivities of the synthesized polymers were analyzed by the Cole–Cole method, and they ranged from 10^?5 to 10^?6 Scm^?1. The synthesized polymers also exhibited good solution processability. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3218–3226, 2001