Real time laser interference microscopy for bar‐spread polystyrene/poly(methyl methacrylate) blends

We demonstrate that real‐time laser interference microscopy can be used to directly observe the dynamics of film formation and phase separation processes for a bar‐spread polystyrene/poly(methyl methacrylate) blend. The ability to dynamically image laser interference patterns allows compete drying curves and polymer content to be determined throughout the film formation process. The polymer content at which phase separation structure first is observed in the interference micrograph sequence is in good agreement with calculated spinodal curves. Morphology evolution proceeds from phase separation onward via coarsening and coalescence to arrive at the final domain structure. In comparison, spin coating the same polymer blend results in structure evolution being quenched further from equilibrium due to the faster drying rate. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 985–992     

One‐step synthesis of polymer micro‐tubes tethered by polymer nanowire networks via RAFT polymerization of N,N′‐methylene bisacrylamide xerogel fibers in toluene and ethanol mixed solution

In the mixed solution of toluene and ethanol, polymer micro‐tubes (PMTs) tethered by polymer nanowire networks (PTPWNs) were fabricated facilely via one‐step reversible addition fragmentation chain transfer (RAFT) polymerization by taking N,N′‐methylene bisacrylamide (MBA) xerogel fibers as both template and monomer source. The products were analyzed by FTIR, SEM, TEM, surface area and porosity analyzer, and contact angle tester. The results indicated that PTPWNs were obtained as the sole product at ethanol content of 1.0 wt %. As the content of ethanol increases from 0 to 1.0 wt %, the specific surface area of the products became higher, indicating more polymer nanowire networks (PWNs) on the tubes. At ethanol contents of 1.5 wt % and 2.0 wt %, some particles were also obtained besides PTPWNs. The formation process of PTPWNs was studied by analyzing the products obtained at different reaction time. The results revealed that PTPWNs were formed by two steps, PMTs were formed quickly and then PWNs formed in the solution tethered to the tubes. Moreover, the effect of RAFT agent on the morphologies of the products revealed that PTPWNs could be obtained via RAFT polymerization at suitable dosage of RAFT agent, while polymer particles were generated via conventional free radical polymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1862–1868     

Preparation and properties of polybenzoxazine/poly(imide‐siloxane) alloys: In situ ring‐opening polymerization of benzoxazine in the presence of soluble poly(imide‐siloxane)s

Benzoxazine monomer (Ba) was blended with soluble poly(imide‐siloxane)s in various weight ratios. The soluble poly(imide‐siloxane)s with and without pendent phenolic groups were prepared from the reaction of 2,2′‐bis(3,4‐dicarboxylphenyl)hexafluoropropane dianhydride with α,ω‐bis(aminopropyl)dimethylsiloxane oligomer (PDMS; molecular weight = 5000) and 3,3′‐dihydroxybenzidine (with OH group) or 4,4′‐diaminodiphenyl ether (without OH group). The onset and maximum of the exotherm due to the ring‐opening polymerization for the pristine Ba appeared on differential scanning calorimetry curves around 200 and 240 °C, respectively. In the presence of poly(imide‐siloxane)s, the exothermic temperatures were lowered: the onset to 130–140 °C and the maximum to 210–220 °C. The exotherm due to the benzoxazine polymerization disappeared after curing at 240 °C for 1 h. Viscoelastic measurements of the cured blends containing poly(imide‐siloxane) with OH functionality showed two glass‐transition temperatures (T_g's), at a low temperature around ?55 °C and at a high temperature around 250–300 °C, displaying phase separation between PDMS and the combined phase consisting of polyimide and polybenzoxazine (PBa) components due to the formation of AB‐crosslinked polymer. For the blends containing poly(imide‐siloxane) without OH functionalities, however, in addition to the T_g due to PDMS, two T_g's were observed in high‐temperature ranges, 230–260 and 300–350 °C, indicating further phase separation between the polyimide and PBa components due to the formation of semi‐interpenetrating networks. In both cases, T_g increased with increasing poly(imide‐siloxane) content. Tensile measurements showed that the toughness of PBa was enhanced by the addition of poly(imide‐siloxane). Thermogravimetric analysis showed that the thermal stability of PBa also was enhanced by the addition of poly(imide‐siloxane). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2633–2641, 2001     

Two‐dimensional polymer synthesis through the topochemical polymerization of alkylenediammonium muconate as a multifunctional monomer

Here we demonstrate a unique two‐dimensional polymer synthesis through topochemical polymerization via polymer crystal engineering, which is useful for controlling and designing the polymerization reactivity as well as the polymer chain and crystal structures. We have succeeded in the synthesis of a sheet polymer through the polymerization of alkylenediammonium (Z,Z)‐muconate as a multifunctional 1,3‐diene monomer in the crystalline state under the irradiation of UV and γ‐rays or upon heating in the dark. The photopolymerization reactivity of several muconates and the structural control of the obtained polymer are described. The stereochemical structure of the polymer and the polymerization mechanism are discussed on the basis of the results of IR and NMR spectroscopy, thermogravimetric measurements, and solid‐state hydrolysis for the transformation into poly(muconic acid). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3922–3929, 2004     

Simultaneous interpenetrating polymer networks based on epoxy–acrylate combinations

Simultaneous interpenetrating polymer networks (SINs) based on epoxy/poly(n-butyl acrylate) systems were synthesized at 120°C. The polymerization kinetics were studied both in situ by Fourier Transform Infrared Spectroscopy (FT–IR). Three key events occurred during the polymerization, namely the gelation of the network I, gelation of the network II, and phase separation of one polymer from the other. Thus, metastable phase diagrams describing the relations between the three events were constructed. Three-dimensional tetrahedrons characterizing the four-component system (the two monomers and the two polymers) allow the visualization of these three key events and also define some critical points, for example, the loci of the points where simultaneous gelation of the two networks occurs. The inside of the tetrahedron was also investigated using partially reacted model compounds. These tetrahedrons can be used as guidelines for setting up a synthesis strategy leading to desired morphologies. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1973–1984, 1997     

Aza‐Michael addition reaction: Post‐polymerization modification and preparation of PEI/PEG‐based polyester hydrogels from enzymatically synthesized reactive polymers

The utility of aza‐Michael addition chemistry for post‐polymerization functionalization of enzymatically prepared polyesters is established. For this, itaconate ester and oligoethylene glycol are selected as monomers. A Candida Antarctica lipase B catalyzed polycondensation reaction between the two monomers provides the polyesters, which carry an activated carbon‐carbon double bond in the polymer backbone. These electron deficient alkenes represent suitable aza‐Michael acceptors and can be engaged in a nucleophilic addition reaction with small molecular mono‐amines (aza‐Michael donors) to yield functionalized linear polyesters. Employing a poly‐amine as the aza‐Michael donor, on the other hand, results in the formation of hydrophilic polymer networks. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 745–749     

Synthesis and stability of BODIPY‐based fluorescent polymer brushes at different pHs

We report a simple strategy for the grafting of poly(methacrylic acid) [poly(MAA)] brushes from silicon substrate by surface‐initiated RAFT polymerization and the subsequent coupling of BODIPY to these brushes to render them fluorescent. The poly(MAA) brushes were first generated by functionalization of hydrogen‐terminated silicon substrate with methyl‐10‐undecenoate which both leads to the formation of an organic layer covalently linked to the surface via Si? C bonds without detectable reaction of the carboxylate groups and couples to the polymerization initiator, followed by surface‐initiated RAFT polymerization of tert‐butyl methacrylate from these substrate‐bound initiator centers, and finally conversion of tert‐butyl groups to carboxylic acid groups. The poly(MAA) brushes were then made fluorescent by grafting a BODIPY derivative via an ester linkage. The stability of the BODIPY‐based fluorescent polymer brushes in buffer solutions at pH 6.0 to 12.0 with added salt was investigated by ellipsometry, fluorescence microscopy, grazing angle‐Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy. The results of these measurements indicated that the organic molecule‐initiator bond (ester linkage) is unstable and can be hydrolyzed resulting in detaching of the immobilized polymer from the silicon substrate. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3586–3596     

Preparation of ureido group bearing polymers and their upper critical solution temperature in water

Poly(2‐ureidoethylmethacrylate) (PUEM_n) was synthesized via reversible addition‐fragmentation chain transfer (RAFT) radical polymerization and following polymer reaction. We prepared two PUEM_n samples with different degrees of polymerization (n = 100 and 49). The polymers exhibited upper critical solution temperature (UCST) in phosphate‐buffered saline (PBS) solution. The phase separation temperature (T_p) in PBS can be controlled ranging from 17 to 55 °C by changing molecular weight of the polymer, polymer concentration, and adding NaCl concentration. The polymers in PBS formed coacervate drops by liquid–liquid phase separations below T_p. Results of the dielectric relaxation measurement, the hydration number per monomeric unit was 5 above T_p. Based on a fluorescence study, the polymer formed slightly hydrophobic environments below T_p. The liquid–liquid phase separation was occurred presumably because of weak hydrophobic interactions and intermolecularly hydrogen bonding interactions between the pendant ureido groups. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2845–2854     

Radical polymerization of 2,5‐norbornadienes containing ester groups by AIBN and oxygen gas

New 2,5‐norbornadiene‐type monomers bearing 1‐adamantyl and cyclohexyl ester groups on their 2‐position polymerized with azobisisobutyronitrile to form the polymers consisting of two types of polymer unit structures. The major part had a saturated nortricyclene framework, which was formed by 2,6‐addition along with intramolecular cyclization on the norbornadiene moiety. The minor part consisted of 2‐norbornene‐type units constructed via 2,3‐addition. A series of norbornadiene‐based monomers spontaneously polymerized in the presence of oxygen. Because a radical inhibitor, namely hydroquinone, could suppress this spontaneous reaction, it was indicated that the oxygen‐induced polymerization proceeds via free‐radical polymerization mechanism. Changing a quantity of provided oxygen gas (O₂) to a norbornadiene monomer significantly affected on polymerization results, in specific, molecular weight of the formed polymer, which indicated that oxygen serves as one of the key reagents for the formation of free‐radical initiating species. It was proven that the combination of norbornadiene ethyl ester with O₂ was applicable as a new free‐radical initiator for polymerization of methyl methacrylate. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2528–2536     

Simulation of phase‐separated structures of liquid‐crystalline polymer/flexible polymer blends

The phase‐separation kinetics of liquid‐crystalline polymer/flexible polymer blends was studied by the coupled time‐dependent Ginzberg–Landau equations for compositional order parameter ? and orientational order parameter S_ij. The computer simulations of phase‐separated structures of the blends were performed by means of the cell dynamical system in two dimensions. The compositional ordering processes of phase separation are demonstrated by the time evolution of ?. The influence of orientational ordering on compositional ordering is discussed. The small‐angle light scattering patterns are numerically reproduced by means of the optical Fourier transformation of spatial variation of the polarizability tensor α_ij, and the azimuthal dependence of the scattering intensity distribution is interpreted. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2915–2921, 2001     

Attenuated total reflectance/fourier transform infrared studies on the phase‐separation process of aqueous solutions of poly(n‐isopropylacrylamide)

Temperature‐induced phase separation of poly(N‐isopropylacrylamide) in aqueous solutions was studied by attenuated total reflectance (ATR)/Fourier transform infrared spectroscopy. The main objectives of the study were to understand, on a molecular level, the role of hydrogen bonding and hydrophobic effects below and above the phase‐separation temperature and to derive the scenario leading to this process. Understanding the behavior of this particular system could be quite relevant to many biological phenomena, such as protein denaturation. The temperature‐induced phase transition was easily detected by the ATR method. A sharp increase in the peaks of both hydrophobic and hydrophilic groups of the polymer and a decrease in the water‐related signals could be explained in terms of the formation of a polymer‐enriched film near the ATR crystal. Deconvolution of the amide I and amide II peaks and the O? H stretch envelope of water revealed that the phase‐separation scenario could be divided, below the phase‐separation temperature, into two steps. The first step consisted of the breaking of intermolecular hydrogen bonds between the amide groups of the polymer and the solvent and the formation of free amide groups, and the second step consisted of an increase in intramolecular hydrogen bonding, which induced a coil–globule transition. No changes in the hydrophobic signals below the separation temperature could be observed, suggesting that hydrophobic interactions played a dominant role during the aggregation of the collapsed chains but not before. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1665–1677, 2001     

Surfactant‐free synthesis of amphiphilic diblock copolymer in aqueous phase by a self‐stability process

Amphiphilic polymeric particles with hydrophobic cores and hydrophilic shells were prepared via living radical emulsion polymerization of styrene using a water‐soluble poly(acrylamide)‐based macro‐RAFT agent in aqueous solution in the absence of any surfactants. Firstly, the homopolymerization of acrylamide (AM) was carried out in aqueous phase by reversible addition‐fragmentation chain transfer radical polymerization (RAFT) using a trithiocarbonate as a chain transfer agent. Then the PAM‐based macro‐RAFT agent has been used as a water‐soluble macromolecular chain transfer agent in the batch emulsion polymerization of Styrene (St) free of surfactants. The RAFT controlled growth of hydrophobic block led to the formation of well‐defined poly(acrylamide)‐copolystyrene amphiphilic copolymer, which was able to work as a polymeric stabilizer (self‐stability). Finally, very stable latex was prepared, having no visible phase separation for several months. FTIR and ¹H‐NMR measurements showed that the product was the block copolymer PAM‐co‐PS in the form of stable latex. Atomic force microscope (AFM), transmission electron microscope (TEM), and dynamic light scattering (DLS) studies indicated that the nanoparticles have a narrow particle size distribution and the average particle hydrodynamic radius was kept in the diameter of 58 nm. Core‐shell structure of the copolymer was also recorded by TEM. The mechanism of the self‐stability of polymer particles during the polymerization in the absence of surfactants was studied. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3098–3107, 2008     

Small molecule self‐assembly in polymer matrices

Using small molecules in polymer matrices is common in applications such as (i) plasticizing polymers to modify the glass transition and mechanical properties and (ii) dispersion of photoactive or electroactive small molecules in polymer matrices in organic‐electronic devices Aggregation of these small molecules and phase separation leading to crystallization often cannot be morphologically controlled. If these are designed with self‐assembling codes such as hydrogen bonding or aromatic interactions, their phase separation behavior would be distinctly different. This review summarizes the studies on morphologies in such situations, such as (i) sub‐surface assembly in polymer matrices, (ii) controlled polymerization‐induced phase separation to create polymer blends, (iii) using the polymer to direct the assembly of small molecules in liquid crystalline devices, (iv) functionalizing a polymer with self‐assembling small molecules to cause organo‐gelation which the polymer itself would not by itself, and (v) using such systems as templates to create porous polymer structures. Organic–inorganic hybrids using polymers as templates for nanostructures and imprinted porous membranes is an emerging area. Since self‐assembly is one of the dominating area of research with respect to both small molecules, polymers as well as the combination of the two, this review summarizes the studies on the aforementioned topics. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 451–478     

Self‐assembly of star‐shaped polystyrene‐block‐polypeptide copolymers synthesized by the combination of atom transfer radical polymerization and ring‐opening living polymerization of α‐amino acid‐N‐carboxyanhydrides

The self‐assembling nature and phase‐transition behavior of a novel class of triarm, star‐shaped polymer–peptide block copolymers synthesized by the combination of atom transfer radical polymerization and living ring‐opening polymerization of α‐amino acid‐N‐carboxyanhydride are demonstrated. The two‐step synthesis strategy adopted here allows incorporating polypeptides into the usual synthetic polymers via an amido–amidate nickelacycle intermediate, which is used as the macroinitiator for the growth of poly(γ‐benzyl‐L ‐glutamate). The characterization data are reported from analyses using gel permeation chromatography and infrared, ¹H NMR, and ¹³C NMR spectroscopy. This synthetic scheme grants a facile way to prepare a wide range of polymer–peptide architectures with perfect microstructure control, preventing the formation of homopolypeptide contaminants. Studies regarding the supramolecular organization and phase‐transition behavior of this class of polymer‐block‐polypeptide copolymers have been accomplished with X‐ray diffraction, infrared spectroscopy, and thermal analyses. The conformational change of the peptide segment in the block copolymer has been investigated with variable‐temperature infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2774–2783, 2006     

Crystallization of polylactic acid under in situ deformation during nonsolvent‐induced phase separation

In this study, we investigate polylactic acid (PLA) crystallization under in situ biaxial extension in a nonsolvent‐induced phase separation foaming process. Our ternary system consists of PLA, dichloromethane (DCM) as solvent and hexane as nonsolvent. For the first time, the formation of a shish‐kebab crystalline morphology is observed in such a solution‐based foaming process in certain solid–liquid phase separated systems. The formation of shish‐kebabs is described based on the coil‐stretch transition concept. The rapid biaxial deformation caused by macropore growth uniaxially stretches the long chains that are tied with at least two single crystals which eventually leads to the formation of shish structures throughout the polymer‐rich phase. The kebab lamellae then form perpendicularly on the shish cores. The scanning electron microscopy (SEM) observations and our interpretation of the crystallization phenomena are confirmed by differential scanning calorimetry (DSC) analysis. The observation of various crystalline morphologies, particularly shish‐kebabs, and the elucidation of their formation mechanisms contribute to the understanding of phase separation and pore growth as well as crystallization in such polymer–solvent–nonsolvent systems. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1055–1062     

Controlled preparation of nanometer‐sized supramolecular cylinders of poly(ethylene oxide) embedded in methacrylate matrices

Semi‐interpenetrating networks of poly(ethylene oxide) (PEO) and highly crosslinked poly(methacrylate)s were generated from solutions of PEO in mixtures of methacrylate monomers and dimethacrylate crosslinkers. The deep quenching of the solutions into the unstable region resulted in microphase separation via a spinodal decomposition mechanism. Through the crystallization of the PEO inside the polymer‐rich phase, the domain size was reduced below the Cahn–Hilliard limit. The microstructure was permanently preserved by subsequent UV‐initiated polymerization of the monomers well below the PEO melting temperature. The semi‐interpenetrating networks were characterized by differential scanning calorimetry, small‐angle X‐ray scattering, NMR spin‐diffusion measurements, and electron microscopy. Morphologies based on networks of cylindrical PEO aggregates with diameters of 10 ± 2 nm were observed, nearly independent of the molecular weight of the used PEO. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2041–2056, 2000     

Consideration on formation mechanism of aromatic polyamide hollow spheres prepared by reaction‐Induced phase separation

Hollow spheres of poly(1,4‐phenylene‐5‐hydroxyisophthalamide) had been obtained by the reaction‐induced phase separation during polymerization of 5‐hydroxyisophthalic acid and 1,4‐phenylene diamine in an aromatic solvent. In this study, formation mechanism of the hollow spheres was considered from the view points of eliminated small molecules, polymer structure, and cross‐linking reaction. With respect to the eliminated small molecules, water was the most desirable to form gas‐bubbles in droplets compared with methanol and acetic acid, due to the insolubility into the polymerization system. Rigid polymer structure was also needed to prepare hollow spheres owing to the rapid solidification of droplets. Further, phenolic hydroxyl group in 5‐hydroxy‐1,3‐phenylene moiety caused the ester‐amide exchange reaction to form cross‐linked skin layer in the droplets. The efficient formation of the skin layer was important to encapsulate gas‐bubbles in the droplets, resulting in the formation of hollow structure. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1966–1974     

Solution processing of polymer semiconductor: Insulator blends—Tailored optical properties through liquid–liquid phase separation control

It has been demonstrated that the 0‐0 absorption transition of poly(3‐hexylthiophene) (P3HT) in blends with poly(ethylene oxide) (PEO) could be rationally tuned through the control of the liquid–liquid phase separation process during solution deposition. Pronounced J‐like aggregation behavior, characteristic for systems of a low exciton band width, was found for blends where the most pronounced liquid–liquid phase separation occurred in solution, leading to domains of P3HT and PEO of high phase purity. Since liquid–liquid phase separation could be readily manipulated either by the solution temperature, solute concentration, or deposition temperature, to name a few parameters, our findings promise the design from the out‐set of semiconductor:insulator architectures of pre‐defined properties by manipulation of the interaction parameter between the solutes as well as the respective solute:solvent system using classical polymer science principles. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 304–310     

Synthesis and characterization of crystalline graft polymer poly(ethylene oxide)‐g‐poly(ɛ‐caprolactone)2 with modulated grafting sites

The graft polymer poly(ethylene oxide)‐g‐poly(?‐caprolactone)₂ (PEO‐g‐PCL₂) with modulated grafting sites was synthesized by the combination of ring‐opening polymerization (ROP) mechanism, efficient Williamson reaction, with thiol–ene addition reaction. First, the precursor of PEO‐Allyl‐PEO with two terminal hydroxyl groups and one middle allyl group was prepared by ROP of EO monomers. Then, the macroinitiator [PEO‐(OH)₂‐PEO]_s was synthesized by sequential Williamson reaction between terminal hydroxyl groups and thiol–ene addition reaction on pendant allyl groups. Finally, the graft polymer PEO‐g‐PCL₂ was obtained by ROP of ?‐CL monomers using [PEO‐(OH)₂‐PEO]_s as macroinitiator. The target graft polymer and all intermediates were well characterized by the measurements of gel permeation chromatography, ¹H NMR, and thermal gravimetric analysis. The crystallization behavior was investigated by the measurements of differential scanning calorimetry, wide‐angle X‐ray diffraction and polarized optical microscope. The results showed that when the PCL content of side chains reached 59.2%, the crystalline structure had been dominated by PCL part and the crystalline structure formed by PEO part can be almost neglected. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2239–2247     

Influence of actinic wavelength on properties of light‐cured interpenetrating polymer networks

Interpenetrating polymer networks (IPNs) composed of different acrylate/epoxide ratios, were synthesized under UV and visible‐LED curing conditions. The formation of the IPNs was explored in terms of phase separation, polymerization mechanisms, final mechanical properties and surface morphology. For these purpose, we uniquely combined results of miscibility investigations, confocal Raman microscopy, dynamical mechanical analysis and atomic force microscopy. Transparent films were obtained for all compositions and both irradiation sources. The thermo‐mechanical properties of different IPNs were associated to the presence of acrylate‐ or epoxide‐rich phases, as well as, mixed interphases, resulting from the high interpenetration between both networks. Although the final conversions were similar under UV and visible‐LED irradiation, we have found evidence that the visible‐cured samples provide higher IPN homogeneity and lower T_g, for a higher epoxide content. To explain this trend, the mechanisms and sequence of the acrylate or epoxide networks formation, under UV or LED irradiation, is discussed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1378‐1390