Two‐sided comb poly(amic ester)–poly(propylene oxide) graft copolymers as porous polyimide precursors

New step‐growth graft block copolymers were synthesized. These two‐sided comb copolymers consisted of a poly(amic ester) (PAE) backbone and pendant poly(propylene oxide) (PPO) grafts. The copolymers were made via a macromonomer approach, in which the 4,6‐bischlorocarbonyl isophthalic acid bis[poly(propylene oxide)] ester macromonomer was synthesized through the reaction of hydroxyl‐terminated PPO oligomers with pyromellitic dianhydride and oxalyl chloride. This macromonomer was subsequently used in step‐growth polymerization with comonomers 4,6‐bischlorocarbonyl isophthalic acid diethyl ester, 2,5‐bischlorocarbonyl terephthalic acid diethyl ester, and 2,2‐bis[4‐ (4‐aminophenoxy)phenyl] hexafluoropropane, and this yielded PPO‐co‐PAE graft copolymers. Accordingly, we report the synthesis and characterization of the PPO oligomer, the PPO macromonomer, and their corresponding PPO‐co‐PAE graft copolymers. Graft copolymers with PPO concentrations of 3–26 wt % were synthesized. These polymers were thermally cured to produce polyimide/PPO composites. The thermolysis of these polyimide/PPO composites yielded porous polyimide films with porosities ranging of 4–22.5%. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2266–2275, 2005     

Segmented block copolymers based on poly(propylene oxide) and monodisperse polyamide‐6,T segments

Polyether(ester amide)s with poly(propylene oxide) (PPO) and monodisperse poly(hexamethylene terephthalamide) segments were synthesized, and their structure–property relations were investigated. The length of the amide segments was varied from diamide to tetraamide to hexaamide segments, and therefore the number hydrogen bonds per amide segment increased from two to four to six. PPO was end‐capped with 20 wt % ethylene oxide and had number‐average molecular weights of 1000, 2300, and 4000 g/mol (including ethylene oxide tips). The morphology of the poly‐ether(ester amide)s was studied with transmission electron microscopy and atomic force microscopy, the thermal properties were studied with differential scanning calorimetry and dynamic mechanical thermal analysis, and the tensile properties were studied with dumbbell samples. The elastic behavior of the block copolymers was investigated with tensile and compression tests. These segmented copolymers had two sharp transitions: a glass‐transition temperature (T_g) of the PEO–PPO–PEO phase [where PEO is poly(ethylene oxide)] and a melting temperature (T_m) of the amide segments. The amide segments crystallized in nanoribbons with a high aspect ratio 1000. T_m increased with the amide segment length and with decreasing PEO–PPO–PEO content (solvent effect). The modulus increased strongly with the amide content. This modulus increase could be described by the Halpin–Tsai fiber composite model. Increasing the amide segment length surprisingly also improved the elasticity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4769–4781, 2006     

Poly(ether tert‐amine): A novel family of multiresponsive polymer

A novel multiresponsive poly(ether tert‐amine) (PEA) was synthesized by nucleophilic addition/ring‐opening reaction of commercial poly(ethylene oxide) (PEO), poly(propylene oxide) (PPO), and di‐epoxy and di‐amine monomer. The process of synthesis was very simple and green in ethanol as reactive media. These PEAs exhibit sharp response to temperature, pH, and ionic strength, with adjustable and sharp phase transitions in the range of 27–100 °C. The lower critical solution temperature (LCST) of PEA's aqueous solution presents a linear relationship to the PEO content (y = 35.7 + x), indicating well‐tunable LCST. The concentration of PEA has no obvious effect on LCST. Therefore, PEA will be potential in applications of drug delivery, separation, and biotechnology. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1292–1297, 2009     

Novel family of triphenylamine‐containing,hole‐transporting,amorphous, aromatic polyamides with stable electrochromic properties

We report the preparation and characterization of a series of novel electrochromic, aromatic poly(amine amide)s with pendent triphenylamine units. The synthesis proceeded via direct phosphorylation polycondensation between a novel diamine, N,N‐bis(4‐aminophenyl)‐N′,N′‐diphenyl‐1,4‐phenylenediamine, and various aromatic dicarboxylic acids. All the poly(amine amide)s were amorphous and readily soluble in many common organic solvents and could be solution‐cast into transparent, tough, and flexible films with good mechanical properties. They exhibited good thermal stability and 10% weight‐loss temperatures above 540 °C. Their glass‐transition temperatures were 263–290 °C. These polymers in N‐methyl‐2‐pyrrolidinone solutions exhibited strong ultraviolet–visible absorption peaks at 307–358 nm and photoluminescence peaks around 532–590 nm in the green region. The hole‐transporting and electrochromic properties were studied with electrochemical and spectroelectrochemical methods. Cyclic voltammograms of poly(amine amide) films prepared by the casting of polymer solutions onto an indium tin oxide coated glass substrate exhibited two reversible oxidation redox couples at 0.65 and 1.03 V versus Ag/AgCl in an acetonitrile solution. All the poly(amine amide)s showed excellent stability with respect to their electrochromic characteristics; the color of the films changed from pale yellow to green and then blue at 0.85 and 1.25 V, respectively. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2085–2098, 2005     

Synthesis and characterization of poly(urethane‐benzoxazine) films as novel type of polyurethane/phenolic resin composites

Poly(urethane‐benzoxazine) films as novel polyurethane ( PU )/phenolic resin composites were prepared by blending a benzoxazine monomer ( Ba ) and PU prepolymer that was synthesized from 2,4‐tolylene diisocyanate (TDI) and polyethylene adipate polyol (MW ca. 1000) in 2 : 1 molar ratio. DSC of PU/Ba blend showed an exotherm with maximum at ca. 246 °C due to the ring‐opening polymerization of Ba, giving phenolic OH functionalities that react with isocyanate groups in the PU prepolymer. The poly(urethane‐benzoxazine) films obtained by thermal cure were transparent, with color ranging from yellow to pale wine with increase of Ba content. All the films have only one glass transition temperature (T_g ) from viscoelastic measurements, indicating no phase separation in poly(urethane‐benzoxazine) due to in situ polymerization. The T_g increased with the increase of Ba content. The films containing 10 and 15% of Ba have characteristics of an elastomer, with elongation at break at 244 and 182%, respectively. These elastic films exhibit good resilience with excellent reinstating behavior. The films containing more than 20% of Ba have characteristics of plastics. The poly(urethane‐benzoxazine) films showed excellent resistance to the solvents such as tetrahydrofuran, N,N‐dimethyl formamide, and N‐methyl‐2‐pyrrolidinone that easily dissolve PU s. Thermal stability of PU was greatly enhanced even with the incorporation of a small amount of Ba . © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4165–4176, 2000     

Synthesis of triblock and multiblock methacrylate polymers and self‐assembly of stimuli responsive triblock polymers

Multisegmented poly(methacrylate)s were synthesized using one pot reversible addition fragmentation chain transfer polymerization. Initially, a series of triblock copolymers were synthesized with different ratios of trimethylsilyl methacrylate, di(ethylene oxide) methacrylate, and oligo(ethylene oxide) methacrylate, and different total polymer molecular weights. Additionally, a polymer containing seven distinct blocks of methacrylic monomers was synthesized in one pot. For the triblock copolymers, the trimethylsilyl group was subsequently hydrolyzed, and the self‐assembly of the triblock copolymer was studied in water, under different pH and thermal conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2548–2555     

Nanostructured polybenzoxazine thermosets via reaction‐induced microphase separation

A multiblock copolymer consisting of main‐chain polybenzoxazine and poly(propylene oxide) blocks was synthesized via Mannich polycondensation among 4,4′‐dihydroxyldiphenylisopropane, 4,4′‐diaminodiphenylmethane, amino‐terminated poly(propylene oxide), and paraformaldehyde, which was evidenced by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy, and gel permeation chromatography. The multiblock copolymer was incorporated into polybenzoxazine to access the nanostructured polybenzoxazine thermosets. The morphology of the thermosets was investigated by means of atomic force microscopy and small angle X‐ray scattering. It was judged that the formation of the nanostructures in the thermosetting composites follows the mechanism of reaction‐induced microphase separation. Owing to the big difference in thermal stability between polybenzoxazine thermosets and poly(propylene oxide), the nanostructured thermosets were subjected to the pyrolysis at moderate elevated temperatures to remove poly(propylene oxide) microdomains, to access the nanoporous polybenzoxazine thermosets. The nanoporosity of the resulting polybenzoxazine thermosets was investigated by means of Fourier transform infrared spectroscopy and field‐emission scanning electronic microscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1148–1159, 2010     

Synthesis of new thermosetting poly(2,6‐dimethyl‐1,4‐phenylene oxide)s containing epoxide pendant groups

A new class of thermosetting poly(2,6‐dimethyl‐1,4‐phenylene oxide)s containing pendant epoxide groups were synthesized and characterized. These new epoxy polymers were prepared through the bromination of poly(2,6‐dimethyl‐1,4‐phenylene oxide) in halogenated aromatic hydrocarbons followed by a Wittig reaction to yield vinyl‐substituted polymer derivatives. The treatment of the vinyl‐substituted polymers with m‐chloroperbenzoic acid led to the formation of epoxidized poly(2,6‐dimethyl‐1,4‐phenylene oxide) with variable pendant ratios, and the structures and properties were studied with nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, and gel permeation chromatography. The ratios of pendant functional groups were tailored for the polymer properties, and the results showed that the glass‐transition temperatures increased as the benzylic protons were replaced by bromo‐, vinyl‐, or epoxide‐functional groups, whereas the thermal stability decreased in comparison with the original polymer. Within a molar fraction of 20–50%, the degree of functionalization had little effect on the glass‐transition temperature; however, it correlated inversely with the thermal stability of each functionalized polymer. The thermal curing behavior of the epoxide‐functionalized polymer was enhanced by the increment of the pendant functionality, which resulted in a significant increase in the glass‐transition temperature as well as the thermal stability after the curing reaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5875–5886, 2006     

Heteroarm H‐shaped terpolymers through the combination of the Diels–Alder reaction and controlled/living radical polymerization techniques

Heteroarm H‐shaped terpolymers (PS)(PtBA)–PEO–(PtBA)(PS) and (PS)(PtBA)–PPO–(PtBA)(PS) [where PS is polystyrene, PtBA is poly(tert‐butyl acrylate), PEO is poly(ethylene oxide), and PPO is poly(propylene oxide)], containing PEO or PPO as a backbone and PS and PtBA as side arms, were prepared via the combination of the Diels–Alder reaction and atom transfer radical and nitroxide‐mediated radical polymerization routes. Commercially available PEO or PPO containing bismaleimide end groups was reacted with a compound having an anthracene functionality, succinic acid anthracen‐9‐yl methyl ester 3‐(2‐bromo‐2‐methylpropionyloxy)‐2‐methyl‐2‐[2‐phenyl‐2‐(2,2,6,6‐tetramethylpiperidin‐1‐yloxy)ethoxycarbonyl]propyl ester, with a Diels–Alder reaction strategy. The obtained macroinitiator with tertiary bromide and 2,2,6,6‐tetramethylpiperidin‐1‐oxy functional end groups was used subsequently in the atom transfer radical polymerization of tert‐butyl acrylate and in the nitroxide‐mediated free‐radical polymerization of styrene to produce heteroarm H‐shaped terpolymers with moderately low molecular weight distributions (<1.31). The polymers were characterized with ¹H NMR, ultraviolet, gel permeation chromatography, and differential scanning calorimetry. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3947–3957, 2006     

Biobased poly(2,5‐furandimethylene succinate‐co‐butylene succinate) crosslinked by reversible Diels–Alder reaction

We synthesized biobased poly(2,5‐furandimethylene succinate‐co‐butylene succinate) [P(FS‐co‐BS)] copolymers by polycondensation of 2,5‐bis(hydroxymethyl)furan, 1,4‐butanediol, and succinic acid. These copolymers could be crosslinked to form network polymers by means of a reversible Diels–Alder reaction with bis‐maleimide. The thermal properties, mechanical properties, and healing abilities of the P(FS‐co‐BS)s and the network polymers were investigated. The mechanical properties of the network polymers depended on the comonomer composition of the P(FS‐co‐BS)s and the maleimide/furan ratio in the network polymers. Some of the copolymers exhibited healing ability at room temperature, and their healing efficiency was enhanced by solvent or heat. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 216–222     

Multistimuli responsive grafted poly(ether tert‐amine) (gPEA): Synthesis,characterization and controlled morphology in aqueous solution

Multistimuli responsive grafted poly(ether tert‐amine) (gPEAs), which were comprised of poly(propylene oxide) (PPO) in backbone and poly(ethylene oxide) (PEO) as grafted chain, were successfully synthesized through nucleophilic addition/ring‐opening reaction of commercial poly(propylene glycol) diglycidyl ether and Jeffamine L100. These gPEAs exhibit very sharp response to temperature, pH and ionic strength with tunable cloud point (CP). The CP of gPEA aqueous solution increases with increasing the PEO content or decreasing pH value, varying from 27 to 77 °C. Compared with linear PEA101, gPEA110 of completely grafted structure in aqueous solution exhibits sharper response to temperature with ΔT around 1 °C. The results obtained from TEM and dynamic light scattering reveal that gPEAs are dispersed as uniform sized nano‐micelles in aqueous at room temperature, which can further aggregate into mesoglobules of complex structure at high temperature (>CP). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6353–6361, 2009     

Synthesis of a new class of triphenylamine‐containing poly(ether‐imide)s for electrochromic applications

A novel triphenylamine (TPA)‐containing bis(ether anhydride) monomer, namely 4,4′‐bis(3,4‐dicarboxyphenoxy)triphenylamine dianhydride, was synthesized and reacted with various aromatic diamines leading to a series of new poly(ether‐imide)s (PEI). Most of these PEIs were soluble in organic solvents and could be easily solution cast into flexible and strong films. The polymer films exhibited good thermal stability with glass‐transition temperatures in the range 211–299 °C. The polymer films exhibited reversible electrochemical processes and stable color changes (from transparent to navy blue) with high coloration efficiency and contrast ratio upon electro‐oxidation. During the electrochemical oxidation process, a crosslinked polymer structure was developed due to the coupling reaction between the TPA radical cation moieties in the polymer chains. These polymers can be used to fabricate electrochromic devices with high coloration efficiency, high redox stability, and fast response time. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 825–838     

Synthesis and characterization of fluorinated poly(amide imide)s derived from 1,4‐bis(2′‐trifluoromethyl‐4′‐trimellitimidophenoxy)benzene and aromatic diamines

A series of fluorinated poly(amide imide)s were prepared from 1,4‐bis(2′‐trifluoromethyl‐4′‐trimellitimidophenoxy)benzene and various aromatic diamines [3,3′,5,5′‐tetramethyl‐4,4′‐diaminediphenylmethane, α,α‐bis(4‐amino‐3,5‐dimethyl phenyl)‐3′‐trifluoromethylphenylmethane, 1,4‐bis(4′‐amino‐2′‐trifluoromethylphenoxy)benzene, 4‐(3′‐trifluoromethylphenyl)‐2,6‐bis(3′‐aminophenyl)pyridine, and 1,1‐bis(4′‐aminophenyl)‐1‐(3′‐trifluoromethylphenyl)‐2,2,2‐trifluoroethane]. The fluorinated poly(amide imide)s, prepared by a one‐step polycondensation procedure, had good solubility both in strong aprotic solvents, such as N‐methyl‐2‐pyrrolidinone, dimethylacetamide, dimethylformamide, dimethyl sulfoxide, and cyclopentanone, and in common organic solvents, such as tetrahydrofuran and m‐cresol. Strong and flexible polymer films with tensile strengths of 84–99 MPa and ultimate elongation values of 6–9% were prepared by the casting of polymer solutions onto glass substrates, followed by thermal baking. The poly(amide imide) films exhibited high thermal stability, with glass‐transition temperatures of 257–266 °C and initial thermal decomposition temperatures of greater than 540 °C. The polymer films also had good dielectric properties, with dielectric constants of 3.26–3.52 and dissipation factors of 3.0–7.7 × 10^?3, and acceptable electrical insulating properties. The balance of excellent solubility and thermal stability associated with good mechanical and electrical properties made the poly(amide imide)s potential candidates for practical applications in the microelectronics industry and other related fields. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1831–1840, 2003     

Insights into poly(3‐hexylthiophene)‐b‐poly(ethylene oxide) block copolymer: Synthesis and solvent‐induced structure formation in thin films

We report the synthesis, characterization, and solvent‐induced structure formation in thin films of an amphiphilic rod‐coil conjugated block copolymer, poly(3‐hexylthiophene)‐b‐poly(ethylene oxide). The diblock copolymers were prepared by a facile click reaction and their characterizations as well as thermal, crystalline, optical properties, and self‐assembly behavior have been investigated in detail. A series of morphologies including two‐phase separated nanostructure, nanofibrils, and their mixed morphology could be obtained depending on the selectivity of solvents to different blocks. Structural analyses demonstrate there is a subtle balance between microphase separation of copolymer and the π‐π stacking of the conjugated P3HT and such balance can be controlled by changing the solvents of different selectivity in solution and the length of P3HT block. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis,optical properties,and electroluminescence of conjugated poly(p‐phenylenevinylene) derivatives containing 1,3,4‐oxadiazole and pyridine rings in the main chain

Three new poly(p‐phenylenevinylene) derivatives—PO, POD, and POP—with oxadiazole and pyridine rings along the main chain were synthesized via Heck coupling. The polymers were amorphous and dissolved readily in common organic solvents. They showed relatively low glass‐transition temperatures (up to 42 °C) and satisfactory thermal stability. Solutions of the polymers emitted blue‐greenish light with photoluminescence (PL) emission maxima around 460 nm and PL quantum yields of 0.28–0.49. Thin films of the polymers displayed PL emission maxima at 461–521 nm, and their tendency to form aggregates was significantly influenced by the chemical structure. Light‐emitting diodes with polymers PO and POP, with an indium tin oxide/poly(ethylenedioxythiophene) (PEDOT)/polymer/Ca configuration, emitted yellow and green light, respectively, and this could be attributed to excimer emission. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3212–3223, 2004     

9,9‐Diaryl‐4,5‐diazafluorene‐based Cardo polymer; Synthesis and characteristic properties

To open out new aspects of 9,9‐diarylfluorene (DAF)‐based polymers with high performances, 9,9‐(4‐hydroxyphenyl)‐4,5‐diazafluorene ( N‐BPF ) was designed as a new cardo structure and the properties of poly(ether ketone)s ( N‐PEKs ) containing N‐BPF skeletons were examined in detail. N‐PEKs were synthesized in high yields via polycondensation of N‐BPF with difluoroarenes. N‐PEKs showed cardo polymer‐specific properties such as high thermal stability and high solubility in organic solvents. The addition of p‐toluenesulfonic acid (TsOH) to N‐PEK resulted in the formation of network polymer based on interchain hydrogen bonds. It turned out that the films of network polymer are flexible and transparent and exhibit high refractive index and low birefringence. The effects of feed ratio of TsOH to N‐PEK were also evaluated on the mechanical properties of network polymer. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4541–4549     

New polymer organogelators with L‐isoleucine and L‐valine as a gelation‐causing segment: Organogelation by a combination of supramolecular polymer and conventional polymer

New polymer organogelators, which are composed of poly(ethylene glycol), poly(propylene glycol), and poly(dimethylsiloxane)s as a polymer segment and L ‐isoleucine and L ‐valine derivatives as a gelation‐causing segment, were synthesized, and their organogelation properties were examined in organic solvents and oils. These polymer organogelators formed organogels in many organic solvents and oils, and their gels were thermally stable and had a high mechanical strength. Furthermore, the effects of the polymer backbone on the organogelation is discussed using FTIR spectroscopy, field emission scanning electron microscope observation, and analysis of thermal stability and strength of the organogel. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 353–361, 2008     

Preparation and properties of polybenzoxazine/poly(imide‐siloxane) alloys: In situ ring‐opening polymerization of benzoxazine in the presence of soluble poly(imide‐siloxane)s

Benzoxazine monomer (Ba) was blended with soluble poly(imide‐siloxane)s in various weight ratios. The soluble poly(imide‐siloxane)s with and without pendent phenolic groups were prepared from the reaction of 2,2′‐bis(3,4‐dicarboxylphenyl)hexafluoropropane dianhydride with α,ω‐bis(aminopropyl)dimethylsiloxane oligomer (PDMS; molecular weight = 5000) and 3,3′‐dihydroxybenzidine (with OH group) or 4,4′‐diaminodiphenyl ether (without OH group). The onset and maximum of the exotherm due to the ring‐opening polymerization for the pristine Ba appeared on differential scanning calorimetry curves around 200 and 240 °C, respectively. In the presence of poly(imide‐siloxane)s, the exothermic temperatures were lowered: the onset to 130–140 °C and the maximum to 210–220 °C. The exotherm due to the benzoxazine polymerization disappeared after curing at 240 °C for 1 h. Viscoelastic measurements of the cured blends containing poly(imide‐siloxane) with OH functionality showed two glass‐transition temperatures (T_g's), at a low temperature around ?55 °C and at a high temperature around 250–300 °C, displaying phase separation between PDMS and the combined phase consisting of polyimide and polybenzoxazine (PBa) components due to the formation of AB‐crosslinked polymer. For the blends containing poly(imide‐siloxane) without OH functionalities, however, in addition to the T_g due to PDMS, two T_g's were observed in high‐temperature ranges, 230–260 and 300–350 °C, indicating further phase separation between the polyimide and PBa components due to the formation of semi‐interpenetrating networks. In both cases, T_g increased with increasing poly(imide‐siloxane) content. Tensile measurements showed that the toughness of PBa was enhanced by the addition of poly(imide‐siloxane). Thermogravimetric analysis showed that the thermal stability of PBa also was enhanced by the addition of poly(imide‐siloxane). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2633–2641, 2001     

Synthesis and characterization of crystalline graft polymer poly(ethylene oxide)‐g‐poly(ɛ‐caprolactone)2 with modulated grafting sites

The graft polymer poly(ethylene oxide)‐g‐poly(?‐caprolactone)₂ (PEO‐g‐PCL₂) with modulated grafting sites was synthesized by the combination of ring‐opening polymerization (ROP) mechanism, efficient Williamson reaction, with thiol–ene addition reaction. First, the precursor of PEO‐Allyl‐PEO with two terminal hydroxyl groups and one middle allyl group was prepared by ROP of EO monomers. Then, the macroinitiator [PEO‐(OH)₂‐PEO]_s was synthesized by sequential Williamson reaction between terminal hydroxyl groups and thiol–ene addition reaction on pendant allyl groups. Finally, the graft polymer PEO‐g‐PCL₂ was obtained by ROP of ?‐CL monomers using [PEO‐(OH)₂‐PEO]_s as macroinitiator. The target graft polymer and all intermediates were well characterized by the measurements of gel permeation chromatography, ¹H NMR, and thermal gravimetric analysis. The crystallization behavior was investigated by the measurements of differential scanning calorimetry, wide‐angle X‐ray diffraction and polarized optical microscope. The results showed that when the PCL content of side chains reached 59.2%, the crystalline structure had been dominated by PCL part and the crystalline structure formed by PEO part can be almost neglected. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2239–2247     

Thermal gelation or gel melting: (ethylene glycol)113‐(l‐alanine)12 and (ethylene glycol)113‐(l‐lactic acid)12

When PEG (M.W.～5000 Daltons) is conjugated to poly(l ‐alanine), the polymer aqueous solutions (<10.0 wt.%) undergo sol‐to‐gel (thermal gelation), whereas it is conjugated to poly(l ‐lactic acid), the polymer aqueous solutions (>30.0 wt.%) undergo gel‐to‐sol (gel melting) as the temperature increases. In the search for molecular origins of such a quite different phase behavior, poly(ethylene glycol)‐poly(l ‐alanine) (PEG‐PA; EG₁₁₃‐A₁₂) and poly(ethylene glycol)‐poly(l ‐lactic acid) (PEG‐PLA; EG₁₁₃‐LA₁₂) are synthesized and their aqueous solution behavior is investigated. PEG‐PAs with an α‐helical core assemble into micelles with a broad size distribution, and the dehydration of PEG drives the aggregation of the micelles, leading to thermal gelation, whereas increased molecular motion of the PLA core overwhelms the partial dehydration of PEG, thus gel melting of the PEG‐PLA aqueous solutions occurs. The core‐rigidity of micelles must be one of the key factors in determining whether a polymer aqueous solution undergoes sol‐to‐gel or gel‐to‐sol transition, as the temperature increases. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, , 52, 2434–2441