Simple physical model for chemomechanics

We present a simple model linking chemical interactions with macroscopic mechanical deformations for polymer‐coated microcantilever devices. The chemo‐mechanical process is treated in terms of Fickian diffusion followed by a structural relaxation of the polymer‐guest complex. The model is tested on a series of microcantilever bending experiments, in the presence of different isotopologues, and at different incident guest fluxes. In many cases, a nontrivial behavior, expressed by the appearance of an overshoot, is observed. The new model provides insight into the ways chemical interactions and reorganization processes manifest themselves in mechanical processes. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys., 2013     

Nanomechanics of the formation of DNA self-assembled monolayers and hybridization on microcantilevers

Biomolecular interactions over the surface of a microcantilever can produce its bending motion via changes of the surface stress, which is referred to nanomechanical response. Here, we have studied the interaction forces responsible for the bending motion during the formation of a self-assembled monolayer of thiolated 27-mer single-stranded DNA on the gold-coated side of a microcantilever and during the subsequent hybridization with the complementary nucleic acid. The immobilization of the single-stranded DNA probe gives a mean surface stress of 25 mN/m and a mean bending of 23 nm for microcantilevers with a length and thickness of about 200 microm and 0.8 microm, respectively. The hybridization with the complementary sequence could not be inferred from the nanomechanical response. The nanomechanical response was compared with data from well-established techniques such as surface plasmon resonance and radiolabeling, to determine the surface coverage and study the intermolecular forces between neighboring DNA molecules anchored to the microcantilever surface. From both techniques, an immobilization surface density of 3 x 10(12) molecules/cm(2) and a hybridization efficiency of 40% were determined. More importantly, label-free hybridization was clearly detected in the same conditions with a conventional sensor based on surface plasmon resonance. The results imply that the nanomechanical signal during the immobilization process arises mainly from the covalent attachment to the gold surface, and the interchain interactions between neighboring DNA molecules are weak, producing an undetectable surface stress. We conclude that detection of nucleic acid hybridization with nanomechanical sensors requires reference cantilevers to remove nonspecific signals, more sensitive microcantilever geometries, and immobilization chemistries specially addressed to enhance the surface stress variations.     

Microcantilevers modified by horseradish peroxidase intercalated nano-assembly for hydrogen peroxide detection.

Detection of hydrogen peroxide is of industry interest and of biological importance. Here we report a new approach to hydrogen peroxide measurement using multilayer modified microcantilevers. Through a layer-by-layer nanoassembly technique, horseradish peroxidase was intercalated into a nanoscale multilayer assembly on one surface of microcantilevers. These enzyme-functionalized microcantilevers deflected in response to hydrogen peroxide concentrations in the nanomolar level. The magnitudes of bending were proportional to the concentrations of hydrogen peroxide. Furthermore, our study also showed that microcantilever technique may be used as a novel, more sensitive tool for the study of the conformational or structural changes of enzymes or proteins on surfaces.     

Towards a modular,versatile and portable sensor system for measurements in gaseous environments based on microcantilevers

Microfabricated silicon cantilever sensor arrays represent a powerful platform for sensing applications in physics, chemistry, material science, biology and medicine. The sensor response is mechanical bending due to absorption of molecules. In gaseous environment, polymer-coated microcantilevers are used as electronic nose for characterization of vapors, resulting in cantilever bending due to polymer swelling upon exposure. Medical applications involve fast characterization of exhaled patient's breath samples for detection of diseases, based on the presence of certain chemicals in breath. We present a portable, compact, modular microcantilever setup, which uses a micropump for aspiration and a bluetooth interface for remote data acquisition.     

Photochemical hydrosilylation of 11-undecenyltriethylammonium bromide with hydrogen-terminated Si surfaces for the development of robust microcantilever sensors for Cr(VI)

We report a novel approach to the design and development of microcantilever sensors in which photochemical hydrosilylation is used to modify the microcantilever surface. This process enables individual microcantilevers in multicantilever array chips to be modified separately by focusing the activating UV light sequentially on each particular cantilever. Photochemical hydrosilylation of 11-undecenyltriethylammonium bromide with hydrogen-terminated silicon microcantilever surfaces was carried out to yield a robust quaternary ammonium terminated organic monolayer suitable for chromate detection. The surface functionalities retain their affinity toward Cr(VI), and the organic monolayer is dense enough to generate significant surface stress upon subsequent adsorption of chromate ions from aqueous solutions.     

Morphology‐Dependent Gas‐Sensing Properties of ZnO Nanostructures for Chlorophenol

The crystal‐plane effect of ZnO nanostructures on the toxic 2‐chlorophenol gas‐sensing properties was examined. Three kinds of single‐crystalline ZnO nanostructures including nanoawls, nanorods, and nanodisks were synthesized by using different capping agents via simple hydrothermal routes. Different crystal surfaces were expected for these ZnO nanostructures. The sensing tests results showed that ZnO nanodisks exhibited the greatest sensitivity for the detection of toxic 2‐chlorophenol. The results revealed that the sensitivity of these ZnO samples was heavily dependent on their exposed surfaces. The polar (0001) planes were most reactive and could be considered as the critical factor for the gas‐sensing performance. In addition, calculations using density functional theory were employed to simulate the gas‐sensing reaction involving surface reconstruction and charge transfer both of which result in the change of electronic conductance of ZnO.     

Highly Selective “Turn‐On” Fluorescent and Colorimetric Sensing of Fluoride Ion Using 2‐(2‐Hydroxyphenyl)‐2,3‐dihydroquinolin‐4(1 H)‐one based on Excited‐State Proton Transfer

A simple, highly selective and sensitive colorimetric system for the detection of fluoride ion in an aqueous medium has been developed using 2‐(2‐hydroxyphenyl)‐2,3‐dihydroquinolin‐4(1 H)‐one. This system allows selective “turn‐on” fluorescence detection of fluoride ion, which is found to be dependent upon guest basicity. An excited‐state proton transfer is proposed to be the signaling mechanism, which is rationalized by DFT and TD‐DFT calculations. The present sensor can also be applied to detect fluoride levels in real water samples.     

A TD‐DFT study on the cyanide‐chemosensing mechanism of 8‐formyl‐7‐hydroxycoumarin

Proton transfer (PT) and excited‐state PT process are proposed to account for the fluorescent sensing mechanism of a cyanide chemosensor, 8‐formyl‐7‐hydroxycoumarin. The time‐dependent density functional theory method has been applied to investigate the ground and the first singlet excited electronic states of this chemosensor as well as its nucleophilic addition product with cyanide, with a view to monitoring their geometries and spectrophotometrical properties. The present theoretical study indicates that phenol proton of the chemosensor transfers to the formyl group along the intramolecular hydrogen bond in the first singlet excited state. Correspondingly, the nucleophilic addition product undergoes a PT process in the ground state, and shows a similar structure in the first singlet excited state. This could explain the observed strong fluorescence upon the addition of the cyanide anion in the relevant fluorescent sensing mechanism. © 2010 Wiley Periodicals, Inc. J Comput Chem, 2011     

Sequence‐Dependent Self‐Assembly of Chiral Polyimides

Sequence‐defined chiral polyimides comprising identical asymmetric diamine monomers arranged in different directions along the main chain were designed and prepared. These new sequence‐defined polymers exhibit sequence‐dependent self‐assembly behaviors and responses to ibuprofen enantiomers, as revealed by their chiroptical spectra and gelation properties. For the first time, the self‐assembly of polymers and their interactions with guest molecules have been successfully controlled by means of the directional arrangement of the monomers in their polymer backbones.     

Electrospray‐Ionization Mass Spectrometry for Screening the Specificity and Stability of Single‐Stranded‐DNA Templated Self‐Assemblies

Supramolecular complexes consisting of a single‐stranded oligothymine ( dTn ) as the host template and an array of guest molecules equipped with a complementary diaminotriazine hydrogen‐bonding unit have been studied with electrospray‐ionization mass spectrometry (ESI‐MS). In this hybrid construct, a supramolecular stack of guest molecules is hydrogen bonded to dTn . By changing the hydrogen‐bonding motif of the DNA host template or the guest molecules, selective hydrogen bonding was proven. We were able to detect single‐stranded‐DNA (ssDNA)–guest complexes for strands with lengths of up to 20 bases, in which the highest complex mass detected was 15 kDa; these complexes constitute 20‐component self‐assembled objects. Gas‐phase breakdown experiments on single‐ and multiple‐guest–DNA assemblies gave qualitative information on the fragmentation pathways and the relative complex stabilities. We found that the guest molecules are removed from the template one by one in a highly controlled way. The stabilities of the complexes depend mainly on the molecular weight of the guest molecules, a fact suggesting that the complexes collapse in the gas phase. By mixing two different guests with the ssDNA template, a multicomponent dynamic library can be created. Our results demonstrate that ESI‐MS is a powerful tool to analyze supramolecular ssDNA complexes in great detail.     

Measurements of interface stress of silicon dioxide in contact with water-phenol mixtures by bending of microcantilevers

We use the bending of silicon microcantilevers to measure changes in mechanical stress at interfaces between phenol-water mixtures and SiO(2). The curvature of the microcantilever is measured by an optical system that combines a rapidly scanning laser beam, a position-sensitive detector, and lock-in detection to achieve a long-time stability on the order of 6 mN m(-1) over 4 h and a short-time sensitivity of better than 1 mN m(-1). Thermally oxidized Si shows the smallest changes in interface stress as a function of phenol concentration in water. For hydrophilic SiO(2) prepared by chemical treatment, the change in interface stress at 5 wt % phenol in water is larger than that of thermally oxidized Si by -60 mN m(-1); for SiO(2) formed by exposure of the silicon microcantilever to ozone, the change in surface stress is larger than that of thermally oxidized Si by -330 mN m(-1).     

Transient deflection response in microcantilever array integrated with polydimethylsiloxane (PDMS) microfluidics

We report the integration of a nanomechanical sensor consisting of 16 silicon microcantilevers with polydimethylsiloxane (PDMS) microfluidics. For microcantilevers positioned near the bottom of a microfluidic flow channel, a transient differential analyte concentration for the top versus bottom surface of each microcantilever is created when an analyte-bearing fluid is introduced into the flow channel (which is initially filled with a non-analyte containing solution). We use this effect to characterize a bare (nonfunctionalized) microcantilever array in which the microcantilevers are simultaneously read out with our recently developed high sensitivity in-plane photonic transduction method. We first examine the case of non-specific binding of bovine serum albumin (BSA) to silicon. The average maximum transient microcantilever deflection in the array is -1.6 nm, which corresponds to a differential surface stress of only -0.23 mN m(-1). This is in excellent agreement with the maximum differential surface stress calculated based on a modified rate equation in conjunction with finite element simulation. Following BSA adsorption, buffer solutions with different pH are introduced to further study microcantilever array transient response. Deflections of 20-100 nm are observed (2-14 mN m(-1) differential surface stress). At a flow rate of 5 μL min(-1), the average measured temporal width (FWHM) of the transient response is 5.3 s for BSA non-specific binding and 0.74 s for pH changes.     

A Red‐Emissive Sextuple Hydrogen‐Bonding Self‐Assembly Molecular Duplex Bearing Perylene Diimide Fluorophores for Warm‐White Organic Light‐Emitting Diode Application

A novel sextuple hydrogen‐bonding (HB) self‐assembly molecular duplex bearing red‐emitting perylene diimide (PDI) fluorophores, namely PDIHB , was synthesized, and its molecular structure was confirmed by ¹H NMR, ¹³C NMR, TOF‐MS and 2D NMR. Compared with the small molecular reference compound PDI , PDIHB shows one time enhanced fluorescence efficiency in solid state (4.1% vs. 2.1%). More importantly, the presence of bulky HB oligoamide strands in PDIHB could trigger effective spatial separation between guest and host fluorophores in thin solid film state, hence inefficient energy transfer occurs between the blue‐emitting host 2TPhNIHB and red guest PDIHB in the 2 wt% guest/host blending film. As a result, a solution‐processed organic light‐emitting diode (OLED) with quite simple device structure of ITO/PEDOT:PSS (40 nm)/PVK (40 nm)/ PDIHB (2 wt%): 2TPhNIHB (50 nm)/LiF (0.8 nm)/Al (100 nm) could emit bias‐independent warm‐white electroluminescence with stable Commission Internationale de L'Eclairage coordinates of (0.42, 0.33), and the maximum brightness and current efficiency of this device are 260 cd·m^?2 and 0.49 cd·A^?1, respectively. All these results indicated that HB self‐assembly supramolecular fluorophores could act as prospective materials for white OLED application.     

Improved surface modification approach for micromechanical biosensors

We have investigated the sensing performance of protein-based microcantilever biosensors prepared from multiple surface conjugation chemistries. The 11-mercaptoundecanoic acid monolayers were prepared according to both traditional and modified processes. In three protein-based biosensors, the modified process improved microcantilever sensing performance by increasing the bending amplitude, a critical step toward developing a cost-effective microcantilever-based sensor platform for medical diagnostics and environmental and drug screening applications. Scanning electron microscopy (SEM) images demonstrated that proteins immobilized on the microcantilever surface using the modified chemistry approach formed a compact layer.     

A Host‐Guest‐Recognition‐Based Electrochemical Sensor for Sequence‐Specific DNA Detection

We herein constructed a sensor that converts target DNA hybridization‐induced conformational transformation of the probe DNA to electrochemical response based on host‐guest recognition and nanoparticle label. In the sensor, the hairpin DNA terminal‐labeled with 4‐((4‐(dimethylamino)phenyl)azo)benzoic acid (dabcyl) and thiol group was immobilized on Au electrode surface as the probe DNA by Au‐S bond, and the CdS nanoparticles surface‐modified with β‐cyclodextrins (CdS‐CDs) were employed as electrochemical signal provider and host‐guest recognition element. Initially, the probe DNA immobilized on electrode kept the stem‐loop configuration, which shielded dabcyl from docking with the CdS‐CDs in solution due to the steric effect. After target hybridization, the probe DNA underwent a significant conformational change, which forced dabcyl away from the electrode. As a result, formerly‐shielded dabcyl became accessible to host‐guest recognition between β‐cyclodextrin (β‐CD) and dabcyl, thus the target hybridization event could be sensitively transduced to electrochemical signal provided by CdS‐CDs. This host‐guest recognition‐based electrochemical sensor has been able to detect as low as picomolar DNA target with excellent differentiation ability for even single mismatch.     

Durable ultra‐hydrophobic surfaces for self‐cleaning applications

Self‐cleaning surfaces have received a great deal of attention, both in research studies and commercial applications. Both transparent and non‐transparent self‐cleaning surfaces are highly desirable as they offer many advantages, and their potential applications are endless. The self‐cleaning mechanism can be seen in nature. The Lotus flower, a symbol of purity in Asian cultures, grows in muddy waters, but it stays clean and untouched by dirt, organisms, and pollutants. The Lotus leaf self‐cleaning surface is hydrophobic and rough, showing a multi‐layer morphology of nanoscaled roughness. While hydrophobicity produces a high contact angle, the surface morphology reduces the adhesion of water drops to the surface, which slides easily across the leaf surface carrying the dirt particles with them. Different ultra‐hydrophobic, non‐transparent, and transparent coatings, for potential self‐cleaning applications, were produced on polycarbonate (PC) substrates, using hydrophobic chemistry and different configurations of roughening micro‐ and nano‐particles. However, in most cases, these coatings present low adhesion and durability. The stability and durability of the ultra‐hydrophobic surfaces is of key importance for potential, commercially viable, self‐cleaning applications thus durability and stability enhancement of such coatings was attempted by different methods, evaluated, and eventually improved using a solvent‐bonding technique. Copyright © 2008 John Wiley & Sons, Ltd.     

Spatially Controlled Out‐of‐Equilibrium Host–Guest System under Electrochemical Control

Self‐assembly to create molecular and nanostructures is typically performed at the thermodynamic minimum. To achieve dynamic functionalities, such as adaptability, internal feedback, and self‐replication, there is a growing focus on out‐of‐equilibrium systems. This report presents the dynamic self‐assembly of an artificial host–guest system at an interface, under control by a dissipative electrochemical process using (electrical) energy, resulting in an out‐of‐equilibrium system exhibiting a supramolecular surface gradient. The gradient, its steepness, rate of formation, and complex surface composition after backfilling, as well as the surface compositions after switching between the different states of the system, are assessed and supported by modelling. Our method shows for the first time an artificial surface‐confined out‐of‐equilibrium system. The electrochemical process parameters provide not only control over the system in time, but also in space.     

Optical Sensing of Current Dynamics in Organic Light‐Emitting Devices at the Nanometer Scale

Photoluminescence quenching of single dibenzoterrylene (DBT) dye molecules in a polymeric organic light‐emitting diode was utilized to analyze the current dynamics at nanometer resolution. The quenching mechanism of single DBT molecules results from an increase in the triplet‐state population induced by charge carrier recombination on individual guest molecules. As a consequence of the long triplet‐state relaxation time, its population results in a reduced photoluminescence of the dispersed fluorescent dyes. From the decrease in photoluminescence together with photon correlation measurements, we could quantify the local current density and its time‐dependent evolution in the vicinity of the single‐molecule probe. This optical technique establishes a non‐invasive approach to map the time‐resolved current density in organic light‐emitting diodes on the nanometer scale.     

Macroscopic Responsive Liquid Quantum Dots Constructed via Pillar[5]arene‐Based Host‐Guest Interactions

Liquid quantum dots (QDs) have been used as a fluorescent films sensor. Constructing a macroscopic, responsive, liquid QD system for lysine (Lys) is a challenging task. To achieve a selective macroscopic response towards Lys, herein we present a new strategy for integrating host–guest chemistry into a liquid QD system. Water‐soluble pillar[5]arene WP5 was designed and synthesized as a host. WP5 was introduced onto the surface of PEG1810‐modified QDs by host–guest interactions to obtain liquid WP5‐1810‐QDs. The interaction between WP5 and Lys is stronger than that between WP5 and PEG‐1810, causing WP5 to be released from the 1810‐QDs surface in the presence of Lys, resulting in macroscopic fluorescence quenching. This smart material shows promise in amino acid sensing and separation.     

High sensitivity of diamond resonant microcantilevers for direct detection in liquids as probed by molecular electrostatic surface interactions

Resonant microcantilevers have demonstrated that they can play an important role in the detection of chemical and biological agents. Molecular interactions with target species on the mechanical microtransducers surface generally induce a change of the beam's bending stiffness, resulting in a shift of the resonance frequency. In most biochemical sensor applications, cantilevers must operate in liquid, even though damping deteriorates the vibrational performances of the transducers. Here we focus on diamond-based microcantilevers since their transducing properties surpass those of other materials. In fact, among a wide range of remarkable features, diamond possesses exceptional mechanical properties enabling the fabrication of cantilever beams with higher resonant frequencies and Q-factors than when made from other conventional materials. Therefore, they appear as one of the top-ranked materials for designing cantilevers operating in liquid media. In this study, we evaluate the resonator sensitivity performances of our diamond microcantilevers using grafted carboxylated alkyl chains as a tool to investigate the subtle changes of surface stiffness as induced by electrostatic interactions. Here, caproic acid was immobilized on the hydrogen-terminated surface of resonant polycrystalline diamond cantilevers using a novel one-step grafting technique that could be also adapted to several other functionalizations. By varying the pH of the solution one could tune the -COO(-)/-COOH ratio of carboxylic acid moieties immobilized on the surface, thus enabling fine variations of the surface stress. We were able to probe the cantilevers resonance frequency evolution and correlate it with the ratio of -COO(-)/-COOH terminations on the functionalized diamond surface and consequently the evolution of the electrostatic potential over the cantilever surface. The approach successfully enabled one to probe variations in cantilevers bending stiffness from several tens to hundreds of millinewtons/meter, thus opening the way for diamond microcantilevers to direct sensing applications in liquids. The evolution of the diamond surface chemistry was also investigated using X-ray photoelectron spectroscopy.