Stopped-flow spectrophotometric determination of hydrogen peroxide with hemoglobin as catalyst

A rapid and sensitive method was proposed for the determination of hydrogen peroxide based on the catalytic effect of hemoglobin using o-phenylenediamine as the substrate. Stopped-flow spectrophotometric method was used to study the kinetic behavior of the oxidation reaction. The catalytic effectiveness of hemoglobin was compared with other four kinds of catalysts. The initial rate of the formation of the reaction product 2,3-diaminophenazine at the wavelength of 425 nm was monitored, permitting a detection limit of 9.2x10(-9) mol/l H(2)O(2). A linear calibration graph was obtained over the H(2)O(2) concentration range 5.0x10(-8)-3.5x10(-6) mol/l, and the relative standard deviation at a H(2)O(2) concentration of 5.0x10(-7) mol/l was 2.08%. Satisfied results were obtained in the determination of H(2)O(2) in real samples by this method.     

Unusual efficiency of a non-heme iron complex as catalyst for the hydroxylation of aromatic compounds by hydrogen peroxide: comparison with iron porphyrins

The non-heme iron complex, Fe(TPAA = tris-〚N-(2-pyridylmethyl)-2-aminoethyl〛amine)(ClO₄)₂, is a bad catalyst for the epoxidation of alkenes such as cyclooctene, cyclohexene and cis-stilbene and for the hydroxylation of alkanes such as adamantane by H₂O₂, when compared to the iron porphyrin Fe〚TDCPN₅P = meso-tetra-(2,6-dichlorophenyl)-β-pentanitroporphyrin〛Cl. At the opposite, Fe(TPAA)(ClO₄)₂ is a much better catalyst for the hydroxylation of arenes by H₂O₂; in its presence, anisole, toluene, ethylbenzene, benzene and chlorobenzene are transformed into the corresponding phenols, with respective yields of 53, 17, 24, 22 and 13% based on H₂O₂. Interestingly, in Fe(TPAA)-catalysed oxidations of anisole, toluene and ethylbenzene by H₂O₂, hydroxylation of the aromatic ring is by far the major reaction, even when compared to usually favoured reactions such as benzylic oxidation and oxidative demethylation.     

A chiral iron-sexipyridine complex as a catalyst for alkene epoxidation with hydrogen peroxide

A chiral iron-sexipyridine complex-hydrogen peroxide mixture is a highly efficient catalytic system for styrene epoxidation with excellent reactivity (3 min, 95% yield) and chemoselectivity (98%).     

Formic acid as a reagent for alkaline permanganate : Potentiometric determination of formate

Oxidation of formate with permanganate in alkaline solutions yields a mixture of MnO₄^-2 and MnO₂. The reaction occurs slowly without an abrupt change in potential at the end-point. In 0.1N NaOH, at 80° C in the presence ofAg⁺ions or NaCl,the reaction is accelerated and yields MnO₂. The concentrations of formic acid obtained by oxidation with permanganate are comparable with those obtained by neutralization down to 2.295·10^-2N.Reduction of permanganate in the presence of Ba⁺² ions (alkalinity = 0.5 — 1.5N) or in the absence of Ba⁺ ions (alkalinity = 0.5 — 2.5N), gave accurate results for the permanganate concentration comparable with the results of the acid oxalate method.Formic acid is preferred to sodium formate on account of the greater stability of its solutions.     

Oxidations with potassium permanganate in the presence of fluoride

Summary Trivalent chromium and quadrivalent vanadium can be determined with fair accuracy by a method consisting in mixing either with an excess of KMnO₄ in the presence of 0.3 to 1.8 M alkali hydroxide. After leaving the mixture for 5 min, the solution is acidified with sulphuric acid and mixed with 50 to 75 ml of 2% NaF solution. An excess of monovalent mercury Hg₂ ²⁺ solution is then added, the solution heated to 40° C and then titrated with KMnO₄ solution in the presence of Cu²⁺ ions to conceal the pink manganic fluoride colour.Part II: Issa, I. M., and M. Hamdy: Z. analyt. Chem. 172, 162 (1960).     

Oxidations with potassium permanganate in the presence of fluoride

Summary The titration of ferrous iron in presence of fluoride ions in acid medium gives fleeting end points and erroneous results. A method is deviced to overcome this difficulty by oxidising the ferrous with an excess of KMnO₄ in alkaline medium. After mixing the reactants the excess of KMnO₄ is reduced by an excess of Hg₂ ²⁺ ions in presence of H₂SO₄ and fluoride. The remaining mercurous is then titrated with standard KMnO₄ solution.Part III: Issa, I. M., and M. Hamdy: Z. analyt. Chem. 174, 418 (1960).     

Oxidations with potassium permanganate in the presence of fluoride

Summary Quadrivalent selenium can be determined with fair accuracy by mixing with an excess of KMnO₄ in the presence of 25–75 ml of 2% NaF solution and 4–7 ml of 9 N sulfuric acid. After leaving the reaction mixture for 10–30 minutes the excess KMnO₄ is estimated by one of the following procedures: A) Titration of the excess KMnO₄ with monovalent mercury, B) Adding an excess of Hg₂ ²⁺ solution to react with the excess KMnO₄ followed by titrating the excess mercurous with KMnO₄ solution.Part I: Issa, I. M., and M. Hamdy, Z. analyt. Chem. 172, 94 (1980).     

Potentiometric determination of iron with DTPA in the presence of a large amount of aluminium

Potentiometric determination of iron with DTPA at pH 1.6 (platinum and calomel electrodes) permits determination of iron in the presence of aluminium up to an Al:Fe ratio of 70. Aluminium is determined indirectly by addition of excess of DCTA, adjustment to pH 5, and back-titration with iron(III) chloride.     

Oxidation with permanganate in presence of fluoride potentiometric determination of manganese(II)

The effects of acidity, fluoride concentration, temperature and concentration of manganese in the reaction between KMnO(4) and Mn(II) were studied potentiometrically. The rate of reaction is increased by increasing the fluoride concentration and/or decreasing the acidity of the solution. The formal redox potentials of the MnO(-)(4)/Mn(III) and the Mn(III)/Mn(II) systems were determined at different pH values. The E degrees values obtained by extrapolation to pH = 0 were 1.58 and 1.52 V respectively. The amount of Mn(II) determined was varied from 5 to 56 mg. The net reaction can be represented as MnO(-)(4) + 10HF(-)(2) + 4Mn(2+) right harpoon over left harpoon 5MnF(-)(4) + 2H(+) + 4H(2)O.     

Catalase biosensor for the determination of hydrogen peroxide,fluoride and cyanide

The enzyme catalase, which catalyses the decomposition of hydrogen peroxide to oxygen and water, was immobilized in a membrane by entrapping it in polyacryl amide and contacted to a Clark-type oxygen electrode. With the resulting catalase biosensor it was possible to detect the substrate hydrogen peroxide and the inhibitors fluoride and cyanide in phosphate buffer.The sensor was integrated into a flow system. In the concentration range from 5–200 mg/l a linear dependence of the peak height on the hydrogen peroxide concentration was obtained. The average decrease in activity during 30 days of storage at 6 °C was 17%. Fluoride and cyanide could be determined by measuring the inhibition of the enzymatic reaction in the same flow system. The analysis was executed in three steps; namely determination of the original activity by pumping substrate solution, inhibition of the enzyme by pumping inhibitor solution, and determination of the activity after the inhibition.The decrease in activity correlated with the inhibitor concentration of the sample, but a linear dependence was not found. The inhibition of fluoride and cyanide was both reversible, the enzyme membrane could be reactivated completely by pumping substrate solution. The detection limit was 1 mg/l for fluoride and 1.5 mg/l for cyanide.     

Reaction of hydrogen peroxide with tetraazamacrocyclic complex of iron(II) in the presence of nitrogeneous bases

The kinetics of hydrogen peroxide oxidation of Fe(II) to Fe(III) complexed with tetraazamacrocyclic ligand was studied, and a decrease in the reaction rate was observed in the presence of nitrogeneous bases, capable of forming hexacoordinated complexes with tetraazamacrocyclic compound of iron(II). The rate of reaction is proprotional to the concentration of the iron complex and hydrogen peroxide and inversely proportional to the concentration of the nitrogeneous base. A mechanism for the course of the reaction has been proposed, and the rate constants of the oxidation of the pentacoordinated iron(II) complexes have been calculated. It was shown that the addition of the fifth donor particle (in particular imidazole) activates the iron(II) atom with respect to the oxidation reaction. It was found that a tetraazamacrocyclic complex of iron(II) is capable of displaying a peroxidase type activity.Translated from Teoreticheskaya Eksperimental'naya Khimiya, Vol. 22, No. 3, pp. 309–316, May–June, 1986.     

Oxidation with permanganate in presence of fluoride: Determination of hypophosphite

A rapid method is described for the determination of hypophosphite by oxidation with permanganate in acid medium in the presence of fluoride to prevent formation of insoluble oxides of manganese. The optimum conditions for visual and potentiometric end-point detection are given. Hypophosphite is oxidized to H(2)PO(-)(3). Under optimum conditions the titrations are fast and exhibit a reasonable potential change at the end-point. The method demonstrates the feasibility of determining amounts of H(2)PO(-)(2) corresponding to 0.08-7 mg of phosphorus.     

Highly sensitive spectrophotometric determination of cobalt using o-hydroxyhydroquinonephthalein and hydrogen peroxide in the presence of mixed surfactants

Summary The effects of cobalt(II) and surfactants on the decomposition of various xanthene dyes by hydrogen peroxide have been systematically investigated. A simple and highly sensitive spectrophotometric determination of cobalt(II) (0.05 1.2 g/10 ml) is proposed. The method is based on the catalytic effect of cobalt(II) on the oxidation of o-hydroxyhydroquinonephthalein (Qnph) by hydrogen peroxide. The proposed catalytic spectrophotometric determination was sensitive, selective, reproducible and virtually unaffected by the presence of other ions; the effective molar desorptivity was 4.2×10⁸ l/mol per cm, Sandell sensitivity was 0.15 pg/cm², and the relative standard deviation was 3.2% at 0.6 ng/10 ml (n=5). The selective assays of cobalt(II) in water samples were also investigated with satisfactory results (95% 101%).

---

Hochempfindliche Spektralphotometrische Kobaltbestimmung mit Hilfe von o-Hydroxyhydrochinonphthalein und Wasserstoffperoxid in Gegenwart von oberflÄchenaktiven Substanzen

---

Application of xanthene derivatives in analytical chemistry. Part LXIX. Part LXVIII see ref. [1]     

Porphyrin hybrid complex ([2Fe-2S]2TPPS) as a catalyst for determination of hydrogen peroxide.

A new promising mimetic enzyme, a [2Fe-2S] cluster-porphyrin hybrid complex ([2Fe-2S]2TPPS), has been synthesized and applied to the determination of hydrogen peroxide. Under the optimum condition, the calibration graph has a linear range of 8.0 x 10(-8) - 1.0 x 10(6) mol/l H2O2 with a detection limit (3sigma, N = 9) of 5.3 x 10(-9) mol/l.     

Fluorometric method for the determination of hydrogen peroxide and glucose with Fe3O4 as catalyst

In this paper, we utilized the instinct peroxidase-like property of Fe₃O₄ magnetic nanoparticles (MNPs) to establish a new fluorometric method for determination of hydrogen peroxide and glucose. In the presence of Fe₃O₄ MNPs as peroxidase mimetic catalyst, H₂O₂ was decomposed into radical that could quench the fluorescence of CdTe QDs more efficiently and rapidly. Then the oxidization of glucose by glucose oxidase was coupled with the fluorescence quenching of CdTe QDs by H₂O₂ producer with Fe₃O₄ MNPs catalyst, which can be used to detect glucose. Under the optimal reaction conditions, a linear correlation was established between fluorescence intensity ratio I₀/I and concentration of H₂O₂ from 1.8 × 10⁻⁷ to 9 × 10⁻⁴ mol/L with a detection limit of 1.8 × 10⁻⁸ mol/L. And a linear correlation was established between fluorescence intensity ratio I₀/I and concentration of glucose from 1.6 × 10⁻⁶ to 1.6 × 10⁻⁴ mol/L with a detection limit of 1.0 × 10⁻⁶ mol/L. The proposed method was applied to the determination of glucose in human serum samples with satisfactory results.     

Extraction and spectrophotometric determination of iron as o-phenanthroline-azide mixed ligand complex

Summary The mixed ligand complex, [Fe(Phen)₂(N₃)₂] can be extracted into nitrobenzene giving a molar absorptivity of 16750 at 510 nm. This is the basis of a photometric method for iron which may be either in the trivalent or bivalent state. The new method is free from interference from a number of substances and is more sensitive than the ferroin method.

---

Zusammenfassung Der Eisen-Phenanthrolin-Azid-Mischkomplex [Fe(Phen)₂(N₃)₂] ist mit Nitrobenzol extrahierbar und gibt bei 510 nm eine molare Absorption von 16750. Darauf läßt sich eine photometrische Bestimmungsmethode für zweioder dreiwertiges Eisen begründen. Diese wird von vielen Stoffen nicht gestört und ist empfindlicher als die Ferroinmethode.

     

Selective spectrophotometric determination of vanadium in silicates with a new pyridylazophenol in the presence of hydrogen peroxide

The synthesis of a new heterocyclic azo compound, 2-(3,5-dibromo-4-methyl-2-pyridylazo)-5-diethylaminophcnol (3,5-Br-MEPADAP is described. The dye forms an intensely coloured (ε=4.11·10⁴ 1 mole^-1 cm^-1 at 615 nm) unstable chelate with vanadium(V) in weakly acidic medium. However, vanadium(V) reacts with 3,5-Br-MEPADAP and hydrogen peroxide in 0.5 M sulphuric acid to form a stable 1:1:1 ternary complex which is extractable in several solvents. In the presence of fluoride, the reaction is highly selective for vanadium(V); only large amounts of halides, oxidizing and reducing agents interfere. The effective molar absorptivity is 5.43 ·10⁴ 1 mole^-1 cm^-1 at 615 nm in chloroform. The reagent system was applied for the direct spectrophotometric determination of vanadium in a wide range of silicates; the average relative standard deviation was 0.45 %. The accuracy of the vanadium values obtained for ten international standard rocks compares well with the currently accepted most probable values.     

Oxidation with permanganate in acid medium containing fluoride: determination of bisulphite

The factors affecting the success of both visual and potentiometric end-point detection in titration of bisulphite with permanganate in the presence of fluoride are examined. The optimum conditions are 0.02M H(2)SO(4) and 0.24-0.38M NaF. The oxidation product comprises dithionate and sulphate according to the overall reaction MnO(4)(-) + H(+) + 2HF(2)(-) + 3HSO(3)(-) right harpoon over left harpoon MnF(4)(-) + S(2)O(6)(2-) + SO(4)(2-) + 3H(2)O. The reverse titration is also satisfactory, but proceeds quantitatively according to MnO(4)(2-) + 2HF(2)(-) + 2HSO(3)(-) right harpoon over left harpoon MnF(4)(-) + 2SO(4)(2-) + 2H(2)O.