Hierarchically Annular Mesoporous Carbon Derived from Phenolic Resin for Efficient Removal of Antibiotics in Wastewater

Antibiotics have become a new type of environmental pollutant due to their extensive use. High-performance adsorbents are of paramount significance for a cost-effective and environmentally friendly strategy to remove antibiotics from water environments. Herein, we report a novel annular mesoporous carbon (MCN), prepared by phenolic resin and triblock copolymer F127, as a high-performance adsorbent to remove penicillin, streptomycin, and tetracycline hydrochloride from wastewater. The MCNs have high purity, rich annular mesoporosity, a high surface area (605.53 m²/g), and large pore volume (0.58 cm³/g), improving the adsorption capacity and facilitating the efficient removal of penicillin, streptomycin, and tetracycline hydrochloride from water. In the application of MCNs to treat these three kinds of residual antibiotics, the adsorption amounts of tetracycline hydrochloride were higher than penicillin and streptomycin, and the adsorption capacity was up to 880.6 mg/g. Moreover, high removal efficiency (99.6%) and excellent recyclability were achieved. The results demonstrate that MCN adsorbents have significant potential in the treatment of water contaminated with antibiotics.     

New Composite Sorbent for Removal of Sulfate Ions from Simulated and Real Groundwater in the Batch and Continuous Tests

The evaluation of groundwater quality in the Dammam formation, Faddak farm, Karbala Governorate, Iraq proved that the sulfate (SO₄²⁻) concentrations have high values; so, this water is not suitable for livestock, poultry and irrigation purposes. For reclamation of this water, manufacturing of new sorbent for permeable reactive barrier was required through precipitation of Mg and Fe hydroxides nanoparticles on the activated carbon (AC) surface with best Mg/Fe molar ratio of 7.5/2.5. Mixture of 50% coated AC and 50% scrap iron was applied to eliminate SO₄²⁻ from contaminated water with efficiency of 59% and maximum capacity of adsorption equals to 9.5 mg/g for a time period of 1 h, sorbent dosage 40 g/L, and initial pH = 5 at 50 mg/L initial SO₄²⁻ concentration and 200 rpm shaking speed. Characterization analyses certified that the plantation of Mg and Fe nanoparticles onto AC was achieved. Continuous tests showed that the longevity of composite sorbent is increased with thicker bed and lower influent concentration and flow rate. Computer solution (COMSOL) software was well simulated for continuous measurements. The reclamation of real contaminated groundwater was achieved in column set-up with efficiency of 70% when flow rate was 5 mL/min, bed depth was 50 cm and inlet SO₄²⁻ concentration was 2301 mg/L.     

Activation of sulfite by ferric ion for the degradation of 2,4,6-tribromophenol with the addition of sulfite in batches

In this work, the removal of 2,4,6-tribromophenol (TBP) by ferric ion-activated sulfite [Fe(III)/S(IV)] process was systematically investigated with determining the intermediate products and evaluating the influences of some operational conditions and water matrices. Our results show that batching addition of S(IV) benefits the S(IV) utilization efficiency and TBP removal, with SO₄^?? being the primary reactive radical accounting for TBA degradation. The maximum TBP removal in the Fe(III)/S(IV) process was observed at pH 4.0 and oxygen is essential in this process. With increasing Fe(III) and S(IV) dosages from 0.05 and 0.1 mmol/L to 0.2 and 2.0 mmol/L, respectively, TBP removal followed trends of first increase then decrease. As the acute toxicity of the TBP solution was significantly reduced, the Fe(III)/S(IV) process was believed to be a good choice in the treatment of TBP.     

Electrospun metal‐organic framework/polyacrylonitrile composite nanofibrous mat as a microsorbent for the extraction of tetracycline residue in human blood plasma

A new composite nanofiber of polyacrylonitrile doped with copper benzene‐1,3,5‐tricarboxylate metal‐organic framework was fabricated by electrospinning and used as a microsorbent in the solid‐phase extraction of trace tetracycline. The chemical structure of the adsorbent was studied by X‐ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, Brunauer–Emmett–Teller surface area analysis, and Barrett‐Joyner‐Halenda pore size and volume analysis techniques. The significant parameters of the method including desorption solvent kind and volume, adsorbent mass, pH, and salt percentage were investigated. At the optimized conditions, the linear range was 8–1000 μg/L with a determination coefficient (R²) of 0.9954. The limits of detection and quantification were 2.40 and 8.00 μg/L, respectively. The inter‐ and intraday precisions were 4.7 and 3.4%, respectively. The developed extraction method was followed by high‐performance liquid chromatography and applied for the determination of tetracycline in human blood plasma, and good relative recoveries (97.3‐104.5%) were obtained.     

Preparation of γ-Al2O3 sorbents loaded with metal components and removal of thiophene from coking benzene

Series sorbents of Cu, Zn, Ni, Ce and Ag metal components supported on γ-Al₂O₃ carrier for removing thiophene from benzene were prepared by conventional and ultrasound-assisted incipient-wetness impregnation method. The static adsorption experiments were carried out in the thiophene-benzene solution with thiophene concentration of 500?mg/L. The results show that the desulfurization activity of all γ-Al₂O₃ sorbents modified by different metal components obviously increase, among which the sorbent modified by silver nitrate has the best performance. The active components of sorbents from Cu, Zn, Ni, Ce nitrates loaded on γ-Al₂O₃ carrier are their oxides. Besides Ag₂O, the products of silver nitrate thermal decomposition in sorbent prepared still have Ag⁰ and Ag–O–Al species. The assistant ultrasound in the process of sorbent preparation can not only shorten the impregnation time, but also enrich the pore structure of sorbent and improve the size and distribution of the Ag species, which is favorable to the removal of thiophene from benzene. The desulfurization capacity of sorbent changes with the Ag content loaded. The sorbent with 15?% quality content of Ag prepared by ultrasound-assisted impregnation method has the highest desulfurization efficiency. It could reduce the thiophene concentration to 1.7?mg/L from 500?mg/L at room temperature and ambient pressure, with the desulfurization efficiency of more than 99?%, when the ratio of sorbent to solution was 1:4?(g/mL).     

Relevance in the Fischer-Tropsch synthesis of the formation of Fe-O-Ce interactions on iron-cerium mixed oxide systems

A series of Fe-Ce mixed oxides (95 atom % Fe-5 atom % Ce) has been prepared by different methods: coprecipitation, impregnation, and physical mixture of Ce and Fe oxides. These solids have been tested in the Fischer-Tropsch synthesis. The characterization of the catalytic precursors was carried out by X-ray diffraction (XRD), Raman, M?ssbauer, and X-ray photoelectron (XPS) spectroscopic techniques. When the preparation method ensures a microscopic contact between Fe and Ce cations in the solid, several types of Fe-Ce interactions are present in the calcined solids. The interactions take the shape of Fe-O-Ce bridges that can exist either in the hematite-like solid solution or in the interphase between the Fe oxide covered by microcrystals of Ce oxide. In the case of the hematite-like solid solution, Ce(IV) cations are dissolved in the alpha-Fe2O3 network. The promotion by Ce of the catalytic properties observed in the final catalysts can be directly related with the detection of these Fe-O-Ce bridges in the calcined solids. The Ce promotion results in a larger yield to hydrocarbons, a higher production of olefins, and a higher selectivity to medium and large chain hydrocarbons (larger than six carbon atoms). It is proposed that the Ce promotion is due to the presence of Fe0-Ce(III) ensembles in the final catalysts arising from the initial Fe-O-Ce bridges developed in the parent calcined samples.     

Polyaniline Modified CNTs and Graphene Nanocomposite for Removal of Lead and Zinc Metal Ions: Kinetics,Thermodynamics and Desorption Studies

A novel polyaniline-modified CNT and graphene-based nanocomposite (2.32–7.34 nm) was prepared and characterized by spectroscopic methods. The specific surface area was 176 m²/g with 0.232 cm³/g as the specific pore volume. The nanocomposite was used to remove zinc and lead metal ions from water; showing a high removal capacity of 346 and 581 mg/g at pH 6.5. The data followed pseudo-second-order, intraparticle diffusion and Elovich models. Besides this, the experimental values obeyed Langmuir and Temkin isotherms. The results confirmed that the removal of lead and zinc ions occurred in a mixed mode, that is, diffusion absorption and ion exchange between the heterogeneous surface of the sorbent containing active adsorption centers and the solution containing metal ions. The enthalpy values were 149.9 and 158.6 J.mol⁻¹K⁻¹ for zinc and lead metal ions. The negative values of free energies were in the range of −4.97 to −26.3 kJ/mol. These values indicated an endothermic spontaneous removal of metal ions from water. The reported method is useful to remove the zinc and lead metal ions in any water body due to the high removal capacity of nanocomposite at natural pH of 6.5. Moreover, a low dose of 0.005 g per 30 mL made this method economical. Furthermore, a low contact time of 15 min made this method applicable to the removal of the reported metal ions from water in a short time. Briefly, the reported method is highly economical, nature-friendly and fast and can be used to remove the reported metal ions from any water resource.     

杂原子介孔Ce-MCM-41分子筛的制备及其吸附脱除甲硫醚性能

以十六烷基三甲基溴化铵为模板剂,正硅酸乙酯(TEOS)为硅源,硝酸铈为铈源,采用水热法合成了杂原子介孔分子筛Ce-MCM-41。XRD和FT-IR表征结果表明,当加入的Ce/Si物质的量比小于0.04时合成了规整有序的介孔结构,并将Ce原子引入到MCM-41骨架中。N₂吸附-脱附测试获得MCM-41和Ce-MCM-41(Ce/Si物质的量比为0.04)的平均孔径分别为2.82和2.46 nm,孔容分别为0.762 1和 0.689 4 m³/g,BET比表面积分别为986.42和756.8 m²/g。NH₃-TPD表征结果表明,Ce-MCM-41的酸性要明显强于MCM-41,但两种分子筛的酸性均较弱。利用合成的MCM-41和Ce-MCM-41吸附脱除甲硫醚浓度为58 μg(甲硫醚)/g的甲硫醚/氮气混合气中的甲硫醚。甲硫醚分子尺寸的模拟结果为0.464 8 nm,可以很容易地进入分子筛的介孔孔道中。由于Ce-MCM-41分子筛具有较多的酸量,其硫吸附容量7.52 mg(S)/g明显高于MCM-41的4.57 mg(S)/g。MCM-41和Ce-MCM-41都具有较好的再生性能,再生3次后硫吸附容量仍可恢复到初始容量的80%,分别为3.52和 5.86 mg(S)/g。     

Magnetic Nitrogen-Doped Porous Carbon Nanocomposite for Pb(II) Adsorption from Aqueous Solution

We report in the present study the in situ formation of magnetic nanoparticles (Fe₃O₄ or Fe) within porous N-doped carbon (Fe₃O₄/N@C) via simple impregnation, polymerization, and calcination sequentially. The synthesized nanocomposite structural properties were investigated using different techniques showing its good construction. The formed nanocomposite showed a saturation magnetization (M_s) of 23.0 emu g⁻¹ due to the implanted magnetic nanoparticles and high surface area from the porous N-doped carbon. The nanocomposite was formed as graphite-type layers. The well-synthesized nanocomposite showed a high adsorption affinity toward Pb²⁺ toxic ions. The nanosorbent showed a maximum adsorption capacity of 250.0 mg/g toward the Pb²⁺ metallic ions at pH of 5.5, initial Pb²⁺ concentration of 180.0 mg/L, and room temperature. Due to its superparamagnetic characteristics, an external magnet was used for the fast separation of the nanocomposite. This enabled the study of the nanocomposite reusability toward Pb²⁺ ions, showing good chemical stability even after six cycles. Subsequently, Fe₃O₄/N@C nanocomposite was shown to have excellent efficiency for the removal of toxic Pb²⁺ ions from water.     

Synthesis,design of experiments and optimization of heterogeneous Fenton-like degradation of tartrazine by MgFe2O4 nano-catalyst

In this work, magnesium ferrites nanoparticles (MgFe₂O₄ NPs) were successfully fabricated by sol-gel auto-combustion (SGAC) method and were used in heterogeneous Fenton-like degradation of tartrazine. The obtained products were characterized using XRD, FTIR, SEM and EDX. XRD studies confirmed that the synthesized MgFe₂O₄ NPs had a cubic spinel structure. The average crystallite size was evaluated using the Debyee Scherrer formula and found to be in the range 16.18–28.55 nm. In FTIR spectra, two primary absorption bands at 571 cm^?1 and 415 cm^?1 were observed. The spinel ferrites are characterized by these bands and the EDX confirms the presence of the desired elements Mg, Fe, and O. The influences of operating parameters were examined using the Box Behnken statistical design (BD), including magnesium ferrite dosage (0.04–0.12 g/L), tartrazine concentration (30–50 mg/L) and H₂O₂ concentration (3.53–7.06 mM). Using analysis of variance, a significant quadratic model was created. Optimum conditions were magnesium ferrite dosage of 0.092 g/L, tartrazine concentration of 30.21 mg/L and H₂O₂ concentration of 6.66 mM, respectively. The predicted degradation efficiency within the optimum conditions as established by the suggested model was 98.4%. Confirmatory tests were carried out and the degradation efficiency of 98.9% was observed, which was in good agreement with the model's prediction. After five recuperation and reapplications, the catalyst's degradation efficiency remains stable. These findings indicate that a heterogeneous Fenton-like process utilizing MgFe₂O₄ is effective in advanced wastewater treatment.     

3‐D graphene‐supported mesoporous SiO2@Fe3O4 composites for the analysis of pesticides in aqueous samples by magnetic solid‐phase extraction with high‐performance liquid chromatography

Three‐dimensional graphene‐supported mesoporous silica@Fe₃O₄ composites (mSiO₂@Fe₃O₄‐G) were prepared by modifying mesoporous SiO₂‐coated Fe₃O₄ onto hydrophobic graphene nanosheets through a simple adsorption co‐condensation method. The obtained composites possess unique properties of large surface area (332.9 m²/g), pore volume (0.68 cm³/g), highly open pore structure with uniform pore size (31.1 nm), as well as good magnetic separation properties. The adsorbent (mSiO₂@Fe₃O₄‐G) was used for the magnetic solid‐phase extraction of seven pesticides with benzene rings in different aqueous samples before high‐performance liquid chromatography. The main parameters affecting the extraction such as adsorbent amount, volume of elution solvent, time of extraction and desorption, salt effect, oscillation rate were investigated. Under the optimal conditions, this method provided low limits of detection (S/N = 3, 0.525–3.30 μg/L) and good linearity (5.0–1000 μg/L, R² > 0.9954). Method validation proved the feasibility of the developed adsorbent, which has a high extraction efficiency and excellent enhancement performance for pesticides in this study. The proposed method was successfully applied to real aqueous samples, and satisfactory recoveries ranging from 77.5 to 113.6% with relative standard deviations within 9.7% were obtained.     

Rapid Determination of Mercury in Water by Stripping Voltammetry at a Gold-Modified Carbon Electrode

A procedure was developed for determining mercury in natural water by stripping voltammetry on a gold-modified carbon electrode. The concentration dependence of the anodic stripping current of mercury is linear in the range 0.02–5 g/L Hg(II). The interference of Fe(III), Cu(II), Cl^–, Br^–, I^–, and F^– ions with the determination of mercury was studied. Ozonation was used for rapid sample preparation. The detection limit for mercury was 0.02 g/L at an electrolysis time of 5 min.     

Instrumental neutron activation analysis of blood serum

Instrumental neutron activation analysis has been used to determine 15 trace elements in twelve blood serum samples taken from healthy students at Bilkent University in Ankara. The method allowed the determination of Sc, Cr, Mn, Fe, Co, Zn, Se, Rb, Cs, Ce, Eu, Tb, Hf, Ta and Hg, which occur at the g.ml^–1 to ng.ml^–1 levels. There are no values reported for Tb, Hf, Ce, Eu and Ta before. The other results are compared with the values reported in the literature. Most are in the range of the reported values except for Fe, Zn, Se and Cs.     

Strongly Basic Anion Exchange Resin Based on a Cross-Linked Polyacrylate for Simultaneous C.I. Acid Green 16, Zn(II), Cu(II), Ni(II) and Phenol Removal

The adsorption ability of Lewatit S5528 (S5528) resin for C.I. Acid Green 16 (AG16), heavy metals (Zn(II), Cu(II) and Ni(II)) and phenol removal from single-component aqueous solutions is presented in this study to assess its suitability for wastewater treatment. Kinetic and equilibrium studies were carried out in order to determine adsorption capacities, taking into account phase contact time, adsorbates’ initial concentration, and auxiliary presence (NaCl, Na₂SO₄, anionic (SDS) and non-ionic (Triton X100) surfactants). The pseudo-second-order kinetic model described experimental data better than pseudo-first-order or intraparticle diffusion models. The adsorption of AG16 (538 mg/g), phenol (14.5 mg/g) and Cu(II) (5.8 mg/g) followed the Langmuir isotherm equation, while the uptake of Zn(II) (0.179 mg^1−1/nL^1/n/g) and Ni(II) (0.048 mg^1−1/nL^1/n/g) was better described by the Freundlich model. The auxiliary’s presence significantly reduced AG16 removal efficiency, whereas in the case of heavy metals the changes were negligible. The column studies proved the good adsorption ability of Lewatit S5528 towards AG16 and Zn(II). The desorption was the most effective for AG16 (>90% of dye was eluted using 1 mol/L HCl + 50% v/v MeOH and 1 mol/L NaCl + 50% v/v MeOH solutions).     

The Use of High Surface Area Mesoporous-Activated Carbon from Longan Seed Biomass for Increasing Capacity and Kinetics of Methylene Blue Adsorption from Aqueous Solution

Microporous- and mesoporous-activated carbons were produced from longan seed biomass through physical activation with CO₂ under the same activation conditions of time and temperature. The specially prepared mesoporous carbon showed the maximum porous properties with the specific surface area of 1773 m²/g and mesopore volume of 0.474 cm³/g which accounts for 44.1% of the total pore volume. These activated carbons were utilized as porous adsorbents for the removal of methylene blue (MB) from an aqueous solution and their effectiveness was evaluated for both the adsorption kinetics and capacity. The adsorption kinetic data of MB were analyzed by the pseudo-first-order model, the pseudo-second-order model, and the pore-diffusion model equations. It was found that the adsorption kinetic behavior for all carbons tested was best described by the pseudo-second-order model. The effective pore diffusivity (D_e) derived from the pore-diffusion model had the values of 4.657 × 10⁻⁷–6.014 × 10⁻⁷ cm²/s and 4.668 × 10⁻⁷–19.920 × 10⁻⁷ cm²/s for the microporous- and mesoporous-activated carbons, respectively. Three well-known adsorption models, namely the Langmuir, Freundlich and Redlich–Peterson equations were tested with the experimental MB adsorption isotherms, and the results showed that the Redlich–Peterson model provided the overall best fitting of the isotherm data. In addition, the maximum capacity for MB adsorption of 1000 mg/g was achieved with the mesoporous carbon having the largest surface area and pore volume. The initial pH of MB solution had virtually no effect on the adsorption capacity and removal efficiency of the methylene blue dye. Increasing temperature over the range from 35 to 55 °C increased the adsorption of methylene blue, presumably caused by the increase in the diffusion rate of methylene blue to the adsorption sites that could promote the interaction frequency between the adsorbent surface and the adsorbate molecules. Overall, the high surface area mesoporous carbon was superior to the microporous carbon in view of the adsorption kinetics and capacity, when both carbons were used for the removal of MB from an aqueous solution.     

A Review on the Degradation of Pollutants by Fenton-Like Systems Based on Zero-Valent Iron and Persulfate: Effects of Reduction Potentials,pH, and Anions Occurring in Waste Waters

Among the advanced oxidation processes (AOPs), the Fenton reaction has attracted much attention in recent years for the treatment of water and wastewater. This review provides insight into a particular variant of the process, where soluble Fe(II) salts are replaced by zero-valent iron (ZVI), and hydrogen peroxide (H₂O₂) is replaced by persulfate (S₂O₈²⁻). Heterogeneous Fenton with ZVI has the advantage of minimizing a major problem found with homogeneous Fenton. Indeed, the precipitation of Fe(III) at pH > 4 interferes with the recycling of Fe species and inhibits oxidation in homogeneous Fenton; in contrast, suspended ZVI as iron source is less sensitive to the increase of pH. Moreover, persulfate favors the production of sulfate radicals (SO₄^•−) that are more selective towards pollutant degradation, compared to the hydroxyl radicals (^•OH) produced in classic, H₂O₂-based Fenton. Higher selectivity means that degradation of SO₄^•−-reactive contaminants is less affected by interfering agents typically found in wastewater; however, the ability of SO₄^•− to oxidize H₂O/OH⁻ to ^•OH makes it difficult to obtain conditions where SO₄^•− is the only reactive species. Research results have shown that ZVI-Fenton with persulfate works best at acidic pH, but it is often possible to get reasonable degradation at pH values that are not too far from neutrality. Moreover, inorganic ions that are very common in water and wastewater (Cl⁻, HCO₃⁻, CO₃²⁻, NO₃⁻, NO₂⁻) can sometimes inhibit degradation by scavenging SO₄^•− and/or ^•OH, but in other cases they even enhance the process. Therefore, ZVI-Fenton with persulfate might perform unexpectedly well in some saline waters, although the possible formation of harmful by-products upon oxidation of the anions cannot be ruled out.     

Synthesis of nanoscale zero‐valent iron modified graphene oxide nanosheets and its application for removing tetracycline antibiotic: Response surface methodology

Nowadays, pharmaceutical antibiotics are known as a serious class of pollutants. Therefore, it is important to develop effective methods for removing these pollutants from aqueous media. Different methods were applied for this purpose, and among these methods, chemical reduction by a cheap and eco‐friendly nanocatalyst is the most efficient and simplest method. In this research, based on graphene oxide supported by zero‐valent iron in mono‐, bi‐, and tri‐metallic systems, various nanocomposites were synthesized and used to degrade tetracycline as a model antibiotic from aqueous media. An investigation was carried out on the synergic effect among graphene oxide and the nano zero‐valent iron‐based tri‐metallic system as well as removal efficiencies. It was found that higher degradation efficiency is yielded by graphene oxide supported by Fe/Cu/Ag tri‐metallic system. The maximum synergic effect occurs at an acidic medium. The Brunauer–Emmett–Teller, Fourier transform spectroscopy, scanning electron microscopy‐energy dispersive X‐ray analysis, transmission electron microscopy, and X‐ray diffraction analysis were used to characterize the synthesized nanocomposites, which has successfully proved the loading of nanoscale Fe/Cu/Ag tri‐metallic on a graphene oxide support. The central composite design was used to model and optimize all involved variables affecting antibiotic removal efficiency. The consequences illustrated the optimum condition regarding the removal of 50 ppm of tetracycline, for the nanocomposites dose of 3.0 mg ml^?1, the contact time of 30 min, and pH of 2, was achieved using the simplex non‐linear optimization method. Moreover, antibiotic adsorption kinetic models were also investigated. Finally, the tetracycline removal from aqueous media at different concentrations, 25, 50, and 75 ppm, was successful by applying the proposed nanocomposite, and the results showed tetracycline removal efficiencies of above 70%.     

Studies on the Efficiency of Iron Release from Fe(III)-EDTA and Fe(III)-Cit and the Suitability of These Compounds for Tetracycline Degradation

Iron ions can be used to degrade tetracycline dispersed in nature. Studies of absorption and fluorescence spectra and quantum chemistry calculations showed that iron is more readily released from Fe(III)-citrate than from Fe(III)-EDTA, so Fe(III)-citrate (Fe(III)-Cit) is more suitable for tetracycline (TC) degradation. At 30 °C, a severe degradation of TC by Fe(III)-Cit occurred as early as after 3 days of incubation in the light, and after 5 days in the dark. In contrast, the degradation of TC by Fe(III)-EDTA proceeded very slowly in the dark. By the fifth day of incubation of TC with Fe(III)-Cit in darkness, the concentrations of the former compound dropped by 55% and 75%, at 20 °C and 30 °C, respectively. The decrease in tetracycline concentrations caused by Fe(III)-EDTA in darkness at the same temperatures was only 2% and 6%, respectively. Light increased the degradation rates of TC by Fe(III)-EDTA to 20% and 56% at 20 °C and 30 °C, respectively. The key role of the light in the degradation of tetracycline by Fe(III)-EDTA was thus demonstrated. The TC degradation reaction showed a second-order kinetics. The rate constants of Fe(III)-Cit-induced TC degradation at 20 °C and 30 °C in darkness were k = 4238 M⁻¹day⁻¹ and k = 11,330 M⁻¹day⁻¹, respectively, while for Fe(III)-EDTA were 55 M⁻¹day⁻¹ and 226 M⁻¹day⁻¹. In light, these constants were k = 15,440 M⁻¹day⁻¹ and k = 40,270 M⁻¹day⁻¹ for Fe(III)-Cit and k = 1012 M⁻¹day⁻¹ and 2050 M⁻¹day⁻¹ at 20 °C and 30 °C; respectively. A possible reason for the higher TC degradation rate caused by Fe(III)-Cit can be the result of its lower thermodynamical stability compared with Fe(III)-EDTA, which we confirmed with our quantum chemistry calculations. Two quantum chemistry calculations showed that the iron complex with EDTA is more stable (the free energy of the ensemble is 15.8 kcal/mol lower) than the iron complex with Cit; hence, Fe release from Fe(III)-EDTA is less effective.     

Photocatalytic Activity of Fe and Ce Co‐doped Mesoporous TiO2 Catalyst under UV and Visible Light

The catalysts of un‐doped, single‐doped and co‐doped mesoporous titanium dioxide (MTiO₂) were prepared by a template method with tetrabutyltitanate (Ti(OC₄H₉)₄) as a Ti source material and Pluronic P123 as a template. The photo‐absorbance of the obtained catalysts was measured by UV‐vis absorption spectroscopy, and the photocatalytic activities of the prepared samples under UV and visible light were estimated by measuring the degradation rate of methyl orange (MO) (50 mg/L) in an aqueous solution. It was shown that the co‐doped MTiO₂ could be activated by visible light and could thus be used as an effective catalyst in photo‐oxidation reactions. The effect of Fe and Ce co‐dopants on the material properties was investigated by X‐ray diffraction (XRD), scanning electron microscopy (SEM) and N₂ adsorption‐desorption isotherm measurement. The characterizations indicated that the photocatalysts possessed a homogeneous pore diameter of ca. 10 nm with high surface area of ca. 150 m²/g. The photocatalytic activity of MTiO₂ co‐doped with Fe and Ce was markedly improved due to the synergistic actions of the two dopants.     

Treatment of industrial contaminants with zero-valent iron- and zero-valent aluminium-activated persulfate: a case study with 3,5-dichlorophenol and 2,4-dichloroaniline

Zero-valent iron (ZVI)- and zero-valent aluminium (ZVA)-activated persulfate (PS) oxidation procedure was applied to remove the industrial pollutants 3,5-dichlorophenol (3,5-DCP; 12.27 µM) and 2,4-dichloroaniline (2,4-DCA; 12.34 µM) from aqueous solutions. The effects of PS concentration and pH were investigated to optimize heterogeneous treatment systems. Negligible removals were obtained for both pollutants by individual applications of nanoparticles (1 g/L) and PS (1.00 mM). PS activation with ZVI resulted in 59% (1.00 mM PS; 1 g/L ZVI; pH 5.0; 120 min) and 100% (0.75 mM PS; 1 g/L ZVI; pH 5.0; 80 min) 3,5-DCP and 2,4-DCA removals, respectively. The ZVA/PS treatment system gave rise to only 31% 3,5-DCP (1.00 mM PS; 1 g/L ZVA; pH 3.0; 120 min) and 47% 2,4-DCA (0.25 mM PS; 1 g/L ZVA; pH 3.0; 120 min) removals. The pH decreases from 5.0 to 3.0 and from 3.0 to 1.5 enhanced contaminant removals for ZVI/PS and ZVA/PS treatments, respectively. Pollutant removal rates were in correlation with the consumption rates of the oxidants. Metal ion (Al, Fe) release increased in the presence of PS and with decreasing pH.