Impact of Charge Transfer Complex on the Dielectric Relaxation Processes in Poly(methyl methacrylate) Polymer

The impact of the charge transfer complex on the dielectric relaxation processes in free poly(methyl methacrylate) (PMMA) polymer sheets was investigated. The frequency dependence of dielectric properties was obtained over the frequency range 0.1 Hz–1 MHz at temperatures ranging between 303 K and 373 K for perylene dye and acceptors (picric acid (PA) and chloranilic acid (CLA)) in an in situ PMMA polymer. The TG/dTG technique was used to investigate the thermal degradation of the synthesized polymeric sheets. Additionally, the kinetic parameters have been assessed using the Coats–Redfern relation. The dielectric relaxation spectroscopy of the synthesized polymeric sheets was analyzed in terms of complex dielectric constant, dielectric loss, electrical modulus, electrical conductivity, and Cole–Cole impedance spectroscopy. α- and β-relaxation processes were detected and discussed. The σ(ω) dispersion curves of the synthesized polymeric sheets show two distinct regions with increasing frequency. The impedance data of the synthesized polymeric sheets can be represented by the equivalent circuit (parallel RC).     

Enhanced dielectric properties of polyethylene glycol (PEG) modified BaTiO<Subscript>3</Subscript> (BT)-poly(vinylidene fluoride) (PVDF) composites

To improve the compatibility between the ceramic particle and polymer matrix, the surface modifier polyethylene glycol (PEG) was used for the modification of BaTiO₃ (BT) particles as fillers in the poly(vinylidene fluoride) (PVDF) matrix via solution casting techniques. The structural analysis of the composite characterized by X-ray diffraction confirms the tetragonal structure. The results showed that the PEG modified BT-PVDF composites had a higher dielectric constant (≈192) and relatively lower dielectric loss value at 1000 Hz. The Nyquist plot suggests the contribution of only bulk effect present in the composites. The AC electrical conductivity studies obey Jonscher’s universal power law by fitting AC conductivity data which reveals the potential utility of the composites for ideal capacitor and microscopic reasons for this improvement were presented. Furthermore, the remnant polarization was significantly improved and maximum polarization was observed for PEG modified BT-PVDF composites.     

Effect of silver nanoparticles on frequency and temperature-dependent electrical parameters of a discotic liquid crystalline material

The effect of silver nanoparticles (AgNPs) of diameters 6 and 100 nm on a discotic liquid crystalline material, namely 2,3,6,7,10,11-hexabutyloxytriphenylene (in short HAT4), has been observed in thermodynamic, electrical and optical texture studies. Silver nanoparticles (0.6 wt%) of diameter ~6 nm demonstrate a negligible (but ~100 nm shows appreciable) effect on the broad temperature range plastic columnar hexagonal (Col_hex) phase (~65.0°C) of pure HAT4. The dielectric studies have been carried out in the frequency range of 10 Hz–35 MHz under homeotropic anchoring conditions of the molecules. In the low frequency region of pure HAT4 and its AgNP composites, a relaxation mode has been observed. AgNPs of 6 nm elevate the value of dielectric permittivity of the plastic columnar hexagonal phase of pure HAT4. The dc conductivity of pure HAT4 and its AgNP composite (6 and 100 nm) material has been determined. The optical band gap for pure and AgNP composites of HAT4 has been determined by the ultraviolet-visible study. Due to insertion of AgNPs, the optical band gap of HAT4 has reduced.     

Optical and electrical properties of copper alumina nanoparticles reinforced chlorinated polyethylene composites for optoelectronic devices

The incorporation of transition metal oxide fillers into the polymer matrix through solution mixing polymerization imparts enhanced electrical and thermal properties. The present work focused on the optical properties, crystallinity, thermal stability, temperature-dependent conductivity, dielectric constant and modulus of chlorinated polyethylene/copper alumina (CPE/Cu–Al₂O₃) nanocomposites. Optical absorption measured using an ultraviolet–visible (UV–visible) spectrometer shows enhanced intensity and a blue shift for CPE/Cu–Al₂O₃ nanocomposites. The bandgap energy of CPE/Cu–Al₂O₃ nanocomposites was lower than pure CPE and minimum bandgap energy was recorded for a 7 wt% composites. The X-ray diffraction demonstrates that Cu–Al₂O₃ nanoparticles were uniformly introduced into the CPE matrix. Thermogravimetric analysis (TGA) manifests improved thermal stability of nanocomposites. Dielectric properties decrease with frequency, whereas AC conductivity increases with frequency, and both AC conductivity and dielectric properties increase with temperature. The maximum AC conductivity and dielectric constant were obtained for 7 wt % nanofiller loaded sample. For all systems, the activation energy for electrical conductivity decreases with rising temperatures. The experimental dielectric constant values of CPE nanocomposites were correlated with different theoretical models. The Bruggeman model was in good agreement with the experimental permittivity. The impedance experiments showed a decreasing trend with temperature, indicating the semiconducting nature of prepared nanocomposites.     

Structural and electrical properties of polyvinyl alcohol (PVA):Methyl cellulose (MC) based solid polymer blend electrolytes inserted with sodium iodide (NaI) salt

This paper studies the structural and electrical properties of solid polymer blend electrolytes based on polyvinyl alcohol (PVA) and methylcellulose (MC) incorporated with sodium iodide (NaI). The polymer electrolyte films were assembled through a solution casting technique. The host matrix, which is doped with different NaI salt concentrations between 10 and 50 wt%, utilizes the most amorphous blend compositions (60 wt% Polyvinyl alcohol and 40 wt% methylcellulose). The structural behaviour of the electrolyte films was examined utilizing X-ray diffraction (XRD) and Fourier transformation infrared (FTIR) techniques. The semi crystalline nature of PVA:MC with inserted NaI was derived from the X-ray diffraction studies, while the XRD analysis suggests that the highest ion conductive sample displays the minimum crystalline nature. The interaction between polymer blends and inserted salt was conceived from the FTIR investigation. Shifting of peaks and variation in the intensity of FTIR bands was detected. To investigate the structural properties and calculate the degree of crystallinity of the films, the (XRD) technique was employed, while electrical impedance spectroscopy (EIS) was utilized for studying the conductivity of the samples. In order to comprehend all of the electrical properties of the ion-conducting systems, the EIS outcome of each electrolyte was matched with Equivalent Electrical Circuits (EEC) s. Ion transport parameters including mobility, carrier density and diffusion are well assessed for the samples and the dielectric properties were compared with the conductivity measurement. At lower frequencies, the dielectric constant was elevated and dielectric loss was detected. Loss tangent and electric modulus plots were used to study the relaxation nature of the samples. The highest ambient temperature conductivity of PVA loaded 50 wt% of NaI was determined to be 1.53 × 10⁻⁵ S/cm. The loss tangent relaxation peak shifts towards high-frequency side which indicates the decrease of relaxation time and faster ion dynamics.     

Electrical, optical, thermoelectric power, and dielectrical properties of organic semiconductor poly(1,12-bis(carbazolyl) dodecane) film

Electrical conductivity, optical, thermoelectric, and dielectrical properties of the poly(1,12-bis(carbazolyl) dodecane) film have been investigated. The activation energy for electrical conductivity and room-temperature electrical conductivity (at 25 degrees C) values were found to be 0.25 eV and 2.65 x 10-6 S/cm, respectively. The thermoelectric power results suggest that the conductivity is due to large polarons (i.e., the carriers in polymer move by hopping in the localized states at band gap edges). Electrical conductivity and thermoelectric power results confirm that the polymer is a p-type organic semiconductor. Optical absorption results suggest that the direct allowed transitions are dominant in the fundamental absorption edge in the polymer with optical band gap value of 2.72 eV. The refractive index dispersion of the polymer obeys the single oscillator model with oscillator energy (Eo = 3.06 eV) and dispersion energy (Ed = 17.82 eV) values. Alternating current conductivity results suggest that the hopping conductivity is dominant in the polymer. The dielectrical properties exhibit a non-Debye relaxation.     

Effect of poly(ethylene glycol) on the dielectric properties of poly(vinylidene fluoride)/BiFeO<Subscript>3</Subscript>/poly(ethylene glycol) composite films for electronic applications

In the present work a series of poly(vinylidene fluoride)/BiFeO₃/poly(ethylene glycol) composite films were prepared by solvent casting method with poly(vinylidene fluoride) as polymer matrix, bismuth ferrite as ceramic filler and poly(ethylene glycol) as binding agent as well as enhancer. The structural analysis of the composite films by X-ray diffraction confirms that the composites have a distorted rhombohedral structure. The micro-structural analysis shows that the use of poly(ethylene glycol)in the composite films enhances the homogeneity as well as compatibility of BiFeO₃ particles within the poly(vinylidene fluoride) matrix. The dielectric and electrical study done by impedance analyzer reveals that with an increase in poly(ethylene glycol) concentration, there is a subsequent increase in dielectric constant as well as AC electrical conductivity. Finally, the ferroelectric behavior of the composite confirms that the ferroelectric properties of the composites are enhanced by the addition of BiFeO₃ with an increase in poly(ethylene glycol) concentrations. These preliminary results give an idea for possible applications of this type of composites in the field of electronic applications.     

Study on conductivity and dielectric behavior of chemically synthesized polypyrrol dodecylbenzene sulfonic acid blended with poly(methyl methacrylate)

Polypyrrole (PPy) doped with dodecylbenzene sulfonic acid was synthesized and was blended with compatible polymer PMMA in chloroform. Flexible and free-standing films with compositions PPy: PMMA = 10: 90, 20: 80, 30: 70, and 50: 50 were obtained. The percentage of crystallinity and particle size of synthesized polymers were estimated from X-rays diffraction studies. Scanning Electron Micrographs showed that phase separation was observed and compatibility of the mixture decreased with increase of PMMA content. The dielectric measurements were performed in the frequency range 0.1 kHz–1 MHz in temperature range 303–473 K. The frequency dependent conductivity (σ_ac) obeyed a power law of frequency with an exponent s < 1. Electric modulus formalism exhibits a peak in frequency. The peak of conductivity relaxation shifted towards higher frequencies and the magnitude of relaxation decreased with the increase of PMMA content in the composites.     

Electrical and Structural Properties of Poly (Methyl Methacrylate) Doped Potassium Iodide (KI) Solid Polymer Electrolyte

A high-conducting salt-doped polymer electrolyte layer has been created here for use in photocell technologies. The solution casting method is used to produce ion conducting film where poly (methyl methacrylate) (PMMA) is used as the host polymer and potassium iodide (KI) as the dopant. The conductivity and amorphic increases of the polymer electrolytes with the addition of salt concentrations helps in the enhancement of the charge transfer properties. Using electrochemical impedance spectroscopy (EIS), ionic conductivity is evaluated where maximum conductivity is 3.99 × 10⁻⁶ S cm^-1 at 20 wt% KI concentration. Polarized optical microscopy (POM) shows the reduction in crystallinity by salt doping, while Fourier transforms infrared spectroscopy (FTIR) shows the complexation as well as composite nature of the film. Ionic transference number (t_ion) measurement shows the predominantly ionic nature of this polymer electrolyte.     

聚合物-锂改性蒙脱石复合材料离子迁移

以聚合物（ＰＥＯ,ＰＥＯ－ＰＭＭＡ）和锂改性蒙脱石作为主要原料,采用聚合物粉末直接熔融嵌入的方法,制备聚合物－蒙脱石复合材料．利用ＮＭＲ、ＡＣ阻抗等分析方法探讨了复合材料中聚合物链对 Ｌｉ＋离子迁移的影响．结果表明,聚合物（ＰＥＯ）嵌入蒙脱石层间,层间聚合物链的无序度增大,有利于Ｌｉ＋离子迁移．ＰＭＭＡ引入对ＰＥＯ链的改性,进一步加大聚合物链的无序度,更易于层间Ｌｉ＋离子迁移;复合材料的常温离子电导率接近１０－２Ｓ·ｃｍ－１,且具有良好的温度稳定性．     

Electrical transport properties of an organic semiconductor on polyaniline doped by boric acid

The electrical conductivity, thermoelectric power, and dielectric properties of polyaniline doped by boric acid (PANI‐B) have been investigated. The room temperature electrical conductivity of PANI‐B was found to be 1.02 × 10^?4 S cm^?1. The thermoelectric power factor for the polymer was found to be 0.64 µW m^?1 K^?2. The optical band gap of the PANI‐B was determined by optical absorption method, and the PANI‐B has a direct optical band gap of 3.71 eV. The alternating charge transport mechanism of the polymer is based on the correlated barrier hopping (CBH) model. The imaginary part of the dielectric modulus for the PANI‐B suggests a temperature dependent dielectric relaxation mechanism. Electrical conductivity and thermoelectric power results indicate that the PANI‐B is an organic semiconductor with thermally activated conduction mechanism. Copyright © 2008 John Wiley & Sons, Ltd.     

Filler network structure in graphene nanoplatelet (GNP)-filled polymethyl methacrylate (PMMA) composites: From thermorheology to electrically and thermally conductive properties

In this work, graphene nanoplatelet (GNP) filled polymethyl methacrylate (PMMA) composites were prepared using solution method via a specially designed route and relatively high thermal conductivities of the composites were achieved at a low GNP loading. The effect of GNP content on rheological behavior, thermal and electrical conductivity of the composites was intensively investigated. Thermorheological complexity was displayed at elevated GNP loading, and the rheological percolation threshold of GNP in PMMA decreased from 7.96 wt% at 220 °C to 4.02 wt% at 260 °C according to Winter-Chambon method, suggesting that GNP was more likely to form a seepage network at higher temperature. The DMTA results showed that the increase in moduli of the composites should be ascribed to the formation of the GNP-GNP network structure. The electrical conductivity of the composites underwent a sudden jump by seven orders of magnitude, which also indicated the formation of a GNP conductive pathway in the matrix with an electrical percolation threshold of 2–4 wt%. The results of transient temperature measurement were in good consistent with the thermal conductivity versus GNP loading, which was compared with various thermal conduction models with a modified Agari model presenting an acceptable evaluation of the dispersion status of GNP in the matrix. The experimental electrical and thermal conductivities as a function of GNP content could well be interpreted by the filler network structure as observed in morphological studies.     

A comparative study on the AC/DC conductivity,dielectric and optical properties of polystyrene/graphene nanoplatelets (PS/GNP) and multi-walled carbon nanotube (PS/MWCNT) nanocomposites

Polystyrene/graphene nanoplatelets (PS/GNP) and polystyrene/multi-walled carbon nanotube (PS/MWCNT) nanocomposites were prepared through solution mixing processing. The effect of carbon filler (CF) (GNP or MWCNT) doping on the DC/AC electrical conductivity, dielectric characteristics and optical parameters (absorption coefficient, α and band gap energy, E_g) of nanocomposites were investigated and compared for similar doping concentrations. The observed behavior of the DC surface conductivity for PS/CF nanocomposites was explained according to the classical percolation theory, where the percolation thresholds (ϕ_c) for PS/GNP and PS/MWCNT nanocomposites were determined as 12.0 vol% and 3.81 vol% and the critical exponents (t) were calculated as 2.19 and 2.13, respectively. These results indicate that CFs create three dimensional CF network in PS matrix. The dielectric relaxation properties and the AC conductivity studied by means of Broadband Dielectric Spectroscopy (BDS) measurements, showed that the presence of carbon fillers significantly enhanced the capacitive/charge storage capabilities of the nanocomposites. The optical band gap energies (E_g) of PS/GNP and PS/MWCNT nanocomposites were obtained by using Tauc method. From applicative point of view, with their enhanced dielectric and AC conductivity properties of the PS/GNP and PS/MWCNT nanocomposites have the potential to be used in energy storage and electromagnetic interference (EMI) shielding applications.     

Structural,thermal and electrical properties of poly(methyl methacrylate)/CaCu3Ti4O12 composite sheets fabricated via melt mixing

Poly(methyl methacrylate) (PMMA) and CaCu₃Ti₄O₁₂ (CCTO) composites were fabricated via melt mixing followed by hot pressing technique. These were characterized using X-ray diffraction, thermo gravimetric, thermo mechanical, differential scanning calorimetry, fourier transform infrared (FTIR) and Impedance analyser for their structural, thermal and dielectric properties. Composites were found to have better thermal stability than that of pure PMMA. However, there was no significant difference in the glass transition (T _g ) temperature between the polymer and the composite. The appearance of additional vibrational frequencies in the range 400–600 cm^?1 in FTIR spectra indicated a possible interaction between PMMA and CCTO. The composite, with 38 vol% of CCTO (in PMMA), exhibited remarkably low dielectric loss at high frequencies and the low-frequency relaxation is attributed to the interfacial polarization/MWS effect. The origin of AC conductivity particularly in the high-frequency region was attributed to the electronic polarization.     

Dehydration-induced structural relaxation effects in poly(methyl methacrylate)

The Thermally Stimulated Depolarization (TSD) dielectric technique and Dielectric Relaxation Spectroscopy (DRS) have been used in order to investigate aging phenomena in poly(methyl methacrylate) (PMMA). Earlier TSD studies on amorphous PMMA report peculiar dielectric relaxation signals within the range of the glass transition (at ∼378 K) and the secondary relaxation (∼230 K). In the present study, an intense TSD current relaxation band maximizing around 310 K is tentatively attributed to the molecular mobility due to a residual free volume below the glass transition temperature, T_g, that allows structural recovery at the free volume released from the desorption of H₂O molecules during evacuation. Limited motions in the main backbone provoke dipole (re)orientation of the ester carbonyl pendant groups with an activation energy E=0.85±0.05 eV, being responsible for the latter dielectric relaxation effect. Alternative attributions based on the short-range jump relaxation of electric charges and boundary effects are also discussed.     

Synthesis and electrical and optoelectronic properties of poly[(N-benzyldiphenylamino)methane]

Poly[(N-benzyldiphenylamino)methane] was synthesized by the condensation polymerization of benzyldiphenylamine and formalin (30% HCOH in water) and examined for electrical and optoelectronic properties. Dark conductivity and photoconductivity of the polymer film were investigated by steady-state measurements. Current-voltage characteristics and intrinsic photoconduction of the polymer in the visible wavelength range were studied. A superlinear current increase is tentatively explained in the light of the Poole-Frenkel effect. Dielectric constant and dielectric loss parameters of the polymer are independent of frequency (50 Hz–10 kHz) and temperature (273–323 K), respectively. The growth and decay rates of the photocurrent depend on the applied voltage, and the photocurrent varies directly with the light intensity. The activation energies for dark conductivity and photoconductivity are 1.16 eV and 1.05 eV, respectively, and the optical energy band gap as evaluated from absorption coefficient spectra is 2.86 eV.     

Polarisation switching and molecular relaxation behaviour of anthraquinone dye-dispersed polymer-stabilised ferroelectric liquid crystal composites

Guest–host polymer-stabilised ferroelectric liquid crystal (GH-PSFLC) composite films have been prepared with dispersion of small concentration (0.1, 0.25 and 0.5 wt%) of anthraquinone blue dye in PSFLC host matrix via a polymerisation-induced phase separation (PIPS) process. The variation in alignment and size of twisted fibril has been observed in the optical textures of the guest–host composites with different wt/wt ratio of anthraquinone dye. The electrical and dielectric properties of PSFLC mixture and its guest–host derivatives are studied. Our results showed that an optimum amount of dye concentration (0.1 wt%) enhances the dielectric permittivity as well as the spontaneous polarisation of the GH-PSFLC material in the SmC* phase.     

Fabrication and electrical conductivity of poly(methyl methacrylate) (PMMA)/carbon black (CB) composites: comparison between an ordered carbon black nanowire-like segregated structure and a randomly dispersed carbon black nanostructure

Poly(methyl methacrylate) (PMMA)/carbon black (CB) composites were fabricated using two different mixing methods: (1) mechanical mixing and (2) solution mixing of the precursors, followed by compression molding. The microstructures obtained were examined by optical and scanning electron microscopy. Electrical properties were measured using impedance spectroscopy over a wide frequency range (10(-3) to +10(9) Hz). With the mechanical mixing method, a segregated structure is produced with PMMA particles forming faceted grains with carbon black particles aligning to form a network of 3D-interconnected nanowires. This microstructure allows percolation to occur at a low volume fraction of 0.26 vol % CB. In contrast, specimens made by the solution method have a microstructure where carbon black is distributed more randomly throughout the bulk, and thus, the percolation threshold is higher (2.7 vol % CB). The electrical properties of the PMMA/CB composites fabricated by the mechanical mixing method are comparable to those obtained with single-wall nanotubes as fillers.     

微波介质材料BaEu2Ti4O12的交流阻抗谱表征

采用交流阻抗谱技术对微波介质材料BaEu2Ti4O12进行了表征。分析了lgε/lgf, Z″/Z′和Y′/lgf等图谱的特征与材料性能的关系.研究结果表明：1）阻抗谱测试得到的介电常数与所发表的微波测试结果有很好的一致性,高频下得到的介电常数实际上是晶粒和晶界的净结果,高质量烧结的材料应具有薄的晶界，因而应表现出较大的介电常数; 2）如果将材料从高温下缓慢降温或在O2气氛中退火，材料的导电性都会下降，其原因可以理解为这样处理的材料氧空位浓度降低，进而可以推测这有利于降低材料的介电损失.     

Molecular Dynamics and Structure of Poly(Methyl Methacrylate) Chains Grafted from Barium Titanate Nanoparticles

Core−shell nanocomposites comprising barium titanate, BaTiO₃ (BTO), and poly(methyl methacrylate) (PMMA) chains grafted from its surface with varied grafting densities were prepared. BTO nanocrystals are high-k inorganic materials, and the obtained nanocomposites exhibit enhanced dielectric permittivity, as compared to neat PMMA, and a relatively low level of loss tangent in a wide range of frequencies. The impact of the molecular dynamics, structure, and interactions of the BTO surface on the polymer chains was investigated. The nanocomposites were characterized by broadband dielectric and vibrational spectroscopies (IR and Raman), transmission electron microscopy, differential scanning calorimetry, and nuclear magnetic resonance. The presence of ceramic nanoparticles in core–shell composites slowed down the segmental dynamic of PMMA chains, increased glass transition temperature, and concurrently increased the thermal stability of the organic part. It was also evidenced that, in addition to segmental dynamics, local β relaxation was affected. The grafting density influenced the self-organization and interactions within the PMMA phase, affecting the organization on a smaller size scale of polymeric chains. This was explained by the interaction of the exposed surface of nanoparticles with polymer chains.