Dynamics of the adsorption of freons

The elution adsorption dynamics of some adsorption systems (freon-active carbon) has been studied at two temperatures. The peculiarities of the adsorption dynamics, which are determined by the properties of the adsorption system, have been established. A possibility to calculating elution curves based on the equilibrium adsorption layer model is shown. Preliminary results of the influence of the parameters of the adsorption system on the coefficient of the effective kinetic model are obtained.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1373–1376, June, 1996.     

Effect of agitation on removal of acetic acid from pretreated hydrolysate by activated carbon

The effect of agitation on the adsorption of acetic acid by activated carbon was tested utilizing an external mass transfer-diffusion model. Simulated pretreated biomass was contacted with activated carbon under prescribed conditions of temperature and agitation. Adsorption isotherm studies are presented as well as batch kinetic rate studies. Use of these data enabled the determination of isotherm constants, an external mass transfer coefficient, and an effective diffusivity for each agitation rate studied. The external film coefficient results ranged from 33.62 μm/s to a complete absence of external mass transfer resistance, and the diffusivity results ranged from 0.8625 to 10.70 μm²/s. The optimum combination of no external film resistance, and highest diffusivity, 10.70 μm²/s, occurred at 250 rpm and 25°C. The results of these models and the experimental parameters suggested an efficacious method and conditions for the removal of this undesirable chemical.     

Determination of competitive adsorption isotherm parameters of pindolol enantiomers on alpha1-acid glycoprotein chiral stationary phase

In this paper, inverse method (IM) was used to determine the binary competitive adsorption isotherm of pindolol enantiomers by a least-square fitting of the proposed model to the experimentally measured elution curves of racemic pindolol. The isotherm parameters were determined by minimizing the least-square error using an adaptation of genetic algorithm, non-dominated sorting genetic algorithm with jumping genes (NSGA-II-JG). An equilibrium dispersive (ED) model combined with bi-Langmuir isotherm was used in predicting the elution profiles. The determined parameters show good agreement with the experimental profiles at various experimental conditions such as sample volume, concentration and flow rates of the racemic mixture. Robustness and validity of the isotherm parameters were also verified by frontal analyses at various step inputs. Results from both the pulse tests and the frontal analysis indicate that adsorption isotherm derived from the inverse method is quite reliable. This method requires relatively less number of experiments to be performed and therefore, lower experimental costs confirming that inverse method is an attractive alternative approach of experimental technique in determining the competitive adsorption isotherm for binary systems.     

Kinetic and equilibrium studies of urea adsorption onto activated carbon: Adsorption mechanism

We found that activated carbon effectively removed urea from solution and that urea adsorption onto activated carbon followed a pseudo-second-order kinetic model. We classified the urea adsorption on activated carbon as physical adsorption and found that it was best described by the Halsey adsorption isotherm, suggesting that the multilayer adsorption of urea molecules on the adsorption sites of activated carbon best characterized the adsorption system. The mechanism of adsorption of urea by activated carbon involved two steps. First, an amino (–NH₂) group of urea interacted with a carbonyl (–C?O) group and a hydroxyl (?OH) group on the surface of activated carbon via dipole–dipole interactions. Next, the –C?O group of the urea molecule adsorbed to the activated carbon interacted with another –NH₂ group from a second urea molecule, leading to multilayer adsorption.     

Non-isothermal Modelling of Hydrocarbon Adsorption on A Granulated Active Carbon

The adsorption of n -butane on extruded cylindrical activated carbon grains is studied providing two kinds of information: the influence of the temperature and the hydrocarbon partial pressure on the adsorption dynamics (kinetic study) and on the adsorption capacities (thermodynamic study). The thermodynamic aspect could be interpreted by a Langmuir model. From a kinetic point of view, we have experimentally proved that strong temperature variations occur inside the particles during the adsorption. In this paper, a kinetic model including both mass and heat transfer phenomena is proposed. Good agreement is found between the kinetic model predictions and the experimental mass and temperature variations inside the grain during the hydrocarbon adsorption. This revised version was published online in August 2006 with corrections to the Cover Date.     

Adsorptive removal of malachite green and Rhodamine B dyes on Fe3O4/activated carbon composite

This study demonstrates the adsorption experiments of toxic dyes malachite green (MG) and Rhodamine B (RB) on Fe₃O₄-loaded activated carbon (AC). AC, which is known to be a high-capacity adsorbent, was aimed to be easily separated from aqueous media by loading it with Fe₃O₄. Fe₃O₄-loaded AC was prepared by the coprecipitation method and named magnetic activated carbon (M-AC), and the produced M-AC was characterized by x-ray diffraction (XRD), thermogravimetric analysis (TGA), and pH_pzc analyses. MG and RB adsorption by the M-AC was performed separately by batch technique and the effects of adsorbent amount, solution pH, and initial dye concentration on the adsorption were explored. Maximum removal efficiencies were found to be 96.11% for MG and 98.54% for RB, and the Langmuir isotherm model was the most fitted isotherm model for the adsorption. The kinetic and thermodynamic studies showed that the adsorption proceeded via the pseudo-second-order kinetic model and endothermic in-nature for both dyes.     

Microwave‐synthesized Pepper Peduncle Carbon,Characterization, and Its Adsorption Studies

Adsorption on activated carbon is an efficient method for the removal of toxic dyes. However, since commercially available charcoal is quite expensive, activated carbon obtained from agricultural by‐products may serve as a good replacement. In this study, activated carbon was prepared from pepper peduncle, an agricultural waste product, by microwave activation. The synthesized carbon was characterized by X‐ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, and thermal gravimetric analysis techniques. It was then used for the adsorption of methylene blue dye from an aqueous solution, which was studied as a function of the dye concentration, contact time, and temperature. The adsorption data were fitted to Freundlich and Langmuir isotherm models. The adsorption kinetics was studied by employing first‐ and second‐order kinetic models, and it was found that the adsorption of methylene blue on the synthesized activated carbon follows a second‐order kinetic model. Effect of temperature on the adsorption process was studied, and the thermodynamic parameters such as activation energy, change in enthalpy, entropy, and free energy of adsorption were calculated on the basis of the absolute theory of reaction rate expressions. About 99.5–91.8% of the dye was removed for an initial dye concentration in the range 20–100 mg/g in 1 h. Thus the synthesized activated carbon was found to be very efficient in adsorbing the dye.     

Adsorption of Dyes from Aqueous Textile By-Products on Activated Carbon from Scenedesmus obliquus

The adsorption of activated carbon prepared from Scenedesmus obliquus (algae) was evaluated through adsorption of Astrazon red. The adsorption efficiency of activated carbon was determined based on the specific surface area and pore size distribution. These results were compared with the results obtained with untreated algae. Approximately a 3-fold increase in the percentage of dye removal was observed for activated carbon compared to the untreated material. The primary reason for this observation may be the increase in specific surface area and total pore volume by chemical activation from 0.0136 to 423.7001?m²?g^?1 and from 0.0012 to 0.1643?cm³?g^?1, respectively. A pseudo-second-order model was fit with the kinetic data and the results indicate chemical adsorption. The maximum adsorption capacity of activated carbon was 181.82?mg?g^?1 at 25°C according to Langmuir isotherm model.     

Adsorption of urea onto granular activated alumina: A comparative study with granular activated carbon

ABSTRACT

This study investigated the ability of granular activated alumina to remove urea from wastewater through adsorption, and compared its performance with granular activated carbon. XRF, EDX, XRD, and TGA were used to investigate the adsorbents. The removal of urea as a function of pH value was studied. The point of zero charge for activated alumina was found to be 8.8, while that for activated carbon was found to be 7.1. The experimental data of the adsorption process were explored by fitting to different kinetic models to determine the adsorption kinetics and mechanisms. Then, the equilibrium data were examined by fitting to various two-parameter and three-parameter isotherm models. Results showed that the removal efficiency increased with the increasing pH value. The maximum removal efficiencies were 24% and 31% for granular activated alumina and granular activated carbon, respectively, at pH?=?9.0. Kinetic studies showed that adsorption of urea onto both activated alumina and activated carbon can be expressed by pseudo second order kinetics. Equilibrium studies showed that the adsorption isotherms could be expressed by the Redlich-Peterson isotherm and Temkin isotherm for activated alumina and activated carbon, respectively. Adsorbents were investigated using FTIR and SEM, and results showed the occurrence of adsorption.     

Liquid phase adsorption of Congo red dye on functionalized corn cobs

This study investigates the adsorption of Congo red (CR) dye onto corn cob based activated carbon (CCAC) in the batch process. The activated carbon was characterized using FTIR, SEM, and EDX techniques, respectively. The effect of operational parameters such as the initial dye concentration (10–50?mg/L), contact time (5–160 minutes), and solution temperature (30–50°C) were studied. The amount of the CR dye adsorbed was found to increase as these operational parameters increased. Kinetic data for CR dye adsorption onto CCAC were best represented by the pseudo second-order kinetic model. Four different isotherms namely Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich models were used to test the adsorption data. It fitted the Langmuir isotherm model most. Thermodynamic parameters such as ΔH⁰, ΔS⁰, and ΔG⁰ were evaluated. The adsorption process was found to be exothermic and spontaneous. The study shows that CCAC is an effective adsorbent for the adsorption of CR dye from aqueous solution.     

Adsorption equilibria of proline in hydrophilic interaction chromatography

The adsorption behavior of proline under hydrophilic interaction chromatography conditions was investigated from six aqueous solutions of acetonitrile. Proline adsorption isotherms were recorded at each mobile phase composition by frontal analysis and inverse method. The BET model was found to be the best choice to describe the nonlinear behavior of proline adsorption under hydrophilic interaction chromatography conditions. The adsorption isotherm parameters were derived from two independent parameter estimation methods. The parameters derived from regression analysis of the frontal analysis data and from overloaded elution bands were found to be in good agreement with the excess isotherm of water. The mobile phase composition at which the maximum excess adsorption of water was observed corresponded to the maximum saturation capacity measured for proline.     

Microwave assisted preparation of efficient activated carbon from grapevine rhytidome for the removal of methyl violet from aqueous solution

Grapevine rhytidome (the outer layer of bark on trunk), as an abundant and low-cost precursor, was used to prepare granular activated carbon with high surface area for the removal of methyl violet from aqueous solution. Microwave heating source was used to reduce the treatment time and energy consumption. To optimize the preparation, the effects of the different parameters, such as phosphoric acid concentration, acid/precursor weight ratio, impregnation time, microwave power, radiation time, and oven heating time on the ability of the samples for removal of methyl violet were studied. The obtained activated carbon was characterized by N₂ adsorption/desorption, SAXS, TEM and SEM methods. The adsorption of methyl violet onto the activated carbon was studied from both equilibrium and kinetic point of view and the results were compared with the commercial granular activated carbon. The rate of adsorption onto the prepared activated carbon was faster than commercial activated carbon. Different kinetic models were used to analyze the experimental kinetic data. The obtained activated carbon showed higher adsorption capacity (more than twice) for the adsorption of methyl violet in comparison with the commercial one. The equilibrium data were analyzed using different isotherm models. Adsorption was found to be maximum in the pH range 7-9.     

四苯硼钠在活性炭表面吸附过程的疏水相互作用

In this paper, the adsorption characteristics of sodium tetraphenylborate(NaBPh4) on activated carbon at 298.2,303.2,308.2,313..2 and 323.2 K was studied.The results show that the adsorption isotherm of NaBPh4 on activated carbon at different temperatures could be described using Langrnuir equation. Furthermore, the standard Gibbs energy, enthalpy, entropy and hydrophobic interaction Gibbs energy for the adsorption of NaBPh4 on activated carbon were studied, and the result shows that the hydrophobic interaction of BPh4^- ion plays the most important role for the transfer of NaBPh4 from water to activated carbon surface.     

Elution dynamics of adsorption of Chladon 113 and methyl bromide on active carbons

The elution dynamics of adsorption of Chladon 113 (at high contents of the adsorptive) and methyl bromide on active carbons with different lengths of the layer was studied. The adsorption isotherms were described by the equation of the theory of volume filling of micropores. The elution curves were calculated using the model of the equilibrium adsorption layer. The effective kinetic constant calculated in the framework of the model is 1.5 cm for Chladon 113 at a linear velocity of vapor-air flow of 1250 cm min⁻¹ and 1.0 cm for methyl bromide at the velocity of 700 cm min⁻¹. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1353–1355, July, 1998.     

Non-linear modelling of the adsorption of Indigo Carmine dye from wastewater onto characterized activated carbon/volcanic ash composite

Over the past couple of years, the resurgence of placing an effective and sustainable amendment to combat against the auxiliary industrial entities like Indigo Carmine (IC), remains a highly contested agenda from a global point. The birth of non-linear modelling for these auxiliary entities is also of significant interest in order to avoid loss of some useful information. With the renaissance of activated carbon (AC), the AC prepared from palm kernel shells (PKSAC) and composite prepared by combining the PKSAC and porous volcanic ash (BVA) from the foot of active volcanic mountain of Cameroon will be of significant contribution for ever increasing pollution problems. Non-linear modelling method was used to model the uptake capacity by adsorption process of IC onto PKSAC and PKSAC/BVA composite. Effects of contact time (0–60 min), adsorbent dose, pH of solution and initial dye concentration (10–20 ppm) were studied on the quantity removal of the hazardous IC dye from aqueous solution in a batch experiment. The prepared PKSAC and PKSAC/BVA composite were characterized using Nitrogen adsorption at 77 K (BET), Fourier transform Infrared spectroscopy (FTIR), Sacanning electron microscopy with energy dispersive X Ray (SEM-EDX), and particle size. The optimum IC uptake was 11.025 and 12.642 mg/g for PKSAC and PKSAC/BVA composites adsorbent respectively. Four Isotherms and kinetic non-linear regression models each were used to model the adsorption data. It results that for the isotherm models, the Langmuir and Freundlich isotherm models best fitted the adsorption phenomenon while pseudo-first and pseudo-second order kinetic models well described the adsorption mechanism. Furthermore, the adsorption speed constant (α) of the Elovich kinetic model being higher than the desorption coefficient (β) implies chemisorption was the dominant mechanism in the adsorption process. The composite shows 14.67% higher in retention capacity of the IC dye than the pristine carbon. Conclusively, the expanding of activated carbon/volcanic ash composite represents a potentially viable and powerful tool, leading to the plausible improvement of environmental preservation.     

Choice of Model for Estimation of Adsorption Isotherm Parameters in Gradient Elution Preparative Liquid Chromatography

The inverse method is a numerical method for fast estimation of adsorption isotherm parameters directly from a few overloaded elution profiles and it was recently extended to adsorption isotherm acquisition in gradient elution conditions. However, the inverse method in gradient elution is cumbersome due to the complex adsorption isotherm models found in gradient elution. In this case, physicochemically correct adsorption models have very long calculation times. The aim of this study is to investigate the possibility of using a less complex adsorption isotherm model, with fewer adjustable parameters, but with preserved/acceptable predictive abilities. We found that equal or better agreement between experimental and predicted elution profiles could be achieved with less complex models. By being able to select a model with fewer adjustable parameters, the calculation times can be reduced by at least a factor of 10.

     

介孔碳CMK-3对苯酚的吸附动力学和热力学研究

研究了介孔碳CMK-3对苯酚的吸附性能, 与传统商用活性碳(CAC)进行了比较, 结果表明, CMK-3比CAC的吸附量大、吸附速率快、达到平衡时间短, 是一种较好的吸附剂. 同时探讨了介孔碳CMK-3对苯酚的吸附热力学和动力学特征. CMK-3对苯酚的吸附行为可用Langmuir和Freundlich等温式进行描述, 相关性都较好, 但更符合Freundlich经验公式. 分别采用模拟一阶反应和二阶反应模型考察了吸附动力学, 并计算了这些动力学模型的速率常数. 模拟二级反应模型和实验数据之间有较好的相关性. 分别计算了热力学参数ΔG0, ΔS0和ΔH0, 结果表明, CMK-3对苯酚的吸附过程是吸热和自发的.     

Adsorption of Nitrogen on Silica Gel Over a Large Range of Temperatures

To study the mechanism of physical adsorption of supercritical gases, the adsorption equilibria of N₂ on silica gel for 103–298 K using 20 K increments and pressures up to 10 MPa were measured. A transition of the adsorption mechanism was proven on crossing the critical temperature, but the transition way observed is different from that observed with activated carbon. This causes a difference in the locations of the linear section of the n- _g isotherm at the near-critical temperature. Although the isotherm type is different on silica gel and on activated carbon in the sub-critical region, all isotherms in the supercritical region can be well modeled by a single model. It leads to the argument that the adsorption mechanism of supercritical gases is identical no matter what kind of adsorbent is used.     

Synthesis of Porous Material from Coal Gasification Fine Slag Residual Carbon and Its Application in Removal of Methylene Blue

A large amount of coal gasification slag is produced every year in China. However, most of the current disposal is into landfills, which causes serious harm to the environment. In this research, coal gasification fine slag residual carbon porous material (GFSA) was prepared using gasification fine slag foam flotation obtained carbon residue (GFSF) as raw material and an adsorbent to carry out an adsorption test on waste liquid containing methylene blue (MB). The effects of activation parameters (GFSF/KOH ratio mass ratio, activation temperature, and activation time) on the cation exchange capacity (CEC) of GFSA were investigated. The total specific surface area and pore volume of GSFA with the highest CEC were 574.02 m²/g and 0.467 cm³/g, respectively. The degree of pore formation had an important effect on CEC. The maximum adsorption capacity of GFSA on MB was 19.18 mg/g in the MB adsorption test. The effects of pH, adsorption time, amount of adsorbent, and initial MB concentration on adsorption efficiency were studied. Langmuir isotherm and quasi second-order kinetic model have a good fitting effect on the adsorption isotherm and kinetic model of MB.     

Kinetics of salicylic acid adsorption on activated carbon

The adsorption and desorption of salicylic acid from water solutions was investigated in HPLC microcolumns packed with activated carbon. The adsorption isotherm was obtained by the step-up frontal analysis method in a concentration range of 0-400 mg/L and was well fitted with the Langmuir equation. The investigation of rate aspects of salicylic acid adsorption was based on adsorption/desorption column experiments where different inlet concentrations of salicylic acid were applied in the adsorption phase and desorption was conducted with pure water. The concentration profiles of individual adsorption/desorption cycles data were fitted using several single-parameter models of the fixed-bed adsorption to assess the influence of different phenomena on the column behavior. It was found that the effects of axial dispersion and extraparticle mass transfer were negligible. A rate-determining factor of fixed-bed column dynamics was the kinetics of pore surface adsorption. A bimodal kinetic model reflecting the heterogeneous character of adsorbent pores was verified by a simultaneous fit of the column outlet concentration in four adsorption/desorption cycles. The fitted parameters were the fraction of mesopores and the adsorption rate constants in micropores and mesopores, respectively. It was shown that the former rate constant was an intrinsic one whereas the latter one was an apparent value due to the effects of pore blocking and diffusional hindrances in the micropores.