Analyses of gibberellins in coconut (Cocos nucifera L.) water by partial filling-micellar electrokinetic chromatography-mass spectrometry with reversal of electroosmotic flow

In this paper, we present the results of simultaneous screening of eight gibberellins (GAs) in coconut (Cocos nucifera L.) water by MEKC directly coupled to ESI-MS detection. During the development of MEKC-MS, partial filling (PF) was used to prevent the micelles from reaching the mass spectrometer as this is detrimental to the MS signal, and a cationic surfactant, cetyltrimethylammonium hydroxide, was added to the electrolyte to reverse the EOF. On the basis of the resolution of the neighboring peaks, different parameters (i.e., the pH and concentration of buffer, surfactant concentrations, length of the injected micellar plug, organic modifier, and applied separation voltage) were optimized to achieve a satisfactory PF-MEKC separation of eight GA standards. Under optimum conditions, a baseline separation of GA standards, including GA1, GA3, GA5, GA6, GA7, GA9, GA12, and GA13, was accomplished within 25 min. Satisfactory results were obtained in terms of precision (RSD of migration time below 0.9%), sensitivity (LODs in the range of 0.8-1.9 microM) and linearity (R2 between 0.981 and 0.997). MS/MS with multiple reaction monitoring (MRM) detection was carried out to obtain sufficient selectivity. PF-MEKC-MS/MS allowed the direct identification and confirmation of the GAs presented in coconut water (CW) sample after SPE, while, the quantitative analysis of GAs was performed by PF-MEKC-MS approach. GA1 and GA3 were successfully detected and quantified in CW. It is anticipated that the current PF-MEKC-MS method can be applicable to analyze GAs in a wide range of biological samples.     

Analysis of cytokinin nucleotides in coconut (Cocos nucifera L.) water using capillary zone electrophoresis-tandem mass spectrometry after solid-phase extraction

A method based on solid-phase extraction (SPE) and capillary zone electrophoresis-tandem mass spectrometry (CZE-MS/MS) is described for the separation and determination of six cytokinin nucleotides in coconut water. The best CZE separation for the six cytokinin nucleotide standards was achieved using a 25 mM ammonium formate/formic acid buffer (pH 3.8) and 2% (v/v) methanol with an applied gradient separation voltage (25 kV for 32 min, and then a linear gradient to 30 kV in 5 min, finally 30 kV to the end of separation) in less than 60 min. MS/MS with multiple reaction monitoring (MRM) detection was carried out to obtain sufficient selectivity and sensitivity for the cytokinin nucleotides. The combined use of on-line sample stacking and CZE-MS/MS achieved limits of detection (LODs) in the range of 0.06-0.19 microM for the six cytokinin nucleotides at a signal-to-noise ratio of 3. Furthermore, a novel dual-step SPE procedure was developed for the pre-concentration and purification of cytokinin nucleotides using Oasis HLB and Oasis MAX cartridges. The recoveries of the cytokinin nucleotides after the dual-step SPE were in the range of 44-71%. The combination of off-line SPE, on-line sample stacking and CZE-MS/MS approach was successfully applied to screen for endogenous cytokinin nucleotides present in coconut water sample. trans-Zeatin riboside-5'-monophosphate (ZMP) was detected and quantified in coconut water by CZE-MS/MS after SPE and on-line sample stacking.     

Determination of tobacco-specific N-nitrosamines in rabbit serum by capillary zone electrophoresis and capillary electrophoresis-electrospray ionization-mass spectrometry with solid-phase extraction

In this paper, we propose a new strategy for separation and determination of tobacco-specific N-nitrosamines (TSNAs), a group of strong carcinogens found only in tobacco products, by using CZE and CE-MS associated with SPE. Six TSNAs: N'-nitrosonornicotine, N'-nitrosoanatabine, N'-nitrosoanabasine, 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone, 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol, and 4-(methylnitrosamino)-4-(3-pyridyl)-1-butanol were simultaneously separated by either of two CZE methods, one of which worked with ammonium formate buffer (pH 2.5) and another with citrate buffer (pH 2.4), as well as a CE-MS method. The CZE conditions including pH and concentration of running buffer, capillary length, applied voltage, and capillary temperature were systematically optimized. For CE-MS method, an optimized sheath liquid consisted of methanol-water was used at a flow rate of 10 muL/min. With SPE procedure, our proposed CE-MS method was successfully applied to determine TSNAs after 15 min metabolism in rabbits. A comparison study between CZE and CE-MS methods for quantitative purposes was carried out, showing that both methods provided similar separation efficiency, selectivity, repeatability, linearity, and recovery. However, CE-MS method was better suited for the analysis of TSNAs in complicated biological samples for its sensitivity and extra information on molecular structure. Having good accordance with our previous work by using LC-MS, the new CE-MS method is expected to be an alternative to the LC-MS method and applied to study the metabolism of TSNAs.     

Analysis of some cytokinins in coconut (Cocos nucifera L.) water by micellar electrokinetic capillary chromatography after solid-phase extraction

Micellar electrokinetic capillary chromatography (MECC) was developed for the separation of cytokinins including trans-zeatin, trans-zeatin-O-glucoside, dihydrozeatin, dihydrozeatin-O-glucoside, meta-topolin riboside, N6-isopentenyladenine and N6-benzylaminopurine. Under the optimum conditions, i.e. a combination of 10 mM phosphate and 10 mM borate as the running buffer containing 50 mM sodium dodecyl sulphate at pH 10.4, the separation of seven cytokinin standards was accomplished within 11 min. The C18 solid-phase extraction (SPE) method was used to pre-concentrate the putative cytokinins present in the coconut water. Following which, the eluate was further purified using mixed mode Oasis MCX SPE columns and this additional step helps to reduce matrix interference during MECC. After the two solid-phase extraction steps, the optimized MECC method was able to screen for certain cytokinins (zeatin-O-glucoside and dihydrozeatin-O-glucoside) present in coconut water. After this screening, the presence of zeatin-O-glucoside and dihydrozeatin-O-glucoside in coconut water was further confirmed by independent high-performance liquid chromatography and liquid chromatography-mass spectrometry experiments.     

Determination of cytokinins in coconut (Cocos nucifera L.) water using capillary zone electrophoresis-tandem mass spectrometry

The applicability of CZE in combination with MS and MS/MS methods for the simultaneous separation and determination of 12 cytokinins was investigated for the first time. Cytokinins were first completely separated by CZE within less than 20 min using a volatile buffer and then detected directly by MS or MS/MS. Satisfactory separation of the 12 cytokinin standards was achieved using a 25 mM ammonium formate/formic acid buffer (pH 3.4) and 3% ACN v/v with a separation voltage of 25 kV. On the basis of the resolution of the neighboring peaks, the various parameters for CZE-MS optimization, such as buffer pH value, concentration of buffer and organic modifier, applied voltage and sheath liquid, were evaluated systematically. MS/MS with multiple reaction monitoring detection was carried out to obtain sufficient selectivity and sensitivity. The combination of on-line sample stacking and CZE-MS/MS achieved a detection limit in the range of 0.05-0.18 microM for the 12 cytokinins at an S/N of 3. The optimized CZE-MS/MS method was simple, rapid, low cost, robust and highly selective. Furthermore, the developed method was successfully applied to screen for endogenous cytokinins in purified coconut water extract sample. Nine cytokinins were detected and quantified in coconut water after SPE.     

Determination of drug residues in water by the combination of liquid chromatography or capillary electrophoresis with electrospray mass spectrometry

Methods for the determination of drug residues in water have been developed based on the combination of liquid chromatography (LC) or capillary electrophoresis (CE) with mass spectrometry (MS). For HPLC-MS two types of interfaces (pneumatically assisted electrospray ionization interface or an atmospheric pressure chemical ionization interface, respectively) were employed and compared in terms of detection limits. 2 mM Ammonium acetate at pH 5.5 and a methanol gradient was used for the HPLC-MS allowing the separation of a number of drugs such as paracetamol, clofibric acid, penicillin V, naproxen, bezafibrate, carbamazepine, diclofenac, ibuprofen and mefenamic acid. A 20 mM ammonium acetate solution, pH 5.1 was employed for the separation of clofibric acid, naproxen, bezafibrate, diclofenac, ibuprofen and mefenamic acid by CE-MS. Sample pretreatment was performed by solid-phase extraction (SPE) for HPLC-MS or by a combination of liquid-liquid extraction and SPE for CE-MS. The applicability of both the HPLC-MS and CE-MS method was demonstrated for several river water samples.     

Separation of antidepressants by capillary electrophoresis with in-line solid-phase extraction using a novel monolithic adsorbent

The separation of three selective serotonin reuptake inhibitors (SSRIs) by capillary electrophoresis (CE) with fully integrated solid-phase extraction (SPE) is described. Polymeric monolithic SPE modules were prepared in situ within a fused silica capillary from either butyl methacrylate-co-ethylene dimethacrylate or 3-sulfopropyl methacrylate-co-butyl methacrylate-co-ethylene dimethacrylate. Using a 1 cm SPE module placed at the inlet of the capillary, a mixture of sertraline, fluoxetine and fluvoxamine was extracted from aqueous solution by applying a simple pressure rinse. Under pressure-driven conditions, efficient elution was possible from both SPE materials investigated using 50 mM phosphate buffer, pH 3.5 in acetonitrile (20/80, v/v). Two different strategies were investigated for the efficient elution and subsequent CE separation. Injection of an aqueous sample plug directly into the non-aqueous elution/separation buffer was found to be unsuitable with poor elution profiles observed in the electrodriven mode. Alternatively, a sample plug equivalent to several capillary volumes could be injected by pressure followed by filling the capillary with the non-aqueous elution/separation buffer from the outlet end using a combination of pressure and electrodriven flow. Using a neutral monolith, efficient elution/separation was not possible due to an unstable electroosmotic flow (EOF), however, by adding the ionisable monomer, 3-sulfopropyl methacrylate to the SPE module to increase and stabilise the EOF, it was possible to achieve efficient elution from the SPE module, followed by baseline separation by CE using a 200 mM acetate buffer, pH 3.5 in acetonitrile (10/90, v/v). With enrichment factors of over 500 achieved for each of the analytes this demonstrates the potential of in-line SPE-CE for the sensitive analysis of these drugs.     

Capillary electrophoresis-mass spectrometry of intact basic proteins using Polybrene-dextran sulfate-Polybrene-coated capillaries: System optimization and performance

A capillary electrophoresis-mass spectrometry (CE-MS) method using sheath liquid electrospray ionization interfacing was studied and optimized for the analysis of intact basic proteins. To prevent protein adsorption, capillaries with a noncovalent positively charged coating were utilized. Capillaries were coated by subsequent rinsing with solutions of Polybrene, dextran sulfate and Polybrene. The coating proved to be fully compatible with MS detection, causing no background signals and ionization suppression. The composition of the sheath liquid and BGE was optimized using the model proteins α-chymotrypsinogen A, ribonuclease A, lysozyme and cytochrome c. A sheath liquid of isopropanol-water-acetic acid (75:25:0.1, v/v/v) at 2 μL min⁻¹ resulted in optimal signal intensities for most proteins, but caused dissociation of the heme group of cytochrome c. Optimum protein responses were obtained with a BGE of 50 mM acetic acid (pH 3.0), which allowed a baseline separation of the test protein mixture. Several minor impurities present in the mixture could be detected and provisionally identified using accurate mass and a protein modification database. The selectivity of the CE-MS system was investigated by the analysis of acetylated lysozyme. Eight highly related species, identified as non-acetylated lysozyme and lysozyme acetylated in various degrees, could be distinguished. The CE-MS system showed good reproducibility yielding interday (three weeks period) RSDs for migration time and peak area within 2% and 10%, respectively. With the CE-MS system, determination coefficients (R²) for protein concentration and peak area were higher than 0.996, whereas detection limits were between 11 and 19 nM.     

Analysis of positional isomers of hydroxylated aromatic cytokinins by micellar electrokinetic chromatography

A micellar electrokinetic chromatography (MEKC) method was developed for the separation of six positional isomers of hydroxylated aromatic cytokinins (topolin and topolin riboside), including ortho-topolin, meta-topolin, para-topolin, ortho-topolin riboside, meta-topolin riboside, and para-topolin riboside. Optimum resolution and analysis time (ca. 20 min) for the six aromatic cytokinin standards were achieved with a running buffer at pH 8.0 consisting of 20 mM boric acid, 50 mM sodium dodecyl sulfate (SDS), and 20% v/v methanol. The method has good reproducibility and has been successfully applied to detect the presence of a putative ortho-topolin in coconut water extract sample purified using C(18) and mixed-mode solid-phase extraction (SPE) columns. Other advantages of this MEKC method are short analysis time, low solvent consumption, and separation of positional isomers which could be achieved by a simple aqueous buffer system without the use of expensive chromatographic columns. In addition, a high-performance liquid chromatography (HPLC) method with baseline separation of the six topolin and topolin riboside standards was developed for the confirmation of the endogenous ortho-topolin in coconut water sample. Finally, the presence of ortho-topolin was further confirmed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) based on its characteristic fragmentation pattern.     

Optimization of capillary electrophoretic-electrospray ionization-mass spectrometric analysis of catecholamines

The capillary electrophoretic-mass spectrometric analysis (CE-MS) of catecholamines was optimized with coaxial sheath flow interface and electrospray ionization (ESI). The parameters studied included the sheath liquid composition and its flow rate, separation conditions in ammonium acetate buffer together with the ESI and cone voltages as mass spectrometric parameters. In addition, the effect of ESI voltage on injection as well as the siphoning effect were considered. The optimized conditions were a sheath liquid composition of methanol-water (80:20 v/v) with 0.5% acetic acid, with a flow rate of 6 microL/min. The capillary electrophoretic separation parameters were optimized with 50 mM ammonium acetate buffer, pH 4.0, to +25 kV separation voltage together with a pressure of 0.1 psi. The most intensive signals were obtained with an ESI voltage of +4.0 kV and a cone voltage of +20 V. The nonactive ESI voltage during injection as well as avoidance of the siphoning effect increased the sensitivity of the MS detection considerably. The use of ammonium hydroxide as the CE capillary conditioning solution instead of sodium hydroxide did not affect the CE-MS performance, but allowed the conditioning of the capillary between analyses to be performed in the MS without contaminating the ion source.     

Solid-phase extraction for metabolomic analysis of high-salinity samples by capillary electrophoresis-mass spectrometry

Environmental samples such as soil solutions contain inorganic ions such as NH4(+), K(+), Na(+), NO3(-), and PO4(3-) in high concentrations, which must be removed prior to capillary electrophoresis-mass spectrometry analysis to obtain accurate results. However, the separation of these inorganic ions from ionic metabolites, which are the target compounds in capillary electrophoresis-mass spectrometry analysis, is difficult because the physicochemical properties of the inorganic ions are similar to those of the ionic metabolites. In this study, we used various solid-phase extraction (SPE) columns for the purification of the samples containing inorganic ions in high concentrations. We found that cation-exchange SPE columns successfully filtered out the inorganic ions while retaining most of the organic compounds, which were easily collected with high recovery rates. In addition, 17 cationic metabolites in the soil solution were quantified by CE-MS analysis following the SPE purification process. The results suggest that our method can be used to analyze other environmental samples containing inorganic ions in high concentrations.     

Analyzing small samples with high efficiency: capillary batch injection–capillary electrophoresis–mass spectrometry

We present an experimental approach to conducting fast capillary electrophoresis-mass spectrometry (CE-MS) measurements of very small samples in the nanoliter range. This is achieved by injecting sample very efficiently into a CE-MS system. Injection efficiency represents the ratio of injected sample to the amount of sample needed for carrying out the injection process (v/v). In order to increase this injection efficiency from typical values of 10(-3) to 10(-7), the concept of capillary batch injection is used to build an automated, small-footprint injection device for CE-MS. This device is capable of running true multi-sample measurement series, using minimal sample volumes and delivering an injection efficiency of up to 100?%. It is compatible with both aqueous and non-aqueous background electrolytes. As an additional benefit, CE-MS separations of a catecholamine model system in capillaries of 15?cm length under conditions of high electric field strength could be accomplished in 20?s with high separation efficiency. This report details design and specifications of the injection device and shows optimal parameter choices for injections with both high injection efficiency and high separation efficiency. Furthermore, a procedure is presented to coat the tip of a fused silica capillary with a silicone elastomer which acts as a seal between two capillaries.     

Determination of sulfophenyl carboxylic acids in agricultural groundwater samples by CE with ultraviolet absorption detection

An analytical method for the determination of six sulfophenyl carboxylic acids, namely (p-sulfophenyl)acetic, 2-(p-sulfophenyl)propionic, 2-(p-sulfophenyl)butyric, 3-(p-sulfophenyl)butyric, 4-(p-sulfophenyl)butyric, and 5-(p-sulfophenyl)valerianic acid, in agricultural irrigation water samples was developed. It involves an SPE procedure, an on-line preconcentration normal stacking mode and subsequent separation and determination using CE with UV detection (CE-UV). p-Sulfobenzoic acid was used as internal standard. The compounds were separated with an uncoated capillary and a 25 mM ammonium acetate/acetic acid buffer solution (pH 5.5) with 2-propanol (30% v/v) and 0.75 mM CTAB. Analyses were run at -25 kV, 25 degrees C, and 100 s of hydrodynamic injection with UV detection at 225 nm. Quantification limits found ranged between 4 and 6 ng/mL. The proposed method was validated using a recovery assay. It was satisfactorily used for the determination of these compounds in groundwater samples to track down the biodegradation of linear alkylbenzene sulfonates in an agricultural soil from the fertile plain of Granada (Spain).     

Determination of bupivacaine and metabolites in rat urine using capillary electrophoresis with mass spectrometric detection

A method using capillary electrophoresis-mass spectrometry (CE-MS) was developed for the structural elucidation of bupivacaine and metabolites in rat urine. Prior to CE-MS analysis, solid-phase extraction (SPE) was used for sample cleanup and preconcentration purposes. Exact mass and tandem mass spectrometric (MS/MS) experiments were performed to obtain structural information about the unknown metabolites. Two instruments with different mass analyzers were used for mass spectrometric detection. A quadrupole time-of-flight (Q-TOF) and a magnetic sector hybrid instrument were coupled to CE and used for the analysis of urine extracts. Hydroxybupivacaine as well as five other isomerically different metabolites were detected including methoxylated bupivacaine.     

Simultaneous determination of different classes of antibiotics in fish and livestock by CE-MS

A specific CE-MS method was developed for the simultaneous determination of 12 antibacterial residues (four sulfonamides: sulfamethazine, sulfathiazole, sulfadiazine, and sulfachlorpyridazine; four beta-lactams: amoxicillin, ampicillin, oxacillin, and penicillin V, and four quinolones: danofloxacin, enrofloxacin, ofloxacin, and flumequine) in fish and livestock. Separation conditions, sheath liquid composition and electrospray parameters were optimized to obtain adequate CE separation and a high sensitivity. CE employed a 75 cm long fused-silica capillary (50 cm thermostated plus 25 cm at room temperature) 75 microm id and a 60 mM ammonium acetate separation buffer at pH 8 with 10% of methanol. The minimum number of identification points, according to the 2002/657/EC European Decision, was achieved using an IT in multiple reaction monitoring (MRM) mode. For quantification in meat and fish samples, a two-step procedure was developed using ACN to extract the antibacterials and to precipitate the proteins and dispersive SPE, with C18 to clean up the extract. External matrix matched calibration curves were used to achieve accurate quantitative results. The LODs and LOQs (below 18 and 50 ng/kg, respectively) were in all cases lower than the maximum residue limits for these compounds in meat and fish. The recoveries ranged from 78 to 97% and the precision with RSDs lower than 18% indicate the potential of CE-MS for the analysis of multiclass antibacterial residues in food. The method was applied to meat and fish samples taken from markets, slaughterhouses, and fish farms.     

在线固相萃取-毛细管高效液相色谱联用测定奶酪中的生物胺

采用双二元泵毛细管液相色谱,通过六通阀实现了样品的在线净化与分离定量的自动切换,建立了同时测定奶酪中的15种生物胺的在线固相萃取-毛细管高效液相色谱联用方法。通过优化毛细管高效液相色谱的分离条件,考察在线固相萃取流动相的组成、上样溶液pH值以及六通阀的切换时间对生物胺回收率的影响,确定最佳分析条件为：5%乙腈-水作为固萃柱(Zorbax SB-C18)的流动相,上样溶液pH=11,上样3 min后切换六通阀。采用内标法定量,15种生物胺标准曲线的线性范围为0.25~50.0 mg/L,检出限( LOD)为0.05~0.25 mg/L,定量限(LOQ)为0.15~0.80 mg/L。除了甲胺、乙胺、3-甲基丁胺和5-羟基色胺外,其余生物胺的不同添加水平(1,20和40 mg/kg)下的加标回收率为79.6%~118.7%;除3-甲基丁胺和5-羟基色胺外,其余生物胺的RSD在0.3%~14.9%之间,可用于奶酪中多种生物胺的快速检测。     

Nonaqueous capillary electrophoresis method for the analysis of gleevec and its main metabolite in human urine

The viability of nonaqueous capillary electrophoresis (NACE) was investigated for determination of gleevec and its main metabolite in human urine using a fused-silica capillary. Baseline separation of the studied solutes was obtained using a nonaqueous solution composed of 12 mM ammonium acetate and 87.6 mM acetic acid in methanol-acetonitrile (ACN) (80:20, v:v) providing analysis time shorter than 3 min. Different aspects including stability of the solutions, linearity, accuracy and precision were studied in order to validate the method in the urine matrix. Detection limits of 24 microg L(-1) for gleevec and its metabolite were obtained. A robustness test of the method was carried out using the Plackett-Burman fractional factorial model with a matrix of 15 experiments. The developed method is simple, rapid and sensitive and has been used to determine gleveec and its metabolite at clinically relevant levels in human urine. Before NACE determination, a solid-phase extraction (SPE) procedure with a C18 cartridge was necessary. Real determination of these analytes in two patient urines were done.     

Screening and analytical confirmation of sulfonamide residues in milk by capillary electrophoresis-mass spectrometry

A new methodology is proposed to automate the monitoring of sulfonamide residues in milk samples. It combines a screening unit for the total amount of sulfonamide with capillary electrophoresis-mass spectrometry (CE-MS) equipment for processing the samples containing a detectable level of sulfonamide. The screening unit consists of continuous-flow system (CFS) to precipitate the proteins connected on-line to the CE-MS equipment, in which a common characteristic ion of all sulfonamides was monitored with the MS detector by flushing the sample through the capillary. The confirmatory method is based on the purification and preconcentration of sulfonamides in a CFS unit and posterior analysis by CE-MS. The sample treatment unit was also on-line connected to the CE-MS equipment. In order to increase sensitivity, the flow rate of the sheath liquid was diminished from 0.5 to 0.2 microL.min(-1) by increasing the content in water from 0 to 50% and the formic acid from 0.5 to 1.5% in this liquid and by applying an overimposed pressure of 5 mbar during the electrophoretic separation. The method allowed the analysis of 30 samples per hour.     

Determination of five priority haloacetic acids by capillary electrophoresis with contactless conductivity detection and solid phase extraction preconcentration

A sensitive capillary electrophoretic separation method with contactless conductivity detection (C4D) for analysis of five priority haloacetic acids (HAA5) is presented. The analytes were baseline separated in an electrolyte composed of 20 mM 2-(N-Morpholino) ethanesulfonic acid (MES), 20 mM L-histidine (HIS), and 30 μM cetyltrimethylammonium bromide (CTAB) at pH 6.0 in less than 4 min. A simplified solid-phase extraction (SPE) preconcentration procedure on highly cross-linked polystyrene-divinylbenzene (PS-DVB) type sorbent was developed and optimized with respect to short preconcentration time. HAA5 from a 25-mL sample aliquot of tap and swimming pool water could be preconcentrated in less than 5 min using an in-house made SPE column with recoveries ranging from 23 to 98%. Combining the SPE preconcentration procedure with capillary electrophoretic analysis, the attained limits of detection were between 6.1 and 12.2 μg/L with total analysis time of less than 10 min.     

A capillary zone electrophoresis for determination of thiolic peptides in biological samples

A new method to improve the analyses of thiolic peptides (cysteine, γGlu-Cys, glutathione, phytochelatins and desglycyl-phytochelatins) derivatized with monobromobimane (mBrB) in complex biological samples by CZE is described. The method involves a SPE using Sep-Pak Light C18 Cartridges after derivatization and a later CZE analysis. Elution of mBrB-thiols was achieved with 10 mM HCl + 70% methanol v/v in deionised water. Electrophoretic parameters, such as BGE pH and concentration, different organic additives (methanol and trifluoroethanol), applied voltage and capillary length were studied in order to establish suitable analytical conditions. Optimum separation of the mBrB-thiolic peptides was obtained with 100 mM sodium borate buffer at pH 7.60. The electrophoretic conditions were +15 kV, capillary length of 90 cm from inlet to detector (98 cm total length, 50 μm ID), samples were loaded into the capillary by hydrodynamic injection (50 mbar, 20 s) and detection was performed at 390 nm. The improved method showed good reproducibility, linearity and sensitivity. The LODs and LOQs estimated using a standard of GSH were 1.41 and 4.69 μM respectively.