简单方法制备羟基磷灰石中空微球

无需添加任何有机物和金属离子, 以易得的中空球形碳酸钙(CaCO3)与磷酸氢二钠(Na2HPO4)作为反应物在常压下制备出羟基磷灰石中空微球. 通过场发射扫描电子显微镜(FESEM)、扫描电子显微镜(SEM), X射线粉末衍射(XRD)等手段对制备的羟基磷灰石中空微球的结构、组成和形貌进行了表征, 考察了不同反应温度对中空球形貌的影响. 实验结果表明, 所制备的羟基磷灰石微球是由短针状的纳米粒子组成的, 直径为2-4 μm. 对反应机理进行了初步探讨.     

Synthesis and evolution of PbS nanocrystals through a surfactant-assisted solvothermal route

We present a surfactant-assisted solvothermal approach for the controllable synthesis of a PbS nanocrystal at low temperature (85 degrees C). Nanotubes (400 nm in length with an outer diameter of 30 nm), bundle-like long nanorods (about 5-15 mum long and an average diameter of 100 nm), nanowires (5-20 mum in length and with a diameter of 20-50 nm), short nanorods (100-300 nm in length and an axial ratio of 5-10), nanoparticles (25 nm in width with an aspect ratio of 2), and nanocubes (a short axis length of 10 nm and a long axis length of 15 nm) were successfully prepared and characterized by transmission electron microscopy, scanning electron microscopy, and powder X-ray diffraction pattern. A series of experimental results indicated that several experimental factors, such as AOT concentration, ratio of [water]/[surfactant], reaction time, and ratio of the reagents, play key roles in the final morphologies of PbS. Possible formation mechanisms of PbS nanorods and nanotubes were proposed.     

A solid-state NMR investigation of the structure of nanocrystalline hydroxyapatite

Nanocrystalline hydroxyapatite (HAp) prepared by a precipitation route was investigated. The X-ray diffraction (XRD) powder patterns of the elongated nanocrystals with a typical diameter of about 10 nm and length of 30-50 nm (by transmission electron microscopy (TEM)) revealed the presence of HAp with significantly broadened XRD reflections. However, Ca deficiency was found, as the Ca/P ratio was 1.5 only (so-called calcium-deficient hydroxyapatite (CDHA)), and not 1.67. This Ca deficiency of nanocrystalline HAp is explained using NMR. It is shown unambiguously that (i) the nanocrystals consist of a crystalline core and a (disordered) surface region with a relative phosphate content of about 1:1, (ii) the crystalline core is HAp, and (iii) the surface region is dominated by hydrogen phosphate anions (with no hydroxyapatite-like structural motif) and structural water (hydrate). From the relative phosphate content and taking into account the crystal shape, the thickness of the surface layer along the main crystal axis could be estimated to be about 1 nm, and the average chemical composition of the surface layer has been determined. Finally, a Ca/P ratio of 1.52 was estimated from the NMR data that compares well with the value of 1.51 from chemical analysis. The important consequences are that the surface of nanocrystalline HAp has nothing in common with the bulk composition and that the chemistry of such materials (e.g. the binding of protein molecules to phosphate surfaces) must be reconsidered.     

Supramolecular nano networks formed by molecular-recognition-directed self-assembly of ditopic calix[5]arene and dumbbell [60]fullerene

Dumbbell fullerene 1 and ditopic bisdouble-calix[5]arene 2 were synthesized. Their iterative host-guest complexations create the supramolecular nano network. Scanning electron microscopy revealed the formation of the branched fiber, possessing a length of more than 100 mum and widths of 250-500 nm on a glass plate. More detailed information was given by atomic force microscopy. The formed fibers on a mica plate have widths of 60-90 nm and heights of 1.2-1.9 nm. The nanosize assemblies are probably composed of a bundle of 40-60 polymer chains created by entangling the alkyl side chains with van der Waals interaction.     

Surface modification of hydroxyapatite nanocrystals by grafting polymers containing phosphonic acid groups

A novel approach for the surface modification of hydroxyapatite (HAp) nanocrystals is described by grafting polymerization of vinyl phosphonic acid (VPA) using a redox initiating system in an aqueous media. Fourier transform infrared (FT-IR) and XRD analyses confirmed the modification reaction on HAp surfaces. Inductively coupled plasma mass spectroscopy (ICP MS) showed that the Ca/P molar ratio decreased from 1.67 to 1.36 with increasing the feed VPA amount. Zeta potentials of unmodified HAp and modified HAp in phosphate-buffered saline (PBS) solutions (pH 7.4, ionic strength = 10 mM) were negative and decreased with increasing the amount of grafted PVPA. Transmission electron microscopy (TEM) measurements and time-dependent phase monitoring indicated that the colloidal stability of modified HAp over unmodified HAp in water dramatically increased and tended to exist as single nanocrystals without aggregation.     

Self-assembled structures of hydroxyapatite in the biomimetic coating on a bioinert ceramic substrate

The tribological properties of alumina ceramic are excellent due in part to a high wettability because of the hydrophilic surface and fluid film lubrication that minimizes the adhesive wear. Such surfaces are further modified with bioactive glass/ceramic coating to promote direct bone apposition in orthopedic applications. The present communication reports the biomimetic coating of calcium hydroxyapatite (HAp) on dense (2-3% porosity) alumina (alpha-Al(2)O(3)) substrate (1cmx1cmx0.5cm), at 37 degrees C. After a total period of 6 days immersion in simulated body fluid (SBF), at 37 degrees C, linear self-assembled porous (pore size: approximately 0.2mum) structures (length: approximately 375.39mum and width: 5-6mum) of HAp were obtained. The phenomenon has been demonstrated by self-assembly and diffusion-limited aggregation (DLA) principles. Structural and compositional characterization of the coating was carried out using SEM with EDX facility, XRD and FT-IR data.     

Hydroxyapatite nanoparticles as stimulus-responsive particulate emulsifiers and building block for porous materials

Hydroxyapatite (HAp) nanoparticles with spherical, rod-shaped or fiber-shaped morphologies were synthesized by wet chemical method in aqueous media. Scanning electron microscopy, dynamic light scattering, helium pycnometry, and aqueous electrophoresis techniques were used to characterize the nanoparticles in terms of their particle size and morphology, density and zeta potential, respectively. Stable "Pickering-type" emulsions were prepared using the HAp nanoparticles as a particulate emulsifier and methyl myristate as an oil phase above pH 7.7, but not below pH 6.1. These emulsions were characterized in terms of their emulsion type, mean droplet diameter and morphology using electrical conductivity, light diffraction and optical microscopy. Rapid demulsification could be induced by lowering the solution pH: addition of acid led to dissolution of the HAp nanoparticles attached on oil-water interface and the emulsion was destabilized. HAp nanoparticles precipitated by addition of base to the aqueous phase after demulsification and the HAp particles precipitated worked as an effective particulate emulsifier. This emulsification-demulsification cycle was reversible. Sintering of methyl myristate-in-water emulsion stabilized with the HAp nanoparticles led to a porous HAp material.     

Single‐Crystalline ZnO Nanowire Bundles: Synthesis,Mechanism and Their Application in Dielectric Composites

Single‐crystalline ZnO nanowire bundles have been synthesized in large‐scale by an improved microemulsion method in the presence of excessive hydrate hydrazine and dodecyl benzene sulfonic acid sodium salt (DBS) in xylene. The product is characterized using X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and high‐resolution transmission electron microscopy (HRTEM). The result shows that the bundle is composed by many oriented single‐crystalline ZnO nanowires with a length of about 1 μm and a diameter of about 20–30 nm. The influence of DBS, hydrazine and the reaction time on the morphology of final product and the formation mechanism of such nanostructures were discussed; the application in the dielectric composites is also studied.     

Enhancing the stiffness of electrospun nanofiber scaffolds with a controlled surface coating and mineralization

A new method was developed to coat hydroxyapatite (HAp) onto electrospun poly(lactic-co-glycolic acid) (PLGA) nanofibers for tendon-to-bone insertion site repair applications. Prior to mineralization, chitosan and heparin were covalently immobilized onto the surface of the fibers to accelerate the nucleation of bone-like HAp crystals. Uniform coatings of HAp were obtained by immersing the nanofiber scaffolds into a modified, 10-fold-concentrated simulated body fluid (m10SBF) for different periods of time. The new method resulted in thicker and denser coatings of mineral on the fibers compared to those produced by previously reported methods. Scanning electron microscopy measurements confirmed the formation of nanoscale HAp particles on the fibers. A mechanical property assessment demonstrated a higher stiffness with respect to previous coating methods. A combination of the nanoscale fibrous structure and bonelike mineral coating could mimic the structure, composition, and function of mineralized tissues.     

Effect of temperature on crystallite size of hydroxyapatite powders obtained by wet precipitation process

In this investigation, HAp powders were synthesized using the wet chemical precipitation technique. The temperature of the heat treatment (80 °C, 120 °C, and 160 °C) and the addition of glutamic acid were the considered process parameters. After the reaction between the precursors calcium nitrate [Ca(NO₃)₂] and ammonium phosphate [(NH₄)H₂PO₄], decantation of the residue, drying, and finally, heat treatment of the residue were done sequentially. X-ray diffraction (XRD) analysis, scanning electron microscope (SEM) observations, and X-ray fluorescence (XRF) analysis were carried out to characterize the synthesized HAp powders. It was found that at a high heat treatment temperature plus the addition of glutamic acid are suitable process parameters to acquire uniform HAp powders with plate morphology and fibers with an average particle size of ～100–200 µm. The Ca/P ratio obtained was like the hydroxyapatite present in the bones in the order of 1.72. This situation can be indicated as an essential advantage in the biocompatibility of the synthesized material. The use of glutamic acid suggests crystal growth in a preferential direction as reported in our previous work. The manufacture of hydroxyapatite, especially in powder, is of great interest in developing additive manufacturing systems for the biomedical market.     

Synthesis and characterization of nanocrystalline hydroxyapatite and its catalytic behavior towards synthesis of 3,4‐disubstituted isoxazole‐5(4H)‐ones in water

In the present work, the nanocrystalline particles of hydroxyapatite (HAp) using an easy alkoxide‐based sol–gel technique including triethyl phosphate [PO (OC₂H₅)₃] and Ca (NO₃)₂·4H₂O as P and Ca precursors have been synthesized. The sample characterization was performed by X‐ray diffraction, Fourier transform‐infrared analysis, scanning electron microscopy, thermal analysis (thermogravimetric analysis/differential thermal analysis), and elemental analysis of energy‐dispersive X‐ray analysis. It is interesting that single phase of HAp was obtained at a low firing temperature of 500 ° C. Modified Scherrer equation as the Williamson?Hall method was applied for the measurement of crystallite size distributions and micro‐strain of the sample. The determined crystallite size by complementary technique of transmission electron microscopy has good consistency with those obtained from the Scherrer formula. Moreover, we reported the one‐pot synthesis of 3,4‐disubstituted isoxazole‐5(4H)‐ones through the aqueous solution reaction of three components of ethyl acetoacetate, hydroxylamine hydrochloride and various aromatic aldehydes at room temperature. This protocol offers several advantages, including a simple work‐up procedure, very short reaction times (under 25 min), in accordance with the principles of green chemistry, recyclability, excellent yields (87–98%) and environmentally friendly.     

The fabrication of one-dimensional Ca4Y6(SiO4)6O: Ln3+ (Ln=Eu, Tb) phosphors by electrospinning method and their luminescence properties

One-dimensional Ca(4)Y(6)(SiO(4))(6)O: Ln(3+) (Ln=Eu, Tb) microfibers were fabricated by a simple and cost-effective electrospinning method. X-ray diffraction (XRD) pattern and high-resolution transmission electron microscopy (HRTEM) confirmed that the fibers were composed of hexagonal Ca(4)Y(6)(SiO4)(6)O phase. Thermogravimetric and differential scanning calorimetry (TG-DSC) results showed that the Ca(4)Y(6)(SiO4)(6)O phase began to crystallize at 740°C. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) results indicated that the diameter of as-prepared microfibers ranged from 390 to 900 nm and the diameter of the microfibers annealed at 1000°C ranged from to 120 to 260 nm. Under ultraviolet and low-voltage electron beams (3-5 kV) excitation, the Ca(4)Y(6)(SiO(4))(6)O: Ln(3+) (Ln=Eu, Tb) samples showed the red and green emission, corresponding to (5)D(0)→(7)F(2) transition of Eu(3+) and (5)D(4)→(7)F(5) transition of Tb(3+), respectively.     

Microstructure determination of AOT + phenol organogels utilizing small-angle X-ray scattering and atomic force microscopy.

Dry reverse micelles of the anionic twin-tailed surfactant bis(2-ethylhexyl) sulfosuccinate (AOT) dissolved in nonpolar solvents spontaneously form an organogel when p-chlorophenol is added in a 1:1 AOT:phenol molar ratio. The solvents used were benzene, toluene, m-xylene, 2,2,4-trimethylpentane (isooctane), decane, dodecane, tetradecane, hexadecane, and 2,6,10,14-tetramethylpentadecane (TMPD). The proposed microstructure of the gel is based on strands of stacked phenols linked to AOT through hydrogen bonding. Small-angle X-ray scattering (SAXS) spectra of the organogels suggest a characteristic length scale for these phenol-AOT strands that is independent of concentration but dependent on the chemical nature of the nonpolar solvent used. Correlation lengths determined from the SAXS spectra indicate that the strands self-assemble into fibers. Direct visualization of the gel in its native state is accomplished by using tapping mode atomic force microscopy (AFM). It is shown that these organogels consist of fiber bundle assemblies. The SAXS and AFM data reinforce the theory of a molecular architecture consisting of three length scales-AOT/phenolic strands (ca. 2 nm in diameter) that self-assemble into fibers (ca. 10 nm in diameter), which then aggregate into fiber bundles (ca. 20-100 nm in diameter) and form the organogel.     

Solid-state NMR study of the transformation of octacalcium phosphate to hydroxyapatite: a mechanistic model for central dark line formation

For many years, octacalcium phosphate (OCP) has been postulated as the precursor phase of biological apatite in bones and teeth. In this work, we study the molecular mechanism of OCP to hydroxyapatite (HAp) transformation in vitro by several physical techniques, with particular emphasis on solid-state (31)P homonuclear double-quantum (DQ) NMR spectroscopy. The in vitro system is prepared by mixing urea, sodium phosphate monobasic dehydrate, and calcium nitrate tetrahydrate at 100 degrees C. The images obtained by scanning electron microscopy and transmission electron microscopy show that the bladelike OCP crystals will transform into hexagonal rod-shaped HAp crystals as the pH of the reaction mixture increases slowly from 4.35 to 6.69 in 12 h. Powder X-ray diffraction patterns indicate that a trace amount of monetite was also precipitated when the pH was around 5. Together with computer-assisted lattice matching, our DQ NMR data reveal that OCP crystals transform to HAp topotaxially, where the [000](HAp) and [20](HAp) axes are along the same directions as the [001](OCP) and [010](OCP) axes, respectively. On the basis of our in vitro results, the formation of the central dark line commonly found in biological hard tissues could be explained by the inherent lattice mismatch between OCP and HAp. Furthermore, the data of the (31)P{(1)H} cross-polarization NMR suggest that water molecules enter the hydration layers of OCP crystals via the hydrolysis reaction HPO(4)(2)(-) + OH(-) = PO(4)(3)(-) + H(2)O, which also accounts for the deprotonation of the HPO(4)(2)(-) ions during the transformation.     

Systematic investigation and in vitro biocompatibility studies on mesoporous europium doped hydroxyapatite

This paper reports the systematic investigation of europium doped hydroxyapatite (Eu:HAp). A set of complementary techniques, namely Fourier Transform Infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and the Brunauer-Emmett-Teller (BET) technique were used towards attaining a detailed understanding of Eu:HAp. The XPS analysis confirmed the substitution of Ca ions by Eu ions in the Eu:HAp samples. Secondly, Eu:HAp and pure HAp present type IV isotherms with a hysteresis loop at a relative pressure (P/P₀) between 0.4 and 1.0, indicating the presence of mesopores. Finally, the in vitro biological effects of Eu:HAp nanoparticles were evaluated by focusing on the F-actin filament pattern and heat shock proteins (Hsp) expression in HEK293 human kidney cell line. Fluorescence microscopy studies of the actin protein revealed no changes of the immunolabelling profile in the renal cells cultured in the presence of Eu:HAp nanoparticles. Hsp60, Hsp70 and Hsp90 expressions measured by Western blot analysis were not affected after 24 and 48 hours exposure. Taken together, these results confirmed the lack of toxicity and the biocompatibility of the Eu:HAp nanoparticles. Consequently, the possibility of using these nanoparticles for medical purposes without affecting the renal function can be envisaged.      

Formation of ordered arrays of oriented polyaniline nanoparticle nanorods

We report the preparation of ordered polyaniline (PANI) nanorod arrays in an aqueous medium. The oriented PANI nanorods (80-400 nm in diameter and 8-15 mum in length) were synthesized in the presence of hydrophilic Allura Red AC (ARAC) as the structure-directing agent and ammonium persulfate as an oxidant in HCl solution. The morphologies of the oriented PANI nanoparticle nanorods were confirmed by scanning electron microscopy (SEM) and transmission electron microscopy images, and the effect of reaction conditions on the morphology of PANI nanostructures was also studied. On the basis of the result obtained from small-angle X-ray scattering, we propose that rodlike micelle arrays of ARAC-aniline are responsible for directing the formation of oriented PANI nanoparticle nanorods. SEM images and the data analysis of static and dynamic light scattering give supportive evidence to the formation of the PANI nanoparticle nanorods by an elongation process. The chemical and electronic structures of the PANI nanorods were also studied by Fourier transform IR and UV-vis spectrometries, respectively.     

Synthesis and electrochemical properties of nanostructured LiCoO2 fibers as cathode materials for lithium-ion batteries

Nanostructured LiCoO2 fibers were prepared by the sol-gel related electrospinning technique using metal acetate and citric acid as starting materials. The transformation from the xerogel fibers to the LiCoO2 fibers and the nanostructure of LiCoO2 fibers have been investigated in detail. The LiCoO2 fibers with 500 nm to 2 mum in diameter were composed of polycrystalline nanoparticles in sizes of 20-35 nm. Cyclic voltammetry and charge-discharge experiments were applied to characterize the electrochemical properties of the fibers as cathode materials for lithium-ion batteries. The cyclic voltammogram curves indicated faster diffusion and migration of Li+ cations in the nanostructured LiCoO2 fiber electrode. In the first charge-discharge process, the LiCoO2 fibers showed the initial charge and discharge capacities of 216 and 182 (mA.h)/g, respectively. After the 20th cycle, the discharge capacity decreased to 123 (mA.h)/g. The X-ray diffraction and high-resolution transmission electron microscopy analyses indicated that the large loss of capacity of fiber electrode during the charge-discharge process might mainly result from the dissolution of cobalt and lithium cations escaping from LiCoO2 to form the crystalline Li2CO3 and CoF2 impurities.     

纺锤形介孔纳米二氧化锰的控制合成

在KMnO₄和葡萄糖水溶液体系中, 用一步水热法控制合成了介孔MnCO₃纳米纺锤体, 通过焙烧MnCO₃前驱体可以得到介孔纳米MnO₂, 且保持了原有的纺锤体形貌. 用X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、扫描电镜(SEM)、透射电镜(TEM)和N₂吸附-脱附(BET)对制备的样品进行了形貌和结构的表征. 并对反应时间、反应物浓度等对产物形貌的影响进行了研究. 实验结果表明, 反应时间和葡萄糖的浓度对MnCO₃前驱体的尺寸和形貌具有重要影响, MnCO₃纵横比可从1.35:1到2.89:1之间改变. 并初步探讨了介孔MnO₂纺锤体的生长机制, MnO₂ 孔的形成是由于焙烧葡萄糖降解形成的纳米碳颗粒所致.     

Solvothermal synthesis and characterization of Ln (Eu3+, Tb3+) doped hydroxyapatite

Luminescent Ln (Eu3+, Tb3+) doped hydroxyapatite (Eu:HAp, Tb:HAp) phosphors were successfully fabricated via the cetyltrimethylammonium bromide (CTAB)/n-octane/n-butanol/water microemulsion-mediated solvothermal process. The structure, morphology, and optical properties were systematically characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectra (XPS), Fourier transform infrared spectroscopy (FT-IR), and photoluminescence (PL) spectra as well as the kinetic decays, respectively. The XRD results reveal that the obtained Eu:HAp and Tb:HAp show the characteristic peaks of hydroxyapatite in a hexagonal lattice structure. It is observed that the as-prepared luminescent samples exhibit rod-like morphology with well dispersed and non-aggregated size distribution. Upon excitation by UV radiation, the phosphors demonstrate the characteristic 5D 0-7F 1-4 emission lines of Eu3+ and the characteristic 5D4-7F 3-6 emission lines of Tb3+. Moreover, the photoluminescence intensities (PL) of Eu3+ and Tb3+ can be tuned by altering the solvothermal temperature and the doping concentration of Eu3+ and Tb3+.     

核-壳结构壳聚糖/聚乙烯醇-聚碳酸亚丙酯超细纤维的制备

利用同轴电纺丝技术制备出具有核-壳结构的壳聚糖/聚乙烯醇-聚碳酸亚丙酯电纺丝纤维,考察了溶剂复配对成纤的影响,采用扫描电镜和透射电镜对纤维的形貌、结构、直径分布等进行了探索,并在优化的工艺条件下,将羟基磷灰石负载在内层结构中.研究表明,采用氯仿/N,N-二甲基甲酰胺(1/1)复配溶剂可有效避免聚合物溶液在喷丝口处的凝结现象.同单纺纤维相比,核壳结构的纤维直径分布较宽,纤维壳层和核层界限清晰;红外谱图分析证明羟基磷灰石可负载在纤维的核结构中.