提拉法生长高质量氟化镁单晶

设计了适合提拉法生长氟化镁单晶体的温场,采用提拉法成功生长出了直径100 mm的高质量氟化镁单晶.晶体内无气泡等宏观缺陷、无开裂;通过精密退火处理后,晶体透过率达到95;,平均应力双折射小于0.5 nm/cm.上述结果表明采用提拉法可以生长高质量的氟化镁单晶.     

新型激光基质晶体BaY2F8结晶习性的探索

总结了BaY2F8晶体的结构和性质,利用提拉法实现了BaY2F8晶体的生长,并得到X光衍射和透过率验证.使用的温场梯度为:在r=0,z=0处的径向梯度约为0.26℃/mm,纵向梯度约为27.06℃/mm.为了提高晶体质量,需进一步改进温场,如加大径向梯度、减小纵向梯度,从而有利于熔液径向对流,并降低结晶和生长速度.     

ZnGeP2单晶生长温场研究

根据ZnGeP2(ZGP)晶体的生长特性,自行设计组装了三段式独立控温生长炉,优化了温场分布.采用改进的垂直布里奇曼法成功生长出外观完整、无裂纹的ZGP单晶体,尺寸达15 mm×35 mm.对晶体进行解理实验和X射线衍射分析,发现ZGP晶体易沿(101)面解理,其回摆峰尖锐无劈裂.对未经退火处理的晶片进行红外透过率测试,在2～12 μm波段内红外透过率达45;以上.研究结果表明所设计的温场适合于ZGP单晶生长,生长出的ZGP晶体完整性好、质量较高.     

坩埚下降法生长白宝石晶体的研究

本文报道了坩埚下降法生长大尺寸白宝石单晶.我们使用大尺寸异型钼坩埚,高纯氧化铝原料,在中性气氛下,结晶区温度梯度为25～30℃/cm,生长速度为0.8～1.8mm/h,生长方向选C面[0001]取向,成功生长出直径80mm,高度90mm的完整透明的白宝石单晶,在300～5500nm范围内,其光学透过率均在80;以上.实验中采用高性能保温材料使生长过程所需加热功率由20kW下降到15kW,能耗降低达25;;采用双回路加热系统,提高温场稳定性,缩短晶体生长周期.晶体的主要缺陷为顶部(生长后期)出现有5～10mm淡黄色色带(经在氧化性气氛中退火后已消除)和底部有细丝状条纹.     

LaFeO3单晶生长及其性能研究

以La2O3和Fe2O3粉体为原料,在1400℃,烧结24 h制备出了LaFeO3多晶料棒,采用浮区法生长出LaFeO3单晶。晶体沿(100)晶向生长,晶体的(100)晶面单晶摇摆曲线的半高宽为26″,证实其单晶化程度很高;在298～773 K温度范围内测试了晶体热学性能,晶体比热变化范围为0.58～0.76 J/g.K,热扩散系数变化范围为3.47～0.85 mm2/s,热导率变化范围为13.10～4.21 W/(m.K);研究退火工艺对晶体近红外透过率的影响,在700℃,48h退火可以明显提高透过率达到65%。     

大尺寸金红石(TiO2)单晶体生长条件的实验研究

采用高纯(99.995;)、超细的金红石(TiO2)粉末为起始原料,用燃熔法制备了尺寸为30mm×50mm的金红石(TiO2)单晶体.讨论了生长气氛、生长速度、温度梯度在晶体生长中的作用,对比了晶体在空气中与在氧气中退火的结果,测定了晶体试样的摇摆曲线和透过率,并与商用晶体的透过率进行了比较.实验表明:生长气氛中的氧分压大于液固界面(即生长界面)处熔体的氧离解压是生长完整晶体的必要条件;在此条件下,能否生长为大尺寸晶体则取决于炉膛的轴向温度梯度;晶体在退火过程中可消除热应力,但退火更重要的作用是通过氧化反应消除氧空位,在氧气氛中退火,可明显缩短退火时间;所制备的晶体完整性较好,透过率与商用晶体基本一致.     

直径300 mm氟化钙晶体的生长

通过化学处理提纯晶体原料,采用模拟软件设计合理的温场结构,在系统实验优化晶体生长工艺的基础上,采用改进的坩埚下降生长方法(布里奇曼法)成功地生长出直径300 mm的CaF2晶体.CaF2晶体的透过率在0.15～8.3 μm波长范围内超过80;,最高透过率约为95;.     

Nd:GGG晶体生长与开裂研究

本文采用提拉法(CZ)生长了Nd:GGG晶体,并从理论上讨论了包裹物、提拉速度、晶体转速和降温速率等因素对晶体开裂的影响,最后给出了生长元开裂Nd:GGG晶体的最佳工艺参数:径向温度梯度越小越好,纵向温度梯度在0.5℃/mm,提拉速度2～4mm/h,晶体转速20～40r/min,降温速率不超过20℃/h.通过设计合理而稳定的温场、选择最佳工艺参数及退火处理等方法,较好地解决了Nd:GGG晶体开裂问题.     

Cd:PbWO4晶体的生长及其性质

采用提拉法生长了Cd:PbWO4晶体,最佳生长工艺参数:液面上和液面下轴向温度梯度分别为40～50 ℃/cm和17～25 ℃/cm,生长速度2～3 mm/h,转速为25～30 r/min,以这一条件生长晶体可克服液流转换,避免由此引起的缺陷.Cd:PbWO4的透过率明显高于各类型未掺杂PbWO4晶体,测得Cd:PbWO4的发光效率为21.2 p.e/MeV,而高纯PbWO4为10.5 p.e/MeV,分析纯退火PbWO4为8.2 p.e/MeV,未退火PbWO4为6.7 p.e/MeV.Cd:PbWO4晶体的平均衰减时间约为10 ns.以上结果表明,Cd:PbWO4是一种良好的闪烁晶体.     

CdSiP2单晶退火研究

以高纯(6N) Cd、Si、P单质为原料,采用双温区气相输运法和改进的垂直布里奇曼法合成生长出等径尺寸为φ17 mm×65 mm的CdSiP2单晶锭,经切割抛光得到CdSiP2晶片.将样品分别置于真空、镉气氛、磷气氛和在同成分粉末包裹中进行了退火试验.采用X射线能量色散谱仪(EDS)和傅里叶红外分光光度计(FTIR)对退火前后的晶片组分及红外透过谱进行了测试分析.结果表明:四种氛围退火前后样品的组分变化不大,原子比接近理想的化学计量比;镉气氛下退火对晶片的红外透过率改善较为显著,在1600 ～ 4500 cm-1范围内的红外透过率由46;～52;提高到51; ～57;,接近CdSiP2晶体红外透过率的理论值.     

First-principles coexistence simulations of supercooled liquid silicon

We perform first-principles coexistence simulations of the low-density and the high-density phases of supercooled liquid silicon and find a negative slope for the coexisting line in the temperature-pressure plane. Electron density maps and electron-localization function plots of the two phases of silicon show marked differences. The calculated differences suggest more localized electrons in the low-density liquid compared to the high-density liquid, coming from an increased population of covalent bonds, which further explain the calculated negative slope in the two phase coexistence regime. This is consistent with the presence of a pseudo-gap in low-density liquid silicon, absent in the high-density liquid which shows a metallic behavior.     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

Crystal structures of thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane

Structures of both thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane, ?C₆H₄?CH₂SCH₂?C₆H₁₀?CH₂SCH₂?, have been determined, wherecis andtrans refer to the attachments to the cyclohexane ring. Thecis form crystallizes in the monoclinic space groupP2₁/c witha=8.4299(11)Å,b=21.772(2)Å,c=8.9724(13)Å, β=116.574(11)^o, andZ=4. Thetrans isomer packs into the monoclinic space groupP2₁ witha=8.159(16)Å,b=10.185(5)Å,c=9.558(2)Å, β=112.435(18)^o, andZ=2. The cyclohexane ring of thecis isomer is in the chair conformation, while the cyclohexane of thetrans isomer is found in a twisted boat conformation.     

CTAB与SDBS对碳酸锶粒子生长形态调控及机理研究

以表面活性剂CTAB和SDBS为化学添加剂,采用化学共沉淀法对碳酸锶晶体的生长形态进行调控,成功地制备出了实心的树枝状和花瓣为空心的花状碳酸锶粉体,并用X射线衍射(XRD)、扫描电子显微镜(SEM)和傅里叶变换红外光谱(FT-IR)等分析手段对样品进行了表征;最后重点对化学添加剂可能产生的影响机理进行了初步的探讨.结果表明,CTAB和SDBS在晶体生长的过程中能起到显著的影响作用,两者对粒子分散性能的作用效果相反,而且后者对晶体(013)和(213)晶面表面能降低的贡献明显大于前者.     

Crystal structures of the cis and trans isomers of a tetrathia[3.3.3.3]cyclophane

Both the cis and trans isomers of 3,11,18,26-tetrathiatricyclo[26.2.2.1^5,9.2^13,16.1^20,24] hexatriaconta-5,7,9,20,22,24-hexene have been prepared and structurally characterized. Each of these centrosymmetric tetrathia dimers includes two cyclohexane rings in chair conformations with either 1,4-cis or 1,4-trans bonding and two meta-substituted benzene rings. The cis isomer packs into the monoclinic space group P2₁/a with a = 10.485(3)Å, b = 10.3956(18)Å, c = 14.1343(10)Å, = 105.200(13)°, Z = 2 and refined to an R factor of 0.046. The trans isomer crystallizes in the monoclinic space group P2₁/c with a = 10.7217(12)Å, b = 5.6797(7)Å, c = 25.415(5)Å, = 96.001(12)°, Z = 2 and refined to an R factor of 0.043. In the cis structure each benzene ring faces a cyclohexane ring while in the trans structure the cyclohexane rings face one another.     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

Synthesis and Crystal Structure of 5-[2-(6-bromonaphthalenyloxymethyl)]-3-(4-morpholinomethyl)-1,3,4-oxadiazole-2(3<Emphasis Type="Italic">H</Emphasis>)-thione

Abstract  The title compound, C₁₈H₁₈BrN₃O₃S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal] reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these angles which therefore play a role in stabilizing crystal packing. Graphical Abstract  Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C₁₈H₁₈BrN₃O₃S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

电沉积法制备ZnO纳米棒阵列及其发光特性

本文以掺F的SnO2导电玻璃为基板,以硝酸锌水溶液为电解液,采用三电极恒电位体系电沉积制备ZnO纳米棒阵列,系统考察了硝酸锌浓度和沉积电位等工艺参数对ZnO纳米棒阵列的微观形貌及其发光性能的影响规律.结果表明,硝酸锌浓度和沉积电位对纳米棒阵列的形貌有显著影响,控制适宜的工艺条件可以制备出直径分布均匀、结晶性好且纯度高的六方纤锌矿ZnO纳米棒阵列.荧光光谱分析表明,电沉积制备出的ZnO纳米棒阵列在385 nm附近有一个强荧光发射峰,且发光性能稳定、对纳米棒阵列微观形貌的细微变化不敏感,使其在发光二极管和激光器等领域具有广阔的应用前景.     

Crystal structure of irisolidone from the flowers of Pueraia lobata

Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P2₁/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure.