Morphology and properties of waterborne polyurethane/clay nanocomposites

Aqueous emulsion of polyurethane ionomers, based on poly(tetramethylene glycol) or poly(butylene adipate) as soft segment, isophorone diisocyanate as diisocyanate, 1,4-butandiol as chain extender, dimethyl propionic acid as potential ionic center, triethylene tetramine as crosslinker, and triethyl amine as neutralizer, were reinforced with organoclay to give nanocomposites. The particle size of emulsion was measured and the morphology of these nanocomposites was observed by transmission electron microscope, where the effectively intercalated or exfoliated organoclay was observed. The reinforcing effects of organoclay in mechanical properties of these nanocomposites were examined by dynamic mechanical and tensile tests, and the Shore A hardness was measured. Enhanced thermal and water resistance and marginal reduction in transparency of these nanocomposites were observed compared with pristine polymer.     

Preparation of waterborne polyurethane nanocomposites: Polymerization from functionalized hydroxyapatite

We report the preparation and characterization of waterborne polyurethane (WBPU)/hydroxyapatite (HAp) nanocomposites through in situ polymerization from functionalized HAp. The HAp nanoparticles (HAp NPs) were urethanated with 3-isocyanatemethyl-3,5,5-trimethyl-cyclohexylisocyanate (isophorone diisocyanate) to obtain grafted HAp NPs containing isocyanate groups (HAp-g-NCO) as crosslinkers and then the HAp-g-NCO is further polymerized with WBPU monomers to form the WBPU/HAp nanocomposites. The HAp NPs were homogeneously dispersed in the polyurethane matrix at low loading levels (?2.0 wt%), thus the mechanical strength and the elongation at break of the WBPU/HAp nanocomposites were significantly improved. Thermal stability and water resistance of the WBPU/HAp nanocomposites are also enhanced. These results suggest that the WBPU/HAp nanocomposites prepared by in situ polymerization hold the potential as new materials with improved mechanical properties, thermal stability and water resistance.     

Effect of process variables on mechanical properties of polyurethane/clay nanocomposites

This paper addresses the effects of operating variables on mechanical properties of polyurethane/clay nanocomposites including tensile strength, abrasion resistance, and hardness. The variables were prepolymer type, clay cation, clay content, and prepolymer–clay mixing time. The experiments were carried out based on the design of experiments using Taguchi methods. The nanocomposites were synthesized via in situ polymerization starting from two different types of prepolymers (polyether‐ and polyester‐types of polyol reacted with toluene diisocyanate), and methylene‐bis‐ortho‐chloroanilline (MOCA) as a chain extender/hardener. Montmorillonite with three types of cation (Na⁺, alkyl ammonium ion, and MOCA) were examined. Among the parameters studied, prepolymer type and clay cation have the most significant effects on mechanical properties. Polyester nanocomposites showed larger improvements in mechanical properties compared to polyether materials due to higher shear forces exerted by polymer matrix on clay aggregates during polymer–clay mixing. The original MMT with Na⁺ cation results in weak improvements in mechanical properties compared to organoclays. It is observed that the stress and elongation at break, and abrasion resistance of the nanocomposite samples can be optimized with 1.5% of clay loading. The morphology and chemical structure of the optimum sample were examined by X‐ray diffraction and FT‐IR spectroscopy, respectively. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation and characterization of waterborne polyurethane/attapulgite nanocomposites

In this paper, waterbrone polyurethane (WPU)/attapulgite (AT) nanocomposites have been prepared by direct emulsion blending. The WPU was synthesized from poly(tetramethylene glycol), 4,4-diphenylmethane diisocyanate, dimethylol butanic acid, and neutralized by triethylamine. SEM examination of fractured surfaces showed that AT particles were irregularly dispersed in the WPU matrix. FTIR analysis suggested no major chemical structural changed in the presence of a small amount of AT. DMA results showed that the storage modulus of WPU/AT nanocomposites was increased and the glass transition temperatures of both soft and hard segments shifted to higher temperature compared to the pristine WPU. Thermal resistance of the samples measured by TGA was improved with the addition of AT. The mechanical properties of the nanocomposites, examined by tensile tests, showed higher tensile strength and elongation at break than that of the pristine WPU.     

Bio‐based hyperbranched polyurethane/clay nanocomposites: adhesive,mechanical, and thermal properties

The unison of vegetable oil‐based hyperbranched polymers with nanotechnology can unhook myriad of avant‐garde applications of such materials. Thus Mesua ferrea L. seed oil‐based hyperbranched polyurethane (HBPU)/clay nanocomposites and their performance, with special reference to adhesive strength, are reported for the first time. The nanocomposites of the hyperbranched polyurethane with organically modified nanoclay were obtained by ex situ solution technique and cured by bisphenol‐A‐based epoxy with poly(amido amine) hardener system. The partially exfoliated and well‐distributed structure of nanoclay was confirmed by XRD, SEM, and TEM studies. FTIR spectra indicate the presence of H‐bonding between nanoclay and the polymer matrix. Two times improvement in the adhesive strength and scratch hardness, 10 MPa increments in the tensile strength and 112°C more thermo‐stability have been observed without much affecting the impact resistance, bending, and elongation at break of the nanocomposites compared to the pristine epoxy modified HBPU system. Thus, the resulted nanocomposites are promising materials for different advanced applications including adhesive. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation and properties of PU/MCMMT nanocomposites

The cetyltrimethyl ammonium bromide (CTAB) was used as a swelling agent to be intercalated into the galleries of the montmorillonite (MMT) platelets to get the organic MMT (CMMT). Then 4,4′‐diphenylmethane diisocyanate (MDI) were grafted on CMMT by the reaction between hydroxyls in organic MMT platelets and MDI to synthesize the MDI modified CMMT (MCMMT). Polyurethane (PU)/MCMMT composites were prepared by situ polymerization. The MCMMT platelets dispersed in a PU matrix in nanometer scale. The dispersion and intercalation degree of the MCMMT platelets decreased with increase in the content of MCMMT. Under the same content of fillers, the tensile strength and tear strength of PU/MCMMT nanocomposites were higher than those of PU/organic MMT nanocomposites. The reinforcing effect of the MCMMT platelets to the PU was better than that of the organic MMT platelets. With increase in the content of MCMMT, the tensile strength and tear strength of the PU/MCMMT nanocomposites were increased, while the extent of the increase slowed down. Compared with those of PU, the thermal stability of PU/MCMMT nanocomposites was increased. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and properties of near IR induced self-healable polyurethane/graphene nanocomposites

A series of self-healable polyurethane (SHPU)/modified graphene (MG) nanocomposites were synthesized from poly(tetramethylene glycol) (PTMG) and 4,4′-methylene diphenyl diisocyanate (MDI) with minute amounts (0–1 wt%) of MG which was chemically modified graphene oxide (GO) with phenyl isocyanate and reduced in the presence of phenylhydrazine.     

Optical and mechanical properties of polyurethane/surface-modified nanocrystalline cellulose composites

in order to improve the optical and mechanical performances of waterborne polyurethane （WPU）, nanocrystalline cellulose （NCC）/WPU composites were synthesized in this study. NCC （prepared by acid hydrolysis of cotton fiber） was modified by （3-aminopropyl）triethoxysilane （APTES） to enhance its compatibility with WPU, and the surface-modified NCC was characterized by grafting ratio, crystallinity and contact angle （CA）. NCC/WPU composites were examined by scanning electron microscopy （SEM）, X-ray powder diffraction （XRD） and thermogravimetric analysis （TG）. The anti-yellowing property, specular gloss, pencil hardness, and abrasion resistance of NCC/WPU composites were investigated by the methods of Chinese National Standards GB/T 23999-2009, GB/T 9754-2007, GB/T 6739-2006 and GB/T 1768-2006, respectively. The results showed that the grafting ratio of NCC modified by 6% APTES was 36.01% and the crystallinity of modified NCC was decreased with the enhancement of APTES. CA of the modified NCC was decreased by 28.8% and the nanoparticles were homogeneously dispersed in the WPU matrix. The XRD patterns of the NCC/WPU composites were relatively steady, while the thermal stability of the composites was enhanced by 6.7% with 1.0 wt% modified NCC. Modified NCC affected the specular gloss of NCC/WPU composites more obviously than the anti-yellowing property. The pencil hardness of NCC/WPU composites was increased from 2H to 4H by addition of NCC and the abrasion resistance of the composites was enhanced significantly. In general, NCC/WPU composites showed significant improvements in the optical and mechanical performances.     

Morphology and properties of cyanate ester/liquid polyurethane/silica nanocomposites

The high‐speed homogeneous shearing method was applied to prepare nanocomposites of cyanate ester (CE) with liquid polyurethane elastomer (PUR) and silica. To investigate the influence of various components on the morphology and properties of the ternary composites, the binary composites of CE/PUR and CE/silica were also involved in this article. The morphology of the cured materials of binary and ternary systems was investigated by transmission electron microscopy (TEM), and the results show that silica nanoparticles were uniformly distributed in the ternary and binary matrix. Phase separation of elastomer in composites was not observed by TEM. FTIR test and dynamic mechanical analysis (DMA) proved that chemical linking was existent between PUR and CE. Scanning electron microscopy examinations and mechanical properties tests were carried out. The results show that ternary composites displayed higher fracture toughness and impact strength compared with most of the binary systems. This suggests that the addition of PUR and nanosilica can synergistically improve the toughness of CE. DMA studies confirmed that the incorporation of silica can increase the storage modulus and T_g for CE and CE/PUR system, since there are a good adhesion and a strong hydrogen bonding between silica and polymers. The thermal property of ternary composites increases with the increase of silica nanoparticle loading. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1243–1251, 2008     

Effect of organoclay on thermal and dynamic mechanical properties of novel thermoplastic polyurethane nanocomposites prepared by melt intercalation technique

Polymer nanocomposites based on thermoplastic polyurethane (TPU) containing organophilic montmorillonite (OMMT) were prepared by melt compounding method followed by compression molding. Different percentage of organically modified nanoclays (1, 3, 5, 7, and 9 wt%) was incorporated into the TPU matrix in order to examine the influence of the nanofillers on nanophase morphology and materials' properties. The microstructure morphology of the nanocomposites was examined by transmission electron microscopy (TEM), energy dispersion X‐ray analysis (EDX), wide angle X‐ray diffraction (WAXD), and atomic force microscope (AFM). The observation established that the organoclay is homogeneously dispersed and preferentially embedded in the TPU soft segment phase. Significant enhancement in the thermal stability of the nanocomposites was observed with the addition of the OMMT under thermogravimetric analysis (TGA). Dynamic mechanical properties of the TPU nanocomposites were analyzed using a dynamic mechanical thermal analyzer (DMTA), which confirms that the addition of OMMT has a strong influence on the storage and loss modulus of the TPU matrix. Copyright © 2009 John Wiley & Sons, Ltd.     

Electrospinning of polyurethane/organically modified montmorillonite nanocomposites

Polyurethane/organically modified montmorillonite (PU/O‐MMT) nanocomposites were electrospun and the effect of O‐MMT on the morphology and physical properties of the PU/O‐MMT nanofiber mats were investigated for the first time. The average diameters of the PU/O‐MMT nanofibers were ranged from 150 to 410 nm. The conductivities of the PU/O‐MMT solutions were linearly increased with increasing the content of O‐MMT, which caused a decrease in the average diameters of the PU/O‐MMT nanofibers. The as‐electrospun PU and PU/O‐MMT nanofibers were not microphase separated. The exfoliated MMT layers were well distributed within the PU/O‐MMT nanofibers and oriented along the fiber axis. When the PU/O‐MMT nanofibers were annealed, the exfoliated MMT layers hindered the microphase separation of the PU. The electrospinning of PU/O‐MMT nanocomposites resulted in PU nanofiber mats with improved Young's modulus and tensile strength. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3171–3177, 2005     

Preparation and properties of gluten/calcium carbonate composites

Environment friendly thermosetting composites were prepared by blending wheat gluten （WG） as matrix, calcium carbonate （CaCO3） as filler and glycerol as plasticizer followed by compression molding the mixture at 120 ℃ to crosslink the WG matrix. Morphology observation showed that the CaCO3 particles were finely dispersed in matrix. Incorporation of CaCO3 up to 10 wt% into the composites caused Young＇s modulus and tensile strength to increase markedly. On the other hand, the moisture absorption and elongation at break decreased slightly.     

Hydrogen bonding,mechanical properties,and surface morphology of clay/waterborne polyurethane nanocomposites

A novel clay/waterborne polyurethane (WPU) nanocomposite was synthesized from polyurethane and saponite organoclay. The clay was organically modified with various swelling agents, the effect of which has been investigated. Hydrogen bonding between organic and inorganic materials was characterized with Fourier transform infrared (FTIR) spectroscopy. The results implied that hydrogen bonding increased when organoclay was added. Mechanical and wear property studies revealed that introducing clay into waterborne polyurethane will enhance the Young's modulus (from 56 to 126 MPa), the maximum stress (from 3.9 to 7.6 MPa), and the elongation at break (from 27.7 to 58.7%) of the nanocomposite by a factor of two, whereas the wear loss will be only one third of the neat waterborne polyurethane. Atomic force microscopy (AFM) was used to analyze the surface morphology of the nanocomposite. An AFM microphotograph showed that the surface of the clay/waterborne polyurethane nanocomposite was smoother when clay was added in waterborne polyurethane. The average roughness (R_a) decreased from 1.00 to 0.12. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1–12, 2005     

Electromagnetic interference shielding effectiveness and microwave absorption properties of thermoplastic polyurethane/montmorillonite‐polypyrrole nanocomposites

In this work, thermoplastic polyurethane‐filled montmorillonite‐polypyrrole (TPU/Mt‐PPy) was prepared through melt mixing process for using in electromagnetic shielding applications. The effect of conducting filler content and type, sample thickness, and X‐band frequency range on the electromagnetic interference shielding effectiveness (EMI SE) and EMI attenuation mechanism was investigated. A comparative study of electrical and microwave absorption properties of TPU/Mt‐PPy nanocomposites and TPU/PPy blends was also reported. The total EMI SE average and electrical conductivity of all Mt‐PPy.Cl or Mt‐PPy.DBSA nanocomposites are higher than those found for TPU/PPy.Cl and TPU/PPy.DBSA blends. This behavior was attributed to the higher aspect ratio and better dispersion of the nanostructured Mt‐PPy when compared with neat PPy. Moreover, the presence of Mt‐PPy into TPU matrix increases absorption loss (SE_A) mechanism, contributing to increase EMI SE. The total EMI SE values of nanocomposites containing 30 wt% of Mt‐PPy.DBSA with 2 and 5 mm thickness were approximately 16.6 and approximately 36.5 dB, respectively, corresponding to the total EMI of 98% (75% by absorption) and 99.9% (88% by absorption). These results highlight that the nanocomposites studied are promising materials for electromagnetic shielding applications.     

Nonisocyanate based polyurethane/silica nanocomposites and their coating performance

A series of silica nano-particles with different size were prepared by sol–gel technique, then surface modification by using cyclic carbonate functional organoalkoxysilane (CPS) was performed. Various amounts of carbonated silica particles directly added into carbonated soybean oil (CSBO) and carbonated polypropylene glycol (CPPG) resin mixture to prepare polyurethane–silica nanocomposite coating compositions by nonisocyanate route using an aliphatic diamine as a curing agent. Cupping, gloss, impact, and taber abrasion tests were performed on aluminum panels coated with those nano-composite formulations and tensile tests, thermogravimetric and SEM analyses were conducted on the free films prepared from the same coating formulations. An increase in abrasion resistance of CSBO-CPPG resin combination with the addition of silica was observed. In addition, the maximum weight loss of CSBO-CPPG resin combination was shifted to higher temperatures with incorporation of silica nano-particles The positive effect of modified silica particles on thermal stability of CSBO-CPPG system could be explained in such a way that PPG chains are able to disperse particles in the medium throughout the interactions between ether linkages and silanol groups.     

Synthesis and design of polyurethane and its nanocomposites derived from canola-castor oil: Mechanical,thermal and shape memory properties

The recent global pandemic and its tremendous effect on the price fluctuations of crude oil illustrates the side effects of petroleum dependency more evident than ever. Over the past decades, both academic and industrial communities spared endless efforts in order to replace petroleum-based materials with bio-derived resources. In the current study, a series of shape memory polymer composites (SMPC's) was synthesized from epoxidized vegetable oils, namely canola oil and castor oil fatty acids (COFA's) as a 100% bio-based polyol and isophorone diisocyanate (IPDI) as an isocyanate using a solvent/catalyst-free method in order to eventuate polyurethanes (PU's). Thereafter, graphene oxide (GO) nanoplatelets were synthesized and embedded in the neat PU in order to overcome the thermomechanical drawbacks of the neat matrix. The chemical structure of the synthesized components, as well as the dispersion and distribution levels of the nanoparticles, was characterized. In the following, thermal and mechanical properties as well as shape memory behavior of the specimens were comprehensively investigated. Likewise, the thermal conductivity was determined. This study proves that synthesized PU's based on vegetable oil polyols, including graphene nanoparticles, exhibit proper thermal and mechanical properties, which make them stand as a potential candidate to compete with traditional petroleum-based SMPC's.     

Preparation of thermosetting polyurethane nanocomposites by montmorillonite modified with a novel intercalation agent

A novel thermosetting polyurethane (TSPU)/organic montmorillonite (OMMT) nanocomposite has been synthesized. N‐diamino octadecyl trimethyl ammonium chloride (DODTMAC) was used as an intercalation agent to treat Na⁺‐montmorillonite (MMT) and form a novel kind of OMMT. Fourier transform infrared spectroscopy (FT‐IR), wide angle X‐ray diffraction (WAXD), and thermogravimetric analysis (TGA) data indicated that the MMT was successfully intercalated by this intercalation agent, as evidenced by the fact that the basal spacing of MMT galleries was expanded from 1.5 to 3.2 nm. This OMMT was used to prepare the TSPU nanocomposites. Both the reinforcing and compatibilizing performance of the filler were investigated. Tensile tests showed that the tensile strength of TSPU/OMMT‐4 was the highest, and was about 3.62 times higher than that of the pure TSPU, and also the elongation at break showed an enhancement. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) measurements illustrated that the glass transition temperature of the TSPU/OMMT‐4 nanocomposite was improved from 0.5 to 6.5 °C, which corresponded to the restriction of the soft segments of TSPU. The highest initial and center temperatures of TSPU/OMMT‐4 obtained from TGA were due to the highest retard effect of the TSPU molecular chains. WAXD studies showed that the formation of the nanocomposites in all the cases with the almost disappearance of the peaks corresponding to the basal spacing of MMT. SEM and TEM were used to investigate the morphologies of the TSPU/OMMT‐4 nanocomposite, and demonstrated that the nanocomposite was comprised of a well dispersion of a mixture of intercalated and exfoliated silicate layers throughout the matrix. It was proposed that the nano‐reinforcing effect caused by the well‐dispersed silicate layers might reduce the amount and size of voids and increase the length of the crack‐spreading path during tensile drawing. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 519–531, 2007.     

Study on elastic modulus of crosslinked polyurethane/organoclay nanocomposites

In this paper, two polyurethane/clay nanocomposite systems with crosslinked structure were synthesized via in situ polymerization of a polyether‐ as well as a polyester‐based prepolymer with methylene‐bis‐ortho‐chloroanilline (MOCA). Two types of modified clays with different organic modifiers were used in order to see the effect of compatibility between polymer matrix and clays on elastic modulus of nanocomposites. The morphology and the dispersion of clay layers in polyurethanes have been characterized by X‐ray diffraction (XRD) and microscopic techniques. The changes of elastic modulus of nanocomposites with clay content were examined and compared with those predicted by some conventional composite models. The results showed a reasonable fitting of experimental and theoretical values only at very low clay contents. As the clay content exceeds 1.5 wt% in this system, a reduction in elastic modulus was experimentally observed due to insufficient dispersion degree of silicate layers throughout the crosslinked matrix. This behavior was not predicted with the conventional composite theories. A new model on the basis of Wu model was then developed in order to predict the reduction of elastic modulus at various clay contents in crosslinked PU matrix. This model fitted reasonably the experimental results. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation and properties of compatibilized LDPE/organo-modified montmorillonite nanocomposites

Nanocomposites based on low density polyethylene, containing of 3 or 6 wt.% of organo-modified montmorillonite nanoclay (MMT-ODA) and maleic anhydride grafted low density polyethylene as a compatibilizer were prepared by melt mixing and characterized. Exfoliation of silicate layers was achieved, as confirmed by X-ray diffraction and transmission electron microscopy. The compatibilized nanocomposites exhibit improved thermal stability in air as compared to neat polyethylene and nonexfoliated MMT-ODA composite. The crystallinity and crystallization kinetics of polyethylene matrix is not affected significantly by the presence of MMT-ODA clay. Drawability of the compatibilized nanocomposite with 6 wt.% of MMT-ODA is similar to neat polyethylene, whereas the composition having the same amount of MMT-ODA, without compatibilizer, exhibits poorer drawability. Scanning electron microscopy and density measurements of drawn samples indicate the existence of pores in noncompatibilized composite while no pores and good adhesion to MMT-ODA are found in compatibilized nanocomposites.     

Effects of graphene quantum dot (GQD) on photoluminescence,mechanical, thermal and shape memory properties of thermoplastic polyurethane nanocomposites

A group of shape memory polyurethane‐based nanocomposites containing graphene quantum dot nanoparticles (GQDs) were prepared via in‐situ polymerization method. GQD nanoparticles were synthesized by a facile and rapid microwave‐assisted method and characterized by Fourier‐transform infrared spectroscopy (FTIR), X‐ray diffraction pattern, field emission scanning microscopy, transmission electron microscopy, and fluorescence analysis. Chemical structure and hydrogen bonding index (HBI_[C=O]) of the nanocomposites were analyzed via FTIR spectra. The results show that the incorporation of GQDs in PU matrix reduces HBI_(C=O) of nanocomposites. Crystalline structure and thermal properties of the nanocomposites were investigated by differential scanning calorimetry. As results indicate, nucleation effect of GQDs raises crystallinity content of the samples. Mechanical examinations indicate that incorporation of GQDs improves Young's modulus of the nanocomposites, while their elongation at break values are reduced. In addition, shape memory analyses reveal that the presence of GQDs in PU matrix increases the shape fixity ratios in nanocomposites.