Superhydrophobicity on two-tier rough surfaces fabricated by controlled growth of aligned carbon nanotube arrays coated with fluorocarbon

Considerable effort has been expended on theoretical studies of superhydrophobic surfaces with two-tier (micro and nano) roughness, but experimental studies are few due to the difficulties in fabricating such surfaces in a controllable way. The objective of this work is to experimentally study the wetting and hydrophobicity of water droplets on two-tier rough surfaces for comparison with theoretical analyses. To compare wetting on micropatterned silicon surfaces with wetting on nanoscale roughness surfaces, two model systems are fabricated: carbon nanotube arrays on silicon wafers and carbon nanotube arrays on carbon nanotube films. All surfaces are coated with 20 nm thick fluorocarbon films to obtain low surface energies. The results show that the microstructural characteristics must be optimized to achieve stable superhydrophobicity on microscale rough surfaces. However, the presence of nanoscale roughness allows a much broader range of surface design criteria, decreases the contact angle hysteresis to less than 1 degrees , and establishes stable and robust superhydrophobicity, although nanoscale roughness could not increase the apparent contact angle significantly if the microscale roughness dominates.     

Wetting and dewetting transitions on hierarchical superhydrophobic surfaces

Many natural superhydrophobic structures have hierarchical two-tier roughness which is empirically known to promote robust superhydrophobicity. We report the wetting and dewetting properties of two-tier roughness as a function of the wettability of the working fluid, where the surface tension of water/ethanol drops is tuned by the mixing ratio, and compare the results to one-tier roughness. When the ethanol concentration of deposited drops is gradually increased on one-tier control samples, the impalement of the microtier-only surface occurs at a lower ethanol concentration compared to the nanotier-only surface. The corresponding two-tier surface exhibits a two-stage wetting transition, first for the impalement of the microscale texture and then for the nanoscale one. The impaled drops are subsequently subjected to vibration-induced dewetting. Drops impaling one-tier surfaces could not be dewetted; neither could drops impaling both tiers of the two-tier roughness. However, on the two-tier surface, drops impaling only the microscale roughness exhibited a full dewetting transition upon vibration. Our work suggests that two-tier roughness is essential for preventing catastrophic, irreversible wetting of superhydrophobic surfaces.     

Nanostructures increase water droplet adhesion on hierarchically rough superhydrophobic surfaces

Hierarchical roughness is known to effectively reduce the liquid-solid contact area and water droplet adhesion on superhydrophobic surfaces, which can be seen for example in the combination of submicrometer and micrometer scale structures on the lotus leaf. The submicrometer scale fine structures, which are often referred to as nanostructures in the literature, have an important role in the phenomenon of superhydrophobicity and low water droplet adhesion. Although the fine structures are generally termed as nanostructures, their actual dimensions are often at the submicrometer scale of hundreds of nanometers. Here we demonstrate that small nanometric structures can have very different effect on surface wetting compared to the large submicrometer scale structures. Hierarchically rough superhydrophobic TiO(2) nanoparticle surfaces generated by the liquid flame spray (LFS) on board and paper substrates revealed that the nanoscale surface structures have the opposite effect on the droplet adhesion compared to the larger submicrometer and micrometer scale structures. Variation in the hierarchical structure of the nanoparticle surfaces contributed to varying droplet adhesion between the high- and low-adhesive superhydrophobic states. Nanoscale structures did not contribute to superhydrophobicity, and there was no evidence of the formation of the liquid-solid-air composite interface around the nanostructures. Therefore, larger submicrometer and micrometer scale structures were needed to decrease the liquid-solid contact area and to cause the superhydrophobicity. Our study suggests that a drastic wetting transition occurs on superhydrophobic surfaces at the nanometre scale; i.e., the transition between the Cassie-Baxter and Wenzel wetting states will occur as the liquid-solid-air composite interface collapses around nanoscale structures. Consequently, water adheres tightly to the surface by penetrating into the nanostructure. The droplet adhesion mechanism presented in this paper gives valuable insight into a phenomenon of simultaneous superhydrophobicity and high water droplet adhesion and contributes to a more detailed comprehension of superhydrophobicity overall.     

花生叶表面的高黏附超疏水特性研究及其仿生制备

花生是一种常见的豆科作物.与低黏附超疏水的荷叶不同,花生叶表面同时具有超疏水和高黏附特性.水滴在花生叶表面的接触角为151±2°,显示出超疏水特性.此外,水滴可以牢固地附着在花生叶表面,将花生叶翻转90°甚至180°,水滴均不会从表面滚落,显示了良好的黏附性(黏附力超过80μN).研究发现,花生叶表面呈现微纳米多级结构,丘陵状微米结构表面具有无规则排列的纳米结构.花生叶表面特殊的微纳米多尺度结构是其表面呈现高黏附超疏水特性的关键因素.结合实验数据,对花生叶表面特殊浸润性机理进行了简要阐述.受此启发,利用聚二甲基硅氧烷复形得到了与花生叶表面微结构类似的高黏附疏水表面.本文以期为仿生制备高黏附超疏水表面提供新思路.     

Nano-scale superhydrophobicity: suppression of protein adsorption and promotion of flow-induced detachment

Wall adsorption is a common problem in microfluidic devices, particularly when proteins are used. Here we show how superhydrophobic surfaces can be used to reduce protein adsorption and to promote desorption. Hydrophobic surfaces, both smooth and having high surface roughness of varying length scales (to generate superhydrophobicity), were incubated in protein solution. The samples were then exposed to flow shear in a device designed to simulate a microfluidic environment. Results show that a similar amount of protein adsorbed onto smooth and nanometer-scale rough surfaces, although a greater amount was found to adsorb onto superhydrophobic surfaces with micrometer scale roughness. Exposure to flow shear removed a considerably larger proportion of adsorbed protein from the superhydrophobic surfaces than from the smooth ones, with almost all of the protein being removed from some nanoscale surfaces. This type of surface may therefore be useful in environments, such as microfluidics, where protein sticking is a problem and fluid flow is present. Possible mechanisms that explain the behaviour are discussed, including decreased contact between protein and surface and greater shear stress due to interfacial slip between the superhydrophobic surface and the liquid.     

Mimicking natural superhydrophobic surfaces and grasping the wetting process: a review on recent progress in preparing superhydrophobic surfaces

A typical superhydrophobic (ultrahydrophobic) surface can repel water droplets from wetting itself, and the contact angle of a water droplet resting on a superhydrophobic surface is greater than 150°, which means extremely low wettability is achievable on superhydrophobic surfaces. Many superhydrophobic surfaces (both manmade and natural) normally exhibit micro- or nanosized roughness as well as hierarchical structure, which somehow can influence the surface's water repellence. As the research into superhydrophobic surfaces goes deeper and wider, it is becoming more important to both academic fields and industrial applications. In this work, the most recent progress in preparing manmade superhydrophobic surfaces through a variety of methodologies, particularly within the past several years, and the fundamental theories of wetting phenomena related to superhydrophobic surfaces are reviewed. We also discuss the perspective of natural superhydrophobic surfaces utilized as mimicking models. The discussion focuses on how the superhydrophobic property is promoted on solid surfaces and emphasizes the effect of surface roughness and structure in particular. This review aims to enable researchers to perceive the inner principles of wetting phenomena and employ suitable methods for creation and modification of superhydrophobic surfaces.     

Control of superhydrophilicity/superhydrophobicity using silicon nanowires via electroless etching method and fluorine carbon coatings

Surface roughness is promotive of increasing their hydrophilicity or hydrophobicity to the extreme according to the intrinsic wettability determined by the surface free energy characteristics of a base substrate. Top-down etched silicon nanowires are used to create superhydrophilic surfaces based on the hemiwicking phenomenon. Using fluorine carbon coatings, surfaces are converted from superhydrophilic to superhydrophobic to maintain the Cassie-Baxter state stability by reducing the surface free energy to a quarter compared with intrinsic silicon. We present the robust criteria by controlling the height of the nanoscale structures as a design parameter and design guidelines for superhydrophilic and superhydrophobic conditions. The morphology of the silicon nanowires is used to demonstrate their critical height exceeds several hundred nanometers for superhydrophilicity, and surpasses a micrometer for superhydrophobicity. Especially, SiNWs fabricated with a height of more than a micrometer provide an effective means of maintaining superhydrophilic (<10°) long-term stability.     

Construction of Renewable Superhydrophobic Surfaces via Thermally Induced Phase Separation and Mechanical Peeling

We report a simple preparation method of a renewable superhydrophobic surface by ther-mally induced phase separation (TIPS) and mechanical peeling. Porous polyvinylidene fluo-ride (PVDF) membranes with hierarchical structures were prepared by a TIPS process under different cooling conditions, which were confirmed by scanning electron microscopy and mer-cury intrusion porosimetry. After peeling off the top layer, rough structures with hundreds of nanometers to several microns were obtained. A digital microscopy determines that the surface roughness of peeled PVDF membranes is much higher than that of the original PVDF membrane, which is important to obtain the superhydrophobicity. Water contact angle and sliding angle measurements demonstrate that the peeled membrane surfaces display super-hydrophobicity with a high contact angle (152°) and a low sliding angle (7.2°). Moreover, the superhydrophobicity can be easily recovered for many times by a simple mechanical peel-ing, identical to the original superhydrophobicity. This simple preparation method is low cost, and suitable for large-scale industrialization, which may offer more opportunities for practical applications.     

Control of the water adhesion on hydrophobic micropillars by spray coating technique

We present an alternative approach for controlling the water adhesion on solid superhydrophobic surfaces by varying their coverage with a spray coating technique. In particular, micro-, submicro-, and nanorough surfaces were developed starting from photolithographically tailored SU-8 micropillars that were used as substrates for spraying first poly(tetrafluoroethylene) submicrometer particles and subsequently iron oxide nanoparticles. The sprayed particles serve to induce surface submicrometer and nanoscale roughness, rendering the SU-8 patterns superhydrophobic (apparent contact angle values of more than 150°), and also to tune the water adhesion between extreme states, turning the surfaces from “non-sticky” to “sticky” while preserving their superhydrophobicity. The influence of the chemical properties and of the geometrical characteristics of the functionalized surfaces on the wetting properties is discussed within the frame of the theory. This simple method can find various applications in the fabrication of microfluidic devices, smart surfaces, and biotechnological and antifouling materials.     

Facile Electrochemical Method for the Fabrication of Stable Corrosion-Resistant Superhydrophobic Surfaces on Zr-Based Bulk Metallic Glasses

Both surface microstructure and low surface energy modification play a vital role in the preparation of superhydrophobic surfaces. In this study, a safe and simple electrochemical method was developed to fabricate superhydrophobic surfaces of Zr-based metallic glasses with high corrosion resistance. First, micro–nano composite structures were generated on the surface of Zr-based metallic glasses by electrochemical etching in NaCl solution. Next, stearic acid was used to decrease surface energy. The effects of electrochemical etching time on surface morphology and wettability were also investigated through scanning electron microscopy and contact angle measurements. Furthermore, the influence of micro–nano composite structures and roughness on the wettability of Zr-based metallic glasses was analysed on the basis of the Cassie–Baxter model. The water contact angle of the surface was 154.3° ± 2.2°, and the sliding angle was <5°, indicating good superhydrophobicity. Moreover, the potentiodynamic polarisation test and electrochemical impedance spectroscopy suggested excellent corrosion resistance performance, and the inhibition efficiency of the superhydrophobic surface reached 99.6%. Finally, the prepared superhydrophobic surface revealed excellent temperature-resistant and self-cleaning properties.     

Fabrication of Superhydrophobic Surface with Different Metal Films on Aluminum Alloy

A simple technique was developed for the fabrication of a superhydrophobic surface on the aluminum alloy sheets. Different hierarchical structures(Ag, Co, Ni and Zn) were formed on the aluminum surface by the galvanic replacement reactions. After the chemical modification of them with fluorination, the wettability of the surfaces was changed from superhydrophilicity to superhydrophobicity. Scanning electron microscopy(SEM), energy dispersive spectrometry(EDS) and water contact angle measurement were performed to characterize the morphological characteristic, chemical composition and superhydrophobicity of the surfaces. The as-prepared superhydrophobic surfaces showed a water contact angle as high as ca.160° and sliding angle as low as ca.3°. We hope the method to produce superhydrophobic surface can be used in many fields.     

Preparation of Cu-Coated Stainless Steel Surfaces for Superhydrophobic Investigation

Cu-coated stainless steel surfaces containing micro- and nanoscale binary structures with different surface roughness were successfully fabricated by means of a facile one-step electroless plating technology. The resulting surfaces were modified by the low free energy material HFTHTMS (HFTHTMS = (heptadecafluoro-1,1,2,2-tetrahydrodecyl) trimethoxysilane). The experimental results of wettability exhibit that such unmodified surfaces have a strong adhesive force to water droplets, and their contact angles increase with increasing surface roughness, whereas the modified surfaces by HFTHTMS show the superhydrophobic characteristic with contact angles higher than 150° and sliding angles lower than 5°.     

Superhydrophobic Surfaces Produced by Carbon Nanotube Modified Polystyrene Composite Coating

The present work investigates the enhancement of water repellency on engineering materials surfaces using nanoscale roughness inherent in multi-walled carbon nanotubes (MWCNTs) together with a hydrophobic polystyrene coating via a simple spraying-based technique. The coatings show both a high contact angle and a small sliding angle for water droplets. The different surfaces obtained exhibit contact angles from 125° up to 153° depending on the preparation conditions. The observations of the topology by scanning electron microscopy reveal that the nanostructure created by the MWCNTs and the microstructure induced by the deposition of polystyrene particles forming a two-level structure that conceptually mimics the lotus leaf surface are necessary to create stable superhydrophobic surfaces.     

A facial approach to fabricate superhydrophobic aluminum surface

A facial chemical etching method was developed for fabricating superhydrophobic aluminum surfaces. The resultant surfaces were characterized by scanning electron microscopy, water contact angle (WCA) measurement, and optical methods. The surfaces of the modified aluminum substrates exhibit superhydrophobicity, with a WCA of 154.8° ± 1.6° and a water sliding angle of about 5°. The etched surfaces have binary structure consisting of the irregular microscale plateaus and caves in which there are the nanoscale block‐like convexes and hollows. The superhydrophobicity of aluminum substrates occurs only in some structures in which the plateaus and caves are appropriately ordered. The resulted surfaces have good self‐cleaning properties. The results demonstrate that it is possible to construct superhydrophobic surface on hydrophilic substrates by tailoring the surface structure to providing more spaces to trap air. Copyright © 2009 John Wiley & Sons, Ltd.     

超疏水超亲油玉米秸秆粉油污吸附剂的制备及其在油水分离中的应用

超疏水超亲油材料因其在油水分离等领域有广泛的应用前景而引起人们极大关注。 目前,有很多方法可以用来制备超疏水超亲油材料,但因其过程复杂、成本高、环境适应性差限制了其在实际生产、生活中应用。 本文以玉米秸秆为原料,经TiO₂ 溶胶浸涂并经辛基三甲氧基硅烷修饰后显示出超疏水和超亲油,水滴、油滴在其表面的接触角分别为160°和0°。 研究结果显示,玉米秸秆粉表面的超疏水性源于其表面微纳米复合阶层结构及低表面能化学组成的协同作用。 利用玉米秸秆粉表面的憎水性和亲油性,能将其用于水面油污的吸附和分离,具有分离效率高、稳定性好、可循环利用的优点。 相比于其它材料,以玉米秸秆为原料制备超疏水超亲油的油污吸附剂,原料丰富、成本低、过程简单、易降解、可循环利用,有望在生产、生活中得到应用。     

Preparation of Cu-Coated Stainless Steel Surfaces for Surperhydrophobic Investigation

Cu-coated stainless steel surfaces containing micro- and nanoscale binary structures having different surface roughness were successfully fabricated by means of a facile one-step electroless plating technology, and the resulting surfaces were modified by the low free energy material HFTHTMS (HFTHTMS = (heptadecafluoro-1,1,2,2-tetrahydrodecyl) trimethoxysilane). The experimental results of wettability exhibit that such unmodified surfaces have a strong adhesive force to water droplets, and their contact angles increase with increasing surface roughness, whereas the modified surfaces by HFTHTMS show the superhydrophobic characteristic with contact angles higher than 150° and sliding angles lower than 5°.     

Fabrication of superhydrophobic surfaces from binary colloidal assembly

In this work, superhydrophobic surfaces were derived from binary colloidal assemblies. CaCO(3)-loaded hydrogel spheres and silica or polystyrene ones were consecutively dip-coated on silicon wafers. The former assemblies were recruited as templates for the latter self-assembly. Due to the hydrophilicity difference between silicon wafers and CaCO(3)-loaded hydrogel spheres, the region selective localization of silica or polystyrene spheres leads to irregular binary structures with a hierarchical roughness. The subsequent modification with low surface energy molecules yields a superhydrophobic surface. The heating treatment may largely enhance the mechanical stability of the resulting binary structures, which allows regeneration of the surface superhydrophobicity, providing a good durability in practice.     

Creation of low hysteresis superhydrophobic paper by deposition of hydrophilic diamond-like carbon films

The creation of low hysteresis superhydrophobic paper is reported using a combination of oxygen plasma etching and plasma deposition of an 80 nm non-fluorinated, hydrophilic diamond-like carbon (DLC) coating. The DLC has an equilibrium (flat surface) contact angle (θ _e ) of 68.2° ± 1.5°, which is well below the 90° contact angle that is typically believed to be a prerequisite for superhydrophobicity. Coating of paper substrates with the DLC film yields an advancing contact angle of 124.3° ± 4.1°, but the surface remains highly adhesive, with a receding contact angle <10°. After 60 min of plasma etching and DLC coating, a low hysteresis, superhydrophobic surface is formed with an advancing contact angle of 162.0° ± 6.3° and hysteresis of 8.7° ± 1.9°. To understand the increase in contact angle and decrease in hysteresis, atomic force microscopy and optical profilometry studies were performed. The data demonstrates that while little additional nanoscale roughness is imparted beyond the first 5 min of etching, the roughness at the microscale continually increases. The hierarchical structure provides the appropriate roughness to create low hysteresis superhydrophobic paper from a hydrophilic coating.     

Fabrication of biomimetic superhydrophobic surfaces by a simple flame treatment method

A simple flame treatment method was explored to construct micro/nanostructures on a surface and then fabricate a biomimetic superhydrophobic surface at a relatively low cost. SiO₂‐containing polydimethylsiloxane (PDMS) was used as a substrate. The PDMS replicas with various micropatterned surfaces were fabricated using grass leaf, sand paper, and PET sheet with parallel groove geometry as templates via PDMS replica molding. The PDMS replica surfaces with micron structures and the surface of a flat PDMS sheet as a control sample were further treated by flame. The fabricated surfaces were characterized by scanning electron microscopy and water contact angle measurements. The effect of surface microstructures on the transparency of PDMS was also investigated. The studies indicate that the fine nanoscale structures can be produced on the surfaces of PDMS replicas and a flat PDMS sheet by a flame treatment method, and that the hierarchical surface roughness can be adjusted and controlled by varying the flame treatment time. The flame‐treated surfaces of PDMS replicas and a flat PDMS sheet possess superhydrophobicity and an ultra‐low sliding angle reaching a limiting value of 1°, and the anisotropic wettability of the PDMS replica surface with oriented microgroove structures can be greatly suppressed via flame treatment. The visible light transmittance of the flame‐treated flat PDMS surface decreases with prolonged flame treatment times. Copyright © 2016 John Wiley & Sons, Ltd.     

Condensation and freezing of droplets on superhydrophobic surfaces

Superhydrophobic coatings are reported as promising candidates for anti-icing applications. Various studies have shown that as well as having ultra water repellency the surfaces have reduced ice adhesion and can delay water freezing. However, the structure or texture (roughness) of the superhydrophobic surface is subject to degradation during the thermocycling or wetting process. This degradation can impair the superhydrophobicity and the icephobicity of those coatings. In this review, a brief overview of the process of droplet freezing on superhydrophobic coatings is presented with respect to their potential in anti-icing applications. To support this discussion, new data is presented about the condensation of water onto physically decorated substrates, and the associated freezing process which impacts on the freezing of macroscopic droplets on the surface.