Kinetics of wetting and spreading by aqueous surfactant solutions

Interest in wetting dynamics processes has immensely increased during the past 10-15 years. In many industrial and medical applications, some strategies to control drop spreading on solid surfaces are being developed. One possibility is that a surfactant, a surface-active polymer, a polyelectrolyte or their mixture are added to a liquid (usually water). The main idea of the paper is to give an overview on some dynamic wetting and spreading phenomena in the presence of surfactants in the case of smooth or porous substrates, which can be either moderately or highly hydrophobic surfaces based on the literature data and the authors own investigations. Instability problems associated with spreading over dry or pre-wetted hydrophilic surfaces as well as over thin aqueous layers are briefly discussed. Toward a better understanding of the superspreading phenomenon, unusual wetting properties of trisiloxanes on hydrophobic surfaces are also discussed.     

The Soave,Twu and Boston–Mathias alpha functions in cubic equations of state. Part II. Modeling of thermodynamic properties of pure compounds

Cubic equations of state (EoS) are commonly used for industrial applications, due to their simplicity in predicting pure compound and mixture thermodynamic properties in vapor and liquid phases. The accuracy of their predictions mainly depends on the choice of the attractive term a(T) and numerous models were developed in literature for this purpose. Among them, the Soave and the Twu models have acquired a wide popularity, as well as the Boston–Mathias model commonly used for supercritical applications. However, most of the works concerned with the comparison of literature attractive terms only focuses on the representation of pure component saturation properties. In particular, the analysis of the respective influence of the EoS and the first and second derivatives of the alpha function on the modeling of enthalpies and heat capacities with respect to temperature and pressure, especially in the supercritical range, was never reported in literature. This is precisely the purpose of the present study.     

Mimicking natural superhydrophobic surfaces and grasping the wetting process: a review on recent progress in preparing superhydrophobic surfaces

A typical superhydrophobic (ultrahydrophobic) surface can repel water droplets from wetting itself, and the contact angle of a water droplet resting on a superhydrophobic surface is greater than 150°, which means extremely low wettability is achievable on superhydrophobic surfaces. Many superhydrophobic surfaces (both manmade and natural) normally exhibit micro- or nanosized roughness as well as hierarchical structure, which somehow can influence the surface's water repellence. As the research into superhydrophobic surfaces goes deeper and wider, it is becoming more important to both academic fields and industrial applications. In this work, the most recent progress in preparing manmade superhydrophobic surfaces through a variety of methodologies, particularly within the past several years, and the fundamental theories of wetting phenomena related to superhydrophobic surfaces are reviewed. We also discuss the perspective of natural superhydrophobic surfaces utilized as mimicking models. The discussion focuses on how the superhydrophobic property is promoted on solid surfaces and emphasizes the effect of surface roughness and structure in particular. This review aims to enable researchers to perceive the inner principles of wetting phenomena and employ suitable methods for creation and modification of superhydrophobic surfaces.     

Electrowetting — From statics to dynamics

More than one century ago, Lippmann found that capillary forces can be effectively controlled by external electrostatic forces. As a simple example, by applying a voltage between a conducting liquid droplet and the surface it is sitting on we are able to adjust the wetting angle of the drop. Since Lippmann's findings, electrocapillary phenomena – or electrowetting – have developed into a series of tools for manipulating microdroplets on solid surfaces, or small amounts of liquids in capillaries for microfluidic applications. In this article, we briefly review some recent progress of fundamental understanding of electrowetting and address some still unsolved issues. Specifically, we focus on static and dynamic electrowetting. In static electrowetting, we discuss some basic phenomena found in DC and AC electrowetting, and some theories about the origin of contact angle saturation. In dynamic electrowetting, we introduce some studies about this rather recent area. At last, we address some other capillary phenomena governed by electrostatics and we give an outlook that might stimulate further investigations on electrowetting.     

Analysis of chemical profiles of insect adhesion secretions by gas chromatography–mass spectrometry

This article reports on the chemical analysis of molecular profiles of tarsal secretions of the desert locust Schistocerca gregaria (Forsskål, 1775) by gas chromatography hyphenated with quadrupol mass spectrometry (GC–MS) as well as ¹H-nuclear magnetic resonance (¹H NMR) spectroscopy. Special focus of this study was to elaborate on sampling methods which enable selective microscale extraction of insect secretions in a spatially controlled manner, in particular tarsal adhesive secretions and secretions located on cuticle surfaces at the tibia. Various solvent sampling procedures and contact solid-phase microextraction (SPME) methods were compared in terms of comprehensiveness and extraction efficiencies as measured by signal intensities in GC–MS. Solvent sampling with water as extraction solvent gave access to the elucidation of chemical profiles of polar compound classes such as amino acids and carbohydrates, but is extremely tedious. Contact SPME on the other hand can be regarded as a simplified and more elegant alternative, in particular for the lipophilic compound fraction. Many proteinogenic amino acids and ornithine as well as carbohydrate monomers arabinose, xylose, glucose, and galactose were detected in tarsal secretions after acid hydrolysis of aqueous extracts. Qualitatively similar but quantitatively significantly different molecular profiles were found for the lipid fraction which contained mainly n-alkanes and internally branched monomethyl-, dimethyl-, and trimethyl-alkanes in the C23–C49 range as well as long chain fatty acids and aldehydes. Especially, hydrocarbons with >C40 carbon numbers have previously been rarely reported for insect secretions. The results suggest that the investigated insect secretions are complex emulsions which allow the attachment of tarsi on various otherwise incompatible materials of smooth and rough surfaces. The solid consistence of the established alkanes at ambient temperatures might contribute to a semi-solid consistence of the adhesive, amalgamating partly opposing functions such as slip resistance, tarsal release, desiccation resistance, and mechanical compliance. The methods developed can be extended to other similar applications of studying compositions of insect secretions of other species.     

Wetting/spreading on porous media and on deformable,soluble structured substrates as a model system for studying the effect of morphology on biofilms wetting and for assessing anti-biofilm methods

Biofilm is a layer of syntrophic microorganisms stick to each other and to the surface. The importance of biofilms is enormous in various industrial applications and human everyday life. The effects of biofilm could be either positive or negative. Positive effects are encountered in industrial processes, bioremediation, and wastewater treatment. Negative effects are more common with the marine industry being one of the sectors, which confronts severe corrosion problems caused by biofouling on the surfaces of equipment and infrastructures. In space industry, microbial contamination and biofouling adversely affect both crew health and mission-related equipment, the latter including hardware, water systems, piping, and electrical tools. The capacity of biofilms to grow in space environment was confirmed already in 1991. One of the most important surface properties of biofilms is wettability, which dictates not only how a liquid spreads over the uneven external surface of biofilms but also how it penetrates into their porous and morphologically complex structure. To investigate wetting and spreading onto biofilms, model materials are often used to simulate different morphological and functional features of biofilms in a controlled way, for example, soft, deformable, soluble, structured, porous materials. Here, we review recent advances in wetting and spreading on porous and soft deformable surface together with biofilms wetting properties and its importance in space industry. We conclude with a discussion of the main directions for future research efforts regarding biofilm wetting.     

Measurement and modeling on hydrodynamic forces and deformation of an air bubble approaching a solid sphere in liquids

The interaction between bubbles and solid surfaces is central to a broad range of industrial and biological processes. Various experimental techniques have been developed to measure the interactions of bubbles approaching solids in a liquid. A main challenge is to accurately and reliably control the relative motion over a wide range of hydrodynamic conditions and at the same time to determine the interaction forces, bubble–solid separation and bubble deformation. Existing experimental methods are able to focus only on one of the aspects of this problem, mostly for bubbles and particles with characteristic dimensions either below 100 μm or above 1 cm. As a result, either the interfacial deformations are measured directly with the forces being inferred from a model, or the forces are measured directly with the deformations to be deduced from the theory. The recently developed integrated thin film drainage apparatus (ITFDA) filled the gap of intermediate bubble/particle size ranges that are commonly encountered in mineral and oil recovery applications. Equipped with side-view digital cameras along with a bimorph cantilever as force sensor and speaker diaphragm as the driver for bubble to approach a solid sphere, the ITFDA has the capacity to measure simultaneously and independently the forces and interfacial deformations as a bubble approaches a solid sphere in a liquid. Coupled with the thin liquid film drainage modeling, the ITFDA measurement allows the critical role of surface tension, fluid viscosity and bubble approach speed in determining bubble deformation (profile) and hydrodynamic forces to be elucidated. Here we compare the available methods of studying bubble–solid interactions and demonstrate unique features and advantages of the ITFDA for measuring both forces and bubble deformations in systems of Reynolds numbers as high as 10. The consistency and accuracy of such measurement are tested against the well established Stokes–Reynolds–Young–Laplace model. The potential to use the design principles of the ITFDA for fundamental and developmental research is demonstrated.     

Achieving structural control with thin polystyrene-b-polydimethylsiloxane block copolymer films: The complex relationship of interface chemistry,annealing methodology and process conditions

The structure of thin microphase-separated polystyrene-block-polydimethylsiloxane (PS–PDMS) films has been studied using state-of-the-art top-down and cross-sectional electron microscopy. This is the first time that the profile of PS–PDMS films has been measured in situ and these measurements allowed us to image the shape of the PDMS domains within the film as well as examine the wetting behavior of the block copolymer film on a variety of substrates. It was found that for each polymer, substrate chemistry and annealing method combination examined, there was a small range of film thicknesses whereby the films exhibited the optimal characteristics of high levels of ordering without dewetting or multilayering. Specifically, the optimum thickness for films treated by thermal annealing was greater than that for the equivalent solvent annealed film; a change that was correlated with morphology variations related to solvent swelling of the solvent annealed films. The surface chemistry also induced changes in the optimum film thickness. Selective surfaces were shown to control whether a PDMS wetting layer was formed or not, leading to either thicker or thinner wetting optimum film thicknesses; while undulating morphologies were observed for less selective surfaces. Concomitant changes in the periodicity were then hypothesized to occur as a result of confinement effects and the selectivity of the surface.     

Surface Modification,Topographic Design and Applications of Superhydrophobic Systems

Superhydrophobic surfaces with expanded wetting behaviors, like tunable adhesion, hybrid surface hydrophobicity and smart hydrophobic switching have attracted increasing attention due to their broad applications. Herein, the construction methods, mechanisms and advanced applications of special superhydrophobicity are reviewed, and hydro/superhydrophobic modifications are categorized and discussed based on their surface chemistry, and topographic design. The formation and maintenance of special superhydrophobicity in the metastable state are also examined and explored. In addition, particular attention is paid to the use of special wettability in various applications, such as membrane distillation, droplet-based electricity generators and anti-fogging surfaces. Finally, the challenges for practical applications and future research directions are discussed.     

Wetting characteristics of aqueous rhamnolipids solutions

The wetting properties of surfactants on solid surfaces form the basis of many industrial and biological processes. The preferential adsorption of the surfactants from aqueous solutions onto solid surfaces alter the adhesion tension of the surface and this behavior may cause partial to complete wetting of the surfaces by the aqueous surfactant solutions. However, different types of surfactants show different wetting characteristics. To study the wetting properties of biologically produced rhamnolipids (RL), advancing contact angles of the aqueous solutions of the RL mixture of R1 and R2 in a ratio of R2/R1=1.1 were measured as a function of surfactant concentration. For a comparison of the wetting performance, sodium dodecyl sulfate (SDS) was chosen as the reference surfactant. A hydrophilic glass surface, a hydrophobic polymer, polyethylene terephthalate (PET), and gold surface were used as the solid surfaces to determine the wetting characteristics of rhamnolipids. At low surfactant concentrations (RL concentration <3x10(-5)M, SDS concentration<3x10(-4)M) contact angle (Theta) varied in a certain range depending on the character of the surfactant interactions with the surface. This was followed by a decrease in contact angle. Parallel to this behavior, at low surfactant concentrations the adhesion tension decreased, then remained constant and an increase at higher surfactant concentrations was obtained on hydrophobic surfaces. On hydrophilic surfaces a steady decrease in adhesion tension was observed with both surfactant solutions.     

Dynamic effects of bouncing water droplets on superhydrophobic surfaces

Superhydrophobic surfaces have considerable technological potential for various applications due to their extreme water repellent properties. Superhydrophobic surfaces may be generated by the use of hydrophobic coating, roughness, and air pockets between solid and liquid. Dynamic effects, such as the bouncing of a droplet, can destroy the composite solid-air-liquid interface. The relationship between the impact velocity of a droplet and the geometric parameters affects the transition from the solid-air-liquid interface to the solid-liquid interface. Therefore, it is necessary to study the dynamic effect of droplets under various impact velocities. We studied the dynamic impact behavior of water droplets on micropatterned silicon surfaces with pillars of two different diameters and heights and with varying pitch values. A criterion for the transition from the Cassie and Baxter regime to the Wenzel regime based on the relationship between the impact velocity and the parameter of patterned surfaces is proposed. The trends are explained based on the experimental data and the proposed transition criterion. For comparison, the dynamic impact behavior of water droplets on nanopatterned surfaces was investigated. The wetting behavior under various impact velocities on multiwalled nanotube arrays also was investigated. The physics of wetting phenomena for bouncing water droplet studies here is of fundamental importance in the geometrical design of superhydrophobic surfaces.     

The formation of host–guest complexes between surfactants and cyclodextrins

Cyclodextrins are able to act as host molecules in supramolecular chemistry with applications ranging from pharmaceutics to detergency. Among guest molecules surfactants play an important role with both fundamental and practical applications. The formation of cyclodextrin/surfactant host–guest compounds leads to an increase in the critical micelle concentration and in the solubility of surfactants. The possibility of changing the balance between several intermolecular forces, and thus allowing the study of, e.g., dehydration and steric hindrance effects upon association, makes surfactants ideal guest molecules for fundamental studies. Therefore, these systems allow for obtaining a deep insight into the host–guest association mechanism. In this paper, we review the influence on the thermodynamic properties of CD–surfactant association by highlighting the effect of different surfactant architectures (single tail, double-tailed, gemini and bolaform), with special emphasis on cationic surfactants. This is complemented with an assessment of the most common analytical techniques used to follow the association process. The applied methods for computation of the association stoichiometry and stability constants are also reviewed and discussed; this is an important point since there are significant discrepancies and scattered data for similar systems in the literature.     

Uni-, bi-, and tri-directional wetting caused by nanostructures with anisotropic surface energies

Wetting is a pervasive phenomenon that governs many natural and artificial processes. Asymmetric wetting along a single axis, in particular, has generated considerable interest but has thus far been achieved only by the creation of structural anisotropy. In this paper, we report that such directional wetting can also be achieved by anisotropically coating nanostructure surfaces with materials that modify the nanostructure surface energy, a phenomenon that has not been observed in natural or artificial systems thus far. Moreover, by combining this newfound chemical influence on wetting with topographic features, we are able to restrict wetting in one, two and three directions. A model that explains these findings in terms of anisotropy of the pinning forces at the triple phase contact line is presented. Through the resulting insights, a flexible method for precise control of wetting is created.     

Monte Carlo simulations of vapor–liquid–liquid equilibrium of some ternary petrochemical mixtures

The aim of this study was to determine the capability and accuracy of Monte Carlo simulations to predict ternary vapor–liquid–liquid equilibrium (VLLE) for some industrial systems. Hence, Gibbs ensemble Monte Carlo simulations in the isobaric–isothermal (NpT) and isochoric–isothermal (NVT) ensembles were performed to determine vapor–liquid–liquid equilibrium state points for three ternary petrochemical mixtures: methane/n-heptane/water (1), n-butane/1-butene/water (2) and n-hexane/ethanol/water (3). Since mixture (1) exhibits a high degree of mutual insolubility amongst its components, and hence has a large three-phase composition region, simulations in the NpT ensemble were successful in yielding three distinct and stable phases at equilibrium. The results were in very good agreement with experimental data at 120 kPa, but minor deviations were observed at 2000 kPa. Obtaining three phases for mixture (2) with the NpT ensemble is very difficult since it has an extremely narrow three-phase region at equilibrium, and hence the NVT ensemble was used to simulate this mixture. The simulated results were, once again, in excellent agreement with experimental data. We succeeded in obtaining three-phase equilibrium in the NpT ensemble only after knowing, a priori, the correct three-phase pressure (corresponding to the force fields that were implemented) from NVT simulations. The success of the NVT simulation, compared to NpT, is due to the fact that the total volume can spontaneously partition itself favorably amongst the three boxes and only one intensive variable (T) is fixed, whereas the pressure and the temperature are fixed in an NpT simulation. NpT simulations yielded three distinct phases for mixture (3), but quantitative agreement with experimental data was obtained at very low ethanol concentrations only.     

Factors influencing the contact angle value. The contact angle,as a characteristic of the properties of solid surfaces

A survey of publications concerning the properties of solids in relation to wetting phenomena is presented. Factors influencing the contact angle value as well as problems of objective approach to research into wetting phenomena are discussed. Peculiarities of the direct and reverse processes during the formation of the solid—liquid—vapor three-phase contact and the inevitability of contact angle hysteresis for polar solids and liquids are analyzed. It is suggested that contact angle hysteresis is due to high energy of the interaction between the liquid and the solid and hence a long relaxation time of the three-phase contact system. Specific features of the response of a solid surface to all surface processes (“chemomechanics”) is discussed. Cleaning of solid surfaces as well as surface preparation for repeated measurements is considered. It is shown that good reproducibility of results is possible if conditions for sample preparation are met. The results of determination of the activation energy for wetting of glass surface with water are presented. The influence of the structure of solids (their hardness) on the contact angle values is demonstrated. Inevitability of the presence of different-type active sites characterized by different dissociation constants (pK_a) on the surface of solids is discussed. The pK_a values and content of these surface sites obtained from potentiometric titration and wetting data are estimated. The estimates thus obtained are in reasonable agreement with each other and can thus be used in practical applications. However, potentiometric titration is currently inappropriate for evaluating the content of individual surface sites as well as the surface charge.     

Wetting–dewetting films: The role of structural forces

The liquid wetting and dewetting of solids are ubiquitous phenomena that occur in everyday life. Understanding the nature of these phenomena is beneficial for research and technological applications. However, despite their importance, the phenomena are still not well understood because of the nature of the substrate's surface energy non-ideality and dynamics. This paper illustrates the mechanisms and applications of liquid wetting and dewetting on hydrophilic and hydrophobic substrates. We discuss the classical understanding and application of wetting and film stability criteria based on the Frumkin–Derjaguin disjoining pressure model. The roles of the film critical thickness and capillary pressure on the film instability based on the disjoining pressure isotherm are elucidated, as are the criteria for stable and unstable wet films. We consider the film area in the model for the film stability and the applicable experiments. This paper also addresses the two classic film instability mechanisms for suspended liquid films based on the conditions of the free energy criteria originally proposed by de Vries (nucleation hole formation) and Vrij–Scheludko (capillary waves vs. van der Waals forces) that were later adapted to explain dewetting. We include a discussion of the mechanisms of nanofilm wetting and dewetting on a solid substrate based on nanoparticles' tendency to form a 2D layer and 2D inlayer in the film under the wetting film's surface confinement. We also present our view on the future of wetting–dewetting modeling and its applications in developing emerging technologies. We believe the review and analysis presented here will benefit the current and future understanding of the wetting–dewetting phenomena, as well as aid in the development of novel products and technologies.     

A new sensor for ammonia based on cyanidin-sensitized titanium dioxide film operating at room temperature

Design and fabrication of an ammonia sensor operating at room temperature based on pigment-sensitized TiO₂ films was described. TiO₂ was prepared by sol–gel method and deposited on glass slides containing gold electrodes. Then, the film immersed in a 2.5 × 10⁻⁴ M ethanol solution of cyanidin to absorb the pigment. The hybrid organic–inorganic formed film here can detect ammonia reversibly at room temperature. The relative change resistance of the films at a potential difference of 1.5 V is determined when the films are exposed to atmospheres containing ammonia vapors with concentrations over the range 10–50 ppm. The relative change resistance, S, of the films increased almost linearly with increasing concentrations of ammonia (r = 0.92). The response time to increasing concentrations of the ammonia is about 180–220 s, and the corresponding values for decreasing concentrations 240–270 s. At low humidity, ammonia could be ionized by the cyanidin on the TiO₂ film and thereby decrease in the proton concentration at the surface. Consequently, more positively charged holes at the surface of the TiO₂ have to be extracted to neutralize the adsorbed cyanidin and water film. The resistance response to ammonia of the sensors was nearly independent on temperature from 10 to 50 °C. These results are not actually as good as those reported in the literature, but this preliminary work proposes simpler and cheaper processes to realize NH₃ sensor for room temperature applications.     

Automated on-line liquid–liquid extraction system for temporal mass spectrometric analysis of dynamic samples

Most real samples cannot directly be infused to mass spectrometers because they could contaminate delicate parts of ion source and guides, or cause ion suppression. Conventional sample preparation procedures limit temporal resolution of analysis. We have developed an automated liquid–liquid extraction system that enables unsupervised repetitive treatment of dynamic samples and instantaneous analysis by mass spectrometry (MS). It incorporates inexpensive open-source microcontroller boards (Arduino and Netduino) to guide the extraction and analysis process. Duration of every extraction cycle is 17 min. The system enables monitoring of dynamic processes over many hours. The extracts are automatically transferred to the ion source incorporating a Venturi pump. Operation of the device has been characterized (repeatability, RSD = 15%, n = 20; concentration range for ibuprofen, 0.053–2.000 mM; LOD for ibuprofen, ∼0.005 mM; including extraction and detection). To exemplify its usefulness in real-world applications, we implemented this device in chemical profiling of pharmaceutical formulation dissolution process. Temporal dissolution profiles of commercial ibuprofen and acetaminophen tablets were recorded during 10 h. The extraction-MS datasets were fitted with exponential functions to characterize the rates of release of the main and auxiliary ingredients (e.g. ibuprofen, k = 0.43 ± 0.01 h⁻¹). The electronic control unit of this system interacts with the operator via touch screen, internet, voice, and short text messages sent to the mobile phone, which is helpful when launching long-term (e.g. overnight) measurements. Due to these interactive features, the platform brings the concept of the Internet-of-Things (IoT) to the chemistry laboratory environment.