碳纳米管改性聚苯硫醚熔纺纤维的结构与性能研究

将多壁碳纳米管(MWCNTs)和聚苯硫醚(PPS)经过熔融挤出后制备成复合材料切片,并采用熔融纺丝法制得碳纳米管改性聚苯硫醚复合纤维.采用扫描电镜(SEM)、拉曼光谱、示差扫描量热分析(DSC)、动态机械分析(DMA)以及力学性能测试等表征手段研究了复合纤维中碳管的分散状态,与基体的界面作用,复合纤维的结晶性能以及力学性能,从而探讨了聚苯硫醚/碳纳米管复合纤维体系的微观结构与宏观性能之间的关系.研究表明,聚苯硫醚分子结构与碳纳米管之间具有的π-π共轭作用使碳管较为均匀的分散在基体中,界面结合较为紧密.同时熔融纺丝过程中的拉伸作用使碳管进一步解缠并使碳管沿纤维拉伸方向取向.另一方面,拉曼光谱显示拉伸作用有效地增强了界面作用,有利于外界应力的传递.碳管的良好分散以及强的界面作用使复合纤维力学性能得到大幅度的提高,当碳管含量达到5 wt%时,复合纤维的模量有了明显的提高,拉伸强度较纯PPS纤维提高了近220%.     

单宁酸改性制备光敏碳纳米管及UV光固化AESO复合膜的制备

本文以单宁酸（TA）和甲基丙烯酸缩水甘油酯（GMA）为原料，通过开环反应制备出含有双键的光敏单宁酸（pTA），并通过π-π非共价键作用使其吸附到碳纳米管上，得到pTA修饰后的具有良好分散性的光敏碳纳米管（pTA/MWCNTs）。再将该pTA/MWCNTs作为填料添加到环氧大豆油丙烯酸酯（AESO）中，通过UV光固化得到AESO-pTA/MWCNTs复合膜。利用pTA对MWCNTs进行改性，提高了MWCNTs的分散性，同时引入双键，使得pTA/MWCNTs能够参与到光固化过程中，提高了碳纳米管与AESO基质间的界面粘结力，对AESO起到了比较好的增强作用。本文还研究了pTA/MWCNTs的加入对AESO复合涂料光固化动力学及涂膜性能的影响，结果表明该pTA/MWCNTs的掺入提高了光固化AESO复合膜的力学性能，当掺入量为0.8%时，对膜的增强效果最好，与纯AESO比较，其拉伸模量提高了390%，拉伸强度提高了110%。     

聚苯氧基磷酸联苯二酚酯/聚磷酸铵膨胀阻燃剂对环氧树脂阻燃性能影响研究

以聚苯氧基磷酸联苯二酚酯(PBPP)与聚磷酸铵(APP)组成复合阻燃剂,对环氧树脂(EP)进行阻燃改性.通过氧指数(LOI)、垂直燃烧(UL-94)、热失重(TGA)、锥形量热(CONE)和扫描电镜(SEM)等方法研究改性环氧树脂的阻燃性能和阻燃机理.结果表明,PBPP/APP体系对EP具有较好的阻燃性能,阻燃剂添加量为10%时能使环氧树脂的氧指数提高到29.6%,垂直燃烧等级达到UL94 V-0级,残炭量大大增加;平均热释放速率下降45.7%,热释放速率峰值下降51.0%,有效燃烧热平均值下降21.1%;TGA、CONE、SEM等综合分析显示了PBPP/APP改性后的环氧树脂比纯环氧树脂具有更高的热稳定性,燃烧后能够形成连续、致密、封闭、坚硬的焦化炭层,在聚合物表面产生有效覆盖、隔绝了氧气,改善了环氧树脂的燃烧性能.     

甲基磺酸对PBO纤维的表面改性

采用甲基磺酸(MSA)溶液对PBO纤维表面进行化学改性,用单丝拔出试验测定了改性前后PBO纤维与环氧树脂基体的界面剪切强度,并通过扫描电镜(SEM)、X-射线光电子能谱(XPS)、接触角分别对处理前后纤维的表面形貌、表面组成以及表面自由能进行了表征.研究结果表明:在甲基磺酸质量分数为60%的溶液中,60℃下处理6 h的PBO纤维与环氧树脂基体的界面剪切强度比未处理的提高了81%,并且纤维表面O元素的质量分数增加了13.3%,表面自由能增加了17.3%.当溶液中甲基磺酸的质量分数、处理时间和处理温度进一步提高时,PBO纤维的皮层将遭受破坏,导致界面剪切强度下降.     

碳纳米管的羟甲基化及其马来酸酐接枝研究

利用甲醛的亲电性能, 对化学气相沉积法(CVD)制备的多壁碳纳米管(MWCNTs)进行羟甲基化, 并在此基础上酯化接枝马来酸酐, 运用透射电子显微镜(TEM)、红外光谱和Zeta电位仪表征了改性后的MWCNTs的表面结构. TEM结果显示, 酯化后的MWCNTs明显增粗, 说明表面已附有物质. 红外结果表明, 羟甲基后的MWCNTs的表面有了羟基和亚甲基, 而马来酸酐酯化接枝后的MWCNTs有亚甲基和酯基官能团. 光学图像分析表明, 经甲醛处理后的MWCNTs在水溶液中的分散性明显提高, 而马来酸酐酯化接枝后的MWCNTs在二甲苯中的分散性明显增强. Zeta电位的测试结果表明, 甲醛处理过的MWCNTs颗粒在水中, 负电荷增多, 增强了其在悬浮液在溶液中的稳定性.     

氧化石墨烯与Si-P低聚物在环氧树脂中的协同阻燃作用

采用Hummers方法制备了氧化石墨烯(GO),并通过扫描电镜(SEM)和原子力显微镜(AFM)对GO微观形貌进行了表征.详细研究了GO与硅磷低聚物(DMS-DOPO)在环氧树脂(EP)力学性能和阻燃性能中的协同作用.万能材料试验测试结果表明,GO和DMS-DOPO分别对拉伸强度和断裂伸长率提高效果明显,二者协同后,可使EP拉伸强度和断裂伸长率分别提高17.1%和42.2%.采用热重分析(TG)、极限氧指数(LOI)、垂直燃烧(UL-94)、锥型量热(CONE)和SEM对EP及其阻燃材料的热性能、燃烧性能以及炭层微观形貌进行了表征.EP/DMS-DOPO/GO在600℃残留量为EP的5.2倍,比EP/DMS-DOPO和EP/GO分别提高4.4%和208.6%.EP/DMS-DOPO/GO的LOI值大于30,并能通过UL-94 V-0级别,燃烧过程中可形成内部结构疏松多孔、外表面致密的膨胀炭层.DMS-DOPO和GO协同后使EP热释放速率峰值由1154 k W·m-2降低到710 k W·m-2,总烟释放量降低30%.     

生物基氢化香豆素增韧环氧树脂的制备及性能

通过生物基原料氢化香豆素(DHC), 在铬(Ⅲ)络合物和氯化铵复合物协同催化作用下, 与环氧醚类物质交替共聚, 获得一类三维网状聚合物, 进而与环氧树脂(EP)单体在固化过程中构建双网络结构, 实现有效的应力传递和外部能量吸收, 达到对环氧树脂增韧增强的效果. 凝胶渗透色谱结果表明, DHC基网络(DHC-net)分子量随反应时间延长而增加. ¹H NMR证实了合成的DHC-net分子结构. 同时, 考察了环氧树脂的热力学及力学性能, 发现DHC-net与环氧树脂基体具有良好的相容性; 改性后的环氧树脂断裂伸长率比纯环氧树脂有大幅提高; 拉伸与冲击测试显示, DHC-net含量小于30%时, 改性后环氧树脂的拉伸强度和抗冲击强度均比纯环氧树脂有大幅提高.     

碳纳米管改性环氧树脂的导热和阻燃性能

以双酚A二缩水甘油醚(DGEBA)环氧树脂(Epoxy Resin,EP)为基体、甲基六氢苯酐(MHHPA)为固化剂、以多壁碳纳米管(MWCNTs)为添加剂制备了环氧树脂/碳纳米管纳米复合材料。通过对微观结构、玻璃化转变温度(Tg)、热失重、热导率和锥形量热测试结果分析,研究了质量分数少于1.5%的MWCNTs对环氧树脂的导热和阻燃性能影响,结果表明,MWCNTs质量分数为1.5%时,复合材料发生团聚;纳米复合材料随着MWCNTs质量分数的增加Tg值先增加后降低;失重5%时,对应的温度先增加后降低,残炭量增加;样品的热导率呈现先升高后降低的趋势,当MWCNTs质量分数为1%时,复合材料的热导率最大;MWCNTs加入后环氧树脂的总释热量减少,释烟量增加,阻燃性得到一定程度的提高。     

纳米纤维素晶须的表面改性及其在环氧树脂中的应用

以棉纤维素为原料,采用硫酸水解法制备了纳米纤维素晶须.以N,N-二甲基甲酰胺(DMF)为分散介质,二甲基氨基吡啶(DMAP)为催化剂,十二烯基琥珀酸酐为酯化剂对纳米纤维素晶须进行化学改性,得到了一系列取代程度不同的改性产物(记为DCNW).采用红外光谱(FTIR)、X射线衍射(XRD)、透射电子显微镜(TEM)和X射线光电子能谱(XPS)等手段对DCNW的结构和性能进行了分析和表征.选择表面取代度为0.3的改性产物作为复合材料的增强相.该改性产物能在丙酮中均匀分散和稳定悬浮,并且保持了改性前纳米纤维素晶须的棒状形态和高结晶度.将其分散于环氧单体中,通过浇铸法制备了纳米复合材料,考察了改性纳米纤维素晶须添加量对纳米复合材料拉伸性能、动态力学性能及耐湿热性的影响规律.结果表明,与空白环氧树脂相比,添加了改性纳米纤维素晶须的纳米复合材料的拉伸强度、杨氏模量和断裂伸长率都得到了提高.玻璃化转变温度、耐湿热性也得到了显著改善.其中,当改性纳米纤维素晶须的添加量为3.5%时,拉伸强度从纯环氧的39.85 MPa提高到72.33 MPa,增加了82%;杨氏模量增大了21%;断裂伸长率从纯环氧树脂的2.45%提高到7.29%,增加了198%;Tg值从纯环氧的103.4℃,提高到134.1℃;吸水率从1.9%下降到1.4%.     

复合改性竹纤维/聚丙烯复合材料的制备与性能研究北大核心CSCD

为改善竹纤维(BF)与聚丙烯(PP)的界面结合,采用碱(NaOH)和异氰酸酯偶联剂(TDI)复合改性竹纤维,制备BF/PP复合材料。分析了竹纤维改性前后主要化学成分、热行为及化学结构变化,考察了竹纤维改性对复合材料维卡软化点(VSP)和动态热力学性能影响,用扫描电镜对复合材料断面进行了观察,最后探讨了改性竹纤维添加量对复合材料力学性能的影响。结果表明:BF经复合改性后,表面形成了氨酯键结构,竹纤维素晶体尺寸和结晶度增大,竹纤维的最快热降解温度和复合材料的VSP分别提高了20℃和4.5℃。SEM、DMA分析显示,竹纤维复合改性改善了两相界面结合,利于力学性能提高。拉伸实验表明,在复合改性竹纤维添加比例为40%时,复合材料综合性能最佳,其冲击强度、拉伸强度和弯曲强度分别增加了21.6%、23.3%和27.8%,拉伸模量和弯曲模量分别增加了24.2%和30.4%。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。