A novel spectrophotometric determination of copper(Ⅱ) with bromosulphonazo Ⅲ

A novel ehromogenic reaction involving copper(Ⅱ) and bromosulphonazo Ⅲ (Br-SAZⅢ) in hexamethylenetetramine-hydrochloric buffer solution was investigated. The results showed that a blue complex of copper(Ⅱ) and bromosulphonazo Ⅲwas formed with a molar ratio of 1:1. The apparent molar absorptivity was 3.3 × 105Lmol-1cm-1 and themaximum absorption peak was at 616.8 nm. The proposed procedure was used for quantitative estimation of Cu(Ⅱ) inthe concentration range of 0-1.024 μg/mL with the detection limit (3σ) of 7.03 × 10-4 μg/mL (n = 20). The relativestandard deviations (RSDs) were 0.56-4,68%. Under the optimized conditions, total copper in the vegetables and tea wassuccessfully determined.     

STUDY ON THE DETERMINATION OF TRACE Fe（III） BY THIN LAYER RESIN PHASE SPECTROPHOTOMETRY

A method to determine Fe（Ⅲ） by thin layer resin phase spectrophotometry has been developed in this paper. The colored complex formed by Fe（Ⅲ） and 1,2-benzendiol is concentrated on the 717^# resin, then Fe（Ⅲ） can be determined directly by making thin layer. The method is sensitive with a apparent molar absorption of 4.8×10^4L/mol.cm, which is 16 times higher than that of liquid phase spectrophotornetry, most coexisting ions do not influence the determination. The detection limit for Fe（Ⅲ） is 1.47μg/L with the precision of 3.3% [n=6, 7μg/50mL Fe（Ⅲ）]. The calibration curve is linear in the range of 0-25μg/50mL. The preposed method was applied to the determination of Fe（Ⅲ） in water sample with satisfactory results.     

Iodide-selective polymeric membrane electrode based on copper(Ⅱ) bis(N-2-bromophenylsalicyldenaminato) complex

A PVC membrane electrode based on copper（Ⅱ） bis（N-2-bromophenylsalicyldenaminato） as ionophor was prepared.The ion selective electrode was tested by inorganic anions and showed a good selectivity for iodide ion.This sensor exhibited Nernstian behavior with a slope of—57.8 mV per decade at 25℃.The proposed electrode showed a linear range from 1.0×10⁵ to 1.0×10^-1 mol/L with a detection limit of 5.0×10^-6 mol/L.The electrode response was independent of pH in the range of 3.0- 10.0.The proposed sensor was applied to determine the iodide in water and antiseptic samples.     

FLAME ATOMIC ABSORPTION DETERMINATION OF COPPER IN CEREALS FOOD SAMPLES WITH THE PRECONCENTRATION OF POTASSIUM TETRATITANATE WHISKER

A simple and reliable method has been developed for separation and preconcentration of trace amounts of copper ions in cereals food for subsequent measurement by flame atomic absorption spectrometry （FAAS）. The Cu^2＋ ions are adsorbed selectively and quantitatively during the passage. The retained copper ions were desorbed from the potassium tetratitanate whisker with 10.0mL of 2mol/L sulphuric acid solutions as eluent and were determined by FAAS. The linear range was 0.05μg/mL-0.20μg/mL in the original solution with a correlation coefficient of 0.9998. The detection limit of the proposed method is 2. lng/mL in the original solution （3σ, n=9）. Determination of copper in standard ions showed that the proposed method has good accuracy （recovery was more than 95%）. The method was successfully applied for recovery and determination of copper in cereals food samples     

N~1,N~2-Bis[1-(2-hydroxyphenyl)methylidene]ethanedihydrazide as a neutral ionophore for preparation of a new Ho~(3+) PVC-membrane sensor

N¹,N²-Bis[1-（2-hydroxyphenyl）methylidene]ethanedihydrazide（MEH） was used as new compound which plays the role of an excellent ion carrier in the fabrication of a Ho（Ⅲ） membrane electrode.The electrode shows a good selectivity for Ho（Ⅲ） ion with respect to most common cations including alkali,alkaline earth,transition and heavy metal ions.This electrode has a wide linear dynamic range from 1.0×10^-6 to 1.0×10^-2 mol/L with a Nernstian slope of 19.8±0.3 mV per decade and a low detection limit of 5.8×10^-7 mol/L in the pH range of 2.5-9.8,while the response time was rapid（<10 s）.The suggested sensor was applied to the determination of Ho（Ⅲ） ions in tap water and river water samples.     

Highly Selective Salicylate Membrane Electrode Based on N,N＇- （Aminoethyl）ethylenediamide Bis（2-salicylideneimine） Binuclear Copper（Ⅱ） Complex as Neutral Carrier

A new ion selective electrode for salicylate based on N,N＇-（aminoethyl）ethylenediamide bis（2-salicylideneimine） binuclear copper（Ⅱ） complex [Cu（Ⅱ）2-AEBS] as an ionophore was developed. The electrode has a linear range from 1.0 × 10^-1 to 5.0 ×10^-7 mol·L^- 1 with a near-Nemstian slope of （ - 55 ±1 ） mV/decade and a detection limit of 2.0 × 10-7 mol·L^-1 in phosphorate buffer solution of pH 5.0 at 25 ℃. It shows good selectivity for Sal^- and displays anti-Hofmeister selectivity sequence： Sal^-〉SCN^-〉 ClO4^- 〉I^-〉 NO2^- 〉Br^-〉 NO3^- 〉Cl^-〉 SO3^2- 〉 SO4^2- The proposed sensor based on binuclear copper（Ⅱ）complex has a fast response time of 5-10 s and can be used for at least 2 months without any major deviation. The response mechanism is discussed in view of the alternating current （AC） impedance technique and the UV-vis spectroscopy technique. The effect of the electrode membrane compositions and the experimental conditions were studied. The electrode has been successfully used for the determination of salicylate ion in drug pharmaceutical preparations.     

Simple,Selective, and Sensitive Spectrophotometric Method for Determination of Trace Amounts of Nickel（Ⅱ）, Copper （Ⅱ）, Cobalt （Ⅱ）, and Iron （Ⅲ） with a Novel Reagent 2-Pyridine Carboxaldehyde Isonicotinyl Hydrazone

A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone（2-PYAINH） was synthesized and studied for the spectrophotometric determination of nickel, copper, cobalt, and iron in detail. At a pH value of 7.0, 9,0, 9.0, and 8.0, respectively, which greatly increased the selectivity; nickel, copper, cobalt, and iron reacted with 2-PYAINH to form a 1：2 yellow-orange, 1：2 yellow-green, 1：2 yellow and 1：1 yellow complexes, with absorption peaks at 363, 352, 346, and 359 nm, respectively. Under the optimal conditions, Beer＇s law was obeyed over the ranges of 0.01-1.4, 0.01-1.5, 0.01-2.7, and 0.01-5.4 mg/L respectively. The apparent molar absorptivity and Sandell＇s sensitivities were 8.4×10^4, 5.2×10^4, 7.1×10^4, and 3.9×10^4 L·mol^-l·cm^-1, respectively, and 0.00069, 0.0012, 0.00078, and 0.0014 μg·cm2, respectively. The detection limits were found to be 0.001, 0.002, 0.003, and 0.01 mg/L, respectively. The detailed study of various interfering ions to make the method more sensitive was carried out and selective and several real samples were analyzed with satisfactory results.     

四氮大环-金属配合物与DNA作用的电化学及谱学研究

Mononuclear copper（Ⅱ）, nickel（Ⅱ） and cobalt（Ⅲ） tetracoordinate macrocyclic complexes were synthesized and spectroscopically characterized. The crystal structure of the three compounds were determined by X-ray crystallography. The electrochemical experimental results indicate that the three complexes could interact with DNA mainly by electrostatic interaction. The interaction of tetracoordinate macrocyclic cobalt（Ⅲ） complex with DNA was studied by cyclic voltammetry and UV-vis spectroscopy. The experimental results reveal that tetracoordinate macrocyc- lic cobalt（Ⅲ） complex could interact with DNA by electrostatic interaction to form a 1 ： 1 DNA association complex with a binding constant of 7.50 ×10^3 L·mol^-1.     

A novel method for the determination of trace copper in cereals by dispersive liquid-liquid microextraction based on solidification of floating organic drop coupled with flame atomic absorption spectrometry

A novel,simple,rapid,efficient and environment-friendly method for the determination of trace copper in cereal samples was developed by using dispersive liquid-liquid microextraction based on solidification of floating organic drop(DLLME-SFO) followed by flame atomic absorption spectrometry.In the DLLME-SFO,copper was complexed with 8-hydroxy quinoline and extracted into a small volume of 1-dodecanol,which is of low density,low toxicity and proper melting point near room temperature. The experimental parameters affecting the extraction efficiency were investigated and optimized.Under the optimum conditions, the calibration graph exhibited linearity over the range of 0.5—500 ng/mL with the correlation coefficient(r) of 0.9996.The enrichment factor was 122 and the limit of detection was 0.1 ng/mL.The method was applied to the determination of copper in the complex matrix samples such as rice and millet with the recoveries for the spiked samples at 5.0 and 10.0 u,g/g falling in the range of 92.0-98.0%and the relative standard deviation of 3.9-5.7%.     

A novel method for the spectrophotometric determination of cefradine by using sodium nitroprusside as chromogenic reagent

A novel method is developed for the determination of cefradine by using sodium nitroprusside as chromogenic reagent. The experiment indicates that a russety product is formed by the reaction of cefradine with sodium nitroprusside in basic solution, and the maximum absorption wavelength （λmax） of russety product is 505 rim. And the sensitization of tetradecyl benzyl dimethyl ammonium chloride for the reaction of cefradine with sodium nitroprusside is remarkable, The apparent molar absorption coefficient （5505） is 2.81 × 103 L/mol cm. The linear equation isA = 0.0657 ＋ 0.00804C （μg/mL） in the range of 1.50-55.0μg/mL of cefradine with a correlation coefficient r = 0.9992, and the detection limit is 1.38 p,g/mL. This method has been applied to determine cefradine in capsule and tablet samples.     

Synthesis of Polyacrylaminothiourea Chelating Fiber and Properties of Concentration and Separation of Trace Noble Metal Ions from Samples

A novel polyacrylaminothiourea chelating fiber was synthesized simply and rapidly from nitrilon (an acrylonitrile-based synthetic fiber), which was applied to preconcentrate and separate of trace amount of Au(Ⅲ）,Pt(Ⅳ）,Pd(Ⅳ） and Ir (Ⅳ） ions from solution of samples.The analyzed ions can be quantitatively concentrated by the fiber up to a flow rate of 20.0mL/min at pH2, and can also be desorbed with 15 mL of 4mol/L HCl 3% thiourea from the fiber column with recoveries of 96.5%-100%.The chelating fiber can be reused for ten times,the recoveries of these ions are still over 92%,and hundred to thousand times of excess of Fe(Ⅲ）,Al（Ⅲ）,Ca(Ⅱ），Mg（Ⅱ）,Ni(Ⅱ）,Mn（Ⅱ),Cu(Ⅱ），Zn(Ⅱ），and Cd(Ⅱ） cause no interference on the determination of the analyzed ions by inductively-coupled plasma atomic emission spectrometry (ICP-AES).The static saturation adsorption capacities of the fiber for the analytes are in the range of 1.15-2.80mmol/g.The relative standard deviations for the determination of 20.0ng/mL each of Au(Ⅲ）,Pt(Ⅳ）,Pd(Ⅳ）and Ir(Ⅳ） are in the range of 0.7%-3.0%.The recoveries for test from standard additions to real solution samples are between 96% and 100%.The concentration of each ion in powder sample detected by the method is in good agreement with the certified value.     

Application of potassium ferricyanide in the spectrophotometric determination of captopril

A novel method for the determination of captopril by speetrophotometer is described in this paper. The experiment is based on the fact that Fe(Ⅲ) is reduced to Fe(Ⅱ) by captopril, then the in situ formed Fe(Ⅱ) reacts with potassium ferricyanide to give the soluble prussian blue at pH 4.00, and its maximal adsorption wavelength (λmax) is 735 nm. Good linear relationship is obtained between the absorbance and the concentration of captopril in the wide range of 0.05-20 μg/mL. The linear regression equation is A = -0.04314 + 0.11423C (μg/mL) with a correlation coefficient R = 0.9998. The detection limit (3a/k) is 0.04 μg/mL, the molar absorption coefficient is 2.5×104 L/mol cm. By mensurating the absorbance of soluble prussian blue, the indirect determination of eaptopril can be obtained. This method has been successfully applied to determination of captopril in pharmaceutical samples.Analytical results obtained are satisfactory.     

Fabrication of a Ho~(3+)-PVC membrane sensor based on N-phenyl-2-(thiophen-2-ylmethylene)hydrazinecarbothioamide for determination of holmium ions

In this research,a new poly（vinyl chloride）（PVC） membrane sensor for Ho³⁺ ion based on N-phenyl-2-（thiophen-2- ylmethylene）hydrazinecarbothioamide（PHC） as an ionophore was prepared.This sensor demonstrated good selectivity and sensitivity towards the holmium ion in comparison with variety of cations,including alkali,alkaline earth,transition and heavy metal ions.The effect of membrane composition and pH on the response properties of the electrode was investigated.In detail,the suggested sensor exhibited a Nernstian behavior(with a slope of 20.4±0.3 mV decade^-1) in the range of 1.0×10^-6 to 1.0×10^-2 mol/L with a detection limit of 6.2×10^-7 mol/L.The response time was relatively quick in the whole concentration range（～5 s）.The sensor usage was found to be at least 10 weeks in a pH range of 3.3-10.9.It was successfully applied in determination of fluoride ions in mouth wash preparations.     

Thiocyanate ion selective electrode based on bis(N-3-methylphenyl salicylidenaminato)copper(Ⅱ) ionophore

In this work a PVC membrane electrode based on bis(N-3-methyl phenyl salicylidenaminato)copper(II)as ionophore was prepared.The electrode was tested by inorganic anions and showed good selectivity for thiocyanate ion.This sensor showed Nerstian behavior with a slope of a-59.3 mV per decade at 25℃.The proposed electrode exhibited a wide linear range from 1.0 × 10~(-6) mol/L to 1.0× 10~(-1) mol/L with a detection limit of 5.0×10~(-7) mol/L.The electrode response was independent of pH in the range of 4.0-10.0.The response time is about 9-21s,and the electrode can be used for over 60 days without considerable deterioration.The prepared sensor was applied as an indicator electrode in potentiometric titration of SCN with Ag~+ ion and to determine the thiocyanate in samples of urine and saliva.     

SYNTHESIS AND CHARACTERIZATION OF ORGANSOLUBLE POLYIMIDE AND COPOLYIMIDES FROM ALICYCLIC DIANHYDRIDE

A kind of highly organsoluble polyimide and copolyimides were successfully synthesized from bicyclo（2.2.2）-oct- 7-ene-2,3,5,6-tetracarboxylic dianhydride （BCDA）, the commercial diamine 4,4＇-methylenedianiline （MDA） and the designed diamine 4,4＇-methylenebis-（2-tert-butylaniline） （MBTBA）. The polyimide from BCDA and MBTBA is highly soluble in conventional low boiling point solvents （such as chloroform, tetrahydrofuran） at room temperature. But the solubility of the copolyimides in conventional solvents decreased with the molar ratio of MBTBA and MDA decreased. When the molar ratio of MBTBA and MDA was larger than 7/3, the copolyimides can be soluble in low boiling point solvents at room temperature to form a transparent, flexible, tough film by solution casting. When the molar ratio of MBTBA and MDA was between 7/3 and 1/9, they can only be soluble in hot dipolar aprotic solvents （such as DMF, NMP etc.） and form films too. The copolyimide was only soluble in m-cresol when the molar ratio of MBTBA and MDA was lower than 1/9. The number-average molecular weights of the soluble copolyimides were larger than 5.8 × 1064 g/mol by GPC and their polydispersity indices were higher than 1.4. Only one glass transition temperature of these copolyimides was detected around 400℃ by DMA. The copolyimides did not show appreciable decomposition up to 430℃ in N2.     

Simultaneous Determination of Epinephrine, Noradrenaline and Dopamine in Human Serum Samples by High Performance Liquid Chromatography with Chemiluminescence Detection

A simple, rapid and accurate high performance liquid chromatographic （HPLC） technique coupled with chemiluminescence （CL） detection was developed for the simultaneous determination of epinephrine （E）, noradrenaline （NA） and dopamine （DA）. It was based on the analyte enhancement effect on the CL reaction between luminol and potassium ferricyanide. The effects of various parameters, such as potassium ferricyanide concentration, luminol concentration, pH value and component of the mobile phase on chromatographic behaviors of the analytes （E, NA and DA） were investigated. The separation was carded out on C18 column using the mobile phase of 0.01 mol/L potassium hydrogen phthalate solution and methanol （92 ： 8, V/V）. Under the optimum condi- tions, E, NA and DA showed good linear relationships in the range of 1 × 10^-8 -5 × 10^-6, 5.0× 10^-9 -1.0× 10^-6 and 5.0×10^-9-1.0× 10^-6 g]mL respectively. The detection limits for E, NA and DA were 4.0×10^-9, 1.0× 10^-9 and 8.0 × 10^-10 g/mL. The proposed method has been applied successfully to the analysis of E, NA and DA in human serum samples.     

Highly Selective Salicylate Membrane Electrode Based on N,N′-(Aminoethyl)ethylenediamide Bis(2-salicylideneimine)Binuclear Copper(Ⅱ) Complex as Neutral Carrier

A new ion selective electrode for salicylate based on N,N'-(aminoethyl)ethylenediamide bis(2-salicylideneimine)binuclear copper(Ⅱ)complex[Cu(Ⅱ)_2-AEBS]as an ionophore was developed.The electrode has a linear range from1.0×10~(-1) to 5.0×10~(-7) mol·L~(-1) with a near-Nernstian slope of(-55±1)mV/decade and a detection limit of 2.0×10~(-7) mol·L~(-1) in phosphorate buffer solution of pH 5.0 at 25℃.It shows good selectivity for Sal~- and displaysanti-Hofmeister selectivity seoquence:Sal~->SCN~->ClO_4~->I~->NO_2~->Br~->NO_3~->CI~->SO_3~(2-)>SO_4~(2-)The proposed sensor based on binuclear copper(Ⅱ)complex has a fast response time of 5-10 s and can be used forat least 2 months without any major deviation.The response mechanism is discussed in view of the alternating cur-rent(AC) impedance technique and the UV-vis spectroscopy technique.The effect of the electrode membranecompositions and the experimental conditions were studied.The electrode has been successfully used for the deter-mination of salicylate ion in drug pharmaceutical preparations.     

Simple,Selective,and Sensitive Spectrophotometric Method for Determination of Trace Amounts of Nickel(Ⅱ),Copper(Ⅱ), Cobalt(Ⅱ),and Iron(Ⅲ)with a Novel Reagent 2-Pyridine Carboxaldehyde Isonicotinyl Hydrazone

A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone(2-PYAINH)was synthesized and studied for the spectrophotometric determination of nickel,copper,cobalt,and iron in detail.At a pH value of 7.0,9.0,9.0,and 8.0,respectively,which greatly increased the selectivity;nickel,copper,cobalt, and iron reacted with 2-PYAINH to form a 1:2 yellow-orange,1:2 yellow-green,1:2 yellow and 1:1 yellow complexes,with absorption peaks at 363,352,346,and 359 nm,respectively.Under the optimal conditions,Beer's law was obeyed over the ranges of 0.01-1.4,0.01-1.5,0.01-2.7,and 0.01-5.4 mg/L,respectively.The apparent molar absorptivity and Sandell's sensitivities were 8.4×104,5.2x104,7.1×104,and 3.9×104L·mol-1.cm-1,respectively,and 0.00069,0.0012,0.00078,and 0.0014 μ g·cm-2,respectively.The detection limits were found to be 0.001,O.002,0.003,and 0.01 mg/L,respectively.The detailed study of various interfering ions to make the method more sensitive was carried out and selective and several real samples were analyzed with satisfactory results.     

Determination of Melatonin in Rat Pineal Gland and Drug with Flow-Injection Chemiluminescence

A flow-injection chemiluminescence （CL） method for the determination of melatonin based on the CL reaction of melatonin with hydrogen peroxide and sodium hypochlorite （NaOCl） in a basic alkaline solution was developed. The possible CL mechanism has been discussed, and a proposal for the reaction pathway was given that singlet oxygen was clarified to be produced in this reaction system and was responsible for the CL emission. Under the optimized conditions, the linear concentration range of application was 1.0×10^-7-2.5 × 10^-4 moloL-I with a de- tection limit of 5.0 ×10^-8 moloL-1 （S/N= 3）. The relative standard deviation for eight repeated measurements of 1.0×10^-6 mol·L^-1 melatonin was 2.8%. The interferences of several important biological substances, some indole compound, cations and anions were studied. No interference was found for the anions, glucose, starch, most of cations and low concentration （less than 3.0 × 10^-6 mol·L^-1） of some biological substances and indole compound. The method was applied to the determination of melatonin in rat pineal gland and drug with satisfactory results. The sample throughput was 90 injections per hour.     

4-(2-QUINOLYLAZO)-1, 3-DIHYDROXY-NAPHTHALENE——A NEW SENSITIVE ANALYTICAL REAGENT FOR TRACE COPPER DETERMINATION

The azo compound 4-(2-quinolylazo)-1,3-dihydroxynaphthalene (2-QADNm) has been synthesized and used as a new sensitive spectrophotometric and electroanalytical reagent for determination of trace amounts of copper. In dilute alkaline solutions, 2-QADNm shows a single-sweep polarographic wave at -0.95 V (vs. SCE). In the presence of copper(Ⅱ) two new waves appear at -0.52 and -0.79 V. Using the wave at-0.79 V, a trace amount of copper down to 10~(-8) mol/L can be determined. The electroanalytical characteristics of 2-QADNm and the electrochemical reaction mechanism of the copper(Ⅱ)-2-QADNm complex have been studied in detail by the use of various electrochemical techniques. In alkaline solutions, 2-QADNm forms red complex with copper(Ⅱ) which has an absorption peak at 526 nm, the molar absorptivity being 6.4×10~4 1·mol~(-1)·cm~(-1). In the presence of a non-ionic surfactant the molar absorptivity of this complex is 1.6×10~5 1·mol~(-1)·cm~(-1).