Total reflection X-ray fluorescence analysis of oral fluids of women affected by osteoporosis and osteopenia

Osteoporosis is a disease characterized by low bone mass and microarchitectural deterioration of bone tissue, leading to bone fragility and an increased susceptibility to fractures; the early stage of decreased bone density is called osteopenia. More than 200 million people are affected and about 50% of post-menopausic women are expected to develop the disease. Osteoporosis, osteopenia and periodontal disease have in common several risk factors, being hyperthyroidism and smoking habits the most important ones. There is scarce information in the literature about the association between periodontal disease and osteoporosis and/or osteopenia. Some works suggest that osteoporotic women are susceptible to a higher loss of periodontal insertion, alveolar bones, and teeth.     

Total reflection X-ray fluorescence mercury analysis after immobilization on quartz surfaces

Quartz reflectors are a common substrate for total reflection X-ray fluorescence (TXRF) analysis. Especially low masses of trace elements can be determined on these surfaces. In the present work, various complexing reagents were immobilized on the surface of quartz reflectors. The reflectors were immersed in mercury solutions and selective mercury collection took place. The effect of immersion time was examined and a few minutes were found adequate. The reflectors were analysed for mercury by TXRF. Different complexing reagents showed different collection capabilities; 4-(2-pyridazo-resorcinol) gave the best among them. The effect of various experimental parameters was examined like pH, interferences from other ions, etc. Mercury speciation was successfully tested by comparing inorganic mercury results with the methyl mercury ones. A very good selectivity for inorganic mercury was found. It was achieved very good linearity in the 1-500 ng mL⁻¹ mercury concentration range and the minimum detection limit was equal to 2.5 ng mL⁻¹.     

Quantitative determination on heavy metals in different stages of wine production by Total Reflection X-ray Fluorescence and Energy Dispersive X-ray Fluorescence: Comparison on two vineyards

The purpose of this study is to determine the elemental content, namely heavy metals, of samples of vine-leaves, grapes must and wine. In order to assess the influence of the vineyard age on the elemental content throughout the several stages of wine production, elemental determinations of trace elements were made on products obtained from two vineyards aged 6 and 14 years from Douro region. The elemental content of vine-leaves and grapes was determined by Energy Dispersive X-Ray Fluorescence (EDXRF), while analysis of the must and wine was performed by Total Reflection X-ray Fluorescence (TXRF).     

Analysis of mineral water from Brazil using total reflection X-ray fluorescence by synchrotron radiation

The total reflection X-ray fluorescence using synchrotron radiation (SRTXRF) has become a competitive technique for the determination of trace elements in samples that the concentrations are lower than 100 ng ml⁻¹. In this work, thirty-seven mineral waters commonly available in supermarkets of Rio de Janeiro, Brazil, were analyzed by SRTXRF. The measurements were performed at the X-Ray Fluorescence Beamline at Brazilian National Synchrotron Light Laboratory (LNLS), in Campinas, São Paulo, using a polychromatic beam with maximum energy of 20 keV for the excitation. Standard solutions with gallium as internal standard were prepared for calibration of the system. Mineral water samples of 10 μl were added to Perspex sample carrier, dried under infrared lamp and analyzed for 200 s measuring time. It was possible to determine the concentrations of the following elements: Si, S, K, Ca, Ti, Cr, Mn, Ni, Cu, Zn, Ge, Rb, Sr, Ba and Pb. The elemental concentration values were compared with the limits established by the Brazilian legislation.     

Total reflection X-ray fluorescence and grazing incidence X-ray spectrometry — Tools for micro- and surface analysis. A review

A review of Total Reflection X-ray Spectrometry and related methods covering literature of four decades is presented. History, theory, instrumentation, sample preparation, and applications are summarized and some examples are given. New developments and trends are discussed with respect to emerging nano-technologies in all fields of sciences.     

Method and mechanism of vapor phase treatment–total reflection X-ray fluorescence for trace element analysis on silicon wafer surface

Vapor phase treatment (VPT) is a pretreatment with hydrofluoric acid vapor to raise the sensitivity of total reflection X-ray fluorescence spectroscopy (TXRF) for trace metal analysis on silicon wafers. The International Organization for Standardization/Technical Committee 201/Working Group 2 (ISO/TC201/WG2) has been investigating the method to analyze 10⁹ atoms/cm² level of metallic contamination on the silicon wafer surface. Though VPT can enhance the TXRF signal intensity from the metallic contamination, it has turned out that the magnitude of the enhancement varies with the type of methods and the process conditions. In this study, approaches to increase TXRF intensity by VPT are investigated using a fuming chamber in an automated VPD instrument. Higher signal intensity can be obtained when condensation is formed on the sample surface in a humidifying atmosphere and with a decreasing stage temperature. Surface observations with SEM and AFM show that particles with ~ 4 μm in diameter are formed and unexpectedly they are dented from the top surface level.     

The determination of Fe,Zn and Pb in Zn-Pb ores by energy-dispersive X-ray fluorescence method

Energy dispersive X-ray fluorescence method for the determination of iron /3.5–26% of Fe/, zinc /0.5–9% of Zn/ and lead /0.05–5% of Pb/in zinc-lead ores containing arsenic has been worked out. In order to eliminate the interelement effect intensity correction equation had been proposed. The relative standard deviation of the determination varies from 3.6 to 9.2% depending on the element.     

Total reflection x-ray fluorescence as a sensitive analysis method for the investigation of sputtering processes

Angular distributions of sputtered germanium atoms during the grazing incidence of argon ions were investigated. Argon ion beams with angles of incidence of 75° and 80° and with ion energy of 20 keV were used in sputtering experiments. TXRF analysis showed to be an excellent method for measuring the angular distribution of sputtered atoms due to its low detection limit under total reflection conditions. The experimental data are compared to Monte-Carlo simulations. The observed differences are discussed, and suggestions for improving the Monte-Carlo simulation of ion sputtering are made.     

Total reflection X-ray fluorescence analysis of fly ash from Bulgarian coal-fired power plants

The contents of Cl, Ca, K, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Rb, Sr, Ba and Pb in raw coal fly ash from five Bulgarian power plants were determined by total reflection X-ray fluorescence (TXRF), using gallium as the internal standard. The samples were analysed as in slurry form in Triton? X-114. The experimental parameters, such as grain size, concentrations of fly ash slurry and excitation time were optimised. For validation of the method, the certified reference material BCR-176R fly ash was used. The precision of the results obtained is characterised by a relative standard deviation of approximately 10%. The resulting data confirm the suitability of TXRF for the simultaneous determination of major, minor and trace elements in coal fly ash samples. Further advantages provided by TXRF are easy sample preparation (no sample dissolution) and the small sample amount required for analysis.     

Total reflection X-ray fluorescence spectrometric determination of elements in water hyacinth from the Lerma River

The Lerma River is one of the most polluted body water in Mexico. For this reason, only the highly resistant organisms such as water hyacinth are able to reproduce in this river. The aim of this work was to evaluate the concentration of K, S, Fe, Ca, Mn, Ti, Zn, Sr, Rb, Cu, Cr, Ni, Pb and Br in roots of water hyacinth (Eichhornia crassipes) from the Lerma River. The samples were collected from five sites in the river and analyzed in triplicate using a TXRF Spectrometer ‘TX-2000 Ital Structures’ with a Si(Li) detector and a resolution of 140 eV (FWHM) at Mn Kα. A Mo tube (40 kV, 30 mA) with 17.4 KeV excitation energy was used for a counting time of 500 s. Results show that the average metal concentration in the water hyacinth roots decrease in the following order: K (9698.2 µg/g) > S (7593.3 µg/g) > Fe (4406.6 µg/g) > Ca (2601.8 µg/g) > Mn (604.2 µg/g) > Ti (230.7 µg/g) > Zn (51.65 µg/g) > Sr (43.55 µg/g) > Rb (18.61 µg/g) > Cu (12.78 µg/g) > Cr (6.45 µg/g) > Ni (4.68 µg/g) > Pb (4.32 µg/g) > Br (4.31 µg/g) and the bioconcentration factors in the water hyacinth decrease in the sequence: Ti > Fe > Mn > Cu > Ni > Zn > S > Pb > Rb > K > Cr > Sr > Br > Ca. The concentrations in roots of water hyacinth reflect the high pollution level of the river.     

Applicability of direct total reflection X-ray fluorescence analysis for selenium determination in solutions related to environmental and geochemical studies

A significant amount of environmental studies related to selenium determination in different environmental compartments have been published in the last years due to the narrow range between the Se nutritious requirement as essential element and toxic effects upon exposure. However, the direct analysis of complex liquid samples like natural waters and extraction solutions presents significant problems related to the low Se concentrations and the complicated matrix of this type of samples.     

Matrix effect on the detection limit and accuracy in total reflection X-ray fluorescence analysis of trace elements in environmental and biological samples

The effect of matrix contents on the detection limit of total reflection X-ray fluorescence analysis was experimentally investigated using a set of multielement standard solutions (500 ng/mL of each element) in variable concentrations of NH₄NO₃. It was found that high matrix concentration, i.e. 0.1–10% NH₄NO₃, had a strong effect on the detection limits for all investigated elements, whereas no effect was observed at lower matrix concentration, i.e. 0–0.1% NH₄NO₃.     

First combined total reflection X-ray fluorescence and grazing incidence X-ray absorption spectroscopy characterization of aeolian dust archived in Antarctica and Alpine deep ice cores

Aeolian mineral dust archived in polar and mid latitude ice cores represents a precious proxy for assessing environmental and climatic variations at different timescales. In this respect, the identification of dust mineralogy plays a key role. In this work we performed the first preliminary X-ray absorption spectroscopy (XAS) experiments on mineral dust particles extracted from Antarctic and from Alpine firn cores using grazing incidence geometry at the Fe K-edge. A dedicated high vacuum experimental chamber was set up for normal-incidence and total-reflection X-Ray Fluorescence and Absorption Spectroscopy analyses on minor amounts of mineral materials at the Stanford Synchrotron Radiation Laboratory. Results show that this experimental technique and protocol allows recognizing iron inclusion mineral fraction on insoluble dust in the 1–10 µg range.     

Trace metal analysis of sediments and particulate matter in sea water by energy-dispersive X-ray fluorescence

Summary The capability of energy-dispersive X-ray fluorescence was investigated for fast and simple chemical analysis of trace elements in sediments and particulate matter in sea water. Nuclepore 0.4 m pore-size membranes are recommended as optimal filters for a straightforward collection of suspended material. The collection of suspended trace metals by filtration seemed to give a sufficiently homogeneous filter load (s% <2.5). Data are presented on the concentrations of K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, Br, Pb, Rb and Sr with a fair precision (s% < 5.6) and accuracy.

---

Bestimmung von Metallspuren in Ablagerungen und Schwebstoffen von Meerwasser mit Hilfe der energiedispersiven Röntgenfluorescenz

Zusammenfassung Ein Verfahren zur raschen und einfachen Analyse der Metallspuren wird vorgeschlagen. Zur Sammlung der Schwebstoffe werden als optimal Nuclepore-Membranen (Porengröße 0,4 m) empfohlen. Dabei wird eine ausreichend homogene Filterbeladung erhalten (s% < 2,5). Mit befriedigender Reproduzierbarkeit (s% < 5,6) und Richtigkeit wurden folgende Elemente bestimmt: K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, Br, Pb, Rb und Sr.

     

Total reflection X-ray fluorescence analysis of trace-elements in candies marketed in Mexico

Trace metals concentrations in food are significant for nutrition, due either to their nature or toxicity. Sweets, including chewing gum and candies, are not exactly a food, but they usually are unwearied consumed by children, the most vulnerable age-group to any kind of metal contamination in the food chain. The presence of relatively high concentrations of heavy metals such as Lead elicits concern since children are highly susceptible to heavy metals poisoning. Trace-metals concentrations were determined for six different flavors of a Mexican candy by means of Total X-ray Fluorescence Spectrometry. Triplicate samples of the various candy's flavours (strawberry, pineapple, lemon, blackberry, orange and chilli) were digested in 8 mL of a mix of supra-pure HNO₃ and H₂O₂ (6 mL: 2 mL) in a microwave oven MARS-X. Results show the presence of essential and toxic elements such as Ti, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb, Sr, and Pb. All metal concentrations were higher and significantly different (α = 0.05) in chilli candy, compared to other candy flavours. Lead concentration fluctuated in the range of 0.102 to 0.342 μg g^− 1. A discussion about risk consumption and concentration allowed by Mexican and International Norms is made. As a part of the Quality Control Program, a NIST standard of “Citrus Leaves” and a blank were treated in the same way.     

Total reflection X-ray fluorescence analyses of samples from oil refining and chemical industries

The applicability and performance of the TXRF method for the analysis of sample materials from the oil refining and chemical industries were studied. One objective of the study was to develop rapid analytical procedures for the determination of elements present as traces in size fractionated diesel emission particles, in raw materials of resin production (ureas and phenols) and in trouble-shooting samples. Another goal was to determine the real, rather than the ideal, detection limits for the various applications. Absolute detection limits for most elements found in size fractionated diesel emission particles were below 1 ng. Relative detection limits determined for trace elements in ureas were between 5 and 30 μg kg⁻¹. Only the values for P, S and Ca exceeded this range. Additionally, remarkable differences in trace elements below 1 mg kg⁻¹ could be detected between five commercial ureas. © 1997 Elsevier Science B.V.     

Density–depth profiles of an As‐implanted Si wafer studied by repeated planar sputter etching and total reflection x‐ray fluorescence analysis

The implantation of a high dose of high‐energy ions into an Si wafer causes amorphization of the original monocrystalline structure within a near‐surface layer. The in‐depth distribution of both Si atoms of the wafer and As ions implanted at a dose of 1 × 10¹⁷ ions cm^?2 and an energy of 100 keV is studied. A novel method combining a repeated planar and broad sputter etching with differential weighing, surface analysis by total reflection x‐ray fluorescence and Tolansky interferometry is used for this investigation. Different depth profiles are recorded on the nanometre scale for the concentration defined as the mole ratio of As and Si, for the mass density of the implanted layer and for the number density of As and Si. The results generally correspond with measurements of Rutherford backscattering spectrometry and only deviate when the assumptions made for the mass density do not fit well. An appropriate approach to this quantity involves the number density of implanted ions but, furthermore, considers a variation of the number density of Si atoms during implantation, especially for a high dose and high‐energy implantation. The variation can be taken into account by a factor γ, where γ > 1 indicates compression and γ < 1 indicates extension of the original crystalline structure. For the above mentioned implantation, γ is measured separately for each sublayer to obtain accurate depth profiles. Copyright © 2003 John Wiley & Sons, Ltd.     

Characterization of Japanese color sticks by energy dispersive X-ray fluorescence,X-ray diffraction and Fourier transform infrared analysis

This work comprises the use of energy dispersive X-ray fluorescence (EDXRF), X-ray diffraction (XRD) and Fourier transformed infrared (FTIR) techniques for the study of the composition of twentieth century traditional Japanese color sticks. By using the combination of analytical techniques it was possible to obtain information on inorganic and organic pigments, binders and fillers present in the sticks. The colorant materials identified in the sticks were zinc and titanium white, chrome yellow, yellow and red ochre, vermillion, alizarin, indigo, Prussian and synthetic ultramarine blue. The results also showed that calcite and barite were used as inorganic mineral fillers while Arabic gum was the medium used. EDXRF offered great potential for such investigations since it allowed the identification of the elements present in the sample preserving its integrity. However, this information alone was not enough to clearly identify some of the materials in study and therefore it was necessary to use XRD and FTIR techniques.