Quantitative measurement of Q species in silicate and borosilicate glasses using Raman spectroscopy

Raman spectroscopy has been used to measure the fraction of tetrahedral silicate units connected at three corners into the network (Q³) in binary lithium silicate glasses and also in the more complex borosilicate glasses used for waste immobilization. Agreement within experimental error was obtained with ²⁹Si MAS NMR measurements of the same samples. Raman provides an alternative method of structural determination for silicon-containing glasses with a high content of paramagnetic species where NMR loses resolution. Analysis was performed on borosilicate glasses containing up to 11.98 mol% Fe₂O₃ and the Q³ values obtained by Raman spectroscopy agree within error with the published ²⁹Si NMR results from borosilicate glasses containing the equivalent quantity of Al₂O₃.     

Effect of boron addition on the structure and properties of iron phosphate glasses

Effects of boron addition on the glass forming characteristics, structure and properties of iron phosphate glasses with nominal compositions of xB₂O₃-(40−x)Fe₂O₃-60P₂O₅ (x = 2-20, mol%) and xB₂O₃-(100−x)[Fe₂O₃-60P₂O₅] (x = 2-20, mol%) have been investigated by DTA, XRD, IR and Mössbauer spectroscopy. Although there were some weak local surface crystallizations on especially most of the glasses in group B, all of the compositions formed glass. DTA spectra showed two exothermic peaks corresponding to crystallizations along with an endothermic glass transition peak. T_g increased with increasing B₂O₃ content for the glasses in the first series which indicates that the addition of B₂O₃ increases the thermal stability of glasses in this series while the opposite is observed in the second series. The dissolution rates of boron containing bulk glasses were found to be around 10⁻⁹ gr/cm² min which are comparable to that of the base iron phosphate glass. When the B₂O₃ content was above 14%, new bands related to BO₄ tetrahedral groups have been observed in the IR spectra. The Mössbauer isomer shift values of boron doped glasses were found to be a little lower than that of base glass but both iron ions had distorted octahedral coordination in all glasses. The fraction of Fe²⁺ ions in glasses (Fe²⁺/∑(Fe²⁺ + Fe³⁺)) was found to be 23% for the base glass while it was 10-22% for the boron doped glasses.     

Electronic relaxation in zinc iron phosphate glasses

The electrical and dielectric properties of 10ZnO-30Fe₂O₃-60P₂O₅ (mol%) glasses, melted at different temperatures were measured by impedance spectroscopy in the frequency range from 0.01 Hz to 3 MHz and over the temperature range from 303 to 473 K. It was shown that the dc conductivity strongly depends on the Fe(II)/[Fe(II) + Fe(III)] ratio. With increasing Fe(II) ion content from 17% to 37% in these glasses, the dc conductivity increases. Procedure of scaling conductivity data measured at various temperatures into a single master curve is given. The conductivity of the present glasses is made of conduction and conduction-related polarization of the polaron hopping between Fe(II) and Fe(III), both governed by the same relaxation time, τ. The high frequency dispersion in electrical conductivity arises from the distribution in τ caused by the disordered glass structure. The evolution of the complex permittivity as a function of frequency and temperature was investigated. At low frequency the dispersion was investigated in terms of dielectric loss. The thermal activated relaxation mechanism dominates the observed relaxation behavior. The relationship between relaxation parameters and electrical conductivity indicates the electronic conductivity controlled by polaron hopping between iron ions.     

Physical properties of lead iron phosphate glasses containing Cr2O3

The influence of Cr₂O₃ on glass forming characteristics and physical properties of PbO-Fe₂O₃-P₂O₅ glasses has been investigated by Raman and Mössbauer spectroscopies, X-ray diffraction analysis (XRD), Differential Thermal Analysis (DTA), Scanning Electron Microscopy (SEM) and impedance spectroscopy. Glasses of the general composition xCr₂O₃-(28.3-x)PbO-28.7Fe₂O₃-43.0P₂O₅, 0 ≤ × ≤ 10, (mol%) were prepared by conventional melt-quenching technique. The compositions containing up to 4 mol% Cr₂O₃ formed fully amorphous samples and their Raman spectra show systematic increase in the fraction of orthophosphate Q⁰ units with increasing Cr₂O₃ content and O/P ratio.On the other hand, compositions containing 8 and 10 mol% Cr₂O₃ partially crystallized during cooling and annealing to Fe₇(PO₄)₆, Fe₂Pb₃(PO₄)₄ and Cr₂Pb₃(PO₄)₄. A high tendency for crystallization of these melts is related to the high O/P (> 4) and Fe²⁺/Fe_tot (≈ 0.60) ratios.Electrical conductivity of xCr₂O₃-(28.3-x)PbO-28.7Fe₂O₃-43.0P₂O₅, 0 ≤ × ≤ 10, (mol%) compositions is independent of Cr₂O₃ and controlled entirely by the polaron transfer between Fe²⁺ and Fe³⁺ ions.     

Investigation of infrared emission and lifetime in Tm-doped 75TeO2:20ZnO:5Na2O (mol%) glasses: Effect of Ho and Yb co-doping

In this paper we describe fabrication and characterization of rare-earth-doped active tellurite glasses to be used as active laser media for fiber lasers emitting in the 2 μm region. The base composition is (mol%): 75TeO₂-20ZnO-5Na₂O with different concentrations of Tm³⁺, Yb³⁺ and Ho³⁺ as dopants or co-dopants. Optical properties of doped glasses were studied and pumping at 800 nm and at 980 nm were tested in order to compare the efficiency of two pumping mechanisms. Optical characterization carried out on glasses containing only Tm³⁺ ions indicated the optimum concentration of Tm₂O₃ in terms of emission efficiency as 1 wt%. The addition of 5 wt% of Yb₂O₃ to Tm³⁺-doped glasses led to the best results in terms of intensity of fluorescence emission and of lifetime values. Yb and Ho co-doped Tm-tellurite glass was measured in emission.     

Dielectric properties and structural features of barium-iron phosphate glasses

The dielectric constant of barium-iron phosphate glasses with the general composition (40−x)BaO · xFe₂O₃ · (60−x)P₂O₅ has been investigated at two fixed frequencies (100 kHz and 9.0 GHz). The dielectric constant measured using microwave technique, and the ratio O/P of these glasses increase with increasing Fe₂O₃ content. The structure and valence states of the iron ions in these glasses were investigated using Mössbauer spectroscopy, infrared spectroscopy and differential thermal analysis. Both Fe(II) and Fe(III) ions present in these glasses in octahedral coordination act as permanent dipoles, and the increase of the iron concentration increase these permanent dipoles, contributing to the dielectric constant.     

Elastic properties and structural studies on lead-boro-vanadate glasses

This paper describes elastic properties and spectroscopic studies on the xPbO-50B₂O₃-(50 - x)V₂O₅ (where x = 20, 25, 30, 35, 40, 45 and 49 mol%) glass system. Elastic moduli and spectroscopic parameters exhibit compositional dependent trends and the existence of characteristic borovanadate groups in these glasses. The bulk modulus and shear modulus increase with the concentration of [BO_4/2]⁻ and [B₂V₂O₉]²⁻ groups, which increases the dimensionality of the network. The scheme of modification of borate and vanadate groups has been explained by considering the Sanderson’s electronegativity principle. Analysis of infrared(IR) and magic angle spinning-nuclear magnetic resonance (MAS-NMR) spectra suggests the presence of characteristic diborovanadate groups also in these glasses. The results are examined in view of the structural groups formed due to the presence of PbO as a modifier.     

Structural investigation of bismuth borate glasses and crystalline phases

Glasses of the system: xBi₂O₃-(100−x)B₂O₃ (x = 20 to 66 mol%) were prepared and characterized by density, DSC, UV-visible absorption and ¹¹B MAS-NMR spectroscopy. Glass molar volume increases while the glass transition temperature decreases with Bi₂O₃ concentration. Densities of some bismuth borate glasses are found to be greater or very close to those of single crystal phases with equal composition. B¹¹ MAS-NMR studies determined that the fraction of tetrahedrally coordinated borons (N₄) is maximum at 42 mol% of Bi₂O₃ and that there is a local maxima in N₄ at Bi₂O₃ concentration of 50 mol%. Glasses containing Bi₂O₃ concentration of 33 mol% and higher show an unusual, intense absorption band just below the optical band gap. Two crystalline phases: Bi₃B₅O₁₂ and Bi₄B₂O₉ were prepared by devitrification of glasses and characterized by X-ray diffraction, FTIR and ¹¹B MAS-NMR studies. Both crystalline phases contained significantly lower N₄ than glasses with equal composition.     

Characterization of iron phosphate glasses prepared by microwave heating

Phosphate glasses have been prepared by melting batch materials in electric furnaces, induction furnaces, and in microwave ovens. In the present work mixtures of (NH₄)₂HPO₄ and Fe₃O₄ or Fe₂O₃ were exposed to microwave energy, heated to 1200 °C, and cast to produce iron phosphate glasses. Glasses were also produced in electric furnaces for comparison. The material was analyzed by X-ray diffraction, Mössbauer spectroscopy, and differential thermal analysis. For magnetite-based glasses produced in an electric furnace, the Fe²⁺/(Fe²⁺ + Fe³⁺) ratio is compatible with the value in the batch material. The Fe²⁺/(Fe²⁺ + Fe³⁺) ratio is higher for glasses produced in a microwave oven. Glasses with nominal composition 55Fe₃O₄–45P₂O₅ (mol%) produced in an electric furnace present an arranged magnetic phase with hyperfine field that could be associated to hematite (estimated to be 21%). All the glasses submitted to heat treatments for crystallization present the following crystalline phases: FePO₄, Fe₃(PO₄)₂, Fe(PO₃)₃, Fe(PO₃)₂ and Fe₇(PO₄)₆. The amount of these phases depends on the glass composition, and glass preparation procedure. Microwave heating allows to reach melting temperatures at high heating rates, making the procedure easy and economical, but care should be taken concerning the final Fe²⁺/(Fe²⁺ + Fe³⁺) ratio.     

Deep-UV Raman spectroscopic analysis of structure and dissolution rates of silica-rich sodium borosilicate glasses

As part of ongoing studies to evaluate relationships between structure and rates of dissolution of silicate glasses in aqueous media, sodium borosilicate glasses of composition Na₂O·xB₂O₃·(3 − x)SiO₂, with x ≤ 1 (Na₂O/B₂O₃ ratio ≥ 1), were analyzed using deep-UV Raman spectroscopy. Results were quantified in terms of the fraction of SiO₄ tetrahedra with one non-bridging oxygen (Q³) and then correlated with Na₂O and B₂O₃ content. The Q³ fraction was found to increase with increasing Na₂O content, in agreement with studies on related glasses, and, as long as the value of x was not too high, this contributed to higher rates of dissolution in single pass flow-through testing. In contrast, dissolution rates were less strongly determined by the Q³ fraction when the value of x was near unity, and appeared to grow larger upon further reduction of the Q³ fraction. Results were interpreted to indicate the increasingly important role of network hydrolysis in the glass dissolution mechanism as the BO₄ tetrahedron replaces the Q³ unit as the charge-compensating structure for Na⁺ ions. Finally, the use of deep-UV Raman spectroscopy was found to be advantageous in studying finely powdered glasses in cases where visible Raman spectroscopy suffered from weak Raman scattering and fluorescence interference.     

Dielectric behavior and impedance spectroscopy of bismuth iron phosphate glasses

The electrical and dielectrical properties of Bi₂O₃–Fe₂O₃–P₂O₅ glasses were measured by impedance spectroscopy in the frequency range from 0.01 Hz to 4 MHz and over the temperature range from 303 to 473 K. It was shown that the dc conductivity strongly depends on the Fe₂O₃ content and Fe(II)/Fe_tot ratio. With increasing Fe(II) ion content from 17% to 34% in the bismuth-free 39.4Fe₂O₃–59.6P₂O₅ and 9.8Bi₂O₃–31.7Fe₂O₃–58.5P₂O₅ glasses, the dc conductivity increases. On the other hand, the decrease in dc conductivity for the glasses with 18.9 mol% Bi₂O₃ is attributed to the decrease in Fe₂O₃ content from 31.7 to 23.5 mol%, which indicates that the conductivity for these glasses depends on Fe₂O₃ content. The conductivity for these glasses is independent of the Bi₂O₃ content and arises mainly from polaron hopping between Fe(II) and Fe(III) ions suggesting an electronic conduction. The evolution of the complex permittivity as a function of frequency and temperature was investigated. At low frequency the dispersion was investigated in terms of dielectric loss. The thermal activated relaxation mechanism dominates the observed relaxation behavior. The relationship between relaxation parameters and electrical conductivity indicates the electronic conductivity controlled by polaron hopping between iron ions. The Raman spectra show that the addition of up to 18.9 mol% of Bi₂O₃ does not produce any changes in the glass structure which consists predominantly of pyrophosphate units.     

Electron spin resonance and magnetic studies on CaO-SiO2-P2O5-Na2O-Fe2O3 glasses

Room temperature electron spin resonance (ESR) spectra and temperature dependent magnetic susceptibility measurements have been performed to investigate the effect of iron ions in 41CaO · (52 − x)SiO₂ · 4P₂O₅ · xFe₂O₃ · 3Na₂O (2 ? x ? 10 mol%) glasses. The ESR spectra of the glass exhibited the absorptions centered at g ≈ 2.1 and g ≈ 4.3. The variation of the intensity and linewidth of these absorption lines with composition has been interpreted in terms of variation in the concentration of the Fe²⁺ and Fe³⁺ in the glass and the interaction between the iron ions. The magnetic susceptibility data were used to obtain information on the relative concentration and interaction between the iron ions in the glass.     

Mössbauer and optical spectroscopic study of temperature and redox effects on iron local environments in a Fe-doped (0.5 mol% Fe2O3) 18Na2O-72SiO2 glass

Local environments of ferric and ferrous irons were systematically studied with Mössbauer (at liquid helium temperature) and ultraviolet-visible-near infrared spectroscopic methods for various 18Na₂O-72SiO₂ glasses doped with 0.5 mol% Fe₂O₃. These were prepared at temperatures of 1300-1600 °C in ambient air or at 1500 °C under reducing conditions with oxygen partial pressures from 12.3 to 0.27×10⁻⁷ atmospheres. The Mössbauer spectroscopic method identified three types of local environments, which were represented by the Fe³⁺ sextet, the Fe³⁺ doublet, and the Fe²⁺ doublet. The Fe³⁺ sextet ions were assigned to ‘isolated’ octahedral ions. Under reducing conditions, the octahedral Fe³⁺ ions were readily converted into octahedral ferrous ions. The Fe³⁺ doublet exists both in octahedral and tetrahedral environment, mainly as tetrahedral sites in the reduced samples. The tetrahedral ions were found stable against reduction to ferrous ions. The Fe²⁺ doublet sites existed in octahedral coordination. Combining results from both spectroscopic studies, the 1120- and 2020-nm optical bands were assigned to octahedral ferrous ions with a different degree of distortion rather than different coordinations. Further, we assigned the 375-nm band to the transition of octahedral ferric ions that are sensitive to the change of oxygen partial pressure in glass melting and 415-, 435-, and 485-nm bands to the transitions of the tetrahedral ferric ions that are insensitive to oxidation states of the melt. The effect of ferric and ferrous ions with different coordination environments on the glass immiscibility was elucidated.     

Molecular dynamics simulations of calcium aluminate glasses

Molecular dynamics simulations of a series of calcium aluminate glasses have been carried out using empirical potentials with a covalent term. The simulations closely reproduce the total neutron correlation function of glasses with 30 and 38 mol% Al₂O₃ and physical properties such as elastic constants. For compositions close to the eutectic 37 mol% Al₂O₃, aluminum is tetrahedrally coordinated by oxygen, but the proportion of five-fold and six-fold coordination and also edge-sharing tetrahedra gradually increases with increasing Al₂O₃ content. The coordination number for oxygen around calcium atoms is close to 6 and this involves a larger coordination at a shorter, well-defined distance, followed by a smaller coordination with a broader range of distances. When the Al₂O₃ content decreases, the calcium aluminate structure becomes depolymerised and the average ring size increases. Also reported is an X-ray photoelectron spectroscopy measurement on a glass sample with 38 mol% Al₂O₃, which shows that 38.6 ± 0.9% of the oxygens are non-bridging, in excellent agreement with the simulations.     

Investigation of near constant loss contribution to conductivity in lithium bismo-silicate glasses

Glasses having compositions 20Li₂O · (80 − x)Bi₂O₃ · xSiO₂ (x = 55, 60, 65, 70 mol%) were investigated using impedance spectroscopy in the frequency range from 20 Hz to 1 MHz and in the temperature range from 543 to 663 K. The ac and dc conductivities, activation energy of the dc conductivity and relaxation frequency are extracted from the impedance spectra. The increase in conductivity with increase in SiO₂ content is attributed to the change in the structural units of bismuth. Both electric modulus and the conductivity formalism have been employed to study the relaxation dynamics of charge carriers in these glasses. A single ‘master curve’ for normalized plots of all the modulus isotherms observed for a given composition indicates the temperature independence of the dynamic processes for ions in these glasses. Similar values of activation energy for dc conduction and for conductivity relaxation time indicates that the ions overcome same energy barrier while conducting and relaxing. The observed conductivity spectra follows power law with exponent ‘s’ which increases regularly with frequency and approaches unity at higher frequencies. Near constant losses (NCL) characterize this linearly dependent region of conductivity spectra. A deviation from ‘super curve’ for various isotherms of conductivity spectra was also observed in high frequency region and at low temperatures, which supports the existence of different dynamic processes like NCL in addition to the ion hopping processes in the investigated glass system.     

Spectroscopic investigation and optical characterization of novel highly thulium doped tellurite glasses

In this paper, optical properties of 75TeO₂-20ZnO-5Na₂O host glass doped with concentration of Tm³⁺ up to 10 %mol were studied in order to assess the most suitable rare earth content for short cavity fiber lasers. Raman spectroscopy revealed a change in the glass structure while increasing Tm³⁺ content, similar to the well known addition of alkali ions in a glass. Influence of the fabrication process on the OH⁻ content was determined by FTIR measurements. Refractive index of Tm³⁺ doped tellurite glasses was measured at five different wavelengths ranging from 533 nm to 1533 nm. Lifetime and emission spectra measurements of the Tm³⁺ doped tellurite glasses are reported.     

Electric conductivity of glasses in the system Na2O/CaO/SiO2/Fe2O3

The addition of polyvalent transition metal ions to the usually insulating traditional soda-lime-silica glasses can lead to semiconducting properties. We report on synthesis of glasses and glass-ceramics in a soda-lime-silicate based system containing Fe₂O₃ in the concentration range from 5 to 30 mol%. Two sub-systems were considered, in one of them the ratio [Na₂O]/[Fe₂O₃] was varied while in the other one, the ratio [SiO₂]/[Fe₂O₃] was changed. The phase composition of the synthesized products was characterized by X-ray diffraction and energy dispersive X-ray analysis, while the electrical properties were studied by impedance spectroscopy. Partially crystallized non-reduced samples are semiconducting even at room temperature while the glassy samples (both reduced and non-reduced) exhibit semiconducting properties at temperatures equal or larger than 100 °C. An attempt is done to predict the physical approximation explaining the conduction process in the glasses.     

Structure and electrical conductivity of new Li2O-CeO2-B2O3 glasses

Fourier transformation infrared spectra, density and DC electrical conductivity of 30Li₂O · xCeO₂⋅(70 − x)B₂O₃ glasses, where x ranged between 0 and 15 mol%, have been investigated. The results suggested that CeO₂ plays the role of network modifier up to 7.5 mol%. At higher concentrations it plays a dual role; where most of ceria plays the role of network former. The density was observed to increase with increasing CeO₂ content. The effect on density of the oxides in the glasses investigated is in the succession: B₂O₃ < Li₂O < CeO₂. Most of CeO₂ content was found to be associated with B₂O₃ network to convert BO₃ into B O₄⁻ units. The contribution of Li⁺ ions in the conduction process is much more than that due to small polarons. The conductivity of the glasses is mostly controlled by the Li⁺ ions concentration rather than the activation energy for CeO₂ > 5 mol%. Lower than 5 mol% CeO₂ the conductivity is controlled by both factors. The dependence of W on BO₄⁻ content supports the idea of ionic conduction in these glasses.     

Electronic conductivity in zinc iron phosphate glasses

The electrical properties of (40−x)ZnO–xFe₂O₃–60P₂O₅ (x = 10, 20, 30 mol%) glasses were measured by impedance spectroscopy in the frequency from 0.01 Hz to 4 MHz and the temperature range from 303 to 473 K. It was shown that the dc conductivity strongly depends on the Fe₂O₃ content and Fe(II)/Fe_tot ratio. The increase in dc conductivity for these glasses is attributed to the increase in Fe₂O₃ content from 10 to 30 mol%. With increasing Fe(II) ion content from 6% to 17% the dc conductivity increases. This indicated that the conductivity arises mainly from polaron hopping between Fe(II) and Fe(III) ions suggesting an electron conduction in these glasses. By applying scaling on conductivity data measured at different temperatures, single master curve was obtained for each glass. On the other hand, deviation from the master curve at high frequencies was observed for glasses with different compositions. This deviation originates from a various mobility of charge carriers in different glass structures. Raman spectra showed the change of structure, from metaphosphate to pyrophosphate, with increasing Fe₂O₃ content from 10 to 30 mol%.     

The structure and optical properties of GeO2-GeS2 glasses

Oxy-chalcogenide glasses with compositions of xGeO₂-(100 − x)GeS₂, where 0 ? x ? 100 mol%, have been prepared and studied in terms of their structures and optical properties. X-ray fluorescence spectroscopy shows that Ge:S ratio can deviate from GeS₂ by ∼10 at.%, depending critically upon the preparation conditions. Raman scattering spectroscopy suggests that stoichiometric GeO₂-GeS₂ glasses have a heterogeneous structure in the scale of 1-100 nm. The optical gaps are nearly constant at 3.0-3.5 eV for glasses with 0 ? x ? 80 mol% and abruptly increase to ∼6 eV in GeO₂. This dependence suggests that the optical gap is governed by GeS₂ clusters, which are isolated and/or percolated. Composition-deviated glasses appear as orange and brown, and these glasses seem to have more inhomogeneous structures.