Thermo-optic properties of B2O3 doped Li2O-Al2O3-SiO2 glass-ceramics

Reduction in the temperature coefficient of the optical path length, dS/dT of Li₂O-Al₂O₃-SiO₂ glass-ceramics with near-zero thermal expansion coefficient was attempted using control of the temperature coefficient of electronic polarizability, ?, and the thermal expansion coefficient, α. The dS/dT value of 2.6 mol% B₂O₃-doped glass-ceramic was 12.5  × 10⁻⁶/°C, which was 0.9 ×  10⁻⁶/°C smaller than that of B₂O₃-free glass-ceramic. On the other hand, reduction in dS/dT through B₂O₃ doping was not confirmed in precursor glasses. Results showed that reduction in dS/dT of the glass-ceramic through B₂O₃ doping is caused by the reduction in ?. The reduction in ? from B₂O₃ doping was probably attributable to numerical reduction in non-bridging oxide ions with larger ? value by the concentration of boron ions in the residual glass phase. In addition, application of hydrostatic pressure during crystallization was effective to inhibit precipitation of β-spodumene solid solution, which thereby decreases dS/dT. The dS/dT value of B₂O₃-doped glass-ceramic crystallized under 196 MPa was 11.7 ×  10⁻⁶/°C. That value was slightly larger than that of silica glass. The α value of this glass-ceramic was smaller than that of silica glass.     

The glass transition temperature and infrared absorption spectra of: (70−x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Glasses of the system: (70−x) TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by melt quench technique. Dependencies of their glass transition temperatures (T_g) and infrared (IR) absorption spectra on composition were investigated. It is found that the gradual replacement of oxides, TeO₂ by Li₂O, decreases the glass transition temperature and increases the fragility of the glasses. Also, IR spectra revealed broad weak and strong absorption bands in the investigated range of wave numbers from 4000 to 400 cm⁻¹. These bands were assigned to their corresponding bond modes of vibration with relation to the glass structure.     

Role of nickel ion coordination on spectroscopic and dielectric properties of ZnF2-As2O3-TeO2:NiO glass system

20ZnF₂-30As₂O₃-(50 − x)TeO₂:xNiO (0 ≤ x ≤ 2.0) glasses were synthesized. The glasses were characterized by X-ray diffraction, scanning electron microscopy, EDS and DSC techniques. A variety of properties, i.e. optical absorption, infrared, magnetic susceptibilities and dielectric properties (constant ?′, loss tan δ, a.c. conductivity σ_ac over a wide range of frequency and temperature) of these glasses have been carried out. The analysis of results of all these studies has indicated that the nickel ions occupy both octahedral and tetrahedral positions and the gradual increase of NiO content in the glass matrix causes growing proportions of Ni²⁺ ions that occupy octahedral positions. The luminescence spectra of these glasses have exhibited a broad emission band in region 1200-1450 nm identified due to ³T₂(3F) → ³A₂(3F) octahedral transition of Ni²⁺ ions. The luminescence efficiency and cross section have been found to be the highest for the glass containing highest concentration of NiO. Finally it is concluded that the higher the concentration of octahedrally positioned Ni²⁺ ions, the higher is the luminescence efficiency.     

Spectroscopic properties of Er-doped Na2O-Sb2O3-B2O3-SiO2 glasses

Spectroscopic properties of Er³⁺-doped Na₂O-Sb₂O₃-B₂O₃-SiO₂ glasses have been investigated for developing 1.5-μm broadband fiber amplifiers. An intense 1.5-μm near infrared emission with a broad full width at half maximum (FWHM) of 88 nm has been obtained for Er³⁺-doped 5Na₂O-20Sb₂O₃-35B₂O₃-40SiO₂ glass upon excitation with a 980 nm laser diode. The obtained emission cross-section of the ⁴I_13/2 → ⁴I_15/2 transition and the lifetime of the ⁴I_13/2 level of Er³⁺ ions are 6.8 × 10⁻²¹ cm² and 0.36 ms, respectively. It is noted that the product of the emission cross-section and the FWHM of the glass, σ_e × FWHM, is as great as 598.4 × 10⁻²¹ cm² nm, which is comparable or higher than that of Er³⁺-doped bismuth-based and tellurite-based glasses. These special optical properties encourage in identifying them as important materials for potential applications in high performance optics and optical communication networks.     

Electron spin resonance and magnetic studies on CaO-SiO2-P2O5-Na2O-Fe2O3 glasses

Room temperature electron spin resonance (ESR) spectra and temperature dependent magnetic susceptibility measurements have been performed to investigate the effect of iron ions in 41CaO · (52 − x)SiO₂ · 4P₂O₅ · xFe₂O₃ · 3Na₂O (2 ? x ? 10 mol%) glasses. The ESR spectra of the glass exhibited the absorptions centered at g ≈ 2.1 and g ≈ 4.3. The variation of the intensity and linewidth of these absorption lines with composition has been interpreted in terms of variation in the concentration of the Fe²⁺ and Fe³⁺ in the glass and the interaction between the iron ions. The magnetic susceptibility data were used to obtain information on the relative concentration and interaction between the iron ions in the glass.     

Structure and electrical conductivity of new Li2O-CeO2-B2O3 glasses

Fourier transformation infrared spectra, density and DC electrical conductivity of 30Li₂O · xCeO₂⋅(70 − x)B₂O₃ glasses, where x ranged between 0 and 15 mol%, have been investigated. The results suggested that CeO₂ plays the role of network modifier up to 7.5 mol%. At higher concentrations it plays a dual role; where most of ceria plays the role of network former. The density was observed to increase with increasing CeO₂ content. The effect on density of the oxides in the glasses investigated is in the succession: B₂O₃ < Li₂O < CeO₂. Most of CeO₂ content was found to be associated with B₂O₃ network to convert BO₃ into B O₄⁻ units. The contribution of Li⁺ ions in the conduction process is much more than that due to small polarons. The conductivity of the glasses is mostly controlled by the Li⁺ ions concentration rather than the activation energy for CeO₂ > 5 mol%. Lower than 5 mol% CeO₂ the conductivity is controlled by both factors. The dependence of W on BO₄⁻ content supports the idea of ionic conduction in these glasses.     

Studies of some mechanical and optical properties of: (70 − x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Specimens of the glassy system: (70 − x)TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by the melt-quenching. An ultrasonic pulse-echo technique was employed, at 5 MHz, for measuring: the ultrasonic attenuation, longitudinal and shear wave velocities, elastic moduli, Poisson ratio, Debye temperature and hardness of the present glasses. It is found that the gradual replacement of TeO₂ by Li₂O in the glass matrix up to 30 mol% leads to decrease the average crosslink density and rigidity of prepared samples which affects the properties, i.e., the hardness, ultrasonic wave velocities and elastic moduli are decreased, while the Poisson ratio and the ultrasonic attenuation are increased. Also, optical absorption spectra were recorded in the range, 200-800 nm for these glasses. The obtained results showed that a gradual shift in the fundamental absorption edge toward longer wavelengths occurred. Values of both of the optical energy gap, E_opt, and width tails, ΔE, are determined. It is observed that E_opt is decreased and ΔE increased with the increase of Li₂O in the glass matrix up to 30 mol%. The compositional dependences of the above properties are discussed and correlated to the structure of tested glasses.     

The dielectric behavior of a thermoelectric treated B2O3-Li2O-Nb2O5 glass

A transparent glass with the composition 60B₂O₃-30Li₂O-10Nb₂O₅ (mol%) was prepared by the melt-quenching technique. Glass-ceramics, containing LiNbO₃ ferroelectric crystallites, were obtained by heat-treatment (HT) above 500 °C, with and without the presence of an external electric field. The dielectric properties of the glass and glass-ceramic were investigated, as a function of temperature (270-315 K), in the 10 mHz-32 MHz frequency range. The presence of an external electric field, during the heating process, improves the formation of LiNbO₃ crystallites. The rise of the treatment temperature and the applied field, during the heat-treatment, leads to a decrease in the dc electric conductivity (σ_dc), indicating a decrease of the charge carriers number. The dielectric permittivity (ε′) values (300 K;1 kHz) are between 16.25 and 18.83, with the exception of the 550 °C HT sample that presents a ε′ value of 11.25. An electric equivalent circuit composed by an R in parallel with a CPE element was used to adjust the dielectric data. The results reflect the important role carried out by the heat-treatment and the electric field during the HT in the electric properties of glass-ceramics.     

Investigation of infrared emission and lifetime in Tm-doped 75TeO2:20ZnO:5Na2O (mol%) glasses: Effect of Ho and Yb co-doping

In this paper we describe fabrication and characterization of rare-earth-doped active tellurite glasses to be used as active laser media for fiber lasers emitting in the 2 μm region. The base composition is (mol%): 75TeO₂-20ZnO-5Na₂O with different concentrations of Tm³⁺, Yb³⁺ and Ho³⁺ as dopants or co-dopants. Optical properties of doped glasses were studied and pumping at 800 nm and at 980 nm were tested in order to compare the efficiency of two pumping mechanisms. Optical characterization carried out on glasses containing only Tm³⁺ ions indicated the optimum concentration of Tm₂O₃ in terms of emission efficiency as 1 wt%. The addition of 5 wt% of Yb₂O₃ to Tm³⁺-doped glasses led to the best results in terms of intensity of fluorescence emission and of lifetime values. Yb and Ho co-doped Tm-tellurite glass was measured in emission.     

Fabrication and properties of novel low-melting glasses in the ternary system ZnO-Sb2O3-P2O5

Glasses in the ternary system ZnO-Sb₂O₃-P₂O₅ were investigated as potential alternatives to lead based glasses for low temperature applications. The glass-forming region of ZnO-Sb₂O₃-P₂O₅ system has been determined. Structure and properties of the glasses with the composition (60 − x)ZnO-xSb₂O₃-40P₂O₅ were characterized by infrared spectra (IR), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results of IR indicated the role of Sb³⁺ as participant in glass network structure, which was supported by the monotonic and remarkable increase of density (ρ) and molar volume (V_M) with increasing Sb₂O₃ content. Glass transition temperature (T_g) and thermal stability decreased, and coefficient of thermal expansion (α) increased with the substitution of Sb₂O₃ for ZnO in the range of 0-50 mol%. XRD pattern of the heat treated glass containing 30 mol% Sb₂O₃ indicated that the structure of antimony-phosphate becomes dominant. The improved water durability of these glasses is consistent with the replacement of easily hydrated phosphate chains by corrosion resistant P-O-Sb bonds. The glasses containing ?30 mol% Sb₂O₃ possess lower T_g (<400 °C) and better water durability, which could be alternatives to lead based glasses for practical applications with further composition improvement.     

Thermal, chemical, optical properties and structure of Er-doped and Er/Yb-codoped P2O5-Al2O3-ZnO glasses

This study was explored in series of the optical, thermal, and structure properties based on 60P₂O₅-10Al₂O₃-30ZnO (PAZ) glasses system that doped with varied rare-earth (RE) elements Yb₂O₃/Er₂O₃. The glass transition temperature, softening temperature and chemical durability were increased with RE-doping concentrations increasing, whereas thermal expansion coefficient was decreased. In the optical properties, the absorption and emission intensities also increase with RE-doping concentrations increasing, When Er₂O₃ and Yb₂O₃ concentrations are over than 3 mol% in the Er³⁺-doped PAZ system and Yb³⁺-doped concentration is over than 3 mol% for Er³⁺/Yb³⁺-codoped PAZ system, the emission intensity significantly decreases presumably due to concentration quenching, formation of the ions clustering, and OH⁻ groups in the glasses network. It is suggested that the maximum emission cross-section (σ_e) is 7.64 × 10^− 21 cm² at 1535 nm is observed for 3 mol% Er³⁺-doped PAZ glasses. Moreover, the maximum σ_e × full-width-at-half-maximum is 327.8 for 5 mol% Er³⁺-doped PAZ glasses.     

Physicochemical studies of phosphate based P2O5-Na2O-CaO-TiO2 glasses for biomedical applications

Glasses P₂O₅-Na₂O-CaO-TiO₂ with different TiO₂ contents and fixed P₂O₅ (45 wt%) and CaO (24 wt%) have been prepared employing the normal melting and annealing technique. Measurements such as ultrasonic velocity, attenuation, solubility and pH have been carried out in all the compositions of the glasses. It is interesting to note that the above measured ultrasonic parameters exhibit an abnormal behavior (minimum) at 0.5 wt% of TiO₂ content, beyond which an increase in these parameters with increasing TiO₂ content is observed. The maximum pH values and Ca²⁺ ion release have been observed for the TiO₂ free glass those compositions with and the low TiO₂(?1.0 wt%) content. As the content of the TiO₂ increases, the solubility of the glasses decreases. The observed weight loss reveals two stages of phosphate dissolution kinetics i.e. the first stage, in which the weight loss is proportional to t^1/2, and a second stage in which a linear behavior is observed.     

Structure and non-linear optical performance of TeO2-Nb2O5-ZnO glasses

The non-linear optical performance and structure of TeO₂-Nb₂O₅-ZnO glasses was investigated as a function of ZnO content. The third-order non-linear optical susceptibility (χ⁽³⁾) as measured by a Degenerate Four Wave Mixing (DFWM) method, initially increased with increasing ZnO content to about 8.2 × 10⁻¹³ esu for a glass containing 2.5 wt% ZnO, and then decreased to 5.9 × 10⁻¹³ esu as the ZnO content increased to 10 wt%. There was no noticeable change as the ZnO content increased from 10 to 15 wt%. The non-linear optical response time, which caused electron cloud deformation, was from 450 to 500 fs. The structure of these glasses as analyzed by Raman spectroscopy and FT-IR spectra, was affected by the addition of ZnO up to 5 wt%, when, it is believed, the Zn²⁺ ions occupied the interstitial positions in the glass network by replacing the Nb⁵⁺ ions. The replaced Nb⁵⁺ ions occupied the network forming positions as the Te⁴⁺ ions. Increasing ZnO > 5 wt% did not have any further effect on the glass structure.     

The comparative structure, properties, and ionic conductivity of LiI + Li2S + GeS2 glasses doped with Ga2S3 and La2S3

The well known and characterized fast ion conducting (FIC) LiI + Li₂S + GeS₂ glass-forming system has been further optimized for higher ionic conductivity and improved thermal and chemical stability required for next generation solid electrolyte applications by doping with Ga₂S₃ and La₂S₃. These trivalent dopants are expected to eliminate terminal and non-bridging sulfur (NBS) anions thereby increasing the network connectivity while at the same time increasing the Li⁺ ion conductivity by creating lower basicity [(Ga or La)S_4/2]⁻ anion sites. Consistent with the finding that the glass-forming range for the Ga₂S₃ doped compositions is larger than that for the La₂S₃ compositions, the addition of Ga₂S₃ is found to eliminate NBS units to create bridging sulfur (BS) units that not only gives an improvement to the thermal stability, but also maintains and in some cases increases the ionic conductivity. The compositions with the highest Ga₂S₃ content showed the highest T_gs of ∼325 °C. The addition of La₂S₃ to the base glasses, by comparison, is found to create NBS by forming high coordination octahedral LaS₆³⁻ sites, but yet still improved the chemical stability of the glass in dry air and retained its high ionic conductivity and thermal stability. Significantly, at comparable concentrations of Li₂S and Ga₂S₃ or La₂S₃, the La₂S₃-doped glasses showed the higher conductivities. The addition of the LiI to the glass compositions not only improved the glass-forming ability of the compositions, but also increased the ionic conductivity glasses. LiI concentrations from 0 to 40 mol% improved the conductivities of the Ga₂S₃ glasses from ∼10⁻⁵ to ∼10⁻³ (Ω cm)⁻¹ and of the La₂S₃ glasses from ∼10⁻⁴ to ∼10⁻³ (Ω cm)⁻¹ at room temperature. A maximum conductivity of ∼10⁻³ (Ω cm)⁻¹ at room temperature was observed for all of the glasses and this value is comparable to some of the best Li ion conductors in a sulfide glass system. Yet these new compositions are markedly more thermally and chemically stable than most Li⁺ ion conducting sulfide glasses. LiI additions decreased the T_gs and T_cs of the glasses, but increased the stability towards crystallization (T_c − T_g).     

Ionic conductivity of Li2O-BaO-Bi2O3 glasses

Dc and ac conductivities of Li₂O-BaO-Bi₂O₃ glasses have been studied in a temperature range of 263-523 K and a frequency range of 10 Hz-2 MHz and have been compared with those of binary Li₂O-Bi₂O₃ glasses. The frequency dependent conductivity has been studied employing both the modulus and conductivity formalisms. We have observed small changes in the dc conductivity and its activation energy from those of the binary glass when content of BaO is small. However we have observed noticeable changes in the conductivity and the activation energy when BaO content is large. The significant changes in the values of the non-exponential parameter and the power-law exponent of the ac electrical properties have been observed due to introduction of BaO in the lithium bismuthate glasses. The existing relation between the power-law exponent and the non-exponential parameter was also violated in the present glass compositions.     

Optical Properties of Bi2O3-TeO2-B2O3 Glasses

Glasses of the Bi₂O₃-TeO₂-B₂O₃ ternary system were developed and their linear and nonlinear optical properties were investigated. The absorption edges of these glasses were found to be 367-384 nm with a good transmittance in visible wavelength, although they exhibit the refractive indices as high as 1.98-2.12 at 633 nm. The absorption edges are quite steep and they are analyzed by the Urbach theory. The obtained Urbach energies of these glasses are 73-79 meV which are comparable to silica glasses. The high refractive index and its glass composition dependency are discussed according to the basics of the electronic polarizability and optical basicity. The high third order nonlinear susceptibility χ⁽³⁾ = 2.0 × 10^− 12 esu at 800 nm was also obtained in the 36Bi₂O₃-18TeO₂-46B₂O₃ glass.     

Variation of optical basicity with probe ion,for Cs2O + B2O3 and Li2O + B2O3 glasses

Optical basicities (Γ) for Cs₂O + B₂O₃ and Li₂O + B₂O₃ glasses have been measured as a function of glass composition, using Tl⁺, Pb²⁺ and Bi³⁺ probe ions. The three probe ions register different values of Γ for glasses of given composition (and also for pure B₂O₃ glass and water). The divergence decreases as the alkali metal ion size decreases.For the Li₂O + B₂O₃ glasses, ideal (calculated) optical basicities agree within experimental precision with experimental values registered by Pb²⁺ (Γ_Pb²⁺) up to about 15 mol% Li₂O. For higher Li₂O contents, and for the Cs₂O + B₂O₃ glasses, ideal optical basicities agree less well with Γ_Pb²⁺, but show similar trends with composition to those shown by Γ_Pb²⁺.     

The effect of PbF2 content on the microstructure and upconversion luminescence of Er-doped SiO2-PbF2-PbO glass ceramics

The Er³⁺ doped transparent oxyfluoride glass ceramics were obtained by appropriate heat treatment of the precursor glasses with composition (mol%) 50SiO₂-xPbF₂-(50 − x)PbO-0.5ErF₃. The microstructure and optical properties of the glasses and glass ceramics were determined by differential scanning calorimetry (DSC), X-ray diffraction (XRD), absorption spectra and luminescence spectra. The intensity of upconversion luminescence significantly increased in glass ceramics compared to that in precursor glass. The emission bands centered around 660 nm (⁴F_9/2 → ⁴I_15/2) and 410 nm (²H_9/2 → ⁴I_15/2) were simultaneously observed in glass ceramics but cannot be seen in the corresponding precursor glass. The influence of different PbF₂ content on the microstructure and upconversion luminescence of the samples was analyzed in detail. The results indicated that with the increase of PbF₂ content, the Ω₂ was almost the same and the ratios of red to green upconversion luminescence decreased in glass ceramics.     

Glass preparation and temperature-induced crystallization in multicomponent B2O3-PbX2-PbO-Al2O3-WO3-Dy2O3 (X = F, Cl, Br) system

Multicomponent lead borate glasses modified by PbX₂ (X = F, Cl or Br) were examined. For the first time, lead tungstate PbWO₄ crystallites dispersed into glass matrices were successfully obtained from controlled crystallization. Excitation by 310 nm line leads to broad blue luminescence related to the radiative transition which occurred in the PbWO₄ crystallites. It was found that halogen X ions (X = F, Cl or Br) were also incorporated in the distorted crystal system of PbWO₄. It was proved by results obtained from X-ray diffraction as well as luminescence measurements.     

Electrical transport properties of 0.5Li2O-0.5M2O-2B2O3 (M = Li, Na and K) glasses

Transparent glasses in the system 0.5Li₂O-0.5M₂O-2B₂O₃ (M = Li, Na and K) were fabricated via the conventional melt quenching technique. The amorphous and glassy nature of the samples was confirmed via the X-ray powder diffraction and the differential scanning calorimetry, respectively. The frequency and temperature dependent characteristics of the dielectric relaxation and the electrical conductivity were investigated in the 100 Hz-10 MHz frequency range. The imaginary part of the electric modulus spectra was modeled using an approximate solution of Kohrausch-Williams-Watts relation. The stretching exponent, β, was found to be temperature independent for 0.5Li₂O-0.5Na₂O-2B₂O₃ (LNBO) glasses. The activation energy associated with DC conduction was found to be higher (1.25 eV) for 0.5Li₂O-0.5K₂O-2B₂O₃ (LKBO) glasses than that of the other glass systems under study. This is attributed to the mixed cation effect.