Spectroscopic properties of Er-doped xGeO2-(80 − x)TeO2-10ZnO-10BaO glasses

Erbium-doped glasses with composition xGeO₂-(80 − x)TeO₂-10ZnO-10BaO were prepared by melt-quenching technique. The phonon sideband spectra and the optical absorption band edges for the host matrix were confirmed by means of the spectral measurements. Standard Judd-Ofelt calculations have been completed to these glasses. The dependence of up-conversion and infrared emission under 980 nm excitation on the glass composition was studied. The quantum efficiencies for the ⁴I_13/2 → ⁴I_15/2 transition of trivalent erbium in the glasses were estimated.     

Studies of some mechanical and optical properties of: (70 − x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Specimens of the glassy system: (70 − x)TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by the melt-quenching. An ultrasonic pulse-echo technique was employed, at 5 MHz, for measuring: the ultrasonic attenuation, longitudinal and shear wave velocities, elastic moduli, Poisson ratio, Debye temperature and hardness of the present glasses. It is found that the gradual replacement of TeO₂ by Li₂O in the glass matrix up to 30 mol% leads to decrease the average crosslink density and rigidity of prepared samples which affects the properties, i.e., the hardness, ultrasonic wave velocities and elastic moduli are decreased, while the Poisson ratio and the ultrasonic attenuation are increased. Also, optical absorption spectra were recorded in the range, 200-800 nm for these glasses. The obtained results showed that a gradual shift in the fundamental absorption edge toward longer wavelengths occurred. Values of both of the optical energy gap, E_opt, and width tails, ΔE, are determined. It is observed that E_opt is decreased and ΔE increased with the increase of Li₂O in the glass matrix up to 30 mol%. The compositional dependences of the above properties are discussed and correlated to the structure of tested glasses.     

The glass transition temperature and infrared absorption spectra of: (70−x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Glasses of the system: (70−x) TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by melt quench technique. Dependencies of their glass transition temperatures (T_g) and infrared (IR) absorption spectra on composition were investigated. It is found that the gradual replacement of oxides, TeO₂ by Li₂O, decreases the glass transition temperature and increases the fragility of the glasses. Also, IR spectra revealed broad weak and strong absorption bands in the investigated range of wave numbers from 4000 to 400 cm⁻¹. These bands were assigned to their corresponding bond modes of vibration with relation to the glass structure.     

Spectrometric and ellipsometric studies of (1 − x)TiO2 · xLn2O3 (Ln = Nd, Sm, Gd, Er, Yb) thin films

Spectrometric and ellipsometric studies of (1 − x)TiO₂ · xLn₂O₃ (Ln = Nd, Sm, Gd, Er, Yb; x = 0.33, 0.5) thin films at room temperature were performed. The obtained dispersion dependences of refractive indices are successfully described by the optical-refractometric relation. The dependence of optical pseudogap and refractive indices on composition and molar mass of the films is investigated. The influence of compositional disordering on the energy width of the exponential absorption edge is studied.     

Effects of Nb2O5 Replacement by Er2O3 on elastic and structural properties of 75TeO2-(10 − x)Nb2O5-15ZnO-(x)Er2O3 glass

Tellurite 75TeO₂-(10 − x)Nb₂O₅-15ZnO-(x)Er₂O₃; (x = 0.0-2.5 mol%) glass system with concurrent reduction of Nb₂O₅ and Er₂O₃ addition have been prepared by melt-quenching method. Elastic properties together with structural properties of the glasses were investigated by measuring both longitudinal and shear velocities using the pulse-echo-overlap technique at 5 MHz and Fourier Transform Infrared (FTIR) spectroscopy, respectively. Shear velocity, shear modulus, Young's modulus and Debye temperature were observed to initially decrease at x = 0.5 mol% but remained constant between x = 1.0 mol% to x = 2.0 mol%, before increasing back with Er₂O₃ addition at x = 2.5 mol%. The initial drop in shear velocity and related elastic moduli observed at x = 0.5 mol% were suggested to be due to weakening of glass network rigidity as a result of increase in non-bridging oxygen (NBO) ions as a consequence of Nb₂O₅ reduction. The near constant values of shear velocity, elastic moduli, Debye temperature, hardness and Poisson's ratio between x = 0.5 mol% to x = 2.0 mol% were suggested to be due to competition between bridging oxygen (BO) and NBO ions in the glass network as Er₂O₃ gradually compensated for Nb₂O₅. Further addition of Er₂O₃ (x > 2.0 mol%) seems to further reduce NBO leading to improved rigidity of the glass network causing a large increase of ultrasonic velocity (v_L and v_S) and related elastic moduli at x = 2.5 mol%. FTIR analysis on NbO₆ octahedral, TeO₄ trigonal bipyramid (tbp) and TeO₃ trigonal pyramid (tp) absorption peaks confirmed the initial formation of NBO ions at x = 0.5 mol% followed by NBO/BO competition at x = 0.5-2.0 mol%. Appearance of ZnO₄ tetrahedra and increase in intensity of TeO₄ tbp absorption peaks at x = 2.0 mol% and x = 2.5 mol% indicate increase in formation of BO.     

Three-dimensional structure of fast ion conducting 0.5Li2S + 0.5[(1 − x)GeS2 + xGeO2] glasses from high-energy X-ray diffraction and reverse Monte Carlo simulations

A high-energy X-ray diffraction study has been carried out on a series of 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses with x = 0.0, 0.1, 0.2, 0.4, 0.6 and 0.8. Structure factors were measured to wave vectors as high as 30 Å⁻¹ resulting in atomic pair distribution functions with high real space resolution. The three dimensional atomic-scale structure of the glasses was modeled by reverse Monte Carlo simulations based on the diffraction data. Results from the simulations show that at the atomic-scale 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses may be viewed as an assembly of independent chains of (Li^+-S)₂GeS_2/2 and (Li^+-O)₂GeO_2/2 tetrahedra as repeat units, where the Li ions occupy the open space between the chains. The new structure data may help understand the reasons for the sharp maximum in the Li⁺ ion conductivity at x ∼ 0.2.     

Thermodynamical miscibility in 0.8[xB2O3-(1 − x)P2O5]-0.2K2O glasses

The thermodynamical miscibility in 0.8[xB₂O₃-(1 − x)P₂O₅]-0.2K₂O glasses has been studied by measuring the glass transition temperature and the mixing enthalpy. Measurements have been performed by differential scanning calorimeter and hydrofluoric acid solution calorimetry at 298 K. The enthalpies of mixing are significantly negative over the whole range of composition. The results are discussed in terms of intermolecular associations.     

Structure and properties of glasses in the MI + M2S + (0.1Ga2S3 + 0.9GeS2), M = Li, Na, K and Cs, system

The structure and properties of glasses in the MI + M₂S + (0.1Ga₂S₃ + 0.9GeS₂), M = Li, Na, K and Cs, system were studied using Raman, IR spectroscopy, DSC and density measurements to help better understand the ionic transport in these glasses. The glass forming ranges of these ternary glasses were compared to those of the binary alkali sulfide and germanium sulfide systems. The more extensive glass forming range in the Na₂S system was used to examine the more extensive changes of structure and properties of these glasses as a function of Na₂S content. As expected, non-bridging sulfurs (NBS) form with the addition of alkali sulfide. Unlike their oxide counterparts, however, the alkali sulfide doped glasses appear to support longer-range super-structural units. For example, evidence that the adamantine-like structure exists in the K₂S and Cs₂S modified glasses is found in the Raman spectra of the glasses. The structural role of the alkali iodide addition was also explored since the addition of alkali iodide helps to improve the conductivity. For most of these glasses, as observed in many other oxide glasses, the added MI dissolves interstitially into the glass structure network without changing the alkali sulfide network structure. In 0.6Na₂S + 0.4(0.1Ga₂S₃ + 0.9GeS₂) glasses, however, the added NaI may affect the glass structure as it causes systematic changes in the frequency of the Ge-S network mode as seen in the Raman spectra.     

The structure and optical properties of GeO2-GeS2 glasses

Oxy-chalcogenide glasses with compositions of xGeO₂-(100 − x)GeS₂, where 0 ? x ? 100 mol%, have been prepared and studied in terms of their structures and optical properties. X-ray fluorescence spectroscopy shows that Ge:S ratio can deviate from GeS₂ by ∼10 at.%, depending critically upon the preparation conditions. Raman scattering spectroscopy suggests that stoichiometric GeO₂-GeS₂ glasses have a heterogeneous structure in the scale of 1-100 nm. The optical gaps are nearly constant at 3.0-3.5 eV for glasses with 0 ? x ? 80 mol% and abruptly increase to ∼6 eV in GeO₂. This dependence suggests that the optical gap is governed by GeS₂ clusters, which are isolated and/or percolated. Composition-deviated glasses appear as orange and brown, and these glasses seem to have more inhomogeneous structures.     

Spectroscopic and magnetic behavior of xNd2O3(1−x)(3Bi2O3 · PbO) glasses

Glasses of the xNd₂O₃(1−x)(3Bi₂O₃ · PbO) system with 0?x?0.30 were obtained and studied by IR spectroscopy, X-ray photoelectron spectroscopy (XPS), density and magnetic susceptibility measurements. IR and density measurements show that the addition of neodymium ions produces structural changes and the neodymium ions play a network modifier role in the host glass matrix. XPS investigation permitted following the evolution of the structural disorder, of the degree of polymerization of bismuthate chains and of the fraction of bridging oxygens with respect to the neodymium ion concentration of the studied glasses. Magnetic susceptibility data show that the Nd³⁺ ions are present as isolated species for x?0.05 and as both isolated and exchange coupled species for higher x values.     

Sodium tracer diffusion in glasses of the type (CaO·Al2O3)x(2 SiO2)1−x

Tracer diffusion coefficients of the radioactive isotope Na-22 were measured in glasses of the type (CaO·Al₂O₃)_x(2 SiO₂)_1−x to study the diffusion of sodium as a function of glass composition, x, temperature and initial water content. The diffusion of Na-22 in glasses diffusion-annealed in dry air can always be well described by a single tracer diffusion coefficient, but sometimes not in samples annealed in common air. It was found that the sodium tracer diffusion coefficient decreases by about six orders of magnitude when the glass composition x changes from 0 to 0.75 at 800 °C. The temperature dependence of the diffusion of sodium seems to decrease as the silica content increases. Variations of the initial water content in some of the glasses investigated did not very significantly influence the rate of the tracer diffusion of sodium.     

Temperature-assisted electrical poling of TeO2-Bi2O3-ZnO glasses for non-linear optical applications

The suitability for effective thermal poling of the ternary tellurite glasses with the compositions (100 − 2x)TeO₂-xBi₂O₃-xZnO (x = 5, 10 and 15, in molar percentage) for the second harmonic generation (SHG) was analyzed. The glass transitions and crystallization temperatures were studied via differential thermal analysis. The structural properties of the annealed glasses and furtherly heat-treated samples were probed by extended X-ray absorption fine structure (EXAFS) spectroscopy. Thermal poling of the glasses was undertaken conventionally at various temperatures close to the glass transition temperature under high vacuum and the second harmonic generated signals were compared. A new technique of two stage poling was tested for comparison. The non-linear second harmonic signal of the poled glasses was analyzed using the Maker-fringe technique and it was found that the two stage poling enhanced the non-linear efficiency when compared to the conventionally poled samples.     

Transport property and structural characterization studies on (1 − x)[0.75AgI:0.25AgCl]:xTiO2 conducting composite electrolyte system

Transport property and structural investigation have been carried out on newly synthesized Ag⁺ ion conducting composite electrolyte system. The composite electrolyte system (1 − x)[0.75AgI:0.25AgCl]:xTiO₂, where 0 ? x ? 0.5 (in molar weight fraction) has been synthesized by melt quenching and annealing methods. The chemical compound TiO₂ (second phase dispersoid) dispersed in different compositions in a quenched (0.75AgI:0.25AgCl) mixed system/solid solution; this solid solution was used as a first phase host salt in place of AgI. The different preparation routes were adopted for the composite electrolyte system. Composition x = 0.1 exhibited highest conductivity at room temperature. The composite system 0.9[0.75AgI:0.25AgCl]:0.1TiO₂ was synthesized at different soaking times by melt quenching method. The system exhibited optimum conductivity at 20 min soaking time (σ_rt ≈ 1.4 × 10⁻³ S/cm). The ac conductivity has been measured from Z′-Z″ (Cole-Cole) complex impedance plots using impedance spectroscopic (IS) technique. The electrical conductivity as a function of temperature and frequency has been studied, and activation energy E_a, was calculated from Arrhenius plots for all compositions (0 ? x ? 0.5). The dc conductivity value has been evaluated from Log σ vs. log f plots. Structural characterization studies were carried out by X-ray diffraction (XRD) and differential thermal analysis (DSC) techniques.     

Structure of partially reduced xPbO (1 − x)SiO2 glasses: combined EXAFS and MD study

We have studied the structure of partially reduced lead-silicate glasses using combined EXAFS (extended X-ray absorption fine structure) and MD (molecular dynamics) methods. The analysis was performed for glasses of x[(1 − p)Pb pPbO] (1 − x)SiO₂ composition, x = 0.3, 0.5, 0.7, where parameter (1 − p) describes the degree of reduction, i.e. the content of the granular metallic phase, appearing as the result of the reduction process (e.g. annealing in hydrogen atmosphere). In the EXAFS experiment (1 − p) was expressed via the time of reduction realized at 400 °C (1.5 h, 24 h, 70 h), whereas in the MD simulations it was determined precisely by using proper numbers of particles (corresponding to (1 − p) = 0.0, 0.25, 0.5, 0.75 and 1.0). In the paper we describe in detail the local structure around lead atoms and its changes in the function of glass composition and reduction degree. The tendency for agglomeration of Pb⁰ into clusters, the formation of the granular metallic phase, and continuity of silica and lead oxide subnetworks are discussed. A good agreement between EXAFS-extractcd and MD-extracted parameters of the short-range structure encouraged us to preform a medium-range order analysis, based on the MD simulations only. Moreover, combining the EXAFS and MD methods we could correlate the reduction time (technological parameter) with the degree of reduction (1 − p) and the actual state of the granular structure. The latter relation may be useful for controlled production of reduced glasses of pre-requcstcd physical properties.     

The effect of PbF2 content on the microstructure and upconversion luminescence of Er-doped SiO2-PbF2-PbO glass ceramics

The Er³⁺ doped transparent oxyfluoride glass ceramics were obtained by appropriate heat treatment of the precursor glasses with composition (mol%) 50SiO₂-xPbF₂-(50 − x)PbO-0.5ErF₃. The microstructure and optical properties of the glasses and glass ceramics were determined by differential scanning calorimetry (DSC), X-ray diffraction (XRD), absorption spectra and luminescence spectra. The intensity of upconversion luminescence significantly increased in glass ceramics compared to that in precursor glass. The emission bands centered around 660 nm (⁴F_9/2 → ⁴I_15/2) and 410 nm (²H_9/2 → ⁴I_15/2) were simultaneously observed in glass ceramics but cannot be seen in the corresponding precursor glass. The influence of different PbF₂ content on the microstructure and upconversion luminescence of the samples was analyzed in detail. The results indicated that with the increase of PbF₂ content, the Ω₂ was almost the same and the ratios of red to green upconversion luminescence decreased in glass ceramics.     

Vibrational, EPR and optical spectroscopy of the Cu doped glasses with (90-x)TeO2-10GeO2-xWO3 (7.5 ≤ x ≤ 30) composition

Infrared, EPR and optical absorption studies on (90-x)TeO₂-10GeO₂-xWO₃ (7.5 ≤ x ≤ 30) glasses containing Cu²⁺ spin probe have been carried out. The Infrared spectral studies show that the structure of glass network consists of [TeO₄], [TeO₃]/[TeO_3 + 1], [WO₄], [WO₆] and [GeO₆] units in the disordered manner. Physical parameters such as density (ρ), molar volume (V_m), oxygen packing density (OPD), oxygen molar volume (V_o), optical basicity (Λ), oxide ion polarizability (α_O²⁻), inter ionic distances and the concentration of ions per unit volume of Te, Ge, W, Cu and O have been determined. The spin-Hamiltonian parameters (g_||, g_⊥ and A_||) of Cu²⁺ ions in the present glasses have been estimated from EPR spectra at 300 K. Bonding parameters such as α², β₁², β², Γ_σ, and Γ_π have been calculated from both optical absorption and EPR data. The observed variations in spin-Hamiltonian parameters and bonding parameters have been correlated to the structural modifications due to the WO₃ incorporation into the TeO₂ glass network at constant 10 mol% GeO₂ content.     

Preparation and characterization of glasses in the Ag2S + B2S3 + GeS2 system

The glass forming range of the Ag₂S + B₂S₃ + GeS₂ ternary system was investigated for the first time and a wide range of ternary glasses were obtained. The Archimedes’ method was used to determine the densities of the Ag-B-Ge glasses. The thermal properties of these thioborogermanate glasses were studied by DSC and TMA. The Raman, IR and NMR spectroscopy were used to explore the short-range order structure of the binary (Ag-B) and (Ag-Ge) and ternary (Ag-B-Ge) glasses. The results show the presence of bridging sulfur tetrahedral units, GeS_4/2 and AgBS_4/2, and trigonal units, BS_3/2, in the ternary glasses. Non-bridging sulfur units, AgSGeS_3/2 and Ag₃B₃S₃S_3/2 six membered rings, are also observed in these glasses at higher Ag₂S modification levels because the further addition of Ag₂S results in the degradation of the bridging structures to form non-bridging structures. The NMR studies show that Ag₂S goes into the GeS₂ subnetwork to form Ag₃S₃GeS_1/2 groups before going to the B₂S₃ subnetwork. In doing so, it is suggested that B₁₀S₂₀ supertetrahedra exist in Ag₂S + B₂S₃ and Ag₂S + B₂S₃ + GeS₂ glasses. Significantly B-S-Ge bonds form in the B₂S₃ + GeS₂ glasses, whereas they appear to be absent in the ternary glasses. From these observations, a structural model for these glasses has been developed and proposed.     

The comparative structure, properties, and ionic conductivity of LiI + Li2S + GeS2 glasses doped with Ga2S3 and La2S3

The well known and characterized fast ion conducting (FIC) LiI + Li₂S + GeS₂ glass-forming system has been further optimized for higher ionic conductivity and improved thermal and chemical stability required for next generation solid electrolyte applications by doping with Ga₂S₃ and La₂S₃. These trivalent dopants are expected to eliminate terminal and non-bridging sulfur (NBS) anions thereby increasing the network connectivity while at the same time increasing the Li⁺ ion conductivity by creating lower basicity [(Ga or La)S_4/2]⁻ anion sites. Consistent with the finding that the glass-forming range for the Ga₂S₃ doped compositions is larger than that for the La₂S₃ compositions, the addition of Ga₂S₃ is found to eliminate NBS units to create bridging sulfur (BS) units that not only gives an improvement to the thermal stability, but also maintains and in some cases increases the ionic conductivity. The compositions with the highest Ga₂S₃ content showed the highest T_gs of ∼325 °C. The addition of La₂S₃ to the base glasses, by comparison, is found to create NBS by forming high coordination octahedral LaS₆³⁻ sites, but yet still improved the chemical stability of the glass in dry air and retained its high ionic conductivity and thermal stability. Significantly, at comparable concentrations of Li₂S and Ga₂S₃ or La₂S₃, the La₂S₃-doped glasses showed the higher conductivities. The addition of the LiI to the glass compositions not only improved the glass-forming ability of the compositions, but also increased the ionic conductivity glasses. LiI concentrations from 0 to 40 mol% improved the conductivities of the Ga₂S₃ glasses from ∼10⁻⁵ to ∼10⁻³ (Ω cm)⁻¹ and of the La₂S₃ glasses from ∼10⁻⁴ to ∼10⁻³ (Ω cm)⁻¹ at room temperature. A maximum conductivity of ∼10⁻³ (Ω cm)⁻¹ at room temperature was observed for all of the glasses and this value is comparable to some of the best Li ion conductors in a sulfide glass system. Yet these new compositions are markedly more thermally and chemically stable than most Li⁺ ion conducting sulfide glasses. LiI additions decreased the T_gs and T_cs of the glasses, but increased the stability towards crystallization (T_c − T_g).     

Dielectric analysis of tungsten-phosphoniobate 20A2O-30WO3 -10Nb2O5 -40P2O5 (A = Li, Na) glass-ceramics

New phosphate glasses of the quaternary system A₂O-Nb₂O₅-WO₃-P₂O₅, where X = Li and Na were prepared by the melt-quenching method. The introduction of WO₃ in the glass composition was based on the proposal of analysing the effect of the diminishing of the molar amount of the alkaline oxide and thus decreasing the molar ratio between network modifiers and network formers (M/F).In the present work we present the preparation of 20A₂O-30WO₃-10Nb₂O₅-40P₂O₅ (A = Li, Na) transparent glasses. These glasses were heat-treated in air, at 550 °C and 650 °C for 4 h. The structure of the obtained samples was studied by X-ray powder diffraction (XRD) and Raman spectroscopy and the morphology by scanning electron microscopy (SEM). The dc (σ_dc), ac (σ_ac) conductivity and dielectric spectroscopy measurements were performed in the function of the temperature and were related with the structural changes of the glass structures.     

Thermal and some physical properties of glasses in the La2O3−CaO−B2O3 ternary system

Glasses in the La₂O₃−CaO−B₂O₃ ternary system were studied. The glass forming range as determined by the appearance of the annealed cast was found to match previously published findings. Clear glasses were formed in the composition range of 5.7−19.1 mol% La₂O₃ with constant B₂O₃ content of 71.4 mol%, and in glasses of constant La₂O₃:CaO ratio of 1:4 with B₂O₃ content in the range of 71.4-55.0 mol%. The non-linear optical crystalline phase La₂Ca₂B₁₀O₁₉ was crystallized from the clear glasses after heat treatments, as determined by powder XRD. Two types of the LaBO₃ crystalline phases were detected in the partially and the fully crystallized glass compositions outside the glass forming range. Data are reported for the glass transition temperature (T_g), dilatometric softening point (T_d), linear coefficient of expansion (α), onset crystallization temperature (T_x), exothermal peak temperature (T_P), density (ρ) and index of refraction (n_D) in the clear glasses.