Energy transfer up-conversion in Tm-doped silica fiber

A study of the mechanisms responsible for the infra-red to near infra-red up-conversion in Tm³⁺-doped silica fibers is presented. Up-conversion luminescence was observed from the ³H₄ level of Tm³⁺ under 1586 nm pumping into the ³F₄ level. The quadratic dependence of the up-conversion luminescence at 800 nm on the 1800 nm luminescence from the ³F₄ level confirms that the ³H₄ level is populated by a two photon process. Two possible processes are proposed as mechanisms responsible for the up-conversion: excited state absorption and energy transfer up-conversion. The decay characteristics of the luminescence from the ³H₄ level were studied under direct and indirect pumping at 786 and 1586 nm, respectively. By comparing the decay waveforms to the solution of a simple set of rate equations, the energy transfer up-conversion process (³F₄, ³F₄ → ³H₄, ³H₆) was established at Tm₂O₃ concentrations greater than 200 ppm.     

Concentration quenching of fluorescence from the (P0 + P1) manifold in heavily-doped Pr: ZBAN glasses

Fluorescence waveforms from the (³P₀ + ³P₁) manifold in Pr³⁺ doped ZBAN glass at wavelengths of 520, 635 and 695 nm were measured for Pr³⁺ concentrations from 4 to 12 mol%. The waveforms were found to be non-exponential with decay rates rapidly increasing with Pr³⁺ concentration and independent of whether the ³P₀ or the ³P₁ level was excited. The multipolar energy transfer model was used to analyse the waveforms and this showed that concentration quenching was due to cross-relaxation by dipole-dipole interaction. The critical concentration, at which the cross-relaxation rate equals the intrinsic decay rate, was found to be of 2.06 × 10²⁶ m⁻³ (1.20 mol%). There was no evidence of excitation diffusion for Pr³⁺ concentrations of up to 12 mol%.     

Dependence of fluorescence properties on substitution of BaF2 for BaO in barium gallo-germanate glass

3.5 mol%, 6.5 mol%, 9.5 mol%, and 12.5 mol% BaF₂ were gradually substituted for BaO in 0.3 mol% Tm₂O₃ doped 12.5 BaO-12.5 Ga₂O₃-75 GeO₂ (BGG) glasses to study the effect of the substitution on the OH⁻ elimination and emission properties. The FTIR spectral demonstrated that the substitution effectively eliminated OH⁻ groups and 9.5 mol% BaF₂ was enough for the OH⁻ elimination. The J-O parameters of all the samples were calculated according to J-O theory. The calculation showed that the Ω₂ parameter decreased monotonically with BaF₂ content increasing, while Ω₄ and Ω₆ did not change much. The radiative lifetime increased while BaF₂ content increased as well. The emission cross section of ³F₄ → ³H₆ transition was calculated by the F-L formula. However, it decreased with the gradual BaF₂ addition.

Research Highlights

? OH⁻ groups were eliminated by the substitution of BaF₂ for BaO in (BGG) glass. ? The optimal substitution level of BaF₂ was 9.5 mol% for OH⁻ elimination. ? The Ω₂ parameter decreased monotonically by the elimination. ? The emission cross section of ³F₄ → ³H₆ transition was decreased by the substitution.     

Energy transfer between Tm and Er ions in a TeO2-based glass pumped at diode laser wavelength

In this paper we investigate the energy transfer processes in Tm³⁺/Er³⁺ doped telluride glass pumped at the commercial diode laser pump wavelength ∼800 nm. Tailoring the rare-earths content in the glass matrix, seven main energy transfer channels within the doping range considered were identified. A 6-fold enhancement of the Er³⁺ visible frequency upconversion fluorescence at ∼660 nm is observed due to the inclusion of Tm³⁺ ions. This is evidence of the relevant contribution of the route Er₁(⁴I_11/2) + Er₂(⁴I_13/2) → Er₁(⁴I_15/2) + Er₂(⁴F_9/2) to the process. Energy migration among pumped ⁴I_9/2 level reducing the efficiency of the upconversion emission rate (³H_11/2, ⁴S_3/2, and ⁴F_9/2) is observed for Er³⁺ above 1.5 wt%. The rate equations regarding the observed energy transfer routes are determined and a qualitative analysis of the observed processes is reported.     

Improvement of the Tm:H4 level lifetime in silica optical fibers by lowering the local phonon energy

The role of some glass network modifiers on the quantum efficiency of the near-infrared fluorescence from the ³H₄ level of Tm³⁺ ion in silica-based doped fibers is studied. Modifications of the core composition affect the spectroscopic properties of Tm³⁺ ion. Adding 17.4 mol% of AlO_3/2 to the core glass caused an increase of the ³H₄ level lifetime up to 50 μs, 3.6 times higher than in pure silica glass. The quantum efficiency was increased from 2% to approximately 8%. On the opposite, 8 mol% of PO_5/2 in the core glass made the lifetime decrease down to 9 μs. These changes of Tm³⁺ optical properties are assigned to the change of the local phonon energy to which they are submitted by modifiers located in the vicinity of the doping sites. Some qualitative predictions of the maximum achievable quantum efficiency are possible using a simple microscopic model to calculate the non-radiative de-excitation rates.     

Optical properties of and concentration quenching in Bi2O3-B2O3-Ga2O3 glasses

Er₂O₃-doped Bi₂O₃-B₂O₃-Ga₂O₃ glasses were prepared by the conventional melt-quenching method, and the Er³⁺:⁴I_13/2 → ⁴I_15/2 fluorescence properties are studied for different Er³⁺ concentrations. when the Er₂O₃ concentration increases from 0.03 to 3.0 mol%, the measured lifetime of Er³⁺:⁴I_13/2 level decrease from 2.24 to 0.9 m s, and from 0.25 to 0.20 m s for the Er³⁺:⁴I_11/2 level. The fast energy migration among Er³⁺ ions cause the reduction of lifetime of the ⁴I_13/2 level, whereas the change in the ⁴I_11/2 level is mainly due to a cooperative upconversion process (⁴I_11/2, ⁴I_11/2) → (⁴F_7/2, ⁴I_15/2). Based on the dipole-dipole interaction theory, the interaction parameter, C_Er,Er, for the migration rate of Er³⁺:⁴I_13/2 ↔ ⁴I_13/2 was calculated to be 32 × 10⁻⁴⁰ cm⁶ s⁻¹.     

The effect of PbF2 content on the microstructure and upconversion luminescence of Er-doped SiO2-PbF2-PbO glass ceramics

The Er³⁺ doped transparent oxyfluoride glass ceramics were obtained by appropriate heat treatment of the precursor glasses with composition (mol%) 50SiO₂-xPbF₂-(50 − x)PbO-0.5ErF₃. The microstructure and optical properties of the glasses and glass ceramics were determined by differential scanning calorimetry (DSC), X-ray diffraction (XRD), absorption spectra and luminescence spectra. The intensity of upconversion luminescence significantly increased in glass ceramics compared to that in precursor glass. The emission bands centered around 660 nm (⁴F_9/2 → ⁴I_15/2) and 410 nm (²H_9/2 → ⁴I_15/2) were simultaneously observed in glass ceramics but cannot be seen in the corresponding precursor glass. The influence of different PbF₂ content on the microstructure and upconversion luminescence of the samples was analyzed in detail. The results indicated that with the increase of PbF₂ content, the Ω₂ was almost the same and the ratios of red to green upconversion luminescence decreased in glass ceramics.     

Composition dependent upconversion of Er-doped PbF2-TeO2 glasses

The upconversion properties of Er³⁺ ions were studied for heavy metal oxyfluoride tellurite glass hosts xPbF₂-(100−x)TeO₂ under 975 nm excitation. The intense green (529 and 545 nm) and relative weak red (657 nm) emissions corresponding to the transitions ⁴S_3/2 → ⁴I_15/2, ²H_11/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2, respectively, were simultaneously observed at room temperature. The PbF₂ content has an important influence on upconversion luminescence emission. With increasing PbF₂ content, the intensities of green (529 nm) and red (657 nm) emissions increase slightly, while the green (545 nm) emission increases significantly. These results indicate that PbF₂ has more influence on the green (545 nm) emission than the green (529 nm) and red (657 nm) emissions. The intense green emission observed suggest that Er³⁺-doped heavy metal oxyfluoride tellurite glasses can become candidates for developing upconversion optical devices.     

1.48 μm emission properties and the cross-relaxation mechanism in chalcohalide glass doped with Tm

1.48 μm emission properties and the cross-relaxation mechanism of Tm³⁺ ions in 0.7(Ge_0.25As_0.10S_0.65) + 0.15GaS_3/2 + 0.15CsBr glass were investigated. Both the relative intensity ratio of the 1.48 μm emission to 1.82 μm and the measured lifetime of the ³H₄ level decreased with increasing Tm³⁺ concentration. When temperature decreased from room temperature to 20 K, lifetimes of the ³H₄ level increased from 670 to 970 μs. At the same time, the critical distance for cross-relaxation decreased from 1.11 to 0.93 nm. These results indicate that cross-relaxation (³H₄, ³H₆ → ³F₄, ³F₄) became less effective as temperature decreased. Analysis of the temperature dependence of cross-relaxation rates showed that cross-relaxation in Tm³⁺ is a phonon-assisted energy transfer process. The major phonon contributing to the process is from the Ga-Br vibration in [GaS_3/2Br]⁻ units.     

Growth, refined structural and spectroscopic characteristics of Tm-doped NaGd(WO4)2 single crystals

The details of Tm³⁺-doped NaGd(WO₄)₂ single-crystal growth are discussed, the results of precise investigations of its structural and spectroscopic characteristics, as well as the analysis of cross-relaxation process of Tm³⁺ ions (³H₄→³F₄, ³H₆→³F₄) in this crystal are presented. Based on the Judd–Ofelt theory, three intensity parameters, spontaneous emission probabilities, fluorescence branching ratios and fluorescence quantum efficiency from ³H₄ and ³F₄ levels were refined.     

Effect of Bi2O3 proportion on physical, structural and electrical properties of zinc bismuth phosphate glasses

The variation in physical, structural and electrical properties has been studied as a function of Bi₂O₃ content in 20ZnF₂-(10 + x) Bi₂O₃-(70-x) P₂O₅, 0 ≤ x ≤ 10 mol% glasses, which were prepared by melt quenching technique and characterized by differential thermal analysis (DTA). Colorless samples, which have no absorption peaks, are obtained for 10 and 12 mol% of Bi₂O₃ and the glasses are slowly becoming brownish from 15 to 20 mol% of Bi₂O₃ which exhibit two absorption peaks at ~ 370 nm, ~ 450 nm correspond to Bi° transitions ⁴S_3/2 → ²P_3/2 and ⁴S_3/2 → ²P_1/2 respectively. The decrease in ³P₁ → ¹S₀ transition of Bi³⁺ photo luminescence emission for 18 and 20 mol% of Bi₂O₃ and increase in optical absorption area shows the reduction of Bi³⁺ to Bi°. From FTIR studies it is observed that an addition of Bi₂O₃ decreases the P―O―P covalent bond by forming P―O―Bi bonds due to high polarizing nature of Bi³⁺ ions. Dielectric parameters like ε', tan δ and a.c. conductivity σ_ac are found to increase and activation energy for a.c. conduction is found to decrease with the increase in the concentration of Bi₂O₃. Density of defect energy states is found to increase for higher concentration of Bi₂O₃ and is discussed according to quantum mechanical tunneling (QMT) model.     

Float zone growth of Dy:GdVO4 single crystals for potential use in solid-state yellow lasers

Single crystals of dysprosium-doped gadolinium orthovanadate (Dy:GdVO₄) were successfully grown by the floating zone method and their fluorescence properties were investigated. The as-grown crystals did not contain any macroscopic defects such as cracks and inclusions for any Dy-concentration of up to 4 at%. Every crystal showed optical homogeneity under observation with a polarizing microscope; that is, no low-angle grain boundaries and growth striations were detected. In the visible region, two distinct fluorescence bands were observed around 480 and 575 nm, corresponding to ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 transitions, respectively. The excitation spectrum for the emission of 573 nm indicates the possibility to use a commercially available laser diode of 450 nm as a pumping source for solid-state yellow laser.     

Variation of luminescence properties of Na2O-CaO-SiO2: Nd glass with crystallinity

The optical absorption and emission intensities of Nd³⁺-doped transparent glass-ceramics with high crystallinity in Na₂O-CaO-SiO₂ (NSC) system were studied. The transmittance of NCS decreases with increasing degree of crystallinity, however it still remains 65.5% at λ = 710 nm when the crystallization is almost completed. Judd-Ofelt theory is performed to evaluate the radiative transition probability as well as quality factor, branching ratio and emission cross section. The maximum values of Ω₂ and emission cross section (⁴F_3/2 → ⁴I_11/2) of NCS are obtained after nucleating at 630 °C for 10 h. The quality factor increases with increasing crystallinity, while branching ratio for ⁴F_3/2 → ⁴I_11/2 is opposite. The results show that transparent glass-ceramic with high crystallinity is a potential laser host for 1.06 μm emission.     

Crystal growth and spectroscopic properties of erbium doped Lu2SiO5

A high optical quality erbium doped Lu₂SiO₅ single crystal has been grown by the Czochralski method. The distribution coefficient of Er³⁺ was measured to be ∼0.926. The absorption and emission spectra as well as the fluorescence decay curve of the excited state ⁴I_13/2 were measured at room temperature. The spectroscopic parameters were calculated using the Judd–Ofelt theory, and the J–O parameters Ω₂, Ω₄ and Ω₆ were found to be 4.451×10^-20, 1.614×10^-20 and 1.158×10^-20 cm², respectively. The room-temperature fluorescence lifetime of the Er³⁺⁴I_13/2→⁴I_15/2 transition was measured to be 7.74 ms. The absorption and emission cross-section as well as the gain cross-section in the eye-safe regime of 1400–1700 nm were also determined and discussed.     

Investigation of infrared emission and lifetime in Tm-doped 75TeO2:20ZnO:5Na2O (mol%) glasses: Effect of Ho and Yb co-doping

In this paper we describe fabrication and characterization of rare-earth-doped active tellurite glasses to be used as active laser media for fiber lasers emitting in the 2 μm region. The base composition is (mol%): 75TeO₂-20ZnO-5Na₂O with different concentrations of Tm³⁺, Yb³⁺ and Ho³⁺ as dopants or co-dopants. Optical properties of doped glasses were studied and pumping at 800 nm and at 980 nm were tested in order to compare the efficiency of two pumping mechanisms. Optical characterization carried out on glasses containing only Tm³⁺ ions indicated the optimum concentration of Tm₂O₃ in terms of emission efficiency as 1 wt%. The addition of 5 wt% of Yb₂O₃ to Tm³⁺-doped glasses led to the best results in terms of intensity of fluorescence emission and of lifetime values. Yb and Ho co-doped Tm-tellurite glass was measured in emission.     

Structure and electrical conductivity of new Li2O-CeO2-B2O3 glasses

Fourier transformation infrared spectra, density and DC electrical conductivity of 30Li₂O · xCeO₂⋅(70 − x)B₂O₃ glasses, where x ranged between 0 and 15 mol%, have been investigated. The results suggested that CeO₂ plays the role of network modifier up to 7.5 mol%. At higher concentrations it plays a dual role; where most of ceria plays the role of network former. The density was observed to increase with increasing CeO₂ content. The effect on density of the oxides in the glasses investigated is in the succession: B₂O₃ < Li₂O < CeO₂. Most of CeO₂ content was found to be associated with B₂O₃ network to convert BO₃ into B O₄⁻ units. The contribution of Li⁺ ions in the conduction process is much more than that due to small polarons. The conductivity of the glasses is mostly controlled by the Li⁺ ions concentration rather than the activation energy for CeO₂ > 5 mol%. Lower than 5 mol% CeO₂ the conductivity is controlled by both factors. The dependence of W on BO₄⁻ content supports the idea of ionic conduction in these glasses.     

Cs2LiGdCl6 (Ce): New scintillation material

We investigated the scintillation properties of Cs₂LiGdCl₆:Ce³⁺ as a function of the Ce concentration. X-ray excited luminescence spectra of the scintillation material showed broad emission bands between 360 and 460 nm, with two overlapping peaks, due to the d→f transitions on Ce³⁺ ions. The samples provide good scintillation results. The energy resolution was found to be 5.0% (FWHM) at 662 keV for 10% Ce sample. Under γ-ray excitation, Cs₂LiGdCl₆:Ce³⁺ showed three exponential decay time components of about 130–200 ns decay time constant. The light output of the investigated samples was 20,000 photons/MeV for a 10% Ce concentration. The light output deviation from the linear response is within 7% between the energy range of 31 and 1333 keV. Overall, the scintillation properties confirm that Cs₂LiGdCl₆:Ce³⁺ single crystal is a promising candidate for medical imaging and radiation detection.     

Effects of Nb2O5 Replacement by Er2O3 on elastic and structural properties of 75TeO2-(10 − x)Nb2O5-15ZnO-(x)Er2O3 glass

Tellurite 75TeO₂-(10 − x)Nb₂O₅-15ZnO-(x)Er₂O₃; (x = 0.0-2.5 mol%) glass system with concurrent reduction of Nb₂O₅ and Er₂O₃ addition have been prepared by melt-quenching method. Elastic properties together with structural properties of the glasses were investigated by measuring both longitudinal and shear velocities using the pulse-echo-overlap technique at 5 MHz and Fourier Transform Infrared (FTIR) spectroscopy, respectively. Shear velocity, shear modulus, Young's modulus and Debye temperature were observed to initially decrease at x = 0.5 mol% but remained constant between x = 1.0 mol% to x = 2.0 mol%, before increasing back with Er₂O₃ addition at x = 2.5 mol%. The initial drop in shear velocity and related elastic moduli observed at x = 0.5 mol% were suggested to be due to weakening of glass network rigidity as a result of increase in non-bridging oxygen (NBO) ions as a consequence of Nb₂O₅ reduction. The near constant values of shear velocity, elastic moduli, Debye temperature, hardness and Poisson's ratio between x = 0.5 mol% to x = 2.0 mol% were suggested to be due to competition between bridging oxygen (BO) and NBO ions in the glass network as Er₂O₃ gradually compensated for Nb₂O₅. Further addition of Er₂O₃ (x > 2.0 mol%) seems to further reduce NBO leading to improved rigidity of the glass network causing a large increase of ultrasonic velocity (v_L and v_S) and related elastic moduli at x = 2.5 mol%. FTIR analysis on NbO₆ octahedral, TeO₄ trigonal bipyramid (tbp) and TeO₃ trigonal pyramid (tp) absorption peaks confirmed the initial formation of NBO ions at x = 0.5 mol% followed by NBO/BO competition at x = 0.5-2.0 mol%. Appearance of ZnO₄ tetrahedra and increase in intensity of TeO₄ tbp absorption peaks at x = 2.0 mol% and x = 2.5 mol% indicate increase in formation of BO.     

Crystallization behavior and microstructure of powdered and bulk ZnO-Al2O3-SiO2 glass-ceramics

The crystallization behavior of glass with the composition: 55.6 mol% SiO₂, 22.8 mol% Al₂O₃, 17.7 mol% ZnO and 3.84 mol% of TiO₂ as nucleating agent and with different particle sizes has been studied by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and tranmission electron microscopy (TEM). In glass powders two crystalline phases: zinc-aluminosilicate s.s. with high-quartz structure, Zn_x/2Al_xSi_3−xO₆, (x varies dependent on heat-treatment temperature) and gahnite are formed. The ratio of these phases depends on particle sizes. In bulk glass, however, gahnite is the sole crystalline phase. The composition of initially formed zinc-aluminosilicate s.s. was determined by Rietveld refinement of XRD patterns to be Zn_0.69Al_1.38Si_1.62O₆. With temperature increase, the amount of zinc-aluminosilicate s.s decreased with simultaneous reduce of zinc and aluminum incorporated in the structure. Eventually at 1423 K almost pure high-quartz structure was formed. The activation energies of zinc-aluminosilicate s.s. and gahnite crystallization were determined by non-isothermal method to be 510 ± 18 and 344 ± 17 kJ mol⁻¹, respectively. The latter value matches well with those cited in literature for crystal growth of gahnite in similar glasses. That is attributed to the fact that the high-quartz structure acts as a precursor for gahnite crystallization.     

Physical properties of lead iron phosphate glasses containing Cr2O3

The influence of Cr₂O₃ on glass forming characteristics and physical properties of PbO-Fe₂O₃-P₂O₅ glasses has been investigated by Raman and Mössbauer spectroscopies, X-ray diffraction analysis (XRD), Differential Thermal Analysis (DTA), Scanning Electron Microscopy (SEM) and impedance spectroscopy. Glasses of the general composition xCr₂O₃-(28.3-x)PbO-28.7Fe₂O₃-43.0P₂O₅, 0 ≤ × ≤ 10, (mol%) were prepared by conventional melt-quenching technique. The compositions containing up to 4 mol% Cr₂O₃ formed fully amorphous samples and their Raman spectra show systematic increase in the fraction of orthophosphate Q⁰ units with increasing Cr₂O₃ content and O/P ratio.On the other hand, compositions containing 8 and 10 mol% Cr₂O₃ partially crystallized during cooling and annealing to Fe₇(PO₄)₆, Fe₂Pb₃(PO₄)₄ and Cr₂Pb₃(PO₄)₄. A high tendency for crystallization of these melts is related to the high O/P (> 4) and Fe²⁺/Fe_tot (≈ 0.60) ratios.Electrical conductivity of xCr₂O₃-(28.3-x)PbO-28.7Fe₂O₃-43.0P₂O₅, 0 ≤ × ≤ 10, (mol%) compositions is independent of Cr₂O₃ and controlled entirely by the polaron transfer between Fe²⁺ and Fe³⁺ ions.