Effects of CaO on crystallization properties in BaO-SrO-TiO2-SiO2 glass-ceramics

The role of calcium oxide (CaO) was investigated in the crystallization of BaO-SrO-TiO₂-SiO₂ glass. The CaO dopant altered the oriented growth facets of crystal unit cells in the glass-ceramics. The crystallites are acicular in micron scale in the samples having as small as 1% CaO dopant, but are long granular in the nanometer scale in the sample without CaO. The glass-ceramics which have nano crystallites are observed with a less crystallization density qualitatively, a higher transmissivity in the wavelength range of 200-2600 nm, and 30% lower piezoelectric coefficient, d₃₃, at 9.5 ± 0.3 pC/N than those glass-ceramics having CaO in the study.     

Thermo-optic properties of B2O3 doped Li2O-Al2O3-SiO2 glass-ceramics

Reduction in the temperature coefficient of the optical path length, dS/dT of Li₂O-Al₂O₃-SiO₂ glass-ceramics with near-zero thermal expansion coefficient was attempted using control of the temperature coefficient of electronic polarizability, ?, and the thermal expansion coefficient, α. The dS/dT value of 2.6 mol% B₂O₃-doped glass-ceramic was 12.5  × 10⁻⁶/°C, which was 0.9 ×  10⁻⁶/°C smaller than that of B₂O₃-free glass-ceramic. On the other hand, reduction in dS/dT through B₂O₃ doping was not confirmed in precursor glasses. Results showed that reduction in dS/dT of the glass-ceramic through B₂O₃ doping is caused by the reduction in ?. The reduction in ? from B₂O₃ doping was probably attributable to numerical reduction in non-bridging oxide ions with larger ? value by the concentration of boron ions in the residual glass phase. In addition, application of hydrostatic pressure during crystallization was effective to inhibit precipitation of β-spodumene solid solution, which thereby decreases dS/dT. The dS/dT value of B₂O₃-doped glass-ceramic crystallized under 196 MPa was 11.7 ×  10⁻⁶/°C. That value was slightly larger than that of silica glass. The α value of this glass-ceramic was smaller than that of silica glass.     

Phase separation, crystallization and leaching of microporous glass ceramics in the CaO-TiO2-P2O5 system

Microporous glass ceramics belonging to the CaO-TiO₂-P₂O₅ system were prepared with the assumption of a 2:1 mole ratio for β-Ca₃(PO₄)₂:CaTi₄(PO₄)₆, the anticipated crystalline phases in the end product. The glasses formulated according to the above composition were melted and cast onto a steel mold and were crystallized to glass ceramics containing the above phases. Dilatometric/differential thermal analysis (DTA) techniques were utilized to determine the appropriate phase separation-nucleation and crystallization temperatures. The crystalline products and resulting microstructures in various stages of process were determined and observed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). By leaching the resulting glass ceramics in HCl, β-Ca₃(PO₄)₂ was dissolved out leaving a porous skeleton of CaTi₄(PO₄)₆. It was found that the volume porosity, specific surface area and mean pore diameter of microporous glass ceramics can be managed through the proper selection of heat treatment conditions. In the optimized conditions for fabricating glass ceramics of minimum mean pore size the values of 41 ± 4%, 26 ± 3 m²/g and 14.3 ± 2 nm were obtained for porosity, surface area and pore diameter respectively.     

Crystallization behavior and microstructure of powdered and bulk ZnO-Al2O3-SiO2 glass-ceramics

The crystallization behavior of glass with the composition: 55.6 mol% SiO₂, 22.8 mol% Al₂O₃, 17.7 mol% ZnO and 3.84 mol% of TiO₂ as nucleating agent and with different particle sizes has been studied by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and tranmission electron microscopy (TEM). In glass powders two crystalline phases: zinc-aluminosilicate s.s. with high-quartz structure, Zn_x/2Al_xSi_3−xO₆, (x varies dependent on heat-treatment temperature) and gahnite are formed. The ratio of these phases depends on particle sizes. In bulk glass, however, gahnite is the sole crystalline phase. The composition of initially formed zinc-aluminosilicate s.s. was determined by Rietveld refinement of XRD patterns to be Zn_0.69Al_1.38Si_1.62O₆. With temperature increase, the amount of zinc-aluminosilicate s.s decreased with simultaneous reduce of zinc and aluminum incorporated in the structure. Eventually at 1423 K almost pure high-quartz structure was formed. The activation energies of zinc-aluminosilicate s.s. and gahnite crystallization were determined by non-isothermal method to be 510 ± 18 and 344 ± 17 kJ mol⁻¹, respectively. The latter value matches well with those cited in literature for crystal growth of gahnite in similar glasses. That is attributed to the fact that the high-quartz structure acts as a precursor for gahnite crystallization.     

Dielectric analysis of tungsten-phosphoniobate 20A2O-30WO3 -10Nb2O5 -40P2O5 (A = Li, Na) glass-ceramics

New phosphate glasses of the quaternary system A₂O-Nb₂O₅-WO₃-P₂O₅, where X = Li and Na were prepared by the melt-quenching method. The introduction of WO₃ in the glass composition was based on the proposal of analysing the effect of the diminishing of the molar amount of the alkaline oxide and thus decreasing the molar ratio between network modifiers and network formers (M/F).In the present work we present the preparation of 20A₂O-30WO₃-10Nb₂O₅-40P₂O₅ (A = Li, Na) transparent glasses. These glasses were heat-treated in air, at 550 °C and 650 °C for 4 h. The structure of the obtained samples was studied by X-ray powder diffraction (XRD) and Raman spectroscopy and the morphology by scanning electron microscopy (SEM). The dc (σ_dc), ac (σ_ac) conductivity and dielectric spectroscopy measurements were performed in the function of the temperature and were related with the structural changes of the glass structures.     

Effect of P2O5 on the early stage crystallization of K-fluorrichterite glass-ceramics

The addition of 2 mol% P₂O₅ to stoichiometric K-fluorrichterite (KNaCaMg₅Si₈O₂₂F₂, KFR) has been reported to enhance the mechanical properties and improve the in vitro biocompatibility of this glass-ceramic by promoting the formation of enstatite and fluorapatite (FA). Here, the effect of further increasing the P₂O₅ concentration on phase evolution of KFR has been investigated. XRD data showed that mica crystallized in samples with 4 and 5 mol% P₂O₅ (GP4 and GP5, respectively) at 650 °C, but no diopside was detected at higher temperatures, in contrast with the general phase evolution in KFR based glass-ceramics. More importantly, however, the addition of ?4 mol% P₂O₅ induced phase separation of the glass into a silica glass matrix and phosphate rich droplets prior to crystallization. EDS traces taken from samples heat-treated at 600 °C, revealed that the silica glass matrix was deficient in Mg and unlikely to be the host for crystallization of mica. Conversely, the P₂O₅ rich regions contained excess Mg and were considered to be the host for the formation of mica and FA.     

Non-isothermal crystallization kinetics of ZnO-BaO-B2O3-SiO2 glass

Glass of composition 40SiO₂-30BaO-20ZnO-10B₂O₃ (mol%) was made by conventional melting and casting process. Crystallization kinetics of above glass has been investigated under non-isothermal conditions, using the formal theory of transformations for heterogeneous nucleation. The procedure is applied to the experimental data obtained by differential thermal analysis (DTA), using continuous-heating techniques. The crystallization results are analyzed, and both the activation energy of crystallization process as well as the crystallization mechanism is characterized. Dilatometric measurement of this glass was also done and data obtained was used to calculate the viscosity of the formed glass. Development of crystalline phases on thermal treatments of the glass at various temperatures has been analyzed by X-ray diffraction. Microstructure of the crystalline phases was investigated by scanning electron microscopy (SEM) and the development of various structural features with variation in heat treatment cycle was observed. The nucleation and growth of these phases in the matrix of glass has been described and discussed.     

Effects of Li replacement on the nucleation, crystallization and microstructure of Li2O-Al2O3-SiO2 glass

The Li replacement including the Li₂O replaced by other oxides and the expensive Li₂CO₃ replaced by low-cost spodumene mineral was studied to lower the product cost of (Li₂O-Al₂O₃-SiO₂, LAS) glass ceramic, and the effects of Li replacement on the nucleation, crystallization and microstructure of LAS glass were investigated by the differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that Li₂O replacement increases the crystallization activation energy, lowers the crystal growth, and increases the nucleation and crystallization temperature by restraining the formation of crystalline phases. The Li₂CO₃ replacement decreases the crystallization activation energy, promotes the crystal growth, without affecting the nucleation, and lowers the crystallization temperature by adding some beneficial compositions with mixed alkali effect.     

Optical properties of the optical fiber containing Co doped ZnO-Al2O3-SiO2 glass-ceramics

Optical characteristics of silica glass optical fibers containing Co²⁺ doped ZnO-Al₂O₃-SiO₂ (ZAS) glass-ceramics prepared by slurry-doping method were investigated. The absorption and emission bands of the fibers were found to be originated from the tetrahedral Co²⁺ in ZnAl₂O₄ crystals in ZAS glass-ceramics particles embedded in the core of the fibers. The crystal field strength of the Co²⁺ ions in the optical fiber was found to be smaller than that of the Co²⁺ ions in the bulk ZAS glass-ceramics.     

Bulk crystallisation of (00l) oriented fresnoite Sr2TiSi2O8 in glass-ceramics of the Sr-Ti-Si-K-B-O system

This paper shows that glass-ceramics containing highly surface and bulk preferentially oriented fresnoite Sr₂TiSi₂O₈ crystals can be synthesised by a simple isothermal heat treatment of suitable glass compositions in the Sr-Ti-Si-K-B-O system. For all tested compositions, crystallisation starts from the free surfaces of the specimens and propagates to bulk with time. If most of these compositions lead to (00l) preferential orientation at the specimens' surfaces, bulk crystal texture is very composition dependent. The effects of variation in K₂O and B₂O₃ contents on the crystallisation have been studied. It is shown that low K₂O and high B₂O₃ contents are required to keep the (00l) orientation from the surface into the bulk. This result seems to be explained by the viscosities of the initial and residual glasses at the temperature of crystallisation: a low viscosity leads to a fine and homogeneous microstructure with small and strongly (00l) bulk oriented crystals.     

Phase separation and crystallization in the system SiO2-Al2O3-P2O5-B2O3-Na2O glasses

The phase separation and crystallization behavior in the system (80 − X)SiO₂ · X(Al₂O₃ + P₂O₅) · 5B₂O₃ · 15Na₂O (mol%) glasses was investigated. Glasses with X = 20 and 30 phase separated into two phases, one of which is rich in Al₂O₃-P₂O₅-SiO₂ and forms a continuous phase. Glasses containing a larger amount of Al₂O₃-P₂O₅ (X = 40 and 50) readily crystallize and precipitates tridymite type AlPO₄ crystals. It is estimated that the phase separation occurs forming continuous Al₂O₃-P₂O₅-SiO₂ phase at first, and then tridymite type AlPO₄ crystals precipitate and grow in this phase. Highly transparent glass-ceramics comparable to glass can be successfully obtained by controlling heat treatment precisely. The crystal size and percent crystallinity of these transparent glass-ceramics are 20-30 nm and about 50%, respectively.     

Study of the structural insertion of Al in the Al2O3-SiO2 and Nd2O3-Al2O3-SiO2 glass systems

Glasses in the Al₂O₃-SiO₂ and Nd₂O₃-Al₂O₃-SiO₂ systems were prepared by the sol-gel method. The gel-glass evolution was studied using near-infrared (NIR) and ultraviolet-visible (UV-VIS) spectrophotometry, X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (NMR). The results obtained indicate a relationship between the sample compositions, the treatment temperature and the Al coordination. In the samples of the Nd₂O₃-Al₂O₃-SiO₂ system the densification of the structure, when the treatment temperature increases, leads to the segregation of neodymium oxide particles.     

Crystallization processes of Li2O-Ga2O3-SiO2-NiO system glasses

Crystallization processes of Li₂O-Ga₂O₃-SiO₂-NiO system glasses have been studied by X-ray diffraction, differential calorimetry and optical absorption. Transparent glass-ceramic containing LiGa₅O₈:Ni²⁺ as the sole crystalline phase has been obtained from glass with the composition of 13Li₂O-23Ga₂O₃-64SiO₂-0.1NiO (in mol%) by the heat treatment in the temperature range from 923 to 953 K. It was revealed that the specific surface area of samples enhances crystallization of LiGaSi₂O₆ but obstructed that of LiGa₅O₈. LiGa₅O₈ grew to nano-sized crystallites dispersed in the glass matrices and did not affect the transparency seriously. In contrast, LiGaSi₂O₆ grew to crystallites with diameters more than 100 nm on the surface and made the glasses opaque. Optical absorption measurements revealed that doped Ni²⁺ occupied five-folded trigonal bipyramidal sites in the as-quenched glass matrices but six-folded octahedral sites of precipitated LiGa₅O₈ in the glass-ceramics. It was confirmed that transparent glass-ceramic containing Ni²⁺:LiGa₅O₈ was effectively obtained by the heat treatment at a temperature of 953 K for 10 h.     

Considerations on the structure and physical properties of B2O3-SiO2 and GeO2-SiO2 glasses

Data of density, refractive index and thermal expansion coefficient for B₂O₃-SiO₂ and GeO_2-SiO₂ glasses have been analyzed. The volumes of the structural units are the same found for the vitreous B₂O₃, GeO₂ and SiO₂. The volume of any structural unit is constant over the entire composition region of the glass system. The same has been found for the differential refraction and unit refraction of the structural units in these glasses. Different features are observed for the differential expansion of the structural units. There is a considerable change with composition in the differential expansion of BO₃, GeO₄ and SiO₄ units. The effect is attributed to a change in the asymmetry of vibrations with the number of Si-O-B or Si-O-Ge linkages in the matrix. The thermal expansion coefficient is mainly determined by the contribution of B₂O₃ or GeO₂ in the concerned glasses.     

Electron spin resonance and magnetic studies on CaO-SiO2-P2O5-Na2O-Fe2O3 glasses

Room temperature electron spin resonance (ESR) spectra and temperature dependent magnetic susceptibility measurements have been performed to investigate the effect of iron ions in 41CaO · (52 − x)SiO₂ · 4P₂O₅ · xFe₂O₃ · 3Na₂O (2 ? x ? 10 mol%) glasses. The ESR spectra of the glass exhibited the absorptions centered at g ≈ 2.1 and g ≈ 4.3. The variation of the intensity and linewidth of these absorption lines with composition has been interpreted in terms of variation in the concentration of the Fe²⁺ and Fe³⁺ in the glass and the interaction between the iron ions. The magnetic susceptibility data were used to obtain information on the relative concentration and interaction between the iron ions in the glass.     

Effect of Al2O3 on phase separation and crystallization in ZnO---Al2O3---B2O3---SiO2 glasses

The effect of alumina on the phase separation and the crystallization of the glasses of composition (mol%) 18ZnO·30B₂O₃·52SiO₂ and O-40 Al₂O₃ was studied using an electron microscope and IR spectroscopy. The main crystalline phase appears in the microphase for which the compositions are not nearer to the crystal stoichiometry than the mean. The addition of Al₂O₃ suppresses the immiscibility but enhances the crystallizability.     

Structural study of PbO-MoO3-P2O5 glasses by Raman and NMR spectroscopy

Glasses in the ternary system PbO-MoO₃-P₂O₅ were prepared in three compositional series (100 − x)[0.5PbO-0.5P₂O₅]-xMoO₃ (A), 50PbO-yMoO₃-(50 − y)P₂O₅ (B) and (50 − z)PbO-xMoO₃-50P₂O₅ (C) and their structure was studied by Raman and ³¹P NMR spectroscopies. In the compositional series (100 − x)[0.5PbO-0.5P₂O₅]-xMoO₃ homogeneous glasses were prepared in the concentration region of 0-70 mol% MoO₃. Their glass transition temperature increases with increasing MoO₃ content having a maximum at x = 50 mol% MoO₃. ³¹P MAS NMR spectra reveal that in the glass series (A) the incorporation of MoO₃ results in the shortening of phosphate chains and gradual transformation Q² units into Q² and Q⁰ units, prevailing in glasses with a high MoO₃ content. Octahedral structural units MoO₆ dominate in most glass compositions and they are present also in the structure of Pb(MoO₂)₂(PO₄)₂ compound corresponding to the glass composition 50Pb(PO₃)₂-50MoO₃. The analysis of Raman spectra of glasses of the (B) series with a high MoO₃ content showed the transformation of octahedral MoO₆ units into tetrahedral MoO₄ units.     

Fabrication and properties of novel low-melting glasses in the ternary system ZnO-Sb2O3-P2O5

Glasses in the ternary system ZnO-Sb₂O₃-P₂O₅ were investigated as potential alternatives to lead based glasses for low temperature applications. The glass-forming region of ZnO-Sb₂O₃-P₂O₅ system has been determined. Structure and properties of the glasses with the composition (60 − x)ZnO-xSb₂O₃-40P₂O₅ were characterized by infrared spectra (IR), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results of IR indicated the role of Sb³⁺ as participant in glass network structure, which was supported by the monotonic and remarkable increase of density (ρ) and molar volume (V_M) with increasing Sb₂O₃ content. Glass transition temperature (T_g) and thermal stability decreased, and coefficient of thermal expansion (α) increased with the substitution of Sb₂O₃ for ZnO in the range of 0-50 mol%. XRD pattern of the heat treated glass containing 30 mol% Sb₂O₃ indicated that the structure of antimony-phosphate becomes dominant. The improved water durability of these glasses is consistent with the replacement of easily hydrated phosphate chains by corrosion resistant P-O-Sb bonds. The glasses containing ?30 mol% Sb₂O₃ possess lower T_g (<400 °C) and better water durability, which could be alternatives to lead based glasses for practical applications with further composition improvement.     

Study of CaO-WO3-P2O5 glass system by dielectric properties, IR spectra and differential thermal analysis

Dielectric constant ε^′, loss tanδ and ac conductivity σ_ac of 40CaO-xWO₃-(60−x)P₂O₅ (with 0?x?15) glasses are studied over a range of frequencies and temperature. The dielectric breakdown strength of these glasses is also determined at room temperature. The values of dielectric parameters, viz., ε^′, tanδ and σ_ac of CaO-P₂O₅ glasses are found to decrease with the introduction of WO₃ up to 3 mol% and increase with further increase in the concentration of WO₃; the probable reasons for such an increase are identified and explained with the aid of IR spectra and differential thermal analysis of these glasses. The variation of tanδ with temperature at different frequencies of CaO-P₂O₅ glasses has exhibited dielectric relaxation effects with decreasing relaxation intensity with increase in the concentration of WO₃ from 0 to 3 mol%; such relaxation effects seem to have been absent in glasses containing WO₃ beyond 3 mol%. The relaxation phenomenon has been analysed by a pseudo-Cole-Cole plot method and the possible mechanism responsible for such relaxation effects has been suggested.     

Glasses and glass-ceramics from naturally occurring CaOMgOAl2O3SiO2 materials (II) crystallization behavior

Although shale glasses exhibit surface devitrification when heat treated, the addition of Cr₂O₃ to the glass enables volume crystallization to occur. The mechanisms and kinetics of crystallization for both processes are presented and found to correlate well with existing theories; the Swift equation for surface crystallization and the Johnson-Mehl equation for volume crystallization. Phase separation in the Cr₂O₃-containing glasses promotes the formation of an iron-chrome spinel as nuclei and leads to the development of a fine-grained glass-ceramic.