The Baikal Neutrino Telescope

We review the present status of the Baikal Neutrino Experiment and present results of a search for upward-going atmospheric neutrinos and magnetic monopoles obtained with the detector NT200. The results of a search for very high energy neutrinos are presented and an upper limit on the extraterrestrial diffuse neutrino flux is obtained. We describe the strategy of upgrading the NT200 to NT200+ and creating a detector on the Gigaton scale at Lake Baikal. The first results obtained with the new NT200+ detector as a basic cell of a future Gigaton detector are presented. The text was submitted by the authors in English.     

200 kV/200 kA脉冲源的研制

研制了一台200 kV/200 kA脉冲源,脉冲源由初级储能单元、水介质整形与传输单元、气体开关和负载组成。通过优化设计由2 到1 的水介质变阻抗线、高压气体主开关和陡化开关,使得脉冲功率源在匹配负载下产生输出电压200 kV、电流200 kA、前沿40 ns、脉宽40 ns的高压脉冲。在此脉冲源平台上已开展了低阻抗1 二极管发射特性研究,并且将在高压气体开关、同步触发、二极管等离子体发射诊断等方面发挥作用。     

Annealing effect on ion-beam-sputtered titanium dioxide film

We found that the extinction coefficient of ion-beam-sputtered titanium dioxide films first decreased with increasing annealing temperature then increased drastically when annealing temperature was increased above ~200 degrees C for 24 h of annealing time. The decreasing extinction coefficient with annealing temperature was attributed to a reduction in absorption owing to oxidation of the film by annealing. The film structure remained amorphous to 200 degrees C annealing temperature. The drastic increase of extinction coefficients above ~200 degrees C was associated with the appearance of an anatase polycrystalline structure and was attributed to scattering by the polycrystalline structure. With shorter annealing time the transition temperature from amorphous to polycrystalline anatase was higher. Guidance for reducing the optical loss of laser mirrors is proposed.     

Investigation on Changes in the Miscibility,Morphology, Rheology and Mechanical Behavior of Melt Processed Cellulose Acetate through Adding Polyethylene Glycol as a Plasticizer

Polyethylene glycol (PEG 200) was used as an eco-friendly plasticizer for preparing thermoplastic cellulose acetate (CA) by a twin-screw extruder. The plasticization efficiency of PEG 200 was compared with that of triethyl citrate (TEC). The interaction between polyethylene glycol and CA was investigated by Fourier transform infrared spectroscopy (FT-IR) and differential scanning calorimetry (DSC). Both FT-IR and DSC proved that PEG 200 could form stable and strong hydrogen bonds with CA molecules. Scanning electron microscopy (SEM) revealed that the CA granules were completely disrupted during the extrusion and a continuous and homogeneous phase was observed. The PEG 200-plasticized cellulose acetate (PCA) showed greater viscosity reduction than TEC-plasticized cellulose acetate (TCA) at the same additive levels. Furthermore, the Izod-notched impact strength and elongation at break of PCA were higher than those of TCA. The tensile strength, Izod-notched impact strength and elongation at break of PCA containing 25 wt% PEG 200 reached 31.6 MPa, 20.9 KJ/m² and 80.5%, respectively, as compared to 39.2 MPa, 10.9 KJ/m² and 32.3% for 25 wt% TEC plasticized CA.     

7.5-MHz data-transfer rate with a planar aperture mounted upon a near-field optical slider

We fabricated a planar aperture-mounted (PAM) slider by use of a focused ion beam to demonstrate fast data acquisition for near-field optical data storage. The aperture (200 nm x 500 nm) was formed upon the Ti-coated air-bearing surface of the slider and was directly illuminated with a laser (lambda = 532 nm) beam spot by use of an objective lens (N.A., 0.55). The light transmitted through the aperture was modulated by a Ti-coated SiO(2) disk with 200- and 400-nm-wide line-and-space (L&S) patterns engraved by electron-beam lithography. The optical throughput of the taperless aperture was greater than 0.02. By use of the PAM slider, 400- and 200-nm L&S signals were detected at linear velocities of 6 and 3 m/s, respectively, corresponding to a data-transfer rate of 7.5 MHz.     

13μs,200ns和2ns脉冲电场对酵母菌杀灭效果分析

研究了脉冲宽度对高压脉冲下细胞膜和细胞器膜跨膜电压的影响及细胞膜能量的变化,以及13μs,200ns和2ns脉冲对酿酒酵母(CICC31180)杀灭作用时脉冲数的影响。结果表明,随着脉冲数增加,13μs,200ns和2ns脉冲对啤酒酵母的灭杀效果均增强。在13μs脉宽,14kV电压和50个脉冲数下,酵母达到最小存活率-4.3个对数;在200ns脉宽,40kV电压和500个脉冲数下,酵母达到存活率-2.6个对数;在2ns脉宽,200kV电压和500个脉冲数下,酵母达到存活率-2.8个对数。三种脉冲对酵母菌杀灭的存活率对数与脉冲数的关系表现不是线性的,脉冲数增加到一定程度,存活率下降变缓。在同等灭杀效果-2.0个对数下,2ns脉冲比13μs脉冲在同轴电极中损耗的能量更少。     

高压对米曲霉理化性质影响及诱变的研究

 在100~400 MPa压力、保压20 min的条件下处理酱油酿造菌种——米曲霉,研究高压对米曲霉存活率、形态特征、生理性质、蛋白酶、淀粉酶活性等的影响,并诱变筛选优良菌株。结果表明：高压对米曲霉的存活率、形态特征有明显的影响;压力对蛋白酶及淀粉酶活性的影响也有特异的规律,即在一定压力范围内（0.1~200 MPa）蛋白酶的活性随着压力的增加而减小,但随着压力的进一步升高（200~400 MPa）蛋白酶的活性又逐渐增强,在300 MPa时超过对照组,400 MPa时蛋白酶的活性达到最高值;淀粉酶在0.1~100 MPa时活性下降,在200 MPa时其平均的糊化和糖化活性最强、活力最高,当压力升高活性又开始降低,400 MPa时几乎又回到对照值。另外,高压处理后获得一株理想的变异菌株HP300a：生长速度快、孢子数量多、蛋白酶活力高,且不易被杂菌污染。其成曲的几项主要指标均优于对照株,酿出酱油的几项主要指标也明显优于对照株。为利用高压诱变筛选米曲霉优良菌种、提高酿造酱油产品的产量及质量提供了理论依据,并发现了高压处理米曲霉引起其蛋白酶及淀粉酶活性改变的特殊规律。     

Design and experimental study of a two-dimensional position sensitive X-ray detector

A prototype of a two-dimensional position sensitive X-ray detector was designed and constructed for small angle X-ray scattering experiments at BSFR (Beijing Synchrotron Radiation Facility). The detector is based on MWPC with cathode strip readout, and has a sensitive area of 200 mmx200 mm. The spatial resolution (FWHM) of about 210 μm along the anode wire direction was obtained from the 55Fe X-ray test of the detector.     

CW dye laser operation at 200 W pump power

A continuously operating jet stream dye laser was pumped by a multiwavelength-multimode argon-ion-laser with a pump power up to 200 W. Rhodamine 6G-chloride was dissolved in a water-polyvinylalcohol-ammonyx solution. The dye laser was prism-tunable between 560 and 650 nm with maximum output power at 600 nm. The maximum output power of the cw dye laser was 43 W without tuning element and 33 W with a prism placed inside the cavity. Operation of a jet stream dye laser with a pump power higher than 200 W and an efficiency of about 30% seems to be possible.     

1.55 μm InGaAsP/InP tapered stripe superluminescent diodes with potential optical sensor system applications

We proposed a structure of a 1.55 μm InGaAsP/InP superluminescent diode (SLD) to suppress the lasing action and fabricated laterally tilted multi-quantum well planar buried heterostructure separate confinement heterostructure SLD by using MOCVD and LPE equipments. The fabricated SLD is laterally tilted by 15°. The output power of SLD was 11 mW for 200 mA under pulse driving. The full-width at half-maximum was 42 nm at 200 mA.     

200—350nm合肥同步辐射光谱分布测量

英国国家物理实验室传递标准光源ＭｇＦ２窗口氘灯为标准，测量了２００－３５０ｎｍ合肥同步辐射光谱分布。结果表明，在实验误差范围内，测量结果与依Ｓｃｈｗｉｎｇｅｒ理论计算值具有较好的一致性，２００ｎｍ处偏差为６％，２４０ｎｍ处为１．５％。     

铁冷轧形变以及热处理对形变缺陷的影响

采用常用冷轧设备对铁进行冷轧引入形变缺陷。研究形变量和温度对形变缺陷的影响。形变样品中的微观缺陷、物相结构和形貌分别使用正电子湮没技术（PAT）、X射线衍射仪（XRD）和透射电子显微镜（TEM）进行表征分析。对经过673 K热处理的形变样品前后进行XRD测试,结果显示,随着形变量的增加,样品中晶面方向（200）具有择优生长趋势,673 K热处理后,择优趋势更加明显,同时晶粒的尺寸也增大。利用正电子湮没寿命谱和多普勒展宽能谱对样品中形变缺陷的热力学稳定性进行研究,发现形变引入的空位型缺陷约在673 K回复完毕,723 K后位错缺陷开始回复。The pure iron was cold rolled with the thickness reduction from 0% to 75%. The microstructure defects, crystallographic structure and morphology of deformed specimens were characterized by positron annihilation technique (PAT), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD results show that the intensity of (200) increased with increasing deformation, 673 K heat-treatment promote the preference of (200) and the grain size of (200) was increased. The PAT results show that the vacancy type defect was annihilated at 673 K and the dislocation type defects start to annihilate at 723 K.     

Broadband Antireflection Subwavelength Gratings for Polymethyl Methacrylate Fabricated with Molding Technique

We fabricated a two-dimensional subwavelength grating (SWG) on a polymethyl methacrylate (PMMA) film using a molding technique. A method of fabricating SWGs with high accuracy using a replica technique in an atmospheric environment was proposed. The SWG consisted of tapered gratings with a 200 nm period and a 200 nm deep groove. The reflectivity at wavelengths from 400 nm to 800 nm was measured and compared with the results calculated on the basis of rigorous coupled-wave analysis. At these wavelengths, the reflectivity decreased to approximately half that of the PMMA film.     

Au层退火温度对ZnO/Au/ZnO多层膜的结构、光学及电学性质的影响

采用金属有机化学气相沉积(MOCVD)技术在蓝宝石衬底上制备出晶体质量较好的透明导电的ZnO/Au/ZnO(ZAZ)多层膜,其中,Au夹层是通过射频磁控溅射的方法获得。通过对Au夹层进行不同温度的退火处理,研究了Au层退火温度对ZAZ多层膜的结构特性、电学性能和光学特性的影响。利用原子力显微镜(AFM)、扫描电子显微镜(SEM)、X射线衍射(XRD)仪、霍尔效应测试和透射谱分析等测试手段对ZAZ多层膜的性质进行了分析。测试结果表明,在200 ℃下对Au夹层进行快速退火处理,多层膜的结构、电学和光学性质达到最优,表面等离子体效应也更明显。其中,XRD(002)衍射峰的半高宽为0.14°,电阻率为2.7×10^-3 Ω·cm,载流子浓度为1.07×10²⁰ cm^-3,可见光区平均透过率为75.3%。     

Ferroelastic detwinning of the high-temperature superconductor YBa2Cu3O7-δ

Crystals of YBa₂Cu₃O_7-δ (YBC) were prepared using a flux technique. The as-grown crystals were typically on the order of 200 μm × 200 μm × 50 μm, where the 50 μm dimension is in the c-direction. Ferroelastic behavior was observed by applying a uniaxial stress along the [100]_tet-direction using a specially-designed fixture which was mounted to a programmable hot/cold stage of a polarizing reflected-light microscope. Domain wall motion was observed for temperatures greater than 200°C, and complete poling was accomplished at stresses on the order of 50–100 MPa at temperatures of 350–400°C. An ionic diffusion-activated mechanism is suggested.     

Photodynamic damage (PDD) study using stimulated raman scattering

In the current study, photodynamic damage in different cell cultures was examined using a pulsed laser light. Two different experiments were performed to analyse the photodynamic damage. For the first one, a stimulated Raman scattering laser has been obtained by exciting DMSO liquid with Nd-YAG laser, second harmonic generation, 532 nm. The resulted SRS wavelength is pulsed 630 nm. 1 ml ALA (200 μg/ml) was added to cell suspension and keep it for incubated for 4 h then irradiate the suspension with SRS wavelength 630 nm at different light dose 8, 12, 17, 25, 30, 40, 60, 100, 150, 200 μJ for 10 pluses and obtain the cell degradation. We repeat the step above but for 30 pluses. Finally for the second experiment, 1 ml ALA (200 μg/ml) was added to cell suspension and was incubated for 4 h and then irradiated with Nd-YAG Laser at wavelength 532 nm. Different doses range between 8 up to 200 μJ for 10 pluses only and the cell degradation rate was measured.     

超高压处理对荔枝果肉中两种酶和可溶性蛋白的影响

 为了研究超高压处理对荔枝果肉中过氧化物酶（POD）、果胶甲基酯酶（PME）及可溶性蛋白含量的影响,将荔枝（“淮枝”品种）果肉在100~400 MPa压力、10 ℃温度条件下处理30 min,采用分光光度法测定果肉中POD、PME的活性,用天然凝胶电泳法以及活性染色法测定POD、PME同工酶的变化,用SDS凝胶电泳法测定果肉中可溶性蛋白含量。结果表明：100~200 MPa超高压处理使荔枝果肉中POD活性上升且出现新的同工酶,300~400 MPa超高压处理则使其活性降低且新出现的同工酶消失;100 MPa压力处理使荔枝果肉中PME活性上升且出现新的同工酶,200~400 MPa超高压处理则使其活性降低且新出现的同工酶消失;100 MPa超高压处理使荔枝果肉中可溶性蛋白含量有所增加,而在200~400 MPa压力处理下其含量持续下降。     

诊断LiF单晶弹性变形的瞬态X射线衍射

利用瞬态X射线衍射技术对LiF单晶沿晶向[100]方向冲击加载的晶格变形进行了诊断研究。实验在神光Ⅱ装置的球形靶上进行,北四路激光驱动Cu靶获得的类He线作为X射线背光源,第九路为加载光源,对大小为7mm×7mm、厚300μm的受激光加载的LiF单晶衍射,实验获得了LiF单晶晶面(200)压缩和未压缩状态的衍射信号。实验结果表明:LiF单晶在激光沿[100]方向冲击加载下,晶格发生了弹性变形,(200)晶面间距变小,衍射线上移,晶格压缩量为11%;该瞬态X射线衍射技术可用于冲击加载下的微观动态响应特性测量。     

Interactions between test- and inducer-tone durations in induced loudness reduction

A tone usually declines in loudness when preceded by a more intense inducer tone. This phenomenon is called "loudness recalibration" or "induced loudness reduction" (ILR). The present study investigates how ILR depends on level, loudness, and duration. A 2AFC procedure was used to obtain loudness matches between 2500-Hz comparison tones and 500-Hz test tones at 60 and 70 dB SPL, presented with and without preceding 500-Hz inducer tones. For 200-ms test and comparison tones, the amount of ILR did not depend on inducer level (set at 80 dB SPL and above), but ILR was greater with 200- than with 5-ms inducers, even when both were equally loud. For 5-ms tones, ILR was as great with 5- as with 200-ms inducers and about as great as when test and inducer tones both lasted 200 ms. These results suggest that (1) neither the loudness nor the SPL of the inducer alone governs ILR, and (2) inducer duration must equal or exceed test-tone duration to yield maximal amounts of ILR. Further analysis indicates that the efferent system may be partly responsible for ILR of 200-ms test tones, but is unlikely to account for ILR of 5-ms tones.