镁铝氢氧化物正电溶胶的制备

对镁铝氢氧化物制备的反应条件进行了研究，结果表明：溶胶中镁铝比随混合溶液中镁铝比的增加而增加到一极限值(Mg/Al=2)。随着制备时的镁铝比的增加，溶胶的固含量增加，其产率下降，但ζ电位先上升而后下降。在溶液中镁铝比大于2∶1时，溶胶中只有镁铝氢氧化物。随温度的升高，在胶溶过程中颗粒增大，为六角片状微晶。     

肾上腺髓质素微球复合PLGA/纳米轻基磷灰石支架材料的制备及生物活性评价

利用离子乳化交联法制备了负载肾上腺髓质素的壳聚糖微球,应用热致相分离法制备了乳酸和乙醇酸共聚物/纳米羟基磷灰石(PLGA/nHA)支架材料并在其中包覆载药微球.通过扫描电子显微镜、体外释放行为、材料溶血行为、碱性磷酸酶(ALP)活性的测定、支架材料表面细胞荧光染色和MTT[3-(4,5-二甲基噻唑-2)-2,5-二苯基...     

溶胶-凝胶法制备桥式聚倍半硅氧烷/SiO2光学防潮膜

采用溶胶-凝胶法, 以首次合成的具有桥式结构的间苯二亚甲基二脲基丙基三乙氧基硅烷(m-XDUPTEOS)和正硅酸乙酯(TEOS)为前驱体, 共同水解缩聚制备了不同摩尔配比的桥式聚倍半硅氧烷/SiO₂杂化溶胶, 并旋涂制膜. 通过UV-Vis, AFM和TGA对薄膜的光学性能、表面形貌和热稳定性进行了分析. 结果表明, 该薄膜平整均匀、具有良好的光学透明性、热稳定性和防潮性能.     

非水稀溶液中SiO2包覆ZnO量子点的制备及其发光特性研究

本文利用溶胶-凝胶法在非水稀溶液中制备出SiO₂包覆的ZnO量子点。通过紫外-可见吸收光谱(UV-Vis)和荧光光谱对合成量子点的发光特性进行了研究。结果表明，在n_SiO2:n_ZnO=1∶4的条件下，ZnO量子点的发光性能最佳。经过Brus公式计算，该量子点的平均半径在2.8 nm左右，稳定性显著提高。其荧光光谱在363 nm处有一强而窄的激子发射峰，在519 nm处有一个宽而弱的绿色发射峰。说明SiO₂对ZnO形成了有效包覆，明显减少了ZnO的表面缺陷。     

碳纳米管上原位沉积钯-钴-镍纳米颗粒及其对乙醇氧化的电活性

以水合肼为还原剂,在水和乙醇的混合溶液中制备多壁碳纳米管(MWCNT)负载的纳米镍(Ni/MWCNT)和纳米镍钴(Ni-Co/MWCNT)颗粒,然后将它们分别与氯化钯溶液反应,形成的钯纳米颗粒原位沉积在MWCNT表面,从而得到MWCNT负载的PdNi/MWCNT和Pd-Ni-Co/MWCNT催化剂。SEM和TEM图像显示,MWCNT上的催化剂颗粒是由5~10 nm的小颗粒团聚而成的30~100 nm的大颗粒,三金属催化剂的粒径比双金属的粒径小,在MWCNT上的分散度更高。ICP和EDS分析显示,Pd直接还原并包覆在纳米镍和纳米镍钴表面;采用循环伏安和计时电流技术,研究了催化剂在碱性溶液中对乙醇氧化的电催化活性,结果表明,Pd-Ni-Co/MWCNT催化剂对乙醇氧化具有强的电催化活性,乙醇氧化对应的峰电流密度达101.8 m A·cm~(-2),并且催化剂催化活性稳定。     

TEOS-MTES基SiO2溶胶微结构的SAXS研究

正硅酸乙酯(TEOS)为前驱体,在碱性条件下制备含有无定形SiO2颗粒的溶胶,以甲基三乙氧基硅烷(MTES)在酸性条件下获得聚甲基硅氧链,二者混合后应用同步辐射X射线进行混合溶胶的SAXS散射强度测定,计算了溶胶的平均回转半径、平均粒径、两相界面层厚度、散射体体积分数、两相间比表面积等参数,辅以光子相关光谱法(PCS)和透射电子显微镜(TEM)观测溶胶粒度,证实SiO2颗粒被MTES混合物连接成族团.实验发现所测混合溶胶样品均表现出对Porod定理的负偏离,说明溶胶中颗粒与溶剂之间存在很明显的两相间界面层.     

碳纳米管上原位沉积钯-钴-镍纳米颗粒及其对乙醇氧化的电活性

以水合肼为还原剂,在水和乙醇的混合溶液中制备多壁碳纳米管(MWCNT)负载的纳米镍(Ni/MWCNT)和纳米镍钴(Ni-Co/MWCNT)颗粒,然后将它们分别与氯化钯溶液反应,形成的钯纳米颗粒原位沉积在MWCNT表面,从而得到MWCNT负载的Pd-Ni/MWCNT和Pd-Ni-Co/MWCNT催化剂。SEM和TEM图像显示,MWCNT上的催化剂颗粒是由5~10 nm的小颗粒团聚而成的30~100 nm的大颗粒,三金属催化剂的粒径比双金属的粒径小,在MWCNT上的分散度更高。ICP和EDS分析显示,Pd直接还原并包覆在纳米镍和纳米镍钴表面;采用循环伏安和计时电流技术,研究了催化剂在碱性溶液中对乙醇氧化的电催化活性,结果表明,Pd-Ni-Co/MWCNT催化剂对乙醇氧化具有强的电催化活性,乙醇氧化对应的峰电流密度达101.8 mA·cm^-2,并且催化剂催化活性稳定。     

一种新型凝胶态聚合物电解质的制备和性能

采用一种新型胶联剂新戊二醇二丙烯酸酯(noepentyl glycol diacrylate, NPGDA)和聚偏氟乙烯-六氟丙烯(poly(vinylidene fluoride-co-hexafluoropropylene), PVDF-HFP), 液态电解液组成电解质混合溶液, 然后加入引发剂并加热引发聚合反应制备了一种具有互穿聚合物网络结构的凝胶态聚合物电解质, 可以用于制备聚合物锂离子二次电池. 考察了不同PVDF-HFP/NPGDA质量比对凝胶态聚合物电解质性能的影响. 结果表明, PVDF-HFP/NPGDA质量比可以影响凝胶态聚合物电解质的结构形貌、电化学特性以及聚合物锂离子二次电池的性能. 研究发现, 当m(PVDF-HFP)/m(NPGDA)＝1:1时制备的凝胶态聚合物电解质具有较高的离子电导率和电化学稳定窗口, 室温下分别为6.99×10^-3 S•cm^-1和4.8 V(vs Li⁺/Li), 以其为电解质制备的聚合物锂离子二次电池具有较好的电化学性能.     

聚乙二醇包裹羰基铁核壳粒子的制备及水基磁流变液的性能

以羰基铁粉(CI)为原料用共溶胶-凝胶反应制备CI/聚乙二醇核壳复合粒子，并将其与水组成了磁流变液. 用SEM、TEM、FT-IR和VSM表征了核壳复合粒子的微观结构和静磁特性，并测试了水基磁流变液的性能. 结果表明，核壳复合粒子表面有SiO_x和聚乙二醇的包覆层，它有较好的亲水性和优良的软磁特性，用它组成的水基磁流变液具有抗沉降性优良、零场粘度低、磁流变效应显著等特点.     

双金属核壳结构负载型Au@Ag/TiO2催化剂的制备及表征

利用溶胶法制备了Au核Ag壳(Au@Ag)结构复合纳米粒子,用粉末-溶胶法和水热合成法使其负载于TiO₂纳米粒子上,利用紫外-可见吸收光谱﹑X射线粉末衍射﹑透射电子显微镜对复合结构材料进行了结构表征,并对其光催化消除臭氧的性能进行了研究。结果表明,制备方法、Au/Ag化学计量比及金属负载量等对光催化消除臭氧的活性均有很大影响。采用粉末-溶胶法制备的1%-Au@Ag/TiO₂(n_Au/n_Ag=1∶3)催化剂,由于TiO₂表面沉积的Au@Ag金属颗粒尺寸小且分散度高,而且1%的金属担载量有利于光生电子空穴的有效分离,光催化消除臭氧的活性最高。     

Incorporation of nanohydroxyapatite and vitamin D3 into electrospun PCL/Gelatin scaffolds: The influence on the physical and chemical properties and cell behavior for bone tissue engineering

Scaffold, an essential element of tissue engineering, should provide proper physical and chemical properties and evolve suitable cell behavior for tissue regeneration. Polycaprolactone/Gelatin (PCL/Gel)‐based nanocomposite scaffolds containing hydroxyapatite nanoparticles (nHA) and vitamin D3 (Vit D3) were fabricated using the electrospinning method. Structural and mechanical properties of the scaffold were determined by scanning electron microscopy (SEM) and tensile measurement. In this study, smooth and bead‐free morphology with a uniform fiber diameter and optimal porosity level with appropriate pore size was observed for PCL/Gel/nHA nanocomposite scaffold. The results indicated that adding nHA to PCL/Gel caused an increase of the mechanical properties of scaffold. In addition, chemical interactions between PCL, gelatin, and nHA molecules were shown with XRD and FT‐IR in the composite scaffolds. MG‐63 cell line has been cultured on the fabricated composite scaffolds; the results of viability and adhesion of cells on the scaffolds have been confirmed using MTT and SEM analysis methods. Here in this study, the culture of the osteoblast cells on the scaffolds showed that the addition of Vit D3 to PCL/Gel/nHA scaffold caused further attachment and proliferation of the cells. Moreover, DAPI staining results showed that the presence and viability of the cells were greater in PCL/Gel/nHA/Vit D3 scaffold than in PCL/Gel/nHA and PCL/Gel scaffolds. The results also approved increasing cell proliferation and alkaline phosphatase (ALP) activity for MG‐63 cells cultured on PCL/Gel/nHA/Vit D3 scaffold. The results indicated superior properties of hydroxyapatite nanoparticles and vitamin D3 incorporated in PCL/Gel scaffold for use in bone tissue engineering.     

Corrosion protection of AA6061-T4 alloy by sol–gel derived micro and nano-scale hydroxyapatite (HA) coating

Micron and nano-scale hydroxyapatite (HA) were coated successfully on AA6061-T4 substrates by sol–gel method. Besides, the effects of coating thickness on adhesion strength and corrosion behaviour of the coatings were studied. Corrosion resistance was measured by potentiodynamic polarization test using a potentiostat under in vitro conditions. The coatings before and after corrosion tests were characterized by adhesion tests, a scanning electron microscopy attached with EDS and X-ray diffraction analysis. The results revealed that all the coatings exhibit a passive behaviour in Ringer’s solution. Specimens coated with nano-scale HA had the higher corrosion resistance than micro-scale coatings. The highest corrosion resistance appeared to be for the ~30 μm nano-scale HA coated substrates. However, for micro-scale HA coatings, the highest adhesion resistance was obtained at ~30 μm film thickness.     

Nano‐hydroxyapatite/polyamide66 composite tissue‐engineering scaffolds with anisotropy in morphology and mechanical behaviors

Based on a biomimetic conception, nano‐hydroxyapatite (n‐HA)/polyamide66 (PA66) composite scaffolds were prepared with anisotropic properties both in morphology and mechanical behavior. A novel improved thermally induced phase separation (TIPS) technique was developed to generate orientation‐structured scaffolds for tissue engineering. The physiochemical, morphological, and mechanical properties of the resultant scaffolds were evaluated. According to the results, the improved TIPS method exhibited good processability and reproducibility and enabled the composite scaffolds to have a high content of inorganic fillers. The morphological study proved that the n‐HA/PA66 scaffolds exhibited unidirectional microtubular architecture with high porosity (ca. 80–85%) and an optimal pore size ranging from 200 to 500 μm. Besides, the effect of n‐HA content on the morphology of the scaffolds was studied, and the results indicated that the obtained scaffolds presented an improvement in anisotropic morphology with increase of n‐HA content. The anisotropy was also evaluated in the mechanical properties of the scaffolds, that is, the longitudinal compressive strength and modulus were ～1.5 times of the transverse ones. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 658–669, 2009     

A composite polyaniline/graphene–coated polyamide6 nanofiber mat for electrochemical applications

In this study, polyamide6 (PA6) nanofiber mats were fabricated through the electrospinning process. The nanofibers were coated by polyaniline (PANI) using the in situ polymerization of aniline in the presence of graphene oxide. The composite of the PANI/graphene oxide–coated nanofiber mat was treated with hydrazine monohydrate to reduce graphene oxide to graphene, and this was followed by the reoxidation of PANI. Field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), wide angle X‐ray diffraction (WAXD), thermal gravimetric analysis (TGA), tensile strength tests, electrical conductivity measurements, cyclic voltammetry (CV), and charge/discharge measurements were conducted on the composite PA6/graphene nanofiber mats. It was found that the surface of the PA6 nanofibers was coated uniformly with the granular PANI and graphene oxide. Besides, the composite nanofibers showed good tensile and thermal properties. Their electrical conductivity and specific capacitance, when used as a separator in the cell, were 1.02 × 10^?4 S/cm and 423.28 F/g, respectively. Therefore, the composite PANI/reduced graphene oxide–coated PA6 nanofiber mats could be regarded as suitable candidates for application in energy storage devices.     

羟基磷灰石／胶原／植物多酚复合材料的研究

以原花色素、茶多酚等植物多酚为交联剂,采用低温原位合成法制备羟基磷灰石/胶原/植物多酚(HA/COL/PP)复合材料。对材料的形貌、热稳定性、溶胀性质进行了表征。结果表明,植物多酚的加入使复合材料中各成分结合更紧密,增加了复合材料的热稳定性,降低了复合材料的溶胀度。比较研究表明,添加原花色素对上述性能的改善更有效。为了考察加入植物多酚后复合材料的生物活性,分别对羟基磷灰石/胶原/原花色素(HA/COL/PA)、羟基磷灰石/胶原/茶多酚(HA/COL/TP)复合材料进行了体外矿化能力研究,观察到两种材料的表面都形成了新的矿化沉积层,说明加入了植物多酚不影响复合材料的体外矿化能力。因而,羟基磷灰石/胶原/植物多酚复合材料是一种有潜力的骨替代材料。     

原位沉淀法制备CS/nHA多孔复合支架及其性能

通过原位沉淀法和冷冻相分离技术得到含有钙磷前驱体(CaP)的初始多孔支架, 利用多孔支架表面原位生成的壳聚糖(CS)膜减缓NaOH溶液中OH^-离子的渗透速率, 以达到纳米羟基磷灰石(nHA)缓慢形成的目的, 从而制得nHA 分布均匀的CS/nHA多孔复合支架. 利用扫描电镜(SEM)和万能试验机研究复合支架的结构和性能, 发现nHA为针状结构, 长度为80200 nm, 宽度为2050 nm. 随着nHA含量的增加, 复合支架的孔隙率下降, 由(93.8±3.3)%降至(87.7±3.8)%, 压缩强度则逐渐提高, 由(0.5±0.09) MPa增加至(1.5±0.06) MPa. 当复合支架中nHA质量分数为25%时, 未发现nHA团聚现象, nHA均匀地分布于CS基体中. 通过红外光谱(FTIR)、 X射线衍射(XRD)及X射线光电子能谱(XPS)等分析推断, nHA与CS之间可能存在配位和氢键作用. 细胞实验结果表明, CS/nHA多孔复合支架具有良好的生物相容性, 细胞在支架内部贴壁黏附生长. CS/nHA多孔复合支架有望在骨组织工程领域具有良好的应用前景.     

纳米羟基磷灰石/丝素蛋白复合支架材料的降解特性及生物相容性研究

应用共混法制备了纳米羟基磷灰石/丝素蛋白复合支架材料, 通过体外降解和细胞培养实验研究了复合支架材料的降解特性和生物相容性. 体外降解实验结果显示, 复合支架材料具有稳定的降解能力; 在降解过程中, 羟基磷灰石由于与降解液发生钙、磷等离子的交换, 使其结晶得到了进一步生长和完善. 利用细胞计数法、四甲基偶氮唑盐(MTT)比色法和碱性磷酸酶(ALP)活性测定等分析了复合支架材料的生物相容性, 结果表明, MG63细胞在复合支架材料上具有良好的粘附、增殖能力, 并可引起早期的骨分化. 因此, 纳米羟基磷灰石/丝素蛋白复合支架作为骨组织工程的支架材料具有良好的应用前景.     

聚醚醚酮复合材料表面生物活性涂层的制备与性能

以聚醚醚酮/钡玻璃粉(PEEK-BGF)复合材料为基体, 通过硅烷偶联剂, 在复合材料表面构建具有生物活性的纳米羟基磷灰石(nHA)和甲基丙烯酸酯基的光固化树脂复合涂层. 采用扫描电子显微镜(SEM)和X射线光电子能谱(XPS)分析了材料表面形貌和元素分布, 测试了涂层与复合材料之间的粘接强度. 通过检测大鼠成骨细胞总蛋白含量和碱性磷酸酶表达水平, 评价新型光固化纳米羟基磷灰石/聚甲基丙烯酸酯(nHA/PMMA)复合涂层的生物活性. 研究结果表明, nHA填充的光固化复合材料形成粗糙的表面, 随着nHA的填充量提高, 涂层表面生物学活性得到提高.     

In situ biomimetic formation of nano‐hydroxyapatite crystals on chitosan microspheres

Chitosan (CS) is a biocompatible, noncytotoxic biomaterial used before as base material for composites. On the other hand, nano‐hydroxyapatite (nHA) is one of the main components of human bones, highly used for biomedical applications. In this work, CS microspheres were produced under a W/O emulsion system. CS microspheres with calcium ions were then exposed to Na₃PO₄ solution. In situ biomimetic nHA crystals were formed on CS microspheres to generate 15.14 ± 3.15‐μm composite microspheres. The microspheres were subsequently seeded with MG63 osteoblasts to observe their cell responses. All microspheres were characterized via scanning electron microscopy (SEM), phase‐contrast photomicroscopy, and X‐ray diffraction (XRD) analysis. The results showed flake‐like shape and islet‐like growth of nHA depositions presented on the surface of the CS microspheres. In vitro tests indicated that the CS/nHA microparticles were not only biocompatible but also enhanced cell adhesion and elongation due to the in situ biomimetic synthesis method.     

Electrogenerated Chemiluminescence of Tris(2,2′‐bipyridyl)ruthenium(II) Immobilized in Humic Acid‐Silica‐Poly(vinyl alcohol) Composite Films

In this paper, we report the first attempt to use humic acid (HA) as modifiers to prepare the organic‐inorganic hybrid modified glassy carbon electrodes based on HA‐silica‐PVA (poly(vinyl alcohol)) sol‐gel composite. Electroactive species of tris(2,2′‐bipyridyl)ruthenium(II) (Ru(bpy) ) can easily incorporate into the HA‐silica‐PVA films to form Ru(bpy) modified electrodes. The amount of Ru(bpy) incorporated in the composite films strongly depends on the amount of HA in the hybrid sol. Electrochemical and electrogenerated chemiluminescence (ECL) of Ru(bpy) immobilized in HA‐silica composite films coated on a glassy carbon electrode have been studied with tripropylamine (TPA) as the coreactant. The analytical performance of this modified electrode was evaluated in a flow injection analysis (FIA) system with a homemade flow cell. The as‐prepared electrode showed good stability and high sensitivity. The detection limits (S/N=3) were 0.050 μmol L^?1 for TPA and 0.20 μmol L^?1 for oxalate, and the linear ranges were from 0.10 μmol L^?1 to 1.0 mmol L^?1 for TPA and from 1.0 μmol L^?1 to 1.0 mmol L^?1 for oxalate, respectively. The resulting electrodes were stable over two months.