A comparative study of the ionic keV X-ray line emission from plasma produced by the femtosecond,picosecond and nanosecond duration laser pulses

We report here an experimental study of the ionic keV X-ray line emission from magnesium plasma produced by laser pulses of three widely different pulse durations (FWHM) of 45 fs, 25 ps and 3 ns, at a constant laser fluence of ∼1.5 × 10⁴ J cm^− 2. It is observed that the X-ray yield of the resonance lines from the higher ionization states such as H- and He-like ions decreases on decreasing the laser pulse duration, even though the peak laser intensities of 3.5 × 10¹⁷ W cm^− 2 for the 45 fs pulses and 6.2 × 10¹⁴ W cm^− 2 for the 25 ps pulses are much higher than 5 × 10¹² W cm^− 2 for the 3 ns laser pulse. The results were explained in terms of the ionization equilibrium time for different ionization states in the heated plasma. The study can be useful to make optimum choice of the laser pulse duration to produce short pulse intense X-ray line emission from the plasma and to get the knowledge of the degree of ionization in the plasma.     

Synthesis of w-CdS quantum dots and discovery of intense sub band emission owing to longitudinal optical phonons

Cadmium sulfide (CdS) quantum dots (QDs), capped with cetyltrimethylammonium bromide (CTAB), and was synthesized as stable, aqueous, colloidal nanofluid. A series of nine intense, well-resolved emission lines between 400 and 750 nm were observed for the first time when exciting the CdS QDs nanofluid with a 355-nm high energy pulsed Nd:YAG laser radiation. The energy separation between any two successive emission lines equals to the characteristic overtone energy of 295 cm⁻¹ of the longitudinal optical phonon of CdS QDs. In addition, recording the PL spectrum by using a xenon broad band light source resulted in the observation of this characteristic overtone energy of 295 cm⁻¹. In agreement with this photoluminescence characteristic, Raman spectrum exhibited four prominent Stokes lines with Raman shift equal to and multiple of 295 cm⁻¹. Transmission electron microscopy investigation showed that the CdS QDs were spherical with hexagonal wurtzite structure and had a size in the range of 5–10 nm.     

Application of 940 nm high-power DFB lasers for line-broadening measurements at normal pressure using a robust and compact setup

High-power distributed-feedback (DFB) lasers for the wavelength range near 940 nm (i.e. about 10,600 cm⁻¹) were used for line-broadening measurements of individual rotational-vibrational absorption lines of water vapour at atmospheric pressure using a minimalist set-up. The laser has a maximum output power larger than 500 mW. Over the whole power range from threshold to maximum power, it operates in single mode operation with a tuning range of 4.7 nm, i.e. 50 cm⁻¹, at 20°C. With an emission line-width ≤2 MHz (0.66×10⁻⁴ cm⁻¹), the device is well suited for high-resolution spectroscopy.     

Laser induced breakdown spectroscopy of germane plasma induced by IR CO2 pulsed laser

Laser-induced breakdown spectroscopy (LIBS) in germane (GeH₄), initially at room temperature and pressures ranging from 2 to 10 kPa, was studied using a high-power transverse excitation atmospheric (TEA) CO₂ laser (λ=10.653 μm, τ _FWHM=64 ns and power densities ranging from 0.28 to 5.52 GW cm⁻²). The strong emission spectrum of the generated plasma is mainly due to electronic relaxation of excited Ge, H and ionic fragments Ge⁺, Ge²⁺ and Ge³⁺. The weak emission is due to molecular bands of H₂. Excitation temperatures of 8100±300 K and 23,500±2500 K were estimated by Ge atomic and Ge⁺ singly ionized lines, respectively. Electron number densities of the order of (0.7–6.2)×10¹⁷ cm⁻³ were deduced from the Stark broadening of several atomic Ge lines. The characteristics of the spectral emission intensities from different species have been investigated as functions of the germane pressure and laser irradiance. Optical breakdown threshold intensities in germane at 10.653 μm have been determined. The mechanism of initiation of the laser-induced plasma in germane has been analyzed.     

Spectroscopic properties of 1.8 μm emission of thulium ions in germanate glass

A new type host of germanate glass (GeO₂− BaO−BaF₂−Ga₂O₃−La₂O₃) codoped with Tm₂O₃ has been investigated for application as laser material. It possesses a large emission cross section with the value of 9.3×10⁻²¹ cm² at 1.8 μm. Judd-Ofelt intensity parameters and radiative transition probability are calculated and analyzed by Judd-Ofelt theory and absorption spectra. The infrared emission spectra at 1.8 μm have been obtained by using a 794 nm laser diode as excitation resource. The emission intensity ratio of 1.8 (³F₄→³H₆) to 1.47 μm (³H₄→³F₄) increases, while the experimental lifetime of the Tm³⁺:³H₄ level decreases by increasing Tm₂O₃ concentration, which is attributed to the presence of a cross relaxation process. The most intensive emission at 1.8 μm is achieved from the germanate glass with the concentration of Tm₂O₃ reaches 1.0 wt%. The extended overlap integral method is used to calculate the microparameter of the energy transfer and the critical distance, which are derived to better understand the energy transfer process of thulium ions in the germanate glass responsible for emission at 1.8 μm.     

Spectroscopic characterization and diode-pumped 910 nm laser of Nd:LiLuF4 crystal

Polarized absorption and fluorescence spectra Nd³⁺-doped LiLuF₄ single crystal were investigated. The peak emission cross section at 905 and 910 nm are 0.97 × 10⁻²⁰ and 0.82 × 10⁻²⁰ cm², respectively. Two samples with different dimensions were tested in the laser experiments. With a laser-diode as the pump source, a maximum 1.17 W laser output at 910 nm has been obtained with a slope efficiency of 16.3% with respect to the pump power.     

Modelling of a simple Dy<Superscript>3+</Superscript> doped chalcogenide glass fibre laser for mid-infrared light generation

A simple Dy³⁺-doped chalcogenide glass fibre laser design for mid-infrared light generation is studied using a one dimensional rate equation model. The fibre laser design employs the concept of cascade lasing. The results obtained demonstrate that efficient cascade lasing may be achieved in practice without the need for fibre grating fabrication, as a sufficient level of feedback for laser action is provided by Fresnel light reflection at chalcogenide glass fibre–air interfaces. Further enhancement of the laser efficiency can be achieved by terminating one of the fibre ends with a mirror. A numerical analysis of the effect of the Dy³⁺ doping concentration and fibre loss on the laser operation shows that with 5 W of pump power, at 1.71 μm wavelength, output powers above 100 mW at ∼ 4.5 μm wavelength can be achieved with Dy³⁺ ion concentrations as low as 3 × 10¹⁹ cm⁻³, when fibre loss is of the order 1dB/m.     

Mid-infrared upconversion spectroscopy based on a Yb:fiber femtosecond laser

We present a system for molecular spectroscopy using a broadband mid-infrared laser with near-infrared detection. Difference frequency generation of a Yb:fiber femtosecond laser produced a mid-infrared (MIR) source tunable from 2100–3700 cm⁻¹ (2.7–4.7 μm) with average power up to 40 mW. The MIR spectrum was upconverted to near-infrared wavelengths for broadband detection using a two-dimensional dispersion imaging technique. Absorption measurements were performed over bandwidths of 240 cm⁻¹ (7.2 THz) with 0.048 cm⁻¹ (1.4 GHz) resolution, and absolute frequency scale uncertainty was better than 0.005 cm⁻¹ (150 MHz). The minimum detectable absorption coefficient per spectral element was determined to be 4.4×10⁻⁷ cm⁻¹ from measurements in low pressure CH₄, leading to a projected detection limit of 2 parts-per-billion of methane in pure nitrogen. In a natural atmospheric sample, the methane detection limit was found to be 30 parts-per-billion. The spectral range, resolution, and frequency accuracy of this system show promise for determination of trace concentrations in gas mixtures containing both narrow and broad overlapping spectral features, and we demonstrate this in measurements of air and solvent samples.     

Absorption saturation properties and laser Q-switch performance of Cr<Superscript>5+</Superscript>-doped YVO<Subscript>4</Subscript> crystal

The ground-state and excited-state absorption cross sections of a Cr⁵⁺:YVO₄ single crystal were determined by the intensity-dependant transmission measurements to be(2.0±0.4)×10^-18 cm² and less than 0.1×10^-18 cm² at 1.08 μm, respectively. The bleaching relaxation time of the Cr⁵⁺:YVO₄ crystal was estimated to be 3.5±1.5 ns. Passive Q-switching of a diode-pumped Yb³⁺:YVO₄ laser with the Cr⁵⁺:YVO₄ saturable absorber was realized. PACS 42.55.Xi; 42.60.Gd; 42.70.Hj     

Strong amplified spontaneous emission and lasing from a narrow-gap RF-excited Ar-He-Xe gas mixture

The performance of a RF excited cw atomic xenon laser at wavelengths of 2.03 μm and 2.65 μm was studied theoretically and experimentally as a function of electrode distance. Results for inter-electrode distances from 2 to 0.25 mm are presented. A high pumping rate resulted in strong 40 mW cw amplified spontaneous emission at 2.65 μm wavelength from the configuration with the smallest distance of 0.25 mm between the electrodes. The maximum laser output of 2.7 W (0.24 W/cm³) was obtained with an active medium volume of 2×15×370 mm³ whereas the maximum specific output of 1.9 W/cm³ was received for an active medium volume of 0.25×2.25×370 mm³. A fluid model of the RF discharge was developed to analyze the laser behavior for different distances between the electrodes. Received: 30 November 1999 / Revised version: 21 April 2000 / Published online: 6 September 2000     

Adaptive synthesis of optical pattern for photonic crystal lithography

The two-photon absorption spectrum and cross-section (δ) for ruby (Cr³⁺:sapphire) have been measured over the 0.8–1.2 μm wavelength range at 25°C. Absolute values of δ were obtained by comparing the fluorescence yield for two-photon excitation with that for single-photon excitation of the same ionic transition under identical illumination conditions. The maximum values of δ are 4.6×10⁻³ GM for o-polarisation and 5.9×10⁻³ GM for e-polarisation at 840 nm. The relevance of these measurements to distributed optical fibre sensing is briefly discussed.     

2.7 μm fluorescence radiative dynamics and energy transfer between Er3+ and Tm3+ ions in fluoride glass under 800 nm and 980 nm excitation

A detailed study of the fluorescence radiative dynamics and energy transfer processes between Er and Tm ions in the Er³⁺/Tm³⁺ doped fluoride glass is reported. The fluorescence properties of 2.7 μm emission, other infrared and visible emissions are investigated under different selective laser excitations. Three Judd–Ofelt intensity parameters, energy transfer microparameters and efficiency have been determined and discussed. It is found that present Er³⁺/Tm³⁺ doped fluoride glass possesses large calculated emission cross section (8.98×10^–21 cm²) around 2.7 μm. The more suitable pumping scheme for laser applications at 2.7 μm laser is 980 nm excitation for Er³⁺/Tm³⁺ doped fluoride glass.     

Optical absorption in early stage low temperature laser produced plasma

We describe a new technique to measure the UV/visible absorption spectrum of the ablated material during the laser pulse. The technique utilizes the continuum emission from one laser produced plasma as a light source to measure the absorption properties of a second laser produced plasma which is formed on a semi-transparent target with an array of 40 μm holes. A 6 ns, 1064 nm laser was used to ablate a Ag target and the plasma absorption was measured in the range 450–625 nm for a laser fluence of 1 J cm⁻². The total absorption cross-section is (0.5–1.5)×10⁻¹⁷ cm² in the range 450–540 nm. By comparing the measured absorption with a calculation using the plasma spectroscopy code FLYCHK it can be concluded that, in the wavelength region examined here, the absorption is mainly due to bound-bound transitions.     

Spectroscopic properties of Nd<Superscript>3+</Superscript>:CaNb<Subscript>2</Subscript>O<Subscript>6</Subscript> crystal

The absorption spectra, fluorescence spectrum and fluorescence decay curve of Nd³⁺ ions in CaNb₂O₆ crystal were measured at room temperature. The peak absorption cross section was calculated to be 6.202×10⁻²⁰ cm² with a broad FWHM of 7 nm at 808 nm for E//a light polarization. The spectroscopic parameters of Nd³⁺ ions in CaNb₂O₆ crystal have been investigated based on Judd-Ofelt theory. The parameters of the line strengths Ω _t are Ω ₂=5.321×10⁻²⁰ cm²,Ω ₄=1.734×10⁻²⁰ cm²,Ω ₆=2.889×10⁻²⁰ cm². The radiative lifetime, the fluorescence lifetime and the quantum efficiency are 167 μs, 152 μs and 91%, respectively. The fluorescence branch ratios are calculated to be β ₁=36.03%,β ₂=52.29%,β ₃=11.15%,β ₄=0.533%. The emission cross section at 1062 nm is 9.87×10⁻²⁰ cm².     

Enhanced field emission from pulsed laser deposited nanocrystalline ZnO thin films on Re and W

Nanocrystalline ZnO thin films have been deposited on rhenium and tungsten pointed and flat substrates by pulsed laser deposition method. An emission current of 1 nA with an onset voltage of 120 V was observed repeatedly and maximum current density ∼1.3 A/cm² and 9.3 mA/cm² has been drawn from ZnO/Re and ZnO/W pointed emitters at an applied voltage of 12.8 and 14 kV, respectively. In case of planar emitters (ZnO deposited on flat substrates), the onset field required to draw 1 nA emission current is observed to be 0.87 and 1.2 V/μm for ZnO/Re and ZnO/W planar emitters, respectively. The Fowler–Nordheim plots of both the emitters show nonlinear behaviour, typical for a semiconducting field emitter. The field enhancement factor β is estimated to be ∼2.15×10⁵ cm⁻¹ and 2.16×10⁵ cm⁻¹ for pointed and 3.2×10⁴ and 1.74×10⁴ for planar ZnO/Re and ZnO/W emitters, respectively. The high value of β factor suggests that the emission is from the nanometric features of the emitter surface. The emission current–time plots exhibit good stability of emission current over a period of more than three hours. The post field emission surface morphology studies show no significant deterioration of the emitter surface indicating that the ZnO thin film has a very strong adherence to both the substrates and exhibits a remarkable structural stability against high-field-induced mechanical stresses and ion bombardment. The results reveal that PLD offers unprecedented advantages in fabricating the ZnO field emitters for practical applications in field-emission-based electron sources.     

Three-dimensional simulation of laser–plasma-based electron acceleration

A sequential three-dimensional (3D) particle-in-cell simulation code PICPSI-3D with a user friendly graphical user interface (GUI) has been developed and used to study the interaction of plasma with ultrahigh intensity laser radiation. A case study of laser–plasma-based electron acceleration has been carried out to assess the performance of this code. Simulations have been performed for a Gaussian laser beam of peak intensity 5 × 10¹⁹ W/cm² propagating through an underdense plasma of uniform density 1 × 10¹⁹ cm^− 3, and for a Gaussian laser beam of peak intensity 1.5 × 10¹⁹ W/cm² propagating through an underdense plasma of uniform density 3.5 × 10¹⁹ cm^− 3. The electron energy spectrum has been evaluated at different time-steps during the propagation of the laser beam. When the plasma density is 1 × 10¹⁹ cm^− 3, simulations show that the electron energy spectrum forms a monoenergetic peak at ~14 MeV, with an energy spread of ±7 MeV. On the other hand, when the plasma density is 3.5 × 10¹⁹ cm^− 3, simulations show that the electron energy spectrum forms a monoenergetic peak at ~23 MeV, with an energy spread of ±7.5 MeV.     

Synthesis of LaB6 micro/nano structures using picosecond (Nd:YAG) laser and its field emission investigations

Micro/nano structures have been obtained by laser surface treatment on sintered LaB₆ pellets employing a picosecond pulsed Nd:YAG laser at a pressure of ∼1×10⁻³ mbar. The X-ray diffraction pattern of the laser treated pellet shows a set of well defined diffraction peaks, indexed to the cubic phase of LaB₆ only. The scanning electron microscope studies reveal formation of micro and nano structures upon laser treatment and the resultant surface morphology is found to be strongly influenced by the laser fluence. Field electron emission studies made on the LaB₆ pellet, treated with optimized laser fluence, have been performed in a planar diode configuration under ultra high vacuum conditions. The threshold field required to draw an emission current density of ∼10 μA/cm² has been found to be ∼2.3 V/μm and a current density of ∼530 μA/cm² has been drawn at an applied field of 5.2 V/μm. The Fowler-Nordheim plot is found to be linear in accordance with the quantum mechanical tunneling phenomenon, confirming the metallic nature of the emitter. The emission current at the pre-set value ∼10 μA shows very good stability over a period of more than 3 hours. The present results emphasize the effectiveness of a picosecond laser treatment towards fabrication of a nano metric LaB₆ emitter for high current density applications.     

Thin TiO2 grown by metal–organic chemical vapor deposition on (NH4)2S x -treated InP

The electrical characteristics of thin TiO₂ films prepared by metal–organic chemical vapor deposition grown on a p-type InP substrate were studied. For a TiO₂ film of 4.7 nm on InP without and with ammonium sulfide treatment, the leakage currents are 8.8×10⁻² and 1.1×10⁻⁴ A/cm² at +2 V bias and 1.6×10⁻¹ and 8.3×10⁻⁴ A/cm² at −2 V bias. The lower leakage currents of TiO₂ with ammonium sulfide treatment arise from the improvement of interface quality. The dielectric constant and effective oxide charge number density are 33 and 2.5×10¹³ cm², respectively. The lowest mid-gap interface state density is around 7.6×10¹¹ cm⁻² eV⁻¹. The equivalent oxide thickness is 0.52 nm. The breakdown electric field increases with decreasing thickness in the range of 2.5 to 7.6 nm and reaches 9.3 MV/cm at 2.5 nm.     

Growth and laser properties of Nd<Superscript>3+</Superscript>:Sr<Subscript>6</Subscript>YSc(BO<Subscript>3</Subscript>)<Subscript>6</Subscript> crystal

The crystal of Nd³⁺:Sr₆YSc(BO₃)₆ with dimensions of O 19×42 mm³ was grown by the Czochralski method. It’s spectral and laser properties have been investigated. The absorption cross section is 1.47×10^-20 cm² with a FWHM 12.0 nm at 807 nm, the emission cross section is 1.57×10^-19 cm² at 1060 nm, and the fluorescence lifetime is 76 μs at room temperature. The maximum laser output is 25.7 mJ at 1.06 μm pumped by a single Xenon flash lamp and the overall and average slope efficiencies are 0.12% and 0.09%, respectively. The laser energy threshold value is 1.28 J. PACS 42.55.Rz; 42.70.Hj; 78.20.-e     

Optical spectroscopy and laser parameters of Zn2+/Er3+/Yb3+-tridoped LiNbO3 crystal

The Zn/Er/Yb:LiNbO₃ and Er/Yb:LiNbO₃ crystals were grown by the Czochralski technique. The laser characteristics of 1.54 μm emission were predicted based on the Judd–Ofelt theory, and the intensity parameters Ω_t (Ω₂=7.23×10^?20 cm², Ω₄=3.15×10^?20 cm² and Ω₆=1.43×10^?20 cm²) were obtained. The stimulated emission cross sections (σ_em) at 1.54 μm emission in Zn/Er/Yb:LiNbO₃ were calculated based on the McCumber theory and the Füchtbauer–Ladenburg theory. The gain cross section spectrum of Zn/Er/Yb:LiNbO₃ crystal was also investigated. Under 980 nm excitation, a lenghthening lifetime of 1.54 μm emission and an enhancement of green upconversion emission were observed for Zn/Er/Yb:LiNbO₃ crystal. The studies on the power pump dependence and the upconversion mechanism suggested that both green and red upconversion emissions were populated via the three-photon process, and Zn²⁺ ion tridoping increases the probability of cross relaxation process between the two neighboring Er³⁺ ions.