Continuous flow homogeneous catalysis using supercritical fluids

The continuous flow hydroformylation of 1-octene catalysed by Rh/[RMIM][Ph(2)PC(6)H(4)SO(3)](R = 1-propyl, 1-pentyl or 1-octyl) dissolved only in the steady state reaction mixture and using scCO(2) as a transport vector for both substrates and products gives rates up to 160-240 catalyst turnovers h(-1) with low rhodium leaching over a 12 h period at a total pressure of 125-140 bar.     

新型离子液体介质中长链烯烃氢甲酰化反应

合成和表征了离子液体[Rmim][p-CH3C6H4SO3](R=CH3(CH2)n—, n=3, 7, 11, 15), 并以所合成的离子液体为反应介质, 考察了水溶性铑膦络合物HRh(CO)(TPPTS)3[TPPTS: P(m-C6H4SO3Na)3]对长链烯烃氢甲酰化反应的催化性能. 结果表明, 离子液体[Rmim][p-CH3C6H4SO3]中R基团链长的变化对催化活性具有重要的影响；而在相同离子液体中, 氢甲酰化反应活性随着烯烃链长的增加明显下降. 与文献报道中广泛使用的离子液体[Bmim]BF4、[Bmim]PF6相比, 该催化体系对长链烯烃氢甲酰化反应具有更好的活性和化学选择性, 在3.0 MPa, 100 ℃的条件下, 1-己烯氢甲酰化反应转化频率(TOF)高达2736 h-1. 反应完成后, 水溶性铑膦络合物能很好地溶解在离子液体中, 与有机物自动分层, 催化剂的循环使用易于实现.     

The effect of pH on the reactions of catalytically important RhI complexes in aqueous solution: reaction of [RhCl(tppms)3] and trans-[RhCl(CO)(tppms)2] with hydrogen (TPPMS = mono-sulfonated triphenylphosphine).

Hydrolysis and hydrogenation of [RhCl(tppms)3] (1) and trans-[RhCl(CO)(tppms)2] (2) was studied in aqueous solutions in a wide pH range (2 < pH < 11) in the presence of excess TPPMS (3-diphenylphosphinyl-benzenesulfonic acid sodium salt). In acidic solutions hydrogenation of 1 yields a mixture of cis-mer- and cis-fac-[RhClH2(tppms)3] (3a,b) while in strongly basic solutions [RhH(H2O)(tppms)3] (4) is obtained, the midpoint of the equilibrium between these hydride species being at pH 8.2. The paper gives the first successful 1H and 31P NMR spectroscopic characterization of a water soluble rhodium(I)-monohydride (4) bearing only monodentate phosphine ligands. Hydrolysis of 2 is negligible below pH 9 and its hydrogenation results in formation of [Rh(CO)H(tppms)3] (5), which is an analogue to the well known and industrially used hydroformylation catalyst [Rh(CO)H(tppts)3] (6) (TPPTS = 3,3',3'-phosphinetriyltris(benzenesulfonic acid) trisodium salt). It was shown by pH-potentiometric measurements that formation of 5 is strongly pH dependent in the pH 5-9 range, this gives an explanation for the observed but previously unexplained pH dependence of several hydroformylation reactions. Conversely, the effect of pH on the rate of hydrogenation of maleic and fumaric acid catalyzed by 1 in the 2 < pH < 7 range can be adequately described by considering solely the changes in the ionization state of these substrates. All these results warrant the use of buffered (pH-controlled) solutions for aqueous organometallic catalysis.     

First application of supported ionic liquid phase (SILP) catalysis for continuous methanol carbonylation

A solid, silica-supported ionic liquid phase (SILP) rhodium iodide Monsanto-type catalyst system, [BMIM][Rh(CO)2I2]-[BMIM]I-SiO2, exhibits excellent activity and selectivity towards acetyl products in fixed-bed, continuous gas-phase methanol carbonylation.     

Synthesis of cyano-bridged magnetic nanoparticles using room-temperature ionic liquids

A principally new exploit of ionic liquids as an alternative reaction medium in the synthesis of cyano-bridged coordination-polymer nanoparticles is reported. Stable colloid solutions containing nanoparticles of cyano-bridged molecule-based magnets, M)[Fe(CN)6]2/[RMIM][BF4] (M2+=Ni, Cu, Co) and Fe4[Fe(CN)6]3/[RMIM][BF4] (R=1-butyl (BMIM), 1-decyl (DMIM)), were prepared in the corresponding 1-R-3-methylimidazolium tetrafluoroborate [RMIM][BF4], which acts as both a stabilising agent and a solvent. By varying the length of the N-alkyl chain on the imidazolium cation of [RMIM]+ and the temperature, the growing process can be controlled to produce nanoparticles of different sizes. By studying the magnetic properties of frozen colloids it is shown that the relaxation of magnetisation is strongly influenced by interparticle interactions, which leads to the appearance of spin-glass-like dynamics in these systems.     

Step-by-step uncoordination of the pyrazolyl rings of hydrotris(pyrazolyl)borate ligands in comlexes of Rh and RhIII

Compounds of rhodium(I) and rhodium(III) that contain ancillary hydrotris(pyrazolyl)borate ligands (Tp') react with monodentate and bidentate tertiary phosphanes in a step-wise manner, with incorporation of P-donor atoms and concomitant replacement of the Tp' pyrazolyl rings. Accordingly, [Rh(kappa3-TpMe2)(C2H4)(PMe3)] (1b), converts initially into [Rh(kappa2-TpMe2)-(PMe3)2] (3), and then into [Rh(kappa1-TpMe2)-(PMe3)3] (2) upon interaction with PMe3 at room temperature, in a process which can be readily reversed under appropriate experimental conditions. Full disengagement of the Tp' ligand is feasible to give Tp' salts of rhodium(I) complex cations, for example, [Rh(CO)(dppp)2]-[TpMe2,4-Cl] (5; dppp = Ph2P(CH2)3PPh2), or [Rh(dppp)2][TpMe2,4-Cl] (6). Bis(hydride) derivatives of rhodium(III) exhibit similar substitution chemistry, for instance, the neutral complex [Rh(Tp)-(H)2(PMe3)] reacts at 20 degrees C with an excess of PMe3 to give [Rh(H)2-(PMe3)4][Tp] (9b). Single-crystal X-ray studies of 9b, conducted at 143 K, demonstrate the absence of bonding interactions between the [Rh(H)2(PMe3)4]+ and Tp ions, the closest Rh...N contact being at 4.627 A.     

Intermolecular alkene and alkyne hydroacylation with beta-S-substituted aldehydes: mechanistic insight into the role of a hemilabile P-O-P ligand

A straightforward to assemble catalytic system for the intermolecular hydroacylation reaction of beta-S-substituted aldehydes with activated and unactivated alkenes and alkynes is reported. These catalysts promote the hydroacylation reaction between beta-S-substituted aldehydes and challenging substrates, such as internal alkynes and 1-octene. The catalysts are based upon [Rh(cod)(DPEphos)][ClO(4)] (DPEphos=bis(2-diphenylphosphinophenyl)ether, cod=cyclooctadiene) and were designed to make use of the hemilabile capabilities of the DPEphos ligand to stabilise key acyl-hydrido intermediates against reductive decarbonylation, which results in catalyst death. Studies on the stoichiometric addition of aldehyde (either ortho-HCOCH(2)CH(2)SMe or ortho-HCOC(6)H(4)SMe) and methylacrylate to precursor acetone complexes [Rh(acetone)(2)(DPEphos)][X] [X=closo-CB(11)H(6)Cl(6) or [BAr(F) (4)] (Ar(F)=3,5-(CF(3))(2)C(6)H(3))] reveal the role of the hemilabile DPEphos ligand. The crystal structure of [Rh(acetone)(2)(DPEphos)][X] shows a cis-coordinated diphosphine ligand with the oxygen atom of the DPEphos distal from the rhodium. Addition of aldehyde forms the acyl hydride complexes [Rh(DPEphos)(COCH(2)CH(2)SMe)H][X] or [Rh(DPEphos)(COC(6)H(4)SMe)H][X], which have a trans-spanning DPEphos ligand and a coordinated ether group. Compared to analogous complexes prepared with dppe (dppe=1,2-bis(diphenylphosphino)ethane), these DPEphos complexes show significantly increased resistance towards reductive decarbonylation. The crystal structure of the reductive decarbonylation product [Rh(CO)(DPEphos)(EtSMe)][closo-CB(11)H(6)I(6)] is reported. Addition of alkene (methylacrylate) to the acyl-hydrido complexes forms the final complexes [Rh(DPEphos)(eta(1)-MeSC(2)H(4)-eta(1)-COC(2)H(4)CO(2)Me)][X] and [Rh(DPEphos)(eta(1)-MeSC(6)H(4)-eta(1)-COC(2)H(4)CO(2)Me)][X], which have been identified spectroscopically and by ESIMS/MS. Intermediate species in this transformation have been observed and tentatively characterised as the alkyl-acyl complexes [Rh(CH(2)CH(2)CO(2)Me)(COC(2)H(4)SMe)(DPEphos)][X] and [Rh(CH(2)CH(2)CO(2)Me)(COC(6)H(4)SMe)(DPEphos)][X]. In these complexes, the DPEphos ligand is now cis chelating. A model for the (unobserved) transient alkene complex that would result from addition of alkene to the acyl-hydrido complexes comes from formation of the MeCN adducts [Rh(DPEphos)(MeSC(2)H(4)CO)H(MeCN)][X] and [Rh(DPEphos)(MeSC(6)H(4)CO)H(MeCN)][X]. Changing the ligand from DPEphos to one with a CH(2) linkage, [Ph(2)P(C(6)H(4))](2)CH(2), gave only decomposition on addition of aldehyde to the acetone precursor, which demonstrated the importance of the hemiabile ether group in DPEphos. With [Ph(2)P(C(6)H(4))](2)S, the sulfur atom has the opposite effect and binds too strongly to the metal centre to allow access to productive acetone intermediates.     

功能离子液体复合体系中钯催化的Heck偶联反应

在[BMIM][TPPMS]离子型膦配体和碱性离子液体 [BMIM][OAc] 组成的功能离子液体复合体系中, PdCl2(CH3CN)2可以有效地催化溴苯和丙烯酸乙酯的交叉偶联(Heck)反应, 产物肉桂酸乙酯(反式)的收率达到60%. 锚定在功能离子液体复合体系中的Pd催化剂循环使用11次后仍保持良好的活性和稳定性. 该催化剂体系的良好活性和稳定性可归因于三个方面: [BMIM][TPPMS]和[BMIM][OAc]间的协同配位效应; 以[BMIM][OAc]作为Heck反应的缚酸剂, 避免了无机盐粘稠物的形成; 生成的副产物[BMIM]Br可以有效溶解钯黑, 避免了钯黑的析出. 该离子液体催化体系对不同底物的Heck偶联反应也表现出良好的普适性.     

硅胶键合膦的制备及其对铑络合物催化1-辛烯氢甲酰化反应的影响

以硅胶为载体, 采用键合接枝法将2-(二苯膦基)乙基三乙氧基硅烷(DPPES)共价键合于硅胶表面, 制备了性能优良的硅胶键合型膦配体(以SiO₂(PPh₂)表示). 以SiO₂(PPh₂)为配体, Rh(acac)(CO)₂ (acac:乙酰丙酮)为催化前体, 负载铑膦络合物催化剂(SiO₂(PPh₂)/Rh)在1-辛烯氢甲酰化反应中原位生成. 对生成的负载型催化剂和硅胶键合型膦配体进行了傅里叶变换红外(FTIR)光谱表征, 考察了膦/铑摩尔浓度比([P]/[Rh])、温度等因素对铑催化的长链1-辛烯氢甲酰化反应的影响. 结果表明, 膦/铑摩尔浓度比的增加能显著提高反应的成醛选择性, 降低铑的流失. 在[P]/[Rh]=12、363 K、2.0 MPa、1.5 h 的温和反应条件下, 1-辛烯转化率和成醛选择性分别可达98.4%和95.3%, 其催化活性与DPPES或三苯基膦(TPP)作配体时的均相铑催化相近. 催化剂循环4 次后, 反应活性无明显下降, 1-辛烯转化率均在97.0%左右, 经电感耦合等离子体原子发射光谱(ICP-AES)检测,有机相中铑流失低于0.1%.     

一种难溶多金属氧酸盐配位聚合物的重构与表征

利用电沉积法将不溶于常规无机和有机溶剂的多金属氧酸盐基的配位聚合物1, [{La(H₂O)₅·(dipic)}{La(H₂O)(dipic)}]₂{Mo₈O₂₆}·10H₂O溶解于离子液体[RMIM][HT]或[RMIM][HP]中, 在恒电位下电解, 得到多金属氧酸盐基的配位聚合物膜. 应用红外光谱、X射线光电子能谱和XRD粉末衍射等方法研究多金属氧酸盐基配位聚合物膜的结构, 发现其与多金属氧酸盐基配位聚合物有相同的结构. 实现了多金属氧酸盐基配位聚合物在电极上的重构设计以及多金属氧酸盐基的配位聚合物的二次加工成型.     

Supported ionic liquid phase catalysis with supercritical flow

Rapid hydroformylation of 1-octene (rates up to 800 h(-1)) with the catalyst remaining stable for at least 40 h and with very low rhodium leaching levels (0.5 ppm) is demonstrated when using a system involving flowing the substrate, reacting gases and products dissolved in supercritical CO(2) (scCO(2)) over a fixed bed supported ionic liquid phase catalyst.     

The rate-determining step in the rhodium-xantphos-catalysed hydroformylation of 1-octene

The rate-determining step in the hydroformylation of 1-octene, catalysed by the rhodium-Xantphos catalyst system, was determined by using a combination of experimentally determined (1)H/(2)H and (12)C/(13)C kinetic isotope effects and a theoretical approach. From the rates of hydroformylation and deuterioformylation, a small (1)H/(2)H isotope effect of 1.2 was determined for the hydride moiety of the rhodium catalyst. (12)C/(13)C isotope effects of 1.012(1) and 1.012(3) for the alpha-carbon and beta-carbon atoms of 1-octene were determined, respectively. Both quantum mechanics/molecular mechanics (QM/MM) and full quantum mechanics calculations were carried out on the key catalytic steps, for "real-world" ligand systems, to clarify whether alkene coordination or hydride migration is the rate-determining step. Our calculations (21.4 kcal mol(-1)) quantitatively reproduce the experimental energy barrier for CO dissociation (20.1 kcal mol(-1)) starting at the (bisphosphane)RhH(CO)(2) resting state. The barrier for hydride migration lies 3.8 kcal mol(-1) higher than the barrier for CO dissociation (experimentally determined trend approximately 3 kcal mol(-1)). The computed (1)H/(2)H and (12)C/(13)C kinetic isotope effects corroborate the results of the energy analysis.     

双功能离子液体的合成及二氧化碳捕集性能

采用两步法合成了新型功能化离子液体1-甲氧基乙基-3-甲基咪唑甘氨酸([C_3O_1mim][Gly]),并研究了其对CO_2的吸收性能.利用核磁共振、红外光谱及热重分析等手段进行表征,验证了该离子液体的结构,且发现其具有较高的热稳定性.对比单乙醇胺(MEA),考察了[C_3O_1mim][Gly]在不同温度下对CO_2的捕集能力,结果表明,[C_3O_1mim][Gly]在40℃下的吸收容量可达1.26 mol CO_2/mol IL,远高于MEA,这表明[C_3O_1mim][Gly]对CO_2具有良好的吸收能力,吸收容量随着温度升高而降低.该离子液体同时具有良好的循环稳定性,进行5次吸收解吸操作后仍可保持较高的CO_2吸收量.对该离子液体吸收CO_2进行了动力学研究,结果表明,Pseudo-second-order模型能够较好地描述该吸收过程.     

Hydroformylation of 1-octene using low-generation Rh(i) metallodendritic catalysts based on a tris-2-(2-pyridyliminoethyl)amine scaffold

The synthesis and characterization of low-generation pyridylimine Rh(i) metallodendrimers is described. These metallodendrimers were obtained via a Schiff base condensation of tris-2-(aminoethyl)amine with 2-pyridinecarboxaldehyde to afford the tris-2-(2-pyridylimine ethyl) amine ligand (1). Subsequent complexation reactions with [RhCl(CO)(2)](2) and [RhCl(COD)](2) yielded the corresponding metal-containing dendrimers containing -RhCl(CO) and -Rh(COD) moieties on the periphery. These new rhodium metallodendrimers (2 and 3) and their precursor ligand (1) are thermally stable and have been characterized using (1)H NMR, (13)C NMR, (31)P NMR, FT-IR spectroscopy, elemental analysis as well as mass spectrometry. The Rh(i) metallodendrimers are highly active and chemo- and regioselective in the hydroformylation of 1-octene. Aldehydes were favoured at moderate to high temperatures (95 °C and 75 °C) and pressure (30 bars), while more iso-octenes were formed at low temperature (55 °C) and pressures (5 and 10 bars). The mononuclear analogues (5 and 6) also produced more aldehydes (albeit showing catalyst decomposition at 95 °C and 75 °C, 30 bars) and these aldehydes were mostly branched.     

光促进下N,N-二甲基甲酰胺作为一氧化碳源的烯烃氢酯化反应

 研究了光照下以N,N-二甲基甲酰胺(DMF)为一氧化碳源的烯烃氢酯化反应. 结果表明,在常温常压和光照射条件下DMF可以分解得到CO,新生成的CO在光促进下可以直接与CH3OH-DMF溶液中的底物1-辛烯在温和条件和非贵金属钴化合物(Co(OAc)2,CoCl2,Co(en)3Cl2和大环钴[Co(14)4,11-二烯-N4]I2)催化下进行氢酯化反应,反应中DMF既是溶剂,又是原料. H13CON(CH3)2同位素示踪实验证实了这一结果. 在反应体系中通入二氧化碳可以大大提高反应的转化率、产率及选择性. 13CO2同位素示踪实验表明,CO2并未参与产物的形成,其作用是中和DMF分解产生的HN(CH3)2,从而有利于DMF的光促分解.     

Catalytic performance of [Bmim][Co(CO)4] functional ionic liquids for preparation of 1,3-propanediol by coupling of hydroesterification-hydrogenation from ethylene oxide

In this paper, synthesis of 1,3-propanediol (1,3-PDO) through coupling of hydroesterification-hydrogenation from ethylene oxide (EO) catalyzed by 1-butyl-3-methylimidazolium cobalt tetracarbonyl [Bmim][Co(CO)₄] functional ionic liquid which was prepared by metathesis reaction between [Bmim]Cl and KCo(CO)₄ has been studied. The structure of [Bmim][Co(CO)₄] was characterized by FT-IR and ¹H NMR. Using [Bmim][Co(CO)₄] as catalyst and [Bmim]PF₆ as solvent, 1,3-PDO was prepared for the first time by coupling of hydroesterifaction of EO and hydrogenation of methyl 3-hydroxypropionate (3-HPM). The yield of 3-HPM can reach 90.8%, while the yield of 1,3-PDO up to 82.9%. The catalyst can be separated from the product mixture by extraction with deionized water and recycled several times without significant loss of catalytic efficiency. A possible reaction mechanism has also been proposed.     

Synthesis and reactivity of fluorinated ferracarborane anions

The ferracarborane [N(PPh3)2][6,6,6,10,10,10-(CO)6-closo-6,10,1-Fe2CB7H8] reacts in CH2Cl2 with 3 molar equivalents of Ag[PF6] to yield the trifluoro-substituted species [N(PPh3)2][7,8,9-F3-6,6,6,10,10,10-(CO)6-closo-6,10,1-Fe2CB7H5]. Compound undergoes structural rearrangement in toluene at reflux temperatures, forming [N(PPh3)2][8,9,10-F3-6,6,6,7,7,7-(CO)6-closo-6,7,1-Fe2CB7H5]. Alternatively, reaction of either or with a 10-fold excess of Ag[PF6] in CH2Cl2 forms two species: namely, [N(PPh3)2][2,7,9,10-F4-6,6,6,8,8,8-(CO)6-closo-6,8,1-Fe2CB7H4], in which one further B-F substitution has occurred and the {Fe2CB7} cluster core has rearranged, plus a mono-iron co-product, [N(PPh3)2][3,8,9-F3-7,7,7-(CO)3-closo-7,1-FeCB7H5] that is formed by polyhedral contraction. Treatment of with [NO][BF4] in CH2Cl2 results in CO substitution at the 4-connected iron vertex [Fe10], producing the zwitterionic complex [7,8,9-F3-6,6,6,10,10-(CO)5-10-NO-closo-6,10,1-Fe2CB7H5]. Addition of Me3NO to a mixture of and PEt3 in CH2Cl2 also results in CO substitution, forming the isomeric species [N(PPh3)2][7,8,9-F3-6,6,m,10,10-(CO)5-n-PEt3-closo-6,10,1-Fe2CB7H5] [m=6, n=10; m=10, n=6] in a 5:1 ratio. Treatment of with [NO][BF4] and then CNBut in CH2Cl2 allows further, successive CO substitution at Fe10 to yield first a neutral, zwitterionic complex [7,8,9-F3-6,6,6,10-(CO)4-10-NO-10-PEt3-closo-6,10,1-Fe2CB7H5] and then [7,8,9-F3-6,6,6-(CO)3-10-CNBut-10-NO-10-PEt3-closo-6,10,1-Fe2CB7H5]. The molecular structures of compounds and have been established by X-ray diffraction.     

A fully integrated high-throughput screening methodology for the discovery of new polyolefin catalysts: discovery of a new class of high temperature single-site group (IV) copolymerization catalysts

For the first time, new catalysts for olefin polymerization have been discovered through the application of fully integrated high-throughput primary and secondary screening techniques supported by rapid polymer characterization methods. Microscale 1-octene primary screening polymerization experiments combining arrays of ligands with reactive metal complexes M(CH(2)Ph)(4) (M = Zr, Hf) and multiple activation conditions represent a new high-throughput technique for discovering novel group (IV) polymerization catalysts. The primary screening methods described here have been validated using a commercially relevant polyolefin catalyst, and implemented rapidly to discover the new amide-ether based hafnium catalyst [eta(2)-(N,O)[bond](2-MeO[bond]C(6)H(4))(2,4,6-Me(3)C(6)H(2))N]Hf(CH(2)Ph)(3) (1), which is capable of polymerizing 1-octene to high conversion. The molecular structure of 1 has been determined by X-ray diffraction. Larger scale secondary screening experiments performed on a focused 96-member amine-ether library demonstrated the versatile high temperature ethylene-1-octene copolymerization capabilities of this catalyst class, and led to significant performance improvements over the initial primary screening discovery. Conventional one gallon batch reactor copolymerizations performed using selected amide-ether hafnium compounds confirmed the performance features of this new catalyst class, serving to fully validate the experimental results from the high-throughput approaches described herein.     

Speciation and kinetics related to catalytic carbonylation in the presence of cis-[Ir(CO)2I2]P(C6H5)4 under CO and H2 pressures

The differences in the reactivities of the square-planar complexes cis-[Rh(CO)2I2]- (1) and cis-[Ir(CO)2I2]- (2), involved in the catalytic carbonylation of olefins, are investigated, with P(C6H5)4+ as the counterion, by ambient- and high-pressure NMR and IR spectroscopy. Under an elevated pressure of CO, 1 and 2 form the [M(CO)3I] complexes with the equilibrium constants KIr approximately 1.8 x 10(-3) and KRh approximately 4 x 10(-5). The ratio KIr/KRh close to 50 shows that, under catalytic conditions (a few megapascals), only complex 1 remains in the anionic form, while a major amount of the iridium analogue 2 is converted to a neutral species. The oxidative addition reactions of HI with 1 and 2 give two monohydrides of different geometries, mer,trans-[HRh(CO)2I3]- (3) and fac,cis-[HIr(CO)2I3]- (4), respectively. Both hydrides are unstable at ambient temperature and form, within minutes for Rh and within hours for Ir, the corresponding cis-[M(CO)2I2]- (1 or 2) and [M(CO)2I4]- (5 or 6) species and H2. When an H2 pressure of 5.5 MPa is applied to a nitromethane solution of complex 2, ca. 50% of 2 is transformed to cis-dihydride complexes. The formation of cis,cis,cis-[IrH2(CO)2I2]- (8a) is followed by intermolecular rearrangements to form cis,trans,cis-[IrH2(CO)2I2]- (8b) and cis,cis,trans-[IrH2(CO)2I2]- (8c). A small amount of a dinuclear species, [Ir2H(CO)4I4]x- (9), is also observed. The formation rate constants for 8a and 8b at 262 K are k1(262) = (4.42 +/- 0.18) x 10(-4) M-1 s-1, k-1(262) = (1.49 +/- 0.07) x 10(-4) s-1, k2(262) = (2.81 +/- 0.04) x 10(-5) s-1, and k-2(262) = (5.47 +/- 0.16) x 10(-6) s-1. The two equilibrium constants K1(262) = [8a]/([2][H2]) = 2.97 +/- 0.03 M-1 and K2(262) = [8b]/[8a] = 5.13 +/- 0.10 show that complex 8b is the thermodynamically stable addition product. However, no similar H2 addition products of the rhodium analogue 1 are observed. The pressurization with H2 of a solution containing 2 and 6 give the monohydride 4, the dihydrides 8a and 8b, the dinuclear complex 9, and the two new complexes [Ir(CO)2I3] (10) and [HIr(CO)2I2] (11). The reactions of the iridium complexes with H2 and HI are summarized in a single scheme.     

A novel ligand-free palladium catalytic system with SO3H-functional ionic liquids as cocatalyst for amidocarbonylation reaction

Effects of Lewis acid BF3·OEt2, and BrCnsted acids TsOH, CF3COOH, H3PO4, and HCIO4 as cocatalyst respectively on the ligand-free palladium-catalyzed amidocarbonylation were investigated. SO3H-functional ionic liquids 1-methyl-3-（4-sulfonic acid）butylimidazolium hydrosulfate [MIm（CH2）4803H][HSO4] and 1-methyl-3-（4-sulfonic acid）butylimidazolium triflate [MIm（CH2）4SO3H][OTf] were firstly employed as cocatalysts instead of these Lewis acid and Brφnsted acids. By using a ligand-free and weak corrosive catalyst in situ prepared form PdBr2, LiBr.H2O, and [MIm（CH2）4SO3H][OTf], the arnidocarbo- nylation of benzaldehyde, acetamide, and CO could proceed smoothly and afford N-acetyl-α-phenylglycine with yield of 58% in [C6mim]PF6 medium.