反应器型式对甲烷低温等离子体转化制C2烃的影响

就不同反应器对甲烷常压低温等离子体转化制C2烃的影响进行了研究。结果表明,相同的甲烷停留时间和相同甲烷流率下,反应器A和B中反应的主要产物是乙炔,乙烯和乙烷的含量较少,积炭量较多;而反应器C和D中反应的主要产物为乙烷和丙烷,乙烯和乙炔含量较少,积炭量很少。反应积炭对反应器A中甲烷转化率影响很大,对于产物选择性影响不大,而对反应器C中的反应影响较小。根据产物分布可知,在反应器A和B中,由于电子具有很高的能量和密度,甲烷主要解离为碳原子;而在反应器C及D中,由于电子能量和密度较低,甲烷主要解离为CH3自由基。     

Conversion of natural gas to C2 hydrocarbons via cold plasma technology

The plasma technology served as a tool in unconventional catalysis has been used in natural gas conversion, because the traditional catalytic methane oxidative coupling reaction must be performed at high temperature on account of the stability of methane molecule. The focus of this research is to develop a process of converting methane to C2 hydrocarbons with non-equilibrium plasma technology at room temperature and atmospheric pressure. It was found that methane conversion increased and the selectivity of C2 hydrocarbons decreased with the voltage. The optimum input voltage range was 40-80 V corresponding to high yield of C2 hydrocarbons. Methane conversion decreased and the selectivity of C2 hydrocarbons increased with the inlet flow rate of methane. The proper methane flow rate was 20-40 ml/min (corresponding residence time 10-20 s). The experimental results show that methane conversion was 47% and the selectivity of C2 hydrocarbons was 40% under the proper condition using atmospheric DBD cold plasma technology. It was found that the breakdown voltage of methane VB was determined by the type of electrode and the discharge gap width in this glow discharge reactor. The breakdown voltage of methane VB,min derived from the Paschen law equation was established.     

滑动弧电极放电等离子体作用甲烷制C2烃的工艺

采用刀片式不锈钢电极放电反应器,以Ar气为稀释气,研究了等离子体作用下甲烷转化制C2烃的工艺条件。考察了CH4流量、高频电源输入电压和电极间距等参数对甲烷转化率、C2烃选择性、收率和反应表观能耗的影响。结果表明,增加CH4流量,表观能耗随之降低;当输入电压和电极间距较小时,甲烷转化率随输入电压和电极间距的增大而增大,但输入电压和电极间距过大时,C2烃收率明显下降,积碳严重。在CH4流量14 mL/min、Ar气流量60 mL/min、高频电源输入电压22 V、电流0.44 A、电极间距4 mm的优化条件下,甲烷最高转化率为43.1%,C2烃收率、选择性和表观能耗分别为40.1%、93.2%和2.41 MJ/mol。C2烃中不饱和烃的体积分数可达95%以上。     

Methane Decomposition and C2 Hydrocarbon Formation under the Condition of DC Discharge Plasma

The infrared emission spectra of methane, H, CH and C2 hydrocarbons in natural gas were measured. The processes of methane decomposition and formation of C2 hydrocarbons were studied. The experiment shows that methane decomposition can be divided into three periods as the reaction proceeds.In the first period, a large number of free radicals were formed. While in the last period, the formation of C2 hydrocarbons and the decrease of free radicals were observed. The time and conditions of methane decomposition and formation of C2 hydrocarbons are different.     

Methane conversion by an air microwave plasma

Activation of methane is carried out by means of an air microwave plasma (2.45 GHz). The experiments cover the absorbed microwave power range 350–650 W (20–50 W cm³ with 17–62%, of methane in the gas mixture, with pressures of 10–66 mbar and flow rates of 140700 ml min¹. Methane, dioxygen, and dinitrogen consumptions as well as C₂ hydrocarbons, carbon monoxide, and dihydrogen yields are analyzed hr gas chromatography. The distance of methane addition from the end of the discharge plays an important role in the composition and the concentration of the products obtained. This distance mainly determines the energy concentrated in the active species of the plasma when they react with methane. A kinetic mechanism jar the activation and decay of inethane and for the formation of C₂ hydrocarbons and carbon monoxide is discussed based on the experimental results and kinetic data in the literature.     

Methane coupling in microwave plasma under atmospheric pressure

Methane coupling in microwave plasma under atmospheric pressure has been investigated.The effects of molar ratio n(CH4)/n(H2),flow rate and microwave power on the reaction have been studied.(1)With the decrease of n(CH4)/n(H2)ratio,methane conversion,C2 hydrocarbon yield,energy yield and space-time yield of acetylene increased,but the yield of carbon deposit decreased.(2)With the increase of microwave power,energy yield of acetylene decreased,but space-time yield of acetylene increased.(3)With the increase of flow rate,energy yield and space-time yield of acetylene increased first and then decreased.Finally,under the reaction conditions of CH4 flow rate of 700 mL/min,n(CH4)/n(H2)ratio of 1/4 and microwave power of 400 W,the energy yield and space-time yield of acetylene could reach 0.337 mmol/kJ and 12.3 mol/(s m3),respectively.The reaction mechanism of methane coupling in microwave plasma has been investigated based on the thermodynamics of chemical reaction.Interestingly,the acetylene yield of methane coupling in microwave plasma was much higher than the maximum thermodynamic yield of acetylene.This phenomenon was tentatively explained from non-expansion work in the microwave plasma system.     

Conversion of Methane to C2 Hydrocarbons via Cold Plasma Reaction

Direct conversion of methane to C2 hydrocarbons via cold plasma reaction with catalysts has been studied at room temperature and atmospheric pressure. Methane can be converted into C2 hydrocarbons in different selectivity depending on the form of the reactor, power of plasma, flow rate of methane, ratio of N2/CH4 and nature of the catalysts. The selectivity to C2 hydrocarbons can reach as high as 98.64%, and the conversion of methane as high as 60% and the yield of C2 hydrocarbons as high as 50% are obtained. Coking can be minimized under the conditions of: proper selection of the catalysts, appropriate high flow rate of inlet methane and suitable ratio of N2 to CH4. The catalyst surface provides active sites for radical recombination.     

Methane formation route in the conversion of methanol to hydrocarbons

The influence factors and paths of methane formation during methanol to hydrocarbons （MTH） reaction were studied experimentally and thermodynamically. The fixed-bed reaction results show that the formation of methane was favored by not only high temperature, but also high feed velocity, low pressure, as well as weak acid sites dominated on deactivated catalyst. The thermodynamic analysis results indicate that methane would be formed via the decomposition reactions of methanol and DME, and the hydrogenolysis reactions of methanol and DME. The decomposition reactions are thermal chemistry processes and easily occurred at high temperature. However, they are influenced by catalyst and reaction conditions through DME intermediate. By contrast, the hydrogenolysis reactions belong to catalytic processes. Parallel experiments suggest that, in real MTH reactions, the hydrogenolysis reactions should be mainly enabled by surface active H atom which might come from hydrogen transfer reactions such as aromatization. But H2 will be involved if the catalyst has active components like NiO.     

有氧气氛下等离子体甲烷偶联反应的研究

近年来,非平衡等离子体应用于甲烷直接转化的研究备受关注,但多数研究工作采用的是低气压下微波或高频放电产生的非平衡等离子体[1－9].在常压下获得非平衡等离子体一般是通过脉冲电晕放电或介质阻挡放电产生的[10,11].Liu等[12]采用电晕放电（非脉冲）研究了CH4＋O2＋He(pCH4=2.03×104Pa,pO2=5.07×103Pa,He平衡)体系的甲烷偶联反应.　　如前文[13]所述,脉冲电晕等离子体是一种新型常压非平衡等离子体,其电子通过上升沿陡峭的窄脉冲电场加速而获得能量（1～20eV）.将其应用于甲烷偶联反应,不仅具有反应条件温和（常温常压）…     

Multi-element selective radio frequency plasma detector for capillary gas chromatography

A radio frequency plasma detector for element specific detection in gas chromatography is described. The detector is comprised of a radio frequency (300 kHz) discharge between electrodes in helium, and utilizes a low-resolution emission spectrometer to monitor selected spectral emission lines produced when the helium discharge decomposes and excites the atomic constituents in the chromatographic column effluent. The spectrometer is tuned to an atomic emission line in the near-infrared portion of the spectrum, and the emission intensity from the discharge region of a selected line is used to monitor the concentration of the element producing that line. Acceptable detector sensitivity was achieved by the use of a high-throughput optical system. Selectivity was achieved by a combination of correct line selection, plasma and carrier gas purification, and plasma gas doping.     

Evaluation of a radio frequency plasma for oxygen-selective detection in capillary gas chromatography

A radio frequency plasma detector for capillary GC has been modified for oxygen-selective detection. Purification of the plasma gas and purging of both ends of the discharge region with helium were crucial to minimizing oxygen background emission from impurities in the plasma. With a pure helium plasma, eluting hydrocarbons released oxygen from the discharge region resulting in interfering signals on the oxygen channel. These interfering signals were efficiently reduced by using a methane-doped (0. 15%) low power RF plasma (15 W) sustained in a high make-up flow (150 mL/min). With this plasma, a 10³:1 oxygen-to-carbon selectivity and a 100 pg oxygen/s detection limit were obtained. The detector was linear over three orders of magnitude. The detection system has been used to screen for oxygenated compounds in two environmental samples.     

脉冲电晕等离子体作用下CH4/H2反应的机理

本文利用发射光谱技术,对脉冲电晕等离子体作用CH4/H2反应进行了原位诊断,根据等离子体作用下CH4、H2和CH4/H2体系中部分激发态物种的光谱检测数据和有关实验的结果,结合等离子体特性及小分子光化学反应规律,对等离子体作用CH4/H2转化制备C2烃反应的机理进行了讨论。     

甲烷在微波等离子体下直接转化成C2烃

研究了非平衡微波等离子体中影响甲烷脱氢转化的几个因素，如功率、ＣＨ４／Ｈ２比和体系压力。在最佳条件下，甲烷转化率和乙炔的选择性分别达到７７．４６％和７４．０４％。     

大气压旋转螺旋状电极辉光放电等离子体催化甲烷偶联

采用新研制的具有旋转螺旋状电极的大气压辉光放电等离子体反应器催化甲烷偶联制碳二烃. 实验采用铜电极和不锈钢电极分别考察了输入电场峰值电压和甲烷、氢气进料流量等参数对甲烷转化率和碳二烃收率、选择性的影响. 在长时间连续反应无明显积碳的情况下, 最佳试验结果是电极材料为金属铜, 进料流量为60 mL•min^-1, V(CH₄ )/V(H₂)=1的条件下, 输入电场峰值电压为2.3 kV时, 甲烷转化率为70.64%, 碳二烃单程收率及其选择性分别为69.85%和 99.14%.     

Platinum- and CuOx-Decorated TiO2 Photocatalyst for Oxidative Coupling of Methane to C2 Hydrocarbons in a Flow Reactor

Oxidative coupling of methane (OCM) is considered one of the most promising catalytic technologies to upgrade methane. However, C₂ products (C₂H₆/C₂H₄) from conventional methane conversion have not been produced commercially owing to competition from overoxidation and carbon accumulation at high temperatures. Herein, we report the codeposition of Pt nanoparticles and CuO_x clusters on TiO₂ (PC-50) and use of the resulting photocatalyst for OCM in a flow reactor operated at room temperature under atmospheric pressure for the first time. The optimized Cu_0.1Pt_0.5/PC-50 sample showed a highest yield of C₂ product of 6.8 μmol h⁻¹ at a space velocity of 2400 h⁻¹, more than twice the sum of the activity of Pt/PC-50 (1.07 μmol h⁻¹) and Cu/PC-50 (1.9 μmol h⁻¹), it might also be the highest among photocatalytic methane conversions reported so far under atmospheric pressure. A high C₂ selectivity of 60 % is also comparable to that attainable by conventional high-temperature (>943 K) thermal catalysis. It is proposed that Pt functions as an electron acceptor to facilitate charge separation, while holes could transfer to CuO_x to avoid deep dehydrogenation and the overoxidation of C₂ products.     

A kinetic study of methane conversion by a dinitrogen microwave plasma

Conversion of CH₄ with a N₂ microwave plasma (2.45 GHz) is studied. The experiments cover the absorbed microwave power range 300–700 W with 17–62% of methane in the gas mixture, with pressures of 10–40 mbar and flow rates of 140–650 ml· min^–1. The yields of C₂ hydrocarbons and dihydrogen are analyzed by gas chromatography. The distance of methane addition downstream of the plasma plays an important role on the composition and the concentration of the products obtained. This distance mainly determines the energy concentrated in the active species of the plasma when they react with methane. Different behaviors for acetylene formation, on the one hand, and for ethane and ethene formation, on the other hand, have been observed, and this finding allows us to propose a kinetic mechanism for the decay of methane and for the formation of C₂ hydrocarbons.     

电场增强催化甲烷合成碳二烃催化剂影响研究

本研究提出了在常温、常压电场增强等离子体条件下甲烷直接转化合成碳二烃的洁净工艺 ,在不同的放电电压、放电功率、甲烷进料流量和不同的催化剂作用下 ,甲烷能够以不同的转化率和选择性转变为碳二烃。对影响甲烷转化率和碳二烃选择性的因素 :放电电压、放电功率、甲烷进料流量和催化剂进行了研究 ,对催化剂性能进行了比较 ,并探讨了反应机理。结果表明 ,适宜的工艺条件 :放电电压 2 0kV～ 4 0kV ;输入功率 :2 0W～ 4 0W ;合适的甲烷进料流量 :30mL/min～ 70mL/min。在该条件下 ,碳二烃的选择性可以达到 95 % ;催化剂对甲烷转化率的影响顺序为MnO2 /Al2 O3 >Ni/Al2 O3 >MoO3 /Al2 O3 >Ni/NaY >Pd/ZSM 5 >Ni/H4Mg2 Si3 O4>Ni/ZSM 5 >Co/ZSM 5 >无催化剂。     

Catalysis Conversion Methane into C2 Hydrocarbons via Electric Field Enhanced Plasma

In this paper the effect of catalyst and carrier in electric field enhanced plasma on methane conversion into C2 hydrocarbons was investigated. Methane coupling reaction was studied in the system of continuous flow reactor on Ni, MoO3, MnO2 catalysts and different ZSM-5 carriers. The per pass conversion of methane can be as high as 22%, the selectivity of ethylene can be as high as 23.8%, of acetylene 60.8%, of ethane 5.4% and of total C2 hydrocarbons was more than 90%. ZSM-5-25 was the better carrier and MnO2 was the better active component. The efficiency of energy was as high as 7.81%.     

常压辉光放电等离子体转化CH4制C2烃的研究

采用新型的旋转电极辉光放电反应器, 在常温常压下对辉光等离子体作用下的甲烷转化制C₂烃进行了研究. 在氢气共存条件下, 考察了反应器电极的结构、材料, 输入电场峰值电压和反应物流率等参数对甲烷转化率和C₂烃单程收率及其选择性的影响规律, 同时比较了不同反应器的能量效率. 结果表明: 在本实验条件下, 金属铜材料好于不锈钢, 螺旋形结构优于三排圆盘结构. CH₄转化率和C₂烃选择性和收率均随输入电场峰值电压的升高而增大, 随反应物流量的增加而减小. 从CH₄转化率、C₂烃的收率和选择性的指标来评价这些反应器, 采用旋转螺旋状铜电极反应器时最好, 当反应物流量为60 mL/min时, 甲烷最高转化率为77.31%, 对应的C₂烃收率和选择性分别为75.66%和97.88%; 当能量密度为800 kJ/mol时, 能效最高为13.5%.     

Non‐Oxidative Methane Conversion Using Lead‐ and Iron‐Modified Albite Catalysts in Fixed‐Bed Reactor

Raw and modified albite catalysts, including Pb/Albite and Fe/Albite catalysts, have been investigated for methane conversion to C₂ hydrocarbons under non‐oxidative conditions. Introduction of Pb to albite improved the activity and selectivity to non‐coke products. Based on characterization, it was found that Pb entered into the alkali and alkaline‐earth metal sites of albite, while partial Fe doped in the tetrahedron sites and the other loaded on the surface of albite. At the reaction temperature of 1073 K, methane gas hourly space velocity (GHSV) of 2 L·gcat^–1·h^–1, catalyst dosage of 0.25 g (300 mesh), the methane conversion catalyzed by raw albite in the fixed‐bed micro reactor exhibited a methane conversion of 3.32%. Notably, introducing a Pb content of 3.4 wt% into albite greatly enhanced the conversion of methane up to 8.19%, and the selectivity of C₂ hydrocarbons reached 99% without any coke under the same reaction conditions. While Fe‐doping could weakly heighten the methane conversion to 3.97%, and coke was formed. Thus, a comparison of Pb/Albite and Fe/Albite catalysts demonstrates that the catalytic activity of albite is mainly decided by alkali and alkaline‐earth metal sites, and lead‐modification can effectively improve the catalytic activity of albite.