Lithium Polystyrene Sulfonate as a Hole Transport Material in Inverted Perovskite Solar Cells

Despite the exceptional efficiency of perovskite solar cells (PSCs), further improvements can be made to bring their power conversion efficiencies (PCE) closer to the Shockley-Queisser limit, while the development of cost-effective strategies to produce high-performance devices are needed for them to reach their potential as a widespread energy source. In this context, there is a need to improve existing charge transport layers (CTLs) or introduce new CTLs. In this contribution, we introduced a new polyelectrolyte (lithium poly(styrene sulfonate (PSS))) (Li:PSS) polyelectrolyte as an HTL in inverted PSCs, where Li⁺ can act as a counter ion for the PSS backbone. The negative charge on the PSS backbone can stabilize the presence of p-type carriers and p-doping at the anode. Simple Li:PSS performed poorly due to poor surface coverage and voids existence in perovskite film as well as low conductivity. PEDOT:PSS was added to increase the conductivity to the simple Li:PSS solution before its use which also resulted in lower performance. Furthermore, a bilayer of PEDOT:PSS and Li:PSS was employed, which outperformed simple PEDOT:PSS due to high quality of perovskite film with large grain size also the large electron injection barrier (ϕ_e) impeded back diffusion of electrons towards anode. As a consequence, devices employing PEDOT:PSS / Li:PSS bilayers gave the highest PCE of 18.64%.     

Highly enhanced thermoelectric performance of WS2 nanosheets upon embedding PEDOT:PSS

Two‐dimensional (2D) WS₂ nanosheets (NSs) as a promising thermoelectric (TE) material have gained great concern recently. The low electrical conductivity significantly limits its further development. Herein, we reported an effective method to enhance the TE performance of WS₂ NSs by combining poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS). The restacked WS₂ NSs thin film with 1T phase structure obtained by a common chemical lithium intercalation show a high Seebeck coefficient of 98 μV K^?1 and a poor electrical conductivity of 12.5 S cm^?1. The introduction of PEDOT:PSS with different contents obviously improve the electrical conductivity of WS₂ NSs thin films. Although a declining Seebeck coefficient was observed, an optimized TE power factor of 45.2 μW m^?1 k^?1 was achieved for WS₂/PEDOT:PSS composite thin film. Moreover, the as‐prepared WS₂/PEDOT:PSS thin film can be easily peeled off and transferred to other substrate leading to a more promising application. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 997–1004     

Why does the electrical conductivity in PEDOT:PSS decrease with PSS content? A study combining thermoelectric measurements with impedance spectroscopy

We have investigated the electrical transport properties of poly(3,4‐ethylenedioxythiophen)/poly(4‐styrene‐sulfonate) (PEDOT:PSS) with PEDOT‐to‐PSS ratios from 1:1 to 1:30. By combining impedance spectroscopy with thermoelectric measurements, we are able to independently determine the variation of electrical conductivity and charge carrier density with PSS content. We find the charge carrier density to be independent of the PSS content. Using a generalized effective media theory, we show that the electrical conductivity in PEDOT:PSS can be understood as percolation between sites of highly conducting PEDOT:PSS complexes with a conductivity of 2.3 (Ωcm)^?1 in a matrix of excess PSS with a low conductivity of 10^?3 (Ω cm)^?1. In addition to the transport properties, the thermoelectric power factors and Seebeck coefficients have been determined. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Photovoltaic performance enhancement using fluorene‐based copolymers containing pyrene units

A set of novel conjugated polyfluorene co‐ polymers, poly[(9,9′‐didecylfluorene‐2,7‐diyl)‐co‐(4,7′‐di‐2‐thienyl‐ 2′,1′,3′‐benzothiadiazole‐5,5‐diyl)‐co‐(pyrene‐1,6‐diyl)], are synthesized via Pd(II)‐mediated polymerization from 2,7‐bis(4′,4′,5′, 5′‐tetramethyl‐1,3,2‐dioxaborolan‐2‐yl)‐9,9′‐di‐n‐decylfluorene, 4, 7‐di(2‐bromothien‐5‐yl)‐2,1,3‐benzothiadiazole, and 1,6‐dibromopyrene with a variety of monomer molar ratios. The field‐effect carrier mobilities and optical, electrochemical, and photovoltaic properties of the copolymers are systematically investigated. The hole mobilities of the copolymers are found to be in the range 7.0 × 10^?5 ? 8.0 × 10^?4 cm² V^?1 s^?1 and the on/off ratios were 8 × 10³ ? 7 × 10⁴. Conventional polymer solar cells (PSCs) with the configuration ITO/PEDOT:PSS/polymer:PC₇₁BM/LiF/Al are fabricated. Under optimized conditions, the polymers display power conversion efficiencies (PCEs) for the PSCs in the range 1.99–3.37% under AM 1.5 illumination (100 mW cm^?2). Among the four copolymers, P2, containing a 2.5 mol % pyrene component incorporated into poly[9,9′‐didecylfluorene‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] (PFDTBT) displays a PCE of 3.37% with a short circuit current of 9.15 mA cm^?2, an open circuit voltage of 0.86 V, and a fill factor of 0.43, under AM 1.5 illumination (100 mW cm^?2). © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Influence of imidazole‐based acidity control of PEDOT:PSS on its electrical properties and environmental stability

Poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) has been studied for a wide range of applications due to its potential as a transparent electrode. Herein, the use of imidazole and its derivatives as a neutralizing additive for PEDOT:PSS dispersion and in‐depth studies of their effects in terms of electrical properties and stability is reported. Although the neutralization in general reduces the electrical conductivity of PEDOT:PSS, the conductivity after imidazole treatment (685.2 S cm^?1) is higher than that after treatment of other derivatives. Spectroscopic and thermoelectric studies show that the de‐doping effect resulted in the conductivity reduction. As a trade‐off of the conductivity reduction, greatly enhanced long‐term stability and noncorrosive characteristics are obtained after neutralization. The change in sheet resistance of imidazole‐treated PEDOT:PSS after 500 h under harsh conditions (85 °C and 85% humidity) is half that of the untreated samples, demonstrating the great enhancement of the stability. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1530–1536     

Aqueous solution-processed NiOx anode buffer layers applicable for polymer solar cells

A green and facile method has been developed for the room temperature and aqueous solution preparation of NiO_x film as anode buffer layers for polymer solar cells (PSCs). The NiO_x buffer layer is prepared simply by spin-coating nickel acetylacetonate precursor-based aqueous solution onto ITO substrate at room temperature in air. UV-ozone post-treatment promotes the formation of dipolar NiOOH species on the film surface, resulting in the anode buffer layer with suitable work function. PSCs have been fabricated with the device structure of ITO/NiO_x/photoactive layer/PFN/Al. The power conversion efficiencies of the PSCs based on PTB7:PC₇₁BM blends (8.43%) and P3HT:PC₇₁BM blends (3.04%) with NiO_x anode buffer layer are comparable to those with the commonly used PEDOT:PSS anode buffer layer. In addition, the devices made with NiO_x buffer layer exhibit much better air stability than those with PEDOT:PSS. These results indicate that the water solution processed NiO_x film at room temperature in air is a promising anode buffer layer for efficient and stable PSCs. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 747–753     

Free‐Standing Conducting Polymer Films for High‐Performance Energy Devices

Thick, uniform, easily processed, highly conductive polymer films are desirable as electrodes for solar cells as well as polymer capacitors. Here, a novel scalable strategy is developed to prepare highly conductive thick poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (HCT‐PEDOT:PSS) films with layered structure that display a conductivity of 1400 S cm^?1 and a low sheet resistance of 0.59 ohm sq^?1. Organic solar cells with laminated HCT‐PEDOT:PSS exhibit a performance comparable to the reference devices with vacuum‐deposited Ag top electrodes. More importantly, the HCT‐PEDOT:PSS film delivers a specific capacitance of 120 F g^?1 at a current density of 0.4 A g^?1. All‐solid‐state flexible symmetric supercapacitors with the HCT‐PEDOT:PSS films display a high volumetric energy density of 6.80 mWh cm^?3 at a power density of 100 mW cm^?3 and 3.15 mWh cm^?3 at a very high power density of 16160 mW cm^?3 that outperforms previous reported solid‐state supercapacitors based on PEDOT materials.     

Paper: An effective substrate for the enhancement of thermoelectric properties in PEDOT:PSS

A novel strategy via paper as an effective substrate has been introduced as a thermoelectric material in this work. Free‐standing poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS)/paper composite films are conveniently prepared by a one‐step method of directly writing PEDOT:PSS solution on paper, making the process simple, rapid, and facile. The free‐standing composite films display excellent flexibility, light weight, soaking stability in water, and great potential in large‐scale production. Improved thermoelectric properties are obtained in PEDOT:PSS/paper composite films, owing to the simultaneously enhanced Seebeck coefficient (30.6 μV K^?1) and electrical conductivity, and a low thermal conductivity (0.16 W m^?1 K^?1) compared with pristine PEDOT:PSS films. The results indicate that paper as an effective substrate is suitable for the preparation of high‐performance and flexible thermoelectric materials. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 737–742     

A new green-to-transmissive polymer with electroactive poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) as an interface layer for achieving high-performance electrochromic device

A new neutral green electrochromic (EC) polymer, namely poly(5,8-bis(2,3-dihydro[3,4-B][1,4]dioxin-5-yl)-2,3-dual(4-(hexadecyloxy) phenyl) quinoxaline) (PBOPEQ) was designed and synthesized. PBOPEQ-poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) film was further prepared by electrochemical polymerization on the PEDOT:PSS modified indium tin oxide (ITO) electrode. Scanning electron microscopy images and ultrasonic experiment indicate that PBOPEQ-PEDOT:PSS film shows better film-forming ability and stronger interface adhesive with ITO electrode compared to that of PBOPEQ film. It is worth mentioning that PBOPEQ-PEDOT:PSS film presents more reversible redox characteristic, better optical contrast (~40%) and coloration efficiency (~230 cm² C⁻¹) at 678 nm, excellent EC stability and memory property (36 hr), which should be ascribed to that the electroactive PEDOT:PSS layer facilitates the charge transfer process and enhances the ion doping/dedoping properties. EC device based on PBOPEQ-PEDOT:PSS film exhibits superior integrated performance such as reversible color change from green to transmissive, optical contrast of 41.0% and switching time less than 1 s. Accordingly, PBOPEQ-PEDOT:PSS is an excellent EC material when combined with electroactive PEDOT:PSS interface layer for achieving high performance device, which shows potential applications in displays, electronic papers, and tags.     

Polymer Optoelectronic Devices with High‐Conductivity Poly(3,4‐Ethylenedioxythiophene) Anodes

Abstract

The conductivity of poly(3,4‐ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) film can be enhanced by more than two orders in magnitude by adding a compound with two or more polar groups, such as ethylene glycol (EG), meso‐erythritol (IUPAC name: 1,2,3,4‐tetrahydroxybutane), or 2‐nitroethanol, into the PEDOT:PSS aqueous solution. The mechanism of the increase in conductivity for PEDOT:PSS has been studied using Raman spectroscopy and atomic force microscope (AFM). Here we propose that the change in conductivity is due to the conformational change of PEDOT chains in the film. In untreated PEDOT:PSS films, coil, linear, or expanded‐coil conformations of the PEDOT chains may be present. In treated PEDOT:PSS films, the linear or expanded‐coil conformations may becomes the dominant form for PEDOT chains. This conformational change results in the enhancement of charge‐carrier mobility in the film and leads to enhanced conductivity. The high‐conductivity PEDOT:PSS film is ideal as the electrode for polymer optoelectronic devices. In this article, we report on the fabrication of polymer light‐emitting diodes (PLEDs) and photovoltaic cells (PVs) made using a highly conductive form of PEDOT:PSS as anode, and we demonstrate its performance relative to that of similar device using indium‐tin oxide (ITO) as the anode.     

Improved photovoltaic performance from high quality perovskite thin film grown with the assistance of PC<Subscript>71</Subscript>BM

The strategy of sequentially spin-coating a perovskite film from the perovskite precursor and an electron transporting layer of [6,6]-phenyl-C₇₁-butyric acid methyl ester (PC₇₁BM) is developed to simplify the fabrication procedure of perovskite solar cells. X-ray diffraction and scanning electron microscopy indicate that PC₇₁BM film on perovskite layer can retard the evaporation of dimethyl sulfoxide (DMSO) efficiently, thus prolonging the transformation of intermediate phase to perovskite crystals, leading to a high quality perovskite thin film. The solar cells with the structure of indium tin oxides (ITO)/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)/CH₃NH₃PbI₃/PC₇₁BM/bathocuproine (BCP)/Ag made from this simplified method exhibit a higher efficiency (12.68%) than those from the conventional one-step method (9.49%).     

New 5-Octyl-thieno[3,4-c]pyrrole-4,6-dione Based Polymers: Synthesis and Photovoltaic Properties

Two donor-acceptor conjugated polymers, namely poly{4,8-bis(5-(2-ethylhexyl) thiophen-2-yl)benzo[1,2-b:4,5-b']difuran-alt-5-octyl-4H-thieno[3,4-c]pyrrole-4,6(5H)-dione}(PBDFTTPD) and poly{4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b: 4,5-b']dithiophene-alt-5-octyl-4H-thieno[3,4-c]pyrrole-4,6(5H)-dione}(PBDTTTPD), were synthesized by Stille coupling polymerization reactions. Their structures were verified by ¹H-NMR and elemental analysis, the molecular weights were determined by gel permeation chromatography and the thermal properties were investigated by thermogravimetric analysis. The polymer films exhibited broad absorption bands. The hole mobility of PBDFTTPD:PC₇₁BM(1:2, w/w) blend reached up to 5.5 × 10^?2 cm² v^?1 s^?1 by the space-charge-current method. Preliminary photovoltaic cells based on the device structure of ITO/PEDOT:PSS/PBDFTTPD:PC₇₁BM(1:2, w/w)/Ca/Al showed a power conversion efficiency of 2.32% with an open-circuit voltage of 0.90 V and a short circuit current of 4.40 mA cm^?2.     

Conductive paper through LbL multilayering with conductive polymer: dominant factors to increase electrical conductivity

A conductive paper was made of cellulose fibers with a multilayer of polyethyleneimine (PEI) and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and the factors to increase the conductivity of the paper were investigated. The adsorption amount and the structure of PEI and PEDOT:PSS multilayer was changed by controlling salt concentration and the number of layers, and inter-contact degree of fibers was controlled by calendering. The adsorption behavior of the polyelectrolytes onto cellulose was evaluated using a quartz crystal microbalance with dissipation monitoring, and the adsorption amount was quantitatively analyzed through Kjeldahl nitrogen analysis and an Inductively Coupled Plasma Optical Emission Spectrometer. The conductivity of the resultant paper was in the range of 10^?5–10^?4 S/cm without loss of paper strength. The conductivity of the paper increased when the multilayer was formed at low salt concentration and the conductive paper was calendered. It appeared that electron transfer by increased contact between PEDOT:PSS improved the conductivity of the paper.     

An Alternative Anionic Polyelectrolyte for Aqueous PEDOT Dispersions: Toward Printable Transparent Electrodes

Organic conducting polymers are promising electrode materials for printable organic electronics. One of the most studied conducting polymers is PEDOT:PSS, which is sufficiently conductive and transparent, but which shows some drawbacks, such as hygroscopicity and acidity. A new approach to stabilize PEDOT in aqueous dispersions involves the replacement of PSS with a basic polyanion based on a polystyrene backbone with (trifluoromethylsulfonyl)imide (TSFI) side groups. The PEDOT:PSTFSIK dispersions were obtained by oxidative polymerization of EDOT in an aqueous PSTFSIK solution and were characterized with regard to their composition, morphology, doping, rheological behavior, and optoelectronic performance. The PEDOT:PSTFSIK dispersions showed excellent printability and good optoelectronic performance (238 Ohm sq^?1 at 91 % transmittance, σ>260 S cm^?1) and were successfully integrated as flexible electrodes in OLED and OPV devices.     

Molecular engineering of conjugated polymers for solar cells and field‐effect transistors: Side‐chain versus main‐chain electron acceptors

Two model polymers, containing fluorene as an electron‐donating moiety and benzothiadiazole (BT) as an electron‐accepting moiety, have been synthesized by Suzuki coupling reaction. Both polymers are composed of the same chemical composition, but the BT acceptor can be either at a side‐chain (i.e., S‐polymer) or along the polymer main chain (i.e., M‐polymer). Their optical, electrochemical, and photovoltaic properties, together with the field‐effect transistor (FET) characteristics, have been investigated experimentally and theoretically. The FET carrier mobilities were estimated to be 5.20 × 10^?5 and 3.12 × 10^?4 cm² V^?1 s^?1 for the S‐polymer and M‐polymer, respectively. Furthermore, polymeric solar cells (PSCs) with the ITO/PEDOT:PSS/S‐polymer or M‐polymer:PC₇₁BM(1:4)/Al structure were constructed and demonstrated to show a power conversion efficiency of 0.82 and 1.24% for the S‐polymer and M‐polymer, respectively. The observed superior device performances for the M‐polymer in both FET and PSCs are attributable to its relatively low band‐gap and close molecular packing for efficient solar light harvesting and charge transport. This study provides important insights into the design of ideal structure–property relationships for conjugate polymers in FETs and PSCs. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Improving the performance of polymer solar cells by efficient optimizing the hole transport layer-graphene oxide

Graphene oxide (GO) materials have emerged as a promising alternative for hole transport layer (HTL) in polymer solar cells (PSCs) due to their unique structures and properties. However, insulating properties and eco-contaminative production of GO still need to be solved. Here, we report on the preparation of GO through an improved Hummers method without using NaNO₃, which is an eco-friendly option because it avoids the emissions of NO₂ and N₂O₄ toxic gases. Subsequently, the GO as HTL in PSCs is reduced by simple heat treatment of different temperatures in air, and the performance of devices is obviously improved. The FT-IR and XPS spectra show oxygenated functional groups in GO thin films are gradually removed with the increase of annealing temperature, which restores sp² hybridized graphitic structure, and makes the GO thin films more conducive to the charge transfer. The highest power conversion efficiency of PSCs based on the P3HT: PC₇₁BM system with GO as HTL is 3.39%, which approaches that of PSCs with PEDOT: PSS as HTL (3.41%). Moreover, the devices with annealed GO as HTL have better stability compared to devices with PEDOT: PSS.     

Highly Conductive PEDOT:PSS Films with 1,3‐Dimethyl‐2‐Imidazolidinone as Transparent Electrodes for Organic Light‐Emitting Diodes

Highly conductive poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films as transparent electrodes for organic light‐emitting diodes (OLEDs) are doped with a new solvent 1,3‐dimethyl‐2‐imidazolidinone (DMI) and are optimized using solvent post‐treatment. The DMI doped PEDOT:PSS films show significantly enhanced conductivities up to 812.1 S cm⁻¹. The sheet resistance of the PEDOT:PSS films doped with DMI is further reduced by various solvent post‐treatment. The effect of solvent post‐treatment on DMI doped PEDOT:PSS films is investigated and is shown to reduce insulating PSS in the conductive films. The solvent posttreated PEDOT:PSS films are successfully employed as transparent electrodes in white OLEDs. It is shown that the efficiency of OLEDs with the optimized DMI doped PEDOT:PSS films is higher than that of reference OLEDs doped with a conventional solvent (ethylene glycol). The results present that the optimized PEDOT:PSS films with the new solvent of DMI can be a promising transparent electrode for low‐cost, efficient ITO‐free white OLEDs.

     

Ti3C2Tx-Modified PEDOT:PSS Hole-Transport Layer for Inverted Perovskite Solar Cells

PEDOT:PSS is a commonly used hole-transport layer (HTL) in inverted perovskite solar cells (PSCs) due to its compatibility with low-temperature solution processing. However, it possesses lower conductivity than other conductive polymers and metal oxides, along with surface defects, limiting its photovoltaic performance. In this study, we introduced two-dimensional Ti₃C₂T_x (MXene) as an additive in the PEDOT:PSS HTL with varying doping concentrations (i.e., 0, 0.03, 0.05, and 0.1 wt.%) to tune the electrical conductivity of PEDOT:PSS and to modify the properties of the perovskite film atop it. We noted that the grain size of the CH₃NH₃PbI₃ (MAPI₃) perovskite layer grown over an optimal concentration of MXene (0.03 wt.%)-doped PEDOT:PSS increased from 250 nm to 400 nm, reducing charge recombination due to fewer grain boundaries. Ultraviolet photoelectron spectroscopy (UPS) revealed increased work function (WF) from 4.43 eV to 4.99 eV with 0.03 wt.% MXene doping, making the extraction of holes easier due to a more favorable energy level alignment with the perovskite. Quantum chemical investigations based on density functional theory (DFT) were conducted at the ωB97XD/6-311++G(d,p) level of theory to provide more insight into the stability, bonding nature, and optoelectronic properties of the PEDOT:PSS–MXene system. The theoretical investigations revealed that the doping of PEDOT:PSS with Ti₃C₂T_x could cause a significant effect on the electronic properties of the HTL, as experimentally demonstrated by an increase in the electrical conductivity. Finally, the inverted PSCs employing 0.03 wt.% MXene-doped PEDOT:PSS showed an average power conversion efficiency (PCE) of 15.1%, up from 12.5% for a reference PSC employing a pristine PEDOT:PSS HTL. The champion device with a 0.03 wt.% MXene–PEDOT:PSS HTL achieved 15.5% PCE.     

Scientific Importance of Water‐Processable PEDOT–PSS and Preparation,Challenge and New Application in Sensors of Its Film Electrode: A Review

In this review, PEDOT–PSS is mainly a commercially available PEDOT–PSS, which is a water‐dispersible form of the intrinsically conducting PEDOT doped with the water‐soluble PSS, including its derivatives, copolymers, analogs (PEDOT:PSSs), even their composites via the chemical or physical modification toward the structure of PEDOT and/or PSS. First, we will focus on discussing the scientific importance of PEDOT–PSS in conjunction with its extraordinary properties and broad multidisciplinary applications in organic/polymeric electronics and optoelectronics from the viewpoint of the historical development and the promising application of representative ECPs. Subsequently, versatile film‐forming techniques for the preparation of PEDOT–PSS film electrode were described in details, including common coating approaches and printing techniques, and many emerging preparative methods were mentioned. Then challenges (e.g., conductivity, stability in Water, adhesion to substrate electrode) of PEDOT–PSS film electrode for devices under the high humidity/watery circumstances, especially electrochemical devices are discussed. Fourth, we take PEDOT–PSS film electrode for a relatively new application in sensors as an example, mainly summarized advances in the development of various sensors based on PEDOT–PSSs and their composites in combination with its preparative methods and extraordinary properties. Finally, we give the outlook of PEDOT–PSS for possible applications with the emphasis on PEDOT–PSS film electrode for electrochemical devices, including sensors. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 55, 1121–1150     

Electrochemiluminescence Biosensor Based on PEDOT‐PSS‐ Graphene Functionalized ITO Electrode

A novel and sensitive electrochemiluminescence (ECL) method for ethanol biosensor was developed by co‐immobilizing the enzyme and ECL reagent Ru(bpy)₃²⁺ on the poly‐(3,4‐ethylene dioxythiophene) and polystyrene sulfonate functionalized graphene (PEDOT‐PSS‐G) nanocomposite film. Positively charged Ru(bpy)₃²⁺ could be immobilized effectively on the electrode surface with the negatively charged PSS and graphene, which provided a stable ECL platform for further modification with the enzyme. Moreover, the introduction of PEDOT and graphene can be acted as a conducting pathway to accelerate the electron transfer due to the high conductivity. Such biosensor combined enzymatic selectivity with the amplification of PEDOT‐PSS‐G performed well with a wide linear range, high sensitivity and good stability. The sensing platform was successfully applied to determine the amounts of alcohol in real samples.