A dielectric crack in a functionally graded piezoelectric layer

Considering the dielectric effects inside a crack, the problem of an electrically dielectric crack in a functionally graded piezoelectric layer is addressed in this paper. The energetically consistent crack-face boundary conditions are utilized to analyze the effects of a dielectric of crack interior. Applying the Fourier transform technique, the boundary-value problem is reduced to solving three coupling singular equations. Then a system of non-linear algebraic equations is obtained and the field intensity factors along with the energy release rate are given. Numerical results show the differences of the electric displacement inside a crack, the stress and electric displacement intensity factors and the energy release rate using the permeable, impermeable, semi-permeable and energetically consistent boundary conditions respectively. The effects of the material non-homogeneity, the applied electric field and the discharge field of crack interior on the electrostatic traction acting on the crack faces and the energy release rate are further studied through the energetically consistent boundary conditions.     

Transient response of a magnetoelectroelastic solid with two collinear dielectric cracks under impacts

Dynamic analysis of two collinear electro-magnetically dielectric cracks in a piezoelectromagnetic material is made under in-plane magneto-electro-mechanical impacts. Generalized semi-permeable crack-face boundary conditions are proposed to simulate realistic opening cracks with dielectric. Ideal boundary conditions of a combination of electrically permeable or impermeable and magnetically permeable or impermeable assumptions are several limiting cases of the semi-permeable dielectric crack. Utilizing the Laplace and Fourier transforms, the mixed initial-boundary-value problem is reduced to solving singular integral equations with Cauchy kernel. Dynamic intensity factors of stress, electric displacement, magnetic induction and crack opening displacement (COD) near the inner and outer crack tips are determined in the Laplace transform domain. Numerical results for a special magnetoelectroelastic solid are calculated to show the influences of the dielectric permittivity and magnetic permeability inside the cracks on the crack-face electric displacement and magnetic induction. By means of a numerical inversion of the Laplace transform, the variations of the normalized intensity factors of stress and COD are discussed against applied magnetoelectric impact loadings and the geometry of the cracks for fully impermeable, vacuum, fully permeable cracks and shown in graphics.     

Dynamic analysis of a penny-shaped dielectric crack in a magnetoelectroelastic solid under impacts

The transient response of a magneto-electro-elastic material with a penny-shaped dielectric crack subjected to in-plane magneto-electro-mechanical impacts is made. To simulate an opening crack with a dielectric interior, the crack-face electromagnetic boundary conditions are supposed to depend on the crack opening displacement and the jumps of electric and magnetic potentials across the crack. Four ideal crack-face electromagnetic boundary conditions involving a combination of electrically permeable or impermeable and magnetically permeable or impermeable assumptions can be reduced. The Laplace and Hankel transform techniques are further utilized to solve the mixed initial-boundary-value problem. Three coupling Fredholm integral equations are obtained and solved by the composite Simpson's rule. Dynamic field intensity factors of stress, electric displacement, magnetic induction, crack opening displacement (COD), electric potential and magnetic potential are given in the Laplace transform domain. By means of a numerical inversion of the Laplace transform, numerical results are calculated to show the variations of the physical parameters of concern versus the normalized time in graphics. The effects of applied electric and magnetic loads on the dynamic intensity factors of stress and COD, and the dynamic energy release rate for a BaTiO₃-CoFe₂O₄ composite with a penny-shaped vacuum crack are discussed in detail.     

ANTI-PLANE FRACTURE ANALYSIS OF FUNCTIONALLY GRADIENT MATERIAL INFINITE STRIP WITH FINITE WIDTH

The special case of a crack under mode III conditions was treated, lying parallel to the edges of an infinite strip with finite width and with the shear modulus varying exponentially perpendicular to the edges. By using Fourier transforms the problem was formulated in terms of a singular integral equation. It was numerically solved by representing the unknown dislocation density by a truncated series of Chebyshev polynomials leading to a linear system of equations. The stress intensity factor (SIF) results were discussed with respect to the influences of different geometric parameters and the strength of the non-homogeneity. It was indicated that the SIF increases with the increase of the crack length and decreases with the increase of the rigidity of the material in the vicinity of crack. The SIF of narrow strip is very sensitive to the change of the non-homogeneity parameter and its variation is complicated. With the increase of the non-homogeneity parameter, the stress intensity factor may increase, decrease or keep constant, which is mainly determined by the strip width and the relative crack location. If the crack is located at the midline of the strip or if the strip is wide, the stress intensity factor is not sensitive to the material non-homogeneity parameter.     

Antiplane internal crack normal to the edge of a functionally graded piezoelectric/piezomagnetic half plane

This paper deals with the antiplane magnetoelectroelastic problem of an internal crack normal to the edge of a functionally graded piezoelectric/piezomagnetic half plane. The properties of the material such as elastic modulus, piezoelectric constant, dielectric constant, piezomagnetic coefficient, magnetoelectric coefficient and magnetic permeability are assumed in exponential forms and vary along the crack direction. Fourier transforms are used to reduce the impermeable and permeable crack problems to a system of singular integral equations, which is solved numerically by using the Gauss-Chebyshev integration technique. The stress, electric displacement and magnetic induction intensity factors at the crack tips are determined numerically. The energy density theory is applied to study the effects of nonhomogeneous material parameter β, edge conditions, location of the crack and load ratios on the fracture behavior of the internal crack.     

MULTIPLE PARALLEL SYMMETRIC PERMEABLE MODEL-Ⅲ CRACKS IN A PIEZOELECTRIC/PIEZOMAGNETIC COMPOSITE MATERIAL PLANE

In this paper, the interactions of multiple parallel symmetric and permeable finite length cracks in a piezoelectric/piezomagnetic material plane subjected to anti-plane shear stress loading are studied by the Schmidt method.The problem is formulated through Fourier transform into dual integral equations, in which the unknown variables are the displacement jumps across the crack surfaces.To solve the dual integral equations, the displacement jumps across the crack surfaces are directly expanded as a series of Jacobi polynomials.Finally, the relation between the electric field, the magnetic flux field and the stress field near the crack tips is obtained.The results show that the stress, the electric displacement and the magnetic flux intensity factors at the crack tips depend on the length and spacing of the cracks.It is also revealed that the crack shielding effect presents in piezoelectric/piezomagnetic materials.     

THE BASIC SOLUTION OF A 3-D RECTANGULAR PERMEABLE CRACK IN A PIEZOELECTRIC/PIEZOMAGNETIC COMPOSITE MATERIAL

The solution of a 3-D rectangular permeable crack in a piezoelectric/piezomagnetic composite material was investigated by using the generalized Almansi’s theorem and the Schmidt method.The problem was formulated through Fourier transform into three pairs of dual integral equations,in which the unknown variables are the displacement jumps across the crack surfaces.To solve the dual integral equations,the displacement jumps across the crack surfaces were directly expanded as a series of Jacobi polynomials.Finally,the relations between the electric filed,the magnetic flux field and the stress field near the crack edges were obtained and the efects of the shape of the rectangular crack on the stress,the electric displacement and magnetic flux intensity factors in a piezoelectric/piezomagnetic composite material were analyzed.     

Effects of electric field on crack growth for a penny-shaped dielectric crack in a piezoelectric layer

The assumptions of impermeable and permeable cracks give rise to significant errors in determining electro-elastic behavior of a cracked piezoelectric material. The former simply imposes that the permittivity or electric displacement of the crack interior vanishes, and the latter neglects also the effects of the dielectric of an opening crack interior. Considering the presence of the dielectric of an opening crack interior and the permeability of the crack surfaces for electric field, this paper analyzes electro-elastic behavior induced by a penny-shaped dielectric crack in a piezoelectric ceramic layer. In the cases of prescribed displacement or prescribed stress at the layer surfaces, the Hankel transform technique is employed to reduce the problem to Fredholm integral equations with a parameter dependent nonlinearly on the unknown functions. For an infinite piezoelectric space, a closed-form solution can be derived explicitly, while for a piezoelectric layer, an iterative technique is suggested to solve the resulting nonlinear equations. Field intensity factors are obtained in terms of the solution of the equations. Numerical results of the crack opening displacement intensity factors are presented for a cracked PZT-5H layer and the effect of applied electric field on crack growth are examined for both cases. The results indicate that the fracture toughness of a piezoelectric ceramic is affected by the direction of applied electric fields, dependent on the elastic boundary conditions.     

A finite crack in a semi-infinite strip of a graded piezoelectric material under electric loading

In this paper, the mixed-mode crack problem for a functionally graded piezoelectric material (FGPM) strip is considered. It is assumed that the electroelastic properties of the strip vary continuously along the thickness of the strip, and that the strip is under in-plane electric loading. The problem is formulated in terms of a system of singular integral equations. The stress and electric displacement intensity factors are presented for various values of dimensionless parameters representing the crack size, the crack location, and the material nonhomogeneity.     

层状磁电复合材料界面共线裂纹平面问题分析

本文研究了面内电磁势载荷作用下双层压电压磁复合材料中共线界面裂纹问题．考虑了压电材料的导磁性质和压磁材料的介电性质,引入了界面电位移和磁感强度的连续性条件．利用Fourier 变换得到一组第二类Cauchy 型奇异积分方程．进一步导出了相应问题的应力强度因子、电位移强度因子和磁感强度强度因子的表达式,给出了应力强度因子的数值结果．结果表明电磁载荷会导致界面裂纹尖端I、II 混合型应力奇异性,同时还伴随着电位移和磁感强度的奇异性．比较了双裂纹左右端的应力强度因子,发现在面内极化方向上施加面内磁势载荷时共线裂纹内侧尖端区域的两个法向应力场发生互相干涉增强．     

Transient response of a cracked piezoelectric strip under arbitrary electro-mechanical impact

By using the well-developed integral transform methodology, the dynamic response of stress and electric displacement around a finite crack in an infinite piezoelectric strip are investigated under arbitrary dynamic anti-plane loads. The dynamic stress intensity factors and electric displacement are obtained analytically. It is shown that the dynamic crack-tip stress and electric field still have a square-root singularity. Numerical computations for the dynamic stress intensity factor show that the electric load has a significant influence on the dynamic response of stress field. The higher the ratio of the crack length to the width of the strip, the higher the peak value of the dynamic stress intensity factor is. On the other hand, the dynamic response of the electric field is determined solely by the applied electric load. The electric field will promote or retard the propagation of the crack depending on the time elapse since the application of the external electro-mechanical loads. The project supported by the National Natural Science Foundation of China and the Post-Doctor Science Foundation of China     

Functionally graded piezoelectric strip with a penny-shaped crack under electromechanical loadings

In this paper, the mixed-mode penny-shaped crack problem for a functionally graded piezoelectric material (FGPM) strip is considered. It is assumed that the electroelastic properties of the strip vary continuously along the thickness of the strip, and that the strip is under in-plane electromechanical loadings. The problem is formulated in terms of a system of singular integral equations. The stress and electric displacement intensity factors are presented for various values of dimensionless parameters representing the crack size, the crack location, and the material nonhomogeneity.     

Dynamic behavior of two collinear interface cracks between two dissimilar functionally graded piezoelectric/piezomagnetic material strips

The dynamic interaction of two collinear interface cracks between two dissimilar functionally graded piezoelectric/piezomagnetic material strips subjected to the anti-plane shear harmonic stress waves was investigated. By using the Fourier transform, the problem can be solved with the help of a pair of triple integral equations in which the unknown variable is jump of displacement across the crack surfaces. These equations are solved using the Schmidt method. Numerical examples are provided to show the effect of the functionally graded parameter, the circular frequency of the incident waves and the thickness of the strip upon stress, electric displacement and magnetic flux intensity factors of cracks.     

Anti-plane fracture analysis for the weak-discontinuous interface in a non-homogeneous piezoelectric bi-material structure

The concept of weak discontinuity is extended to functionally graded piezoelectric bi-material interface, and fracture analysis for the weak discontinuous interface is performed by the methods of Fourier integral transform and Cauchy singular integral equation. Numerical results of the total energy release rate (TERR) and the mechanical strain energy release rate (MSERR) are obtained to show the effects of non-homogeneity parameters, geometrical parameters and loads. Parametric studies yield three conclusions: (1) To reduce the weak-discontinuity of the interface is beneficial to resisting interfacial fracture. The effect of the weak-discontinuity of the interface on TERR and MSERR still depends on the strip width. The wider the strip, the more sensitive the TERR and MSERR will be to the weak-discontinuity of the interface. (2) To predict the effect of electric load on crack propagation, MSERR is more appropriate than TERR to be used as a fracture parameter. To predict the effect of mechanical load on crack propagation, both of them could be used as fracture parameters, and MSERR is more conservative. (3) Mechanical load and negative electric displacement load would promote crack propagation, but positive electric displacement load would retard it. For the structure applied by combined mechanical and positive electric displacement loads, crack propagation may be impeded by appropriately selecting the strip width and the ratio of non-homogeneity parameters.     

Electromechanical impact of an impermeable parallel crack in a functionally graded piezoelectric strip

The dynamic fracture problem for a functionally graded piezoelectric material (FGPM) strip containing a crack parallel to the free boundaries is considered in this study. It is assumed that the electroelastic properties of the strip vary continuously along the thickness direction of the strip, and that the strip is under the in-plane mechanical and electric impact. Integral transform techniques and dislocation density functions are employed to reduce the problem to the solutions of a system of singular integral equations. The dynamic stress and electric displacement intensity factors versus time are presented for various values of dimensionless parameters representing the crack size, the crack location, the material nonhomogeneity and the loading combination.     

功能梯度压电板条中电绝缘型运动裂纹的电弹性场

基于三维弹性理论和压电理论，对材料系数按指数函数规律分布的功能梯度压电板条中的反平面运动裂纹问题进行了求解。利用Fourier积分变换方法将电绝缘型运动裂纹问题化为对偶积分方程，并进一步归结为易于求解的第二类Fredholm积分方程。通过渐近分析，获得了裂纹尖端应力、应变、电位移和电场的解析解，给出了裂纹尖端场各个变量的角分布函数，并求得了裂纹尖端场的强度因子，分析了压电材料物性梯度参数、几何尺寸及裂纹运动速度对它们的影响。结果表明，对于电绝缘型裂纹，功能梯度压电板条中运动裂纹尖端附近的各个场变量都具有-1／2阶的奇异性；当裂纹运动速度增大时，裂纹扩展的方向会偏离裂纹面。     

Strip electric-magnetic breakdown model in a magnetoelectroelastic medium

Extending the polarization saturation model [Gao et al., 1997. Local and global energy release rates for an electrically yielded crack in a piezoelectric ceramic. J. Mech. Phys. Solids 45, 491-510] and the dielectric breakdown (DB) model [Zhang et al., 2005. The strip dielectric breakdown model. Int. J. Fract. 132, 311-327] in piezoelectric materials, the Strip Electric-Magnetic Breakdown (SEMB) model is proposed for electrically and magnetically impermeable crack in a magnetoelectroelastic medium to study the effect of the nonlinear character of electric field and magnetic field on fracture of magnetoelectroelastic materials. In the SEMB model, the electric field in the strip of the electric breakdown zone ahead of the crack tip is equal to the electric breakdown strength, while the magnetic filed in the strip of the magnetic breakdown zone is equal to the magnetic breakdown strength. By using the extended Stroh formalism and the extended dislocation modeling of a crack, the Griffith crack problem under the electrically and magnetically elastic-plastic condition in a magnetoelectroelastic medium is reduced to a set of dual integral equations. The sizes of the electric breakdown zone and the magnetic breakdown zone, the extended intensity factors and the local J-integral are obtained. The effect of the combined mechanical-electric-magnetic loadings on the local J-integral is studied.     

SCATTERING OF HARMONIC ANTI-PLANE SHEAR STRESS WAVES BY A CRACK IN FUNCTIONALLY GRADED PIEZOELECTRIC/PIEZOMAGNETIC MATERIALS

In this paper, the dynamic behavior of a permeable crack in functionally graded piezoelectric/piezomagnetic materials is investigated. To make the analysis tractable, it is assumed that the material properties vary exponentially with the coordinate parallel to the crack. By using the Fourier transform, the problem can be solved with the help of a pair of dual integral equations in which the unknown is the jump of displacements across the crack surfaces. These equations are solved to obtain the relations between the electric filed, the magnetic flux field and the dynamic stress field near the crack tips using the Schmidt method. Numerical examples are provided to show the effect of the functionally graded parameter and the circular frequency of the incident waves upon the stress, the electric displacement and the magnetic flux intensity factors of the crack.     

Dynamic analysis of a cracked magnetoelectroelastic medium under antiplane mechanical and inplane electric and magnetic impacts

The transient analysis of a magnetoelectroelastic medium containing a crack is made under antiplane mechanical and inplane electric and magnetic impacts. The crack is assumed to penetrate through the solid along the poling direction. By using the Fourier and Laplace transforms, the associated mixed boundary value problem is reduced to a Fredholm integral equation of the second kind, which is solved numerically. By means of a numerical inversion of the Laplace transform, dynamic field intensity factors are obtained in the time domain. Numerical results are presented graphically to show the effects of the material properties and applied electric and magnetic impacts on the dynamic intensity factors of COD and stress, and dynamic energy density factors. The results indicate that except for the intensity factors of electric displacement and magnetic induction, other field intensity factors exhibit apparent transient feature. Moreover, they depend strongly on mechanical input as well as electric and magnetic impacts.     

Study of a propagating finite crack in functionally graded piezoelectric materials considering dielectric medium effect

This paper provides a study of the problem of a propagating finite crack under in-plane loading in functionally graded piezoelectric materials (FGPMs). The analytical formulations are developed by Fourier transforms and the resulting singular integral equations are solved by using Chebyshev polynomials. By using a dielectric crack model with deformation-dependent electric boundary condition, numerical simulations are made to show the effects of the dielectric medium, the gradient of material properties and the speed of crack propagation on the fracture parameters, such as the stress, electric displacement and crack opening displacement intensity factors. A critical state for the electromechanical loading applied to the FGPMs is observed, which determines whether the traditionally impermeable (or permeable) crack model serves as the upper or lower bound for the dielectric model. The validity of this dielectric crack model is also examined by comparing the results of different existing crack models.