Ni/Al2O3催化剂上甲烷部分氧化制合成气反应CO2主要来源

负载型金属催化剂上甲烷催化部分氧化制合成气反应机理存在着燃烧重整机理和直接氧化机理之争.如果反应按燃烧重整机理进行,则CO     

流化床反应器中Ni/γ-Al2O3催化剂上甲烷部分氧化制合成气

催化甲烷部分氧化(POM)制合成气已成为替代水蒸气重整最有希望的工艺过程之一[1]. 该过程是个温和的放热反应,反应速度非常快,在高空速下可实现高甲烷转化,并且制得的合成气V(H2)/V(CO)=2, 可直接用于合成甲醇及F-T合成烃类、合成二甲醚等后续工业过程. 到目前为止,大部分POM的研究工作在固定床反应器中进行[2～4]. 由于反应速度极快,导致催化剂表面存在热点[2,5], 不仅影响实验的准确性[6,7], 而且工业应用困难. 热点的存在还会导致活性组分Ni的烧结和流失. 在固定床反应器中,催化剂积炭也是导致其活性下降的重要原因[8,9]. Bharadwaj等[10]发现,流化床反应器Rh和Ni催化剂上甲烷转化率高达90%, 反应后催化剂未发现积炭. Santos等[11]曾报道采用流化床催化剂床层几乎可以实现等温分布,而且甲烷转化率接近热力学平衡值, 反应10 h后催化剂表面积炭量仅为0.6%. 本文采用流化床反应器考察了不同反应条件下Ni/γ-Al2O3催化剂上甲烷部分氧化的反应性能,同时对催化剂积炭及稳定性作了初步研究.     

用晶格氧为氧源的甲烷部分氧化制合成气

 采用热重分析技术在甲烷气氛下考察了储氧材料Fe2O3提供晶格氧的过程，用甲烷／氧切换反应和在线质谱检测方法研究了以Fe2O3晶格氧代替气相氧用于甲烷部分氧化制合成气的可能性．结果表明，Fe2O3在甲烷气氛下的还原过程包括Fe2O3→Fe3O4和Fe3O4→FeO→Fe，甲烷被氧化为CO2和H2O．在750℃下进行的CH4／O2切换反应结果表明，首先，约25％的CH4与Fe2O3中的晶格氧反应，生成CO2和H2O，然后，生成的CO2和H2O与剩余的约75％的CH4在Ni／Al2O3催化剂上进行蒸汽重整和C\r\nO2重整，从而按燃烧－重整机理实现甲烷部分氧化制合成气．选择合适的CH4／O2切换条件，可使甲烷高转化率、高选择性地生成合成气．     

Ni/CaO-SiO2对流化床反应器中甲烷转化制合成气的催化性能

用浸渍法制备了Ni／SiO2和Ni／CaO—SiO2催化剂．研究了流化床反应器中用CaO改性微球硅胶载体对催化性能的影响,考察了Ni／CaO—SiO2催化剂上甲烷部分氧化与甲烷二氧化碳重整耦合制合成气反应中Ca负载量、反应温度、空速和原料气中的O2／CO2比对活性与选择性以及产物H2／CO比的影响。并用XRD、TEM、H2-TPR和CO2-TPD等测试手段对催化剂进行了表征。结果表明,经过氧化钙改性的微球硅胶能够将“自由态”的镍物种转变为“束缚态”。使镍物种达到高度分散状态。引入10(wt)％Ca助剂所制备的催化剂具有很好的活性和稳定性,因而具有较好的工业应用前景。     

Ni基催化剂上甲烷与空气或O_2/水蒸气部分氧化制合成气(英文)

在固定床反应器中考察了Ni基催化剂上甲烷氧化与空气或O2/水蒸气部分氧化制合成气的反应。用空气取代纯氧同样能获得高甲烷转化率和产物选择性。水的添加主要发生水气变换反应,同时也能降低催化剂上积炭。在甲烷与纯氧500小时反应的稳定性考察中,甲烷转化率、CO及H2选择性分别保持在90％、95％和95％以上;反应后上层催化剂的Ni含量从新鲜催化剂的7.2％下降到5.2％,在反应后的催化剂上没有发现积炭和相变。     

甲烷在Ni/TiO2催化剂表面的活化

考察了Ni/TiO2催化剂甲烷部分氧化和二氧化碳重整制合成气的反应活性,实验表明,以TiO2为载体的镍系催化剂对于甲烷部分氧化制合成气反应具有较好的活性,尤其对H2的选择性较高,对二氧化碳重整制合成气反应具有较好的低温反应活性.采用脉冲-质谱在线分析等技术,在无气相氧条件下向Ni/TiO2催化剂脉冲CH4,发现甲烷在催化剂表面的活化（转化）及其氧化产物的选择性与金属催化剂表面氧的浓度密切相关.CH4与Ni/TiO2催化剂作用过程中存在明显的氢溢流和氧溢流现象,可能是这种溢流效应使得Ni/TiO2催化剂具有良好的反应活性和抗积碳性能.     

Ni/Al2O3催化剂上甲烷三重整制合成气

制备了负载于大孔容、高比表面的γ-Al2O3载体上的Ni基催化剂.采用固定床流动反应装置,考察了催化剂焙烧温度、反应条件(反应温度、压力、空速以及反应原料气组成)对甲烷三重整反应(TRM)制合成气的催化性能的影响.结果表明,650℃焙烧的催化剂具有较好的稳定性.在常压、850℃、10080h-1、n(CH4)/n(CO2)/n(H2O)/n(O2)=1/0.48/0.54/0.1的条件下,CH4转化率达到95.4%,CO2转化率达到84.6%,在此条件下连续运行9h未见活性下降.TRM反应适宜于在高温、低压下进行,原料组成的变化不会影响CH4转化率,但会影响CO2转化率和产物合成气的n(H2)/n(CO)比.     

NiO/La2O3催化剂上甲烷催化部分氧化制合成气的研究

采用浸渍法制备了一系列不同N i含量的N iO/La2O3催化剂,并利用XRD、BET对催化剂结构进行了表征,采用常压下固定床石英管反应器考察了催化剂对甲烷部分氧化制合成气的反应性能和催化剂的稳定性,其甲烷转化率与反应温度、N i含量以及空速有关.结果表明,N i含量为30%的N iO/La2O3催化剂具有良好的催化活性,800℃时甲烷的转化率为88%,CO选择性可达83%,100 h的连续测试显示N iO/La2O3具有良好的稳定性.     

Rh/SiO_2催化剂上甲烷部分氧化制合成气的反应机理

采用原位Raman光谱技术,在原料气中的O2未完全耗尽的条件下,对CH4部分氧化制合成气反应的Rh/SiO2催化剂床层前部贵金属物种的化学态以及由CH4解离所生成的碳物种进行了表征.在此基础上采用脉冲反应和同位素示踪技术,比较了CH4的部分氧化及其与H2O和CO2的重整等反应对催化剂床层氧化区内CO和H2生成的相对贡献,并将实验结果与Ra-man光谱表征结果进行了关联.结果表明,在600°C下将还原后的4%Rh/SiO2催化剂切入CH4:O2:Ar=2:1:45原料气,催化剂床层前部未检测到铑氧化物的Raman谱峰,但可清晰检测到源于CH4解离的碳物种;在700°C和接触时间小于1ms的条件下,催化剂床层的氧化区内已有大量CO和H2生成,在相同的实验条件下,CH4与H2O或CO2重整反应对氧化区内合成气生成的贡献则很小;以CH4:16O2:H218O:He=2:1:2:95为原料气的同位素示踪实验结果表明,在原料气中16O2未完全耗尽的情况下,反应产物中C16O的含量占CO生成总量的92.3%,表明CO主要来自CH4的部分氧化反应.上述结果均表明,在O2存在下Rh/SiO2催化剂上CO和H2可以通过CH4直接解离和部分氧化机理生成.     

抗积炭CH_4/CO_2重整用Ni/Al_2O_3催化剂

甲烷转化制备的合成气是合成液体燃料和含氧有机化合物的原料 .甲烷转化制合成气的方法有甲烷蒸汽重整、甲烷部分氧化和甲烷、二氧化碳重整 3种 [1～ 3] .对于 CH4/CO2 重整反应 ,调节进料比可制备出 H2 /CO≤ 1、富含 CO的合成气 ,它适于羰基合成和 F- T合成 .这种方法一方面充分利用碳资源 ,缓解能源危机 ;一方面可减少温室气体的排放 ,改善人类的居住环境 .目前倍受关注 .CH4/CO2 重整制合成气 ,Rh、Ru、Pd、Ir等贵金属有很高的活性和稳定性 [4] .但其价格昂贵 ,高温易流失 ,商业化困难 .Ni基催化剂的活性与贵金属相当 ,但它易积…     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.