Design and analysis of a novel single-mode single-polarization photonic crystal fibre based on polarization-dependent coupling and absorption effect

A novel single-mode single-polarization (SMSP) photonic crystal fibre has been proposed and analysed based on the polarization-dependent coupling and absorption effect via a full-vector finite element method with perfectly matched layers. The numerical results predict that very efficient SMSP operation can be achieved with both high bandwidth and high extinction ratio at low loss penalty. Effects of the fibre structural parameters on the SMSP bandwidth and extinction ratio have been explored, which will provide useful guide for the design and fabrication of the fibre. The results obtained will be instructive for the realization of new SMSP fibres with high performance.     

Equilateral pentagon polarization maintaining photonic crystal fibre with low nonlinearity

A new pentagon polarization maintaining photonic crystal fibre with low nonlinearity is introduced. The full vector finite element method was used to investigate the distribution and the effective area of modal field, the nonlinear properties, the effective indices of two orthogonal polarization modes and the birefringence of the new PM-PCF effectively. It is found that the birefringence of the new polarization maintaining photonic crystal fibre can easily achieve the order of 10^-4, and it can obtain higher birefringence, larger effectively mode-field area and lower nonlinearity than traditional hexagonal polarization maintaining photonic crystal fibre with the same hole pitch, same hole diameter, and same ring number. It is important for sensing and communication applications, especially has potential application for fibre optical gyroscope.     

Broad and ultra-flattened supercontinuum generation in the visible wavelengths based on the fundamental mode of photonic crystal fibre with central holes

By coupling a train of femtosecond pulses with 100 fs pulse width at a repetition rate of 76 MHz generated by a mode-locked Ti:sapphire laser into the fundamental mode of photonic crystal fibre(PCF) with central holes fabricated through extracting air from the central hole,the broad and ultra-flattened supercontinuum(SC) in the visible wavelengths is generated.When the fundamental mode experiences an anomalous dispersion regime,three phases in the SC generation process are primarily presented.The SC generation(SCG) in the wavelength range from 470 nm to 805 nm does not emerge significant ripples due to a higher pump peak power and the corresponding mode fields at different wavelengths are observed using Bragg gratings.The relative intensity fluctuations of output spectrum in the wavelength ranges of 530 nm to 640 nm and 543 nm to 590 nm are only 0.028 and 0.0071,respectively.     

Temperature dependence of birefringence in olarization-maintaining photonic crystal fibres

In this paper,the temperature dependence of birefringence in polarization maintaining photonic crystal fibres(PMPCFs) is investigated theoretically and experimentally.Utilizing the structural parameters of the PM-PCF samples in the experiment,two effects leading to the birefringence variation under different temperatures are analysed,which are the thermal expansion of silica material and the refractive index variation due to the temperature variation.The actual birefringence variation of the PM-PCF is the combination of the two effects,which is in the order of 10-9 K-1 for both fibre samples.Calculation results also show that the influence of refractive index variation is the dominant contribution,which determines the tendency of the fibre birefringence variation with varying temperature.Then,the birefringence beat lengths of the two fibre samples are measured under the temperature,which varies from -40℃ to 80℃.A traditional PANDA-type polarization maintaining fibre(PMF) is also measured in the same way for comparison.The experimental results indicate that the birefringence variation of the PM-PCF due to temperature variation is far smaller than that of the traditional PMF,which agrees with the theoretical analysis.The ultra-low temperature dependence of the birefringence in the PM-PCF has great potential applications in temperature-insensitive fibre interferometers,fibre sensors,and fibre gyroscopes.     

用阶跃有效折射率模型研究光子晶体光纤色散特性

在采用阶跃有效折射率模型研究光子晶体光纤的可行性方面，提出了将普通单模光纤、色散位移光纤、色散平坦光纤作为一定极限条件下的折射率引导型光子晶体光纤特例的观点.通过编程计算，并与文献报道的实验数据对比，表明应用本模型可以揭示光子晶体光纤所具有的奇异的色散机理.特别是应用本模型具有更快的计算速度.还用本模型分析了空气孔直径、周期及芯径对色散特性的影响. 关键词： 折射率引导型光子晶体光纤 阶跃有效折射率模型 色散     

Analysis of the special hollow-core photonic crystal fibre by finite element method

Two kinds of fabricated hollow-core photonic crystal fibres （HC-PCFs） arc studied using finite element method （FEM） because the structures of the fibres are special, Normalized transmission spectra and transverse intensity distribution of the modes are calculated and measured. And the dispersion characteristics of these two kinds of HC- PCFs were analysed from 400 nm to 800 nm. Simulated and measured results show that the special structure could affect the properties of HC-PCFs, By comparing the simulated values with the measured results, it can be clarified that FEM is feasible and accurate for analysing photonic crystal fibres whose structures are irregular and complex.     

一种新型的基于四孔单元光子晶体光纤的设计与分析

设计了一种基于四孔单元的光子晶体光纤,它可以满足光通信系统中高双折射率、负色散和低限制损耗的要求,比起通常的三角结构光纤有着更高的双折射率,并且结构制作也较简单。采用全矢量有限元法和各项异性完美匹配层法对所设计的光纤进行了仿真研究。仿真结果表明:该光纤在1.55μm波长处可获得10~(-2)数量级的双折射率,在较宽广的波段范围具有大的负色散,限制损耗低于10~(-9)dB/m;该光纤在保偏光纤、单极化单模光纤、色散补偿光纤等方面具有重要的应用。     

光子晶体光纤中高效的反斯托克斯信号产生

基于四波混频的反斯托克斯变换, 被广泛应用于短波辐射高分辨率成像以及直接激发分子的电子跃迁等方面. 为了实现更加高效的反斯托克斯变换, 利用中心波长为810 nm脉冲宽度为120 fs的钛蓝宝石(Ti: sapphire)飞秒激光器作为抽运光源, 在长度为0.5 m和3 m的光子晶体光纤中分别实现了高阶模和基膜的简并四波混频. 实验中, 采用的光子晶体光纤的零色散波长在820 nm附近. 在基模相位匹配条件下, 在560 nm附近实现了高效地反斯托克斯信号的产生, 反斯托克斯信号与残余抽运信号的最大功率比为33:1; 反斯托克斯信号和斯托克斯信号的最大功率比25:1; 反斯托克斯信号最大功率转换效率P_a/P_p0为34%. 抽运波长从790 nm逐渐增加到810 nm过程中, 在长为3 m的光子晶体光纤中相位从不匹配状态转化为高阶模匹配状态后, 再转化为基模匹配状态. 通过实验研究得出了相位匹配程度随抽运功率、波长和光纤长度的变化规律, 同时分析了造成理论计算与实验结果存在差异的主要因素. 本文为研究在光子晶体光纤基模中实现相位匹配和产生高效反斯托克斯信号提供了理论和实验依据.     

高双折射纳米结构光子晶体光纤特性研究

设计了一种高双折射高非线性纳米结构光子晶体光纤,利用电磁场散射的多极理论研究了这种光纤的双折射、基模模场、色散以及非线性特性.数值研究发现,加大纤芯及包层空气孔的非对称程度,可使双折射变大,其双折射最大值可达1.918×10-2.通过调节孔节距大小,可将双折射最大值调至所需波长处,孔节距为400nm的纳米光子晶体光纤在800nm波长处非线性系数高达0.2m-1.W-1,同时在750—1000nm的波段有较大的双折射值,高双折射和高非线性在纳米结构光子晶体光纤中实现了完美的结合.对新型纳米光子器件的研制和集成光学的发展具有重要意义.     

高温光子晶体光纤温度传感器

针对大于500℃的高温环境,提出了一种可用于高温温度测量的高温光子晶体光纤(PCF)温度传感器。在光子晶体光纤末端熔接一段纯石英无芯光纤构成外腔式光纤法珀腔(EFPI)结构。纯石英无芯光纤在高温下的热膨胀和热光效应使得EFPI的光学腔长发生变化。结合光纤白光干涉测量技术,通过测量EFPI的腔长得到被测温度。在不同温度环境下,对腔长为175μm的EFPI光纤温度传感器进行连续测量。测量结果显示,设计的高温光纤温度传感器在27~1100℃范围内,腔长-温度三阶拟合精度达到99.95%,腔长-温度灵敏度为(0.851+0.0023T-0.000000957T2)nm/℃,其中在1100℃时,温度测量分辨率为0.225℃。     

Optical parametric chirped pulse amplification based on photonic crystal fibre

A compact two-stage optical parametric chirped pulse amplifier based on photonic crystal fibre is demonstrated.A 1064-nm soliton pulse is obtained in a home-made photonic crystal fibre (PCF) with femtosecond pulse pumping and then amplified to 2 mJ in an Nd:YAG regenerative amplifier.After the amplified pulses pass through the LBO crystal,the 532-nm double-frequency light with an energy of 0.8 mJ and a duration of over 100 ps at 10-Hz repetition rate is generated as a pump source in the following two-stage optical parametric amplification (OPA).The 850-nm chirped signal light gain from the stretcher is 1.5×10 4 in the first-stage OPA while it is 120 in the second-stage OPA.The total signal gain of optical parametric chirped pulse amplification (OPCPA) can reach 1.8×10 6.     

微结构纤芯对光子晶体光纤基本特性的影响

本文设计了两种具有微结构纤芯的光子晶体光纤（PCFs）——矩形芯和椭圆芯PCFs,利用电磁场散射的多极理论研究了这两种光纤的基本特性.发现在光纤包层气孔不变的情况下,仅通过调节纤芯气孔的大小就可以灵活地调节光纤的双折射、色散和非线性特性.随着纤芯气孔半径r₁的增大,两种纤芯结构的PCFs表现出如下特点：双折射度增大且最大双折射度对应的波长发生红移,零色散波长由一个增加到三个,短波段非线性系数增大而长波段非线性系数减小.r₁=0.4 μm的椭圆芯PCFs的三个零色 关键词： 微结构纤芯光子晶体光纤 双折射 色散 非线性     

Propagation properties of an index guiding high birefringence fibre

Based on a full-vector model, a theoretical study on a kind of high birefringence photonic crystal fibre is presented. Due to introducing air holes of two different sizes into the cladding, twofold rotational symmetry was obtained. We demonstrate the possibility of achieving high birefringence that is at least one order of magnitude higher than that of conventional polarization-maintaining fibres. The dependences of modal birefringence, modal field and differential group delay on the structure parameter of the fibres are discussed in detail. The numerical results are in very good agreement with the experimental results in the literature.     

菱形纤芯光子晶体光纤色散与双折射特性分析

针对光子晶体光纤多零色散点、高双折射的应用要求, 设计了一种新型结构的光子晶体光纤, 其纤芯由位于菱形四个角上的圆形空气孔组成. 通过有限元数值分析方法对该种结构光子晶体光纤的色散特性和双折射特性进行数值仿真, 得到色散与波长、色散与纤芯圆孔尺寸、双折射与波长、双折射与纤芯圆孔尺寸的关系. 研究结果表明:在满足光纤传输功率要求的条件下, 光纤的双折射在d₁<0.8 μupm 时的性能较好. 同时, 该种结构的光子晶体光纤在芯区直径满足d₁=0.4 μupm或 d₁=0.6 μupm时会出现两个零色散点, 这对进一步研制具有多零色散点的光子晶体光纤具有重要的意义.     

A dark hollow beam from a selectively liquid-filled photonic crystal fibre

This paper reports that, based on the electromagnetic scattering theory of the multipole method, a high-quality hollow beam is produced through a selectively liquid-filled photonic crystal fibre. Instead of a doughnut shape, a typical hollow beam is produced by other methods; the mode-field images of the hollow-beam photonic crystal fibre satisfy sixth-order rotation symmetry, according to the symmetry of the photonic crystal fibre (PCF) structure. A dark spot size of the liquid-filled photonic crystal fibre-generated hollow beam can be tuned by inserting liquid into the cladding region and varying the photonic crystal fibre structure parameters. The liquid-filled PCF makes a convenient and flexible tool for the guiding and trapping of atoms and the creation of all-fibre optical tweezers.     

菱形纤芯光子晶体光纤色散与双折射特性分析

针对光子晶体光纤多零色散点、高双折射的应用要求, 设计了一种新型结构的光子晶体光纤, 其纤芯由位于菱形四个角上的圆形空气孔组成. 通过有限元数值分析方法对该种结构光子晶体光纤的色散特性和双折射特性进行数值仿真, 得到色散与波长、色散与纤芯圆孔尺寸、双折射与波长、双折射与纤芯圆孔尺寸的关系. 研究结果表明:在满足光纤传输功率要求的条件下, 光纤的双折射在d₁<0.8 μupm 时的性能较好. 同时, 该种结构的光子晶体光纤在芯区直径满足d₁=0.4 μupm或 d     

空气孔正方形排列的低损耗高双折射光子晶体光纤的数值模拟

提出了一种正方形排列渐增空气孔高双折射光子晶体光纤，并利用多极方法对光纤基模的模场分布、色散、双折射以及损耗特性进行了数值模拟.模拟结果表明利用这种结构可以在包层空气孔层数较少的情况下实现极低的限制损耗，通过调节内层空气孔的分布可以有效地控制光纤的双折射和色散特性.本结果对高双折射光子晶体光纤的制备具有一定的指导意义. 关键词： 光子晶体光纤 双折射 限制损耗 多极方法     

基于高双折射光子晶体光纤环镜的全光纤平顶梳状滤波器

A novel all-fibre flat-top comb filter based on a high birefringence photonic crystal fibre loop mirror is proposed and demonstrated. We simulate theoretically its output spectra and experimentally realize a flat-top output with a high extinction ratio. Compared to filters consisting of the conventional Panda polarization main- taining fibre, filters based on a high birefringence photonic crystal fibre loop mirror have better temperature stability. This kind of filter can be expected to be used widely in Wavelength-division-multiplexing（WDM） systems in the future.     

High birefringence, low loss terahertz photonic crystal fibres with zero dispersion at 0.3 THz

A terahertz photonic crystal fibre (THz-PCF) is designed for terahertz wave propagation. The dispersion property and model birefringence are studied by employing the finite element method. The simulation result reveals the changing patten of dispersion parameter versus the geometry. The influence of the large frequency band of terahertz on birefringence is also discussed. The design of low loss, high birefringence THz-PCFs with zero dispersion frequency at 0.3 THz is presented.