Ca3N2 as a flux for crystallization of GaN

In this work Ca₃N₂ was investigated as a potential flux for crystallization of GaN. Melting temperature of the potential flux at high N₂ pressure evaluated by thermal analysis as 1380 °C is in good agreement with the theoretical prediction. It is shown that Ca₃N₂ present in the liquid gallium in small amount (1 at%) dramatically accelerates synthesis of GaN from its constituents. On the other hand, it does not influence significantly the rate of GaN crystallization from solution in gallium in temperature gradient for both unseeded and seeded configurations. However the habit and color of the spontaneously grown GaN crystals change drastically. For 10 mol% Ca₃N₂ content in the liquid Ga it was found that the GaN thick layer and GaN crystals (identified by micro-Raman scattering measurements) were grown on the substrate. For growth from molten Ca₃N₂ (100%) with GaN source, the most important observations were (i) GaN source material was completely dissolved in the molten Ca₃N₂ flux and (ii) after experiment, GaN crystals were found on the sapphire substrate.     

Studies of the facetting of the polished (100) face of CaF2

The present paper deals with studies of the facetting of the polished (1 0 0) surface of CaF₂ during annealing and growth in UHV using low energy electron diffraction (LEED), atomic force microscopy (AFM), and transmission electron microscopy (TEM). First morphological modifications of the polished surfaces become visible at temperatures of T=874 K. Surfaces annealed at T=974 K exhibit a micro-roughening with pyramidal protrusions and corresponding depressions. LEED studies indicate the evolution of {1 1 1} facets. Reflexes from the (1 0 0) surface are not seen. After growth of about 660 monolayers of CaF₂ at T=1093 K and a saturation ratio S=33 from the vapor phase, larger pyramid-like or hip roof-like crystallites are developed. The results of AFM height profiles as well as of the LEED investigations indicate again the formation of {1 1 1} facets as proved by their angles of 54.7 ^o with the base (1 0 0) surface. This shows that the crystallites are homoepitaxially grown on the underlying CaF₂ substrate.     

Growth and characterization of KY(WO4)2 crystals

Single-crystal growth of KY(WO₄)₂ (KYW) by top-seeded solution growth technique has been investigated. The effects of seed orientation, temperature gradient experienced by the growing crystal and rate of crystallization on crystal quality are reported. The best results are obtained when the growth is seeded along the 0 1 0 direction. Minute deviations from this growth direction are found to be detrimental to crystal perfection. The differential thermal analysis shows that the amount of super-cooling required for dissolution and crystallization of KYW in the flux is only 5° and this promotes an easy formation of tiny crystallites in the solution. Consequently, the crystal rotation and the solution cooling rates are found to have pronounced effects on the growth of KYW crystal.     

Growth and shape control of orthorhombic Fe5(PO4)4(OH)3·2H2O single crystalline dendrites

Orthorhombic Fe₅(PO₄)₄(OH)₃·2H₂O single crystalline dendritic nanostructures have been synthesized by a facile and reproducible hydrothermal method without the aid of any surfactants. The influences of synthetic parameters, such as reaction time, temperature, the amount of H₂O₂ solution, pH values, and types of iron precursors, on the crystal structures and morphologies of the resulting products have been investigated. The formation process of Fe₅(PO₄)₄(OH)₃·2H₂O dendritic nanostructures is time dependent: amorphous FePO₄·nH₂O nanoparticles are formed firstly, and then Fe₅(PO₄)₄(OH)₃·2H₂O dendrites are assembled via a crystallization-orientation attachment process, accompanying a color change from yellow to green. The shapes and sizes of Fe₅(PO₄)₄(OH)₃·2H₂O products can be controlled by adjusting the amount of H₂O₂ solution, pH values, and types of iron precursors in the reaction system.     

The growth and spectroscopic characteristics of Ca3Y2(BO3)4:Er laser crystal

The Ca₃Y₂(BO₃)₄:Er³⁺ crystal with a size up to 20 mm×30 mm was grown by the Czochralski method. The absorption spectrum was measured and its absorption peaks were assigned to the corresponding transitions between the Er³⁺ energy levels. A broad emission spectrum from 1429.4 to 1662.8 nm was exhibited from 530 nm wavelength pumping. This crystal is promising as a tunable infrared laser crystal.     

Growth and photoluminescence properties of vertically aligned SnO2 nanowires

Vertically aligned SnO₂ nanowires (NWs) were grown for the first time by a vapor–liquid–solid method on c-sapphire with gold as a catalyst under Ar gas flow. Electron backscatter diffraction analysis indicated the NWs are single crystalline having the rutile structure, grow vertically along the [1 0 0] direction, and exhibit a consistent epitaxial relationship where lattice mismatch is estimated to be 0.3% along the SnO₂ [0 1 0] direction. The growth of these NWs is sensitive to many parameters, including growth duration, substrate type, source vapor concentration, and the thickness of the catalyst layer. Photoluminescence measurements at room temperature showed that the vertically aligned NWs exhibit an intense transition at 3.64 eV, a near band-edge transition which is rarely observed in SnO₂.     

Growth and scintillation properties of the Na2W2O7 crystal

The growth and scintillation properties of the Na₂W₂O₇ crystal are reported. The solid reaction between Na₂CO₃ and WO₃ is used to synthesise the Na₂W₂O₇ material. The Na₂W₂O₇ single crystal has been grown by the Bridgman method. And the Na₂W₂O₇ single crystal with sizes 14×7×6 mm³ has been achieved. The transmission spectra, the Ultraviolet fluorescence spectra and the X-ray excited luminescence spectra of the Na₂W₂O₇ crystal are measured. The measurement results show that the Na₂W₂O₇ crystal is a promising intrinsic scintillator.     

Growth and characterization of nanostructured Al2O3/YAG/ZrO2 hypereutectics with large surfaces under laser rapid solidification

The preparation of large bulk oxide eutectics with homogeneous and dense structure in nano-scale by melt growth method is a difficult challenge. Fully dense, homogeneous and crack-free ternary nanostructured Al₂O₃/YAG/ZrO₂ hypereutectic plate with large surface is successfully obtained by laser remelting. The hypereutectic in selected composition presents an ultra-fine eutectic-like microstructure consisting of alternating interpenetrating Al₂O₃, YAG and ZrO₂ lamellae with mean interphase spacing of about 150 nm, which is much smaller than the ternary eutectic composition grown at the same growth conditions. With the increase of laser scanning rate, the lamellar spacing is rapidly decreased. The minimum value obtained is 50 nm. The analysis indicates that the strong faceted growth behavior and cooperative branching of the component phases related with high entropies of fusion and large kinetic undercooling during laser rapid solidification are the primary formation reasons for the irregular eutectic growth morphology. Furthermore, the unique cellular microstructure with complex structure is also observed at high growth rate, and their formation mechanism and effect of the composition on the microstructure are discussed.     

Influence of some foreign metal ions on crystal growth kinetics of brushite (CaHPO4·2H2O)

Brushite, CaHPO₄·2H₂O, has been precipitated at 25 °C in the presence of Mg²⁺, Ba²⁺ or Cu²⁺ at concentrations up to 0.5 mM. When initial pH is sufficiently low to exclude nanocrystalline apatite as the initial solid phase, overall crystal growth rate may be determined from simple mass crystallization by recording pH as function of time. A combination of surface nucleation (birth-and-spread) and spiral (BCF) growth was found. Edge free energy was determined from the former contribution and was found to be a linear function of chemical potential of the additive, indicating constant adsorption over a wide range of additive concentrations. Average distances between adsorbed additive ions as calculated from slopes of plots are compatible with lattice parameters of brushite: 0.54 nm for Mg²⁺, 0.43 nm for Ba²⁺ and 0.86 nm for Cu²⁺. With the latter a sharp decrease in growth rate occurred early in the crystallization process, followed by an equally sharp increase to the previous level. When interpreted in terms of the Cabrera–Vermilyea theory of crystal growth inhibition, the results are consistent with an average distance between Cu ions of 0.88 nm, in perfect agreement with the above value.     

Self-catalytic branch growth of SnO2 nanowire junctions

Multiple branched SnO₂ nanowire junctions have been synthesized by thermal evaporation of SnO powder. Their nanostructures were studied by transmission electron microscopy and field emission scanning electron microcopy. It was observed that Sn nanoparticles generated from decomposition of the SnO powder acted as self-catalysts to control the SnO₂ nanojunction growth. Orthorhombic SnO₂ was found as a dominate phase in nanojunction growth instead of rutile structure. The branches and stems of nanojunctions were found to be an epitaxial growth by electron diffraction analysis and high-resolution electron microscopy observation. The growth directions of the branched SnO₂ nanojunctions were along the orthorhombic [1 1 0] and . A self-catalytic vapor–liquid–solid growth mechanism is proposed to describe the growth process of the branched SnO₂ nanowire junctions.     

Growth and optical properties of self-frequency-doubling laser crystal Yb:LuAl3(BO3)4

Single crystal of Yb:LuAl₃(BO₃)₄(Yb:LuAB) was grown by the flux method for the first time. The cell parameters of the grown crystal were estimated by X-ray diffraction analysis. The result indicates the symmetry of trigonal space group R32, with lattice parameters a=b=9.26372 Å, c=7.21405 Å, V=536.14 Å³, and Z=4. The absorption and emission spectra of Yb:LuAB crystal at room temperature has also been studied. The fluorescence lifetime for Yb:LuAB crystal is about 1.48 ms. The heat capacity was measured from 25 to 500 °C. Its second harmonic generation efficiency in LuAl₃(BO₃)₄ crystal is 3–4 times that of KDP crystal. These results show that Yb:LuAB crystal would be a potential self-frequency-doubling laser crystal.     

Growth, refined structural and spectroscopic characteristics of Tm-doped NaGd(WO4)2 single crystals

The details of Tm³⁺-doped NaGd(WO₄)₂ single-crystal growth are discussed, the results of precise investigations of its structural and spectroscopic characteristics, as well as the analysis of cross-relaxation process of Tm³⁺ ions (³H₄→³F₄, ³H₆→³F₄) in this crystal are presented. Based on the Judd–Ofelt theory, three intensity parameters, spontaneous emission probabilities, fluorescence branching ratios and fluorescence quantum efficiency from ³H₄ and ³F₄ levels were refined.     

Growth and spectroscopic properties of Er single doped and Er–Yb co-doped YAl3(BO3)4 crystals

Er³⁺-doped and Er³⁺–Yb³⁺ co-doped yttrium aluminum borate (YAB) single crystals have been grown by the top-seeded solution growth method using a new flux system, namely NaF–MoO₃–B₂O₃. The Er³⁺ concentrations were 1.3 mol% for both single doped and co-doped crystals and the Yb³⁺ concentration in the Er³⁺–Yb³⁺ co-doped crystal was 20.0 mol% in the raw materials. The distribution coefficients of Er³⁺ single doped and Er³⁺–Yb³⁺ co-doped crystals were measured. The polarized absorption and fluorescence spectra of Er³⁺–Yb³⁺ co-doped crystal were recorded and compared with those of Er³⁺ single doped crystal. The results demonstrate that Er³⁺–Yb³⁺ co-doped YAB crystal is a potential candidate for 1.55 μm laser materials.     

Crystal growth of KInO2 from a hydroxide flux

Single crystals of KInO₂ were obtained from a reactive potassium hydroxide flux at 700 °C. KInO₂ crystallizes in the R-3m crystal system with a=3.2998(10) Å, c=18.322(10) Å and V=172.78(12) Å³. The crystal structure is isotypic with that of α-NaFeO₂ and consists of the (1 1 1) layers being occupied alternately by KO₆ and InO₆ octahedra. Three different AInO₂ structure types are discussed.     

Growth of NaBi(WO4)2 crystal by modified-Bridgman method

NaBi(WO₄)₂ (NBW) crystals have been grown for the first time by modified-Bridgman method. Influences of some factors on the crystal growth process are discussed. X-ray powder diffraction experiments show that the unit cell parameters of NBW crystal are a=b=0.5284 nm, c=1.1517 nm, and V=0.3215 nm³. The differential thermal analysis shows that the NBW crystal melts at 923°C.     

Growth and microstructural features of laser ablated LiCoO2 thin films

Thin films of LiCoO₂ were prepared by pulsed laser deposition technique and the properties were studied in relation to the deposition parameters. The films deposited from a sintered composite target (LiCoO₂+Li₂O) in an oxygen partial pressure of 100 mTorr and at a substrate temperature of 300 °C exhibited preferred c-axis (0 0 3) orientation perpendicular to the substrate surface. The AFM data demonstrated that the films are composed of uniform distribution of fine grains with an average grain size of 80 nm. The grain size increased with an increase in substrate temperature. The (0 0 3) orientation decreased with increase in (1 0 4) orientation for the films deposited at higher substrate temperatures (>500 °C) indicating that the films’ growth is parallel to the substrate surface. The composition of the experimental films was analyzed using X-ray photoelectron spectroscopy (XPS). The binding energy peaks of Co(2p_3/2) and Co(2p_1/2) are, respectively, observed at 779.3 and 794.4 eV, which can be attributed to the Co³⁺ bonding state of LiCoO₂. The electrochemical measurements were carried out on Li//LiCoO₂ cells with a lithium metal foil as anode and LiCoO₂ film as cathode of 1.5 cm² active area using a Teflon home-made cell hardware. The Li//LiCoO₂ cells were tested in the potential range 2.6-4.2 V. Specific capacity as high as 205 mC/cm² μm was measured for the film grown at 700 °C. The growth of LiCoO₂ films were studied in relation to the deposition parameters for their effective utilization as cathode materials in solid-state microbattery application.     

Growth and spectral properties of Nd-doped Sr3Y(BO3)3 crystal

A new crystal of Nd³⁺:Sr₃Y(BO₃)₃ with dimension up to 25×35 mm² was grown by Czochralski method. Absorption and emission spectra of Nd³⁺: Sr₃Y(BO₃)₃ were investigated . The absorption band at 807 nm has a FWHM of 18 nm. The absorption and emission cross sections are 2.17×10⁻²⁰ cm² at 807 nm and 1.88×10⁻¹⁹ cm² at 1060 nm, respectively. The luminescence lifetime τ_f is 73 μs at room temperature     

Densities of Li2O–B2O3 melts

The densities have been systematically measured in xLi₂O–(1−x)B₂O₃ melts of different compositions with Li₂O content varying from x=0 to 0.68 from their respective melting points up to about 1450 K with a modified Archimedean method. The density decreased with increasing temperature for all the melts measured in this work. When x<0.15, the plot of temperature versus density could be well fitted by a quadratic polynomial function, and when x0.15, density decreased linearly with increasing temperature. At a fixed temperature, the density of the melts increased rapidly with Li₂O content, went through a maximum at about x=0.333 (Li₂O–2B₂O₃), and then decreased slowly as Li₂O content was further increased. In addition, the volume expansion coefficient (β) was calculated based on the densities measured in this work, and it was found that a maximum value appeared in the dependence of β on the molar ratio of Li₂O at about x=0.333.     

Growth and properties of Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 single crystals directly from melt

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by a modified Bridgman method directly from melt using an allomeric Pb[(Mg_1/3Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal as a seed. X-ray diffraction (XRD) measurement confirmed that the as-grown PZNT91/9 single crystals are of pure perovskite structure. Electrical properties and thermal stabilization of PZNT91/9 crystals grown directly from melt exhibit different characters from those of PZNT91/9 crystals grown from flux, although segregation and the variation of chemical composition are not seriously confirmed by X-ray fluorescence analysis (XPS). The [0 0 1]-oriented PZNT91/9 crystals cut from the middle part of the as-grown crystal boules exhibit broad dielectric-response peaks at around 105 °C, accompanied by apparent frequency dispersion. The values of piezoelectric constant d₃₃, remnant polarization P_r, and induced strain are about 1800–2200 pC/N, 38.8 μC/cm², and 0.3%, respectively, indicating that the quality of PZNT crystals grown directly from melt can be comparable to those of PZNT91/9 single crystals grown from flux. However, further work deserves attention to improve the dielectric properties of PZNT crystals grown directly from melt. Such unusual characterizations of dielectric properties of PZNT crystals grown directly from melt are considered as correlating with defects, microinhomogeneities, and polar regions.     

Thermal-induced phase transition and assembly of hexagonal metastable In2O3 nanocrystals: A new approach to In2O3 functional materials

This paper reports on the thermal-induced performance of hexagonal metastable In₂O₃ nanocrystals involving in phase transition and assembly, with particular emphasis on the assembly for the preparation of functional materials. For In₂O₃ nanocrystals, the metastable phase was found to be thermally unstable and transform to cubic phase when temperature was higher than 600 °C, accompanied by assembly as well as evolution of optical properties, but the two polymorphs coexisted at the temperature ranging from 600 to 900 °C, during which the content of product phase and crystal size gradually increased upon increasing temperature. The assembly of In₂O₃ nanocrystals can be developed to fabricate In₂O₃ functional materials, such as various ceramic materials, or even desired nano- or micro-structures, by using metastable In₂O₃ nanocrystals as precursors or building blocks. The electrical resistivity of In₂O₃ conductive film fabricated by a hot-pressing route was as low as 3.72×10⁻³ Ω cm, close to that of In₂O₃ single crystal, which is important for In₂O₃ that is always used as conductive materials. The findings should be of importance for both the wide applications of In₂O₃ in optical and electronic devices and theoretical investigations on crystal structures.