新型氧化铝模板自组装制备非晶碳纳米点阵列膜及其场发射性能研究

通过对阳极氧化铝(AAO)模板进行特殊扩孔处理,消除了AAO模板中带电阴离子对沉积碳离子的不良影响,利用磁过滤阴极弧等离子体沉积技术成功制备了非晶碳纳米尖点阵列膜.场发射扫描电镜(FESEM)分析表明,经过氧化和扩孔多步处理制备的AAO模板具有特殊的开口结构,制备的非晶碳纳米尖点阵列完整地复制了AAO模板的孔道阵列结构,纳米点排列整齐有序,直径约100nm,密度达1010cm-2,样品的场发射测试显示,非晶碳纳米点阵列具有良好的电子发射性能,发射电流为10mA/cm-2时的阈值电场为3.7V/μm.     

一种可控纳米柱阵列的研制

在一次阳极氧化法制备多孔氧化铝(anodized aluminum oxide,AAO)的基础上,进行了二次、三次、四次氧化制备AAO,并对多次氧化制备多孔AAO的电流变化曲线和模板表面的形貌特点等进行了比较分析.二次、三次、四次氧化制备的AAO纳米孔孔径依次增大、孔间距减小,而模板表面的纳米孔有序性分布没有明显变化.控制一次氧化AAO模板的除膜时间,～10 min即可得到孔径规则、高度有序的AAO膜.最后,利用所制备的不同孔深和孔径的AAO为模板,通过热纳米压印复制技术制备了长度和直径等性质可控的PMMA纳米柱阵列. 关键词： 纳米柱阵列 聚甲基丙烯酸甲酯 多孔氧化铝模板 多次氧化法     

铝基银纳米阵列制备及其紫外-可见-近红外光吸收特性

基于阳极氧化铝模板,采用真空蒸镀技术,制备了高度有序的周期性银纳米球阵列.阵列几何结构参数调控实验发现,通过控制蒸镀厚度,可实现对阵列中银纳米球尺寸(直径)和间距的有效调控,进而有效实现对紫外-可见-近红外各波段吸收峰位和峰宽的调制.吸收光谱测试显示,该纳米阵列在紫外、可见和近红外波段都具有明显的电磁波吸收特性.时域有限差分理论模拟结合实验分析不同波段光吸收特性的物理机制,紫外超窄强吸收为银、铝介电环境非对称诱发的法诺共振,可见波段吸收源自于银纳米粒子局域表面等离子体共振,近红外波段强吸收为银纳米球阵列表面晶格共振所激发.     

Co/AAO纳米有序阵列复合结构的光致发光和光吸收特性

以草酸电解液制备的高度有序的纳米级多孔阳极氧化铝(AAO)为模板,采用交流电化学沉积工艺合成了Co/AAO纳米有序阵列复合结构。分别研究了AAO模板和Co/AAO结构的光致发光和光吸收特性。结果表明,AAO模板在350～550nm范围内存在较强的光致发光带,其峰位在395nm处;Co/AAO纳米有序阵列复合结构的光致发射峰位亦在395nm处,且发光峰强度随Co沉积量的增加而迅速减弱。实验发现,Co/AAO纳米有序阵列复合结构的光吸收边从近紫外至近红外的波段范围内发生大幅度红移,最大红移量甚至超过380nm。文章定性分析并解释了Co/AAO纳米有序阵列复合结构吸收边大幅度红移及其光发射峰位不变、而峰强减弱的主要原因。     

银纳米有序阵列SERS活性基底的制备及在膀胱肿瘤细胞检测中的应用

以多孔阳极氧化铝(porous anodic alumina,PAA)膜为模板,采用真空电子束蒸镀技术,分别在PAA多孔层以及阻挡层表面形成了银纳米孔和银纳米帽有序阵列表面增强拉曼散射(surface-enhancedRaman scattering,SERS)活性基底,并以膀胱肿瘤细胞作为分子探针,测试和分析了这两种SERS活性基底的表面增强拉曼光谱的特性。结果表明,两种SERS活性基底对膀胱肿瘤细胞的拉曼散射信号均有很好的增强作用。银纳米帽有序阵列SERS活性基底不仅具有较高的SERS增强和荧光猝灭效应,而且不存在与PAA膜中草酸根杂质相关的干扰峰,可获得膀胱肿瘤细胞拉曼散射光谱的更多细节信息。     

金纳米空心半球壳膜的可调谐光学性质研究

以单层聚苯乙烯微球阵列为模板,通过控制其表面金膜蒸镀时间,制备了具有不同厚度的空心半球壳结构的金纳米膜.利用扫描电子显微镜和自制光谱仪分别测量了金膜表面形貌和其透射光谱,并分析了金膜形貌与其光学性质间的关系,同时以4-巯基苯胺为探针分子测定了金膜的表面增强喇曼散射效应.结果表明,该金纳米膜的表面等离子体共振波长随膜厚度增大而发生红移,在可见与近红外波段较宽范围内可调谐,并且,当金膜共振波长与入射激发光波长较近时,探针分子可产生出较强的表面增强喇曼信号.同时,对该现象的产生机制也进行了理论解释.     

电子束蒸发法在多孔氧化铝膜上制备银纳米点阵列

采用二步阳极氧化法在草酸溶液中制备了高度有序的多孔阳极氧化铝(Porous Anodic Alumina,PAA)薄膜。以多孔氧化铝薄膜为模板,采用真空电子束蒸发的方法在多孔氧化铝模板上制备出了高度有序的金属银纳米点阵列体系。扫描电镜(SEM)测试结果表明,所制备的金属银纳米点阵列与多孔阳极氧化铝膜的多孔阵列具有完全相同的有序结构,阵列中银纳米颗粒的形状接近球形,其直径大约为70nm,与氧化铝模板的孔径基本一致。研究了高度有序银纳米点阵列的形成过程。     

Si基AAO模板法制备尖晶石型ZnAl2O4纳米结构

以Si基AAO为模板,以Zn和C粉作蒸发源,通过化学气相沉积法,在不同的温度下反应得到了不同的ZnAl2O4纳米结构.对样品的形貌和成分结构进行了分析.扫描电镜结果显示,在800℃获得的ZnAl2O4样品表面仍保留着AAO模板的孔洞结构.而XRD结果表明,在700,800,900℃下获得的样品都出现了ZnAl2O4衍射...     

多孔氧化铝膜上自组织生长Sn纳米点阵列的研究

以多孔阳极氧化铝膜(porous anodic alumina, PAA)为基片，采用真空电子束蒸发的方法在多孔氧化铝膜上制备了高度有序度的Sn纳米点阵列.锡纳米点阵的XRD与块体锡的完全相同，扫描电镜(SEM)测试结果表明，所制备的金属Sn纳米点阵与阳极氧化铝膜的多孔阵列具有完全相同的有序结构，阵列中每个Sn纳米粒子的形状为球形的，其直径接近于PAA膜的孔直径.对Sn纳米点阵形成过程和形成机理进行了讨论.     

利用AAO模板制备SERS基底检测SudanⅠ

通过模板法制备大面积、可控的、可重复的、热点集中的金纳米结构阵列,并在纳米结构阵列上通过化学修饰分子,吸附更多苏丹红Ⅰ分子至金纳米的SERS增强区域,实现其高灵敏的表面增强拉曼分析检测。以多孔阳极氧化铝为模板,通过真空蒸镀金,约200 nm厚度,复制氧化铝的孔洞结构,用碱液将氧化铝模板腐蚀去除,可得到氧化铝模板的互补结构,即大面积的、均匀的金半球纳米结构阵列。在金纳米结构阵列上修饰十二硫醇,硫醇巯基端与纳米金相结合,碳链端自组装形成非极性的疏水环境,疏水环境可以捕获苏丹红Ⅰ分子,使其吸附至纳米金结构表面的SERS增强区域,实现苏丹红Ⅰ的SERS检测。由于SERS基底表面的金半球纳米结构均匀、规整,在激光光斑的区域内,苏丹红Ⅰ的SERS信号均匀、稳定,可以对苏丹红Ⅰ进行定量分析。苏丹红Ⅰ的拉曼峰强度对数与浓度对数之间呈线性关系,线性相关系数达0.99,线性范围为5×10-4～10-7mol·L-1,回收率范围77%～117%。此方法的检测限可达到4×10-8mol·L-1,与国标的高效液相色谱的检测限相当。     

Nanoscale carbon tubules deposited in anodic aluminium oxide template： a study of soft x-ray transmission

Well-aligned, catalyst-free nanoscale carbon tubules array was prepared by organic compound vapour deposition method using anodic aluminium oxide (AAO) as a template. The experiment of soft x-ray channelling in such carbon tubules array deposited in AAO template was performed at Beijing Synchrotron Radiation Facility. The transmission of x-rays in carbon tubules array with AAO template support was found even higher than that in bare AAO template at high-energy part of energy spectrum though the porous area of the former was smaller than that of the latter. A qualitative explanation is presented to interpret our results.     

AFM study of gold nanowire array electrodeposited within anodic aluminum oxide template

Uniform gold nanowires were synthesized by electrodepositing the gold under a very low ac frequency in the pores of an anodic aluminum oxide (AAO) template. The surface of the Au/AAO composite is very even and appeared purplish red. Atomic force microscopy observation indicates that the template membranes we obtained have hexagonally close-packed nanochannels. The gold nanowire array is very orderly arranged after partially dissolving the aluminum oxide membrane. Gold nanowires were also characterized by transmission electron microscopy and the phase structure of the Au/AAO composite was proved by X-ray diffraction. Received: 19 April 2001 / Accepted: 28 April 2001 / Published online: 27 June 2001     

Read/write characteristics of a new type of bit-patterned-media using nano-patterned glassy alloy

The paper reports a feasibility study of new type bit-patterned-media using a nano-patterned glassy alloy template for ultra-high density hard disk applications. The prototype bit-patterned-media was prepared using a nano-hole array pattern fabricated on a Pd-based glassy alloy thin film and a Co/Pd multilayered film filled in the nano-holes. The prepared prototype bit-patterned-media had a smooth surface and isolated Co/Pd multilayer magnetic dots, where the average dot diameter, the average dot pitch and the average dot height were 30, 60 and 19 nm, respectively. MFM (magnetic force microscope) observation revealed that each dot was magnetized in a perpendicular direction and the magnetization could reverse when an opposite magnetic field was applied. Static read/write tester measurements showed that repeated writing and reading on isolated magnetic dots were possible in combination with conventional magnetic heads and high-accuracy positioning technologies. The present study indicates that the new type of bit-patterned-media composed of nano-hole arrays fabricated on glassy alloy film template and Co/Pd multilayer magnetic dots are promising for applications to next generation ultra-high density hard disk drives.     

强辐射源用铜纳米线阵列靶的结构与性能

 采用多孔阳极氧化铝（AAO）模板脉冲电沉积法制备了强辐射源用铜纳米线阵列靶,并用扫描电子显微镜（SEM）、能谱（EDS）和X射线衍射（XRD）对其进行了结构表征。结果表明：去除AAO模板后铜纳米线平均直径比去除AAO模板前的平均孔径大32%,长度缩短5%。对电沉积2 000 s的样品进行铜纳米线长度分布表征,结果显示:距离模板圆心越远,铜纳米线越长。与超短脉冲激光相互作用实验结果表明:纳米线平均长度在18~50 μm范围内,铜Kα光子产额先随纳米线长度增加而增加,当长度大于33 μm时,铜Kα光子产额开始下降。     

Photoemission electron microscopy of a plasmonic silver nanoparticle trimer

Anodic aluminum oxide (AAO) films with different porosities were fabricated on the surfaces of InGaN/GaN multiple quantum wells (MQWs). We measured the photoluminescence spectra of these samples and then calculated the light extraction enhancement factors (E). It was found that the light extraction of the MQWs with the AAO films has been greatly enhanced compared to the area without AAO coverage. The maximum value of E reaches 3.5 at a certain wavelength and 2.29 in the integral intensity. The increase of E with the decrease of the porosities demonstrates that the nano-hole structure in the AAO films plays an important role in enhancing the light extraction efficiency.     

Comparison of Surface-Enhanced Raman Scattering Spectra of Azo Dye Sudan III on Several Substrates

On several substrates, including dried silver-coated filter paper, electro-polishing aluminum foils, and anodic aluminum oxide (AAO) nanometer array templates, surface-enhanced Raman scattering (SERS) spectra of Azo Dye Sudan III molecules were studied, and high-quality SERS spectra were obtained, which indicated that electro-polishing aluminum foils and AAO nanometer array templates were also active SERS substrates. A number of additional modes were presented, as well as some split peaks, which were especially obvious on electro-polishing aluminum foil and AAO nanometer array template. The enhancement mechanisms were discussed and the enhancement factors G were calculated as 10⁴, 10⁶, and 10⁵, respectively.     

强辐射源用铜纳米线阵列靶的结构与性能

采用多孔阳极氧化铝（AAO）模板脉冲电沉积法制备了强辐射源用铜纳米线阵列靶,并用扫描电子显微镜（SEM）、能谱（EDS）和X射线衍射（XRD）对其进行了结构表征。结果表明：去除AAO模板后铜纳米线平均直径比去除AAO模板前的平均孔径大32%,长度缩短5%。对电沉积2 000 s的样品进行铜纳米线长度分布表征,结果显示:距离模板圆心越远,铜纳米线越长。与超短脉冲激光相互作用实验结果表明:纳米线平均长度在18~50 μm范围内,铜Kα光子产额先随纳米线长度增加而增加,当长度大于33 μm时,铜Kα光子产额开始下降。     

α-Fe纳米线阵列膜磁各向异性的穆斯堡尔谱研究

在具有纳米级孔洞的多孔氧化铝模板上,用电沉积方法成功地制备出α-Fe纳米线有序阵列组装膜.分别用透射电子显微镜(TEM)、穆斯堡尔谱仪(MS)和振动样品磁强计(VMS)对样品进行了测试分析.TEM和电子衍射的结果显示,阵列中的纳米线均匀有序,彼此独立,由一串α-Fe单晶磁性颗粒构成.VSM测试结果表明,这种纳米阵列结构具有高度垂直磁各向异性.当外磁场垂直磁化时,磁滞回线具有很高矩形比(0.98)和矫顽力(1.76×10⁵A/m).尤其MS的测试结果显示,阵列中的每根纳米线的总磁矩都沿 关键词：     

纳米压印多孔硅模板的研究

纳米压印模板通常采用极紫外光刻、聚焦离子束光刻和电子束光刻等传统光刻技术制备,成本较高.寻找一种简单、低成本的纳米压印模板制备方法以提升纳米压印光刻技术的应用成为研究的重点与难点.本文以多孔氧化铝为母模板,采用纳米压印光刻技术对纳米多孔硅模板的制备进行了研究.在硅基表面成功制备出纳米多孔阵列结构,孔间距为350—560 nm,孔径在170—480 nm,孔深为200 nm.在激发波长为514 nm时,拉曼光谱的测试结果表明,相对于单面抛光的硅片,纳米多孔结构的硅模板拉曼光强有了约12倍左右的提升,对提升硅基光电器件的应用具有重要的意义.最后,利用多孔硅模板作为纳米压印母模板,通过热压印技术,成功制备出了聚合物纳米柱软模板.