CO oxidation over Co3O4/SiO2 catalysts: Effects of porous structure of silica and catalyst calcination temperature

The catalytic performances of Co3O4/SiO2 catalysts prepared by incipient wetness impregnation for CO oxidation were investigated using three kinds of silica as carriers with different pore sizes of 7.7, 14.0 and 27.0 nm. The effects of calcination temperature on the catalyst surface and micro structure properties as well as catalytic performance for the oxidation of carbon monoxide were also studied. All catalysts were characterized by N2 adsorption-desorption, XRD, XPS, FTIR, H2-TPR and O2-TPD. It was found that the properties and crystal size of cobalt-containing species strongly depended on the pore size of silica carrier. While the silica pore size increased from 7.7 to 27.0 nm, the Co3O4 crystal size increased from 8.5 to 13.5 nm. Moreover, it was demonstrated that if the spinel crystal structure of Co3O4 was obtained at a calcination temperature as low as 150 ℃, the catalyst sample would have a high Co3O4 surface dispersion and a increase of surface active species, and thus exhibit a high activity for the oxidation of carbon monoxide.     

Comparative study of LaNiO3 and La2NiO4 catalysts for partial oxidation of methane

The catalytic activity and stability of LaNiO₃ and La₂NiO₄, prepared using a citric acid complex method, have been investigated for partial oxidation of methane (POM) to synthesis gas. The catalysts were characterized by thermo-gravimetric analysis (TG), temperature-programmed reduction (TPR) and temperature-programmed desorption of ammonia (NH₃-TPD). The results show that the catalytic activity and stability of La₂NiO₄ are higher than those of LaNiO₃, due to the stronger interactions between Ni and La₂O₃ in La₂NiO₄ and to its lower acidity as demonstrated by TPR and NH₃-TPD. TG result indicates that carbon deposition occurs on both catalysts, and the carbon species deposited on La₂NiO₄ are mainly metal carbides, while on LaNiO₃ are mainly graphite.     

Effect of La2O3 on Catalytic Performance of Au/TiO2 for CO Oxidation

Pure TiO₂ and La-doped TiO₂ were prepared by the sol-gel method. Au was supported on TiO₂ by the deposition-precipitation (DP) method, and its catalytic activity for CO oxidation was tested. The results showed that doping La in Au/TiO₂ could improve its catalytic activity obviously for CO oxidation. The analyses of X-ray diffraction (XRD), temperature-programmed desorption (TPD), and Brunauer-Emmett-Teller (BET) surface area further showed that the presence of La in TiO₂ not only increased its surface area and restrained the growth of TiO₂ crystallites, but could also enhance the microstrain of TiO₂. In terms of O₂-TPD, a new adsorbed species O⁻ appeared on the surface of La-doped TiO₂. The results of in-situ Fourier transform-infrared (FT-IR) spectroscopy illustrated that the high activity of Au/La₂O₃-TiO₂ was attributed to the presence of La promoting the reactivity of CO adsorbed on the Au site and the formation of the second active site on the surface of TiO₂     

BiVO4/ZnFe2O4同型异质结光阳极的构筑及其光电催化分解水性能

光生电子-空穴对的复合被认为是限制BiVO₄材料光电催化转换效率的重要原因之一。基于此,通过简单的水热-煅烧方法构筑了 BiVO₄/ZnFe₂O₄同型异质结光阳极,BiVO₄/ZnFe₂O₄复合光阳极在 1.23 V(vs RHE)下的光电流密度为 3.33 mA·cm^-2,较纯BiVO₄提升了2倍 (1.20 mA·cm^-2)。相关的结构及性能测试表明,BiVO₄和ZnFe₂O₄形成了带隙错开的n-n异质结,使得光生载流子得到有效分离,更有效地参与水氧化过程,进而提高了BiVO₄的光电催化水分解性能。     

BiVO4/ZnFe2O4同型异质结光阳极的构筑及其光电催化分解水性能

光生电子-空穴对的复合被认为是限制BiVO₄材料光电催化转换效率的重要原因之一。基于此,通过简单的水热-煅烧方法构筑了BiVO₄/ZnFe₂O₄同型异质结光阳极,BiVO₄/ZnFe₂O₄复合光阳极在1.23 V(vs RHE)下的光电流密度为3.33 mA·cm^-2,较纯BiVO₄提升了2倍(1.20 mA·cm^-2)。相关的结构及性能测试表明,BiVO₄和ZnFe₂O₄形成了带隙错开的n-n异质结,使得光生载流子得到有效分离,更有效地参与水氧化过程,进而提高了BiVO₄的光电催化水分解性能。     

制备方法对Fe2O3/Al2O3-ZrO2在乙苯脱氢反应中催化性能的影响

为提高含铁催化剂的脱氢活性,采用浸渍法和一步沉淀法制备了Fe、Al和Zr含量相同的F4AZ10-imp和F4AZ10-pre催化剂,在550 ℃考察了其在乙苯CO₂氧化脱氢制苯乙烯反应过程中的催化性能,并结合XRD、N₂-吸附、NH₃-TPD、CO₂-TPD和H₂-TPR等表征手段对催化剂进行了分析。结果表明,与浸渍法相比,一步沉淀法制备的催化剂更有利于活性组分Fe₂O₃在催化剂表面的分散及反应物CO₂的转化。     

Effect of Calcination Temperature on Surface Oxygen Vacancies and Catalytic Performance Towards CO Oxidation of Co3O4 Nanoparticles Supported on SiO2

Co₃O₄/SiO₂ catalysts for CO oxidation were prepared by conventional incipient wetness impregnation followed by calcination at various temperatures. Their structures were char-acterized with X-ray diffraction (XRD), laser Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction (TPR) and X-ray absorption fine structure (XAFS) spectroscopy. Both XRD and Raman spectroscopy only detect the ex-istence of Co₃O₄ crystallites in all catalysts. However, XPS results indicate that excess Co²⁺ ions are present on the surface of Co₃O₄ in Co₃O₄(200)/SiO₂ as compared with bulk Co₃O₄. Meanwhile, TPR results suggest the presence of surface oxygen vacancies on Co₃O₄ in Co₃O₄(200)/SiO₂, and XAFS results demonstrate that Co₃O₄ in Co₃O₄(200)/SiO₂ con-tains excess Co²⁺. Increasing calcination temperature results in oxidation of excess Co²⁺ and the decrease of the concentration of surface oxygen vacancies, consequently the for-mation of stoichiometric Co₃O₄ on supported catalysts. Among all Co₃O₄/SiO₂ catalysts,Co₃O₄(200)/SiO₂ exhibits the best catalytic performance towards CO oxidation, demon-strating that excess Co²⁺ and surface oxygen vacancies can enhance the catalytic activity of Co₃O₄ towards CO oxidation. These results nicely demonstrate the effect of calcination temperature on the structure and catalytic performance towards CO oxidation of silica-supported Co₃O₄ catalysts and highlight the important role of surface oxygen vacancies on Co₃O₄.     

焙烧与预处理条件对 Co3O4 催化氧化 CO 性能的影响

采用沉淀法制备了 Co₃O₄, 考察了焙烧和预处理条件对其结构、低温催化氧化 CO 性能的影响. 热重分析表明, 未经焙烧的样品以 Co(OH)₂CO₃ 的形式存在, 150~400 ^oC 空气气氛中焙烧后, 样品以立方相 Co₃O₄ 的形式存在. N2 吸附-脱附法、X 射线衍射、透射电镜及活性测试结果表明, 以纳米颗粒物存在的 Co₃O₄ 的比表面积、颗粒尺寸、催化氧化 CO 活性与焙烧温度密切相关. 正电子湮没寿命谱、O₂-程序升温脱附与定温条件下 CO 氧化测试结果表明, 合适温度 (150~250 ^oC) 下 N₂ 预处理有利于 Co₃O₄ 表面氧空穴团的形成, 它在吸附活化分子氧以及 CO 催化氧化反应中起到关键作用. 同时讨论了预处理作用下Co₃O₄表面氧空穴的再构机制.     

Influence of support on resistance to carbon-deposition of catalyst for CH4, CO2 with O2 to synthesis gas

In the reaction of catalytic oxidation of CH₄, CO₂ with O₂ to synthesis gas, carbon-deposition is an important factor for deactivation. By adding different oxides to Ni/Al₂O₃ catalyst, its resistance to carbon-deposition was improved. The experimental results indicate that the order of resistance to carbon-deposition is as follows: Ni/CaO-Al₂O₃>Ni/MgO-Al₂O₃>Ni/ TiO₂-Al₂O₃ > Ni/CeO₂-Al₂O₃>Ni/La₂O₃-Al₂O₃>Ni/Y₂O₃-Al₂O₃>Ni/Fe₂O₃-Al₂O₃>Ni/Al₂O₃. The catalysts were characterized by CO₂-TPD, O₂-TPD and XPS methods. Here the relation between the order of resistance to carbon-deposition and performance of catalyst is discussed.     

SO2对La0.8K0.2Cu0.05Mn0.95O3钙钛矿催化剂氧化碳烟的影响

采用柠檬酸配位法制备K、Cu掺杂的Lu0.8K0.2Cu0.05Mn0.95O3钙钛矿催化剂,运用程序升温氧化(TPO)考察在不同浓度SO2气氛下La0.8K0.2Cu0.05Mn0.95O3催化剂催化氧化模拟碳黑的性能,并用XRD、FFIR和XPS等进行表征.结果表明,催化剂在0～0.1%的SO2气氛中呈现出不同活性,φSO2≤0.05%的气氛可促进催化剂催化氧化碳黑的活性,当φSO2=0303%,催化剂活性最高;引入φSO2≥0.06%时催化剂活性明显下降.XPS说明表面活性氧的增加是低浓度的SO2促进催化活性的原因,同时XRD、FTIR结果表明高浓度的SO2所产生的大量SO42-是抑制催化剂活性的原因.     

Study of Ce0.7Sn0.3O2 supported PdO catalysts for CO oxidation

Palladium supported by Ce_0.7Sn_0.3O₂ has been prepared by an impregnation method, and used for low temperature carbon monoxide oxidation. They were characterized by means of XRD and H₂-TPR techniques. For PdO/Ce_0.7Sn_0.3O₂ catalyst, three reduction peaks (α, β and γ) are observed. The β peak contributes to the reduction of PdO species and Sn⁴⁺ species on the surface of Ce_0.7Sn_0.3O₂; β peak to the reduction of bulk SnO₂ and surface Ce⁴⁺and the γ peak to the reduction of bulk CeO₂. The increase of Pd loading from 0 to 0.75% enhances oxidation of CO, further increase of the Pd content affects the catalytic activity but slightly. XRD and TPR results show that highly dispersed Pd on the surface of the support is the active species for CO oxidation. This revised version was published online in June 2006 with corrections to the Cover Date.     

(La0.8A0.2)MnO3 (A = Sr,K) perovskite catalysts for NO and C10H22 oxidation and selective reduction of NO by C10H22

In this work, we studied the catalytic activity of LaMnO₃ and (La_0.8A_0.2)MnO₃ (A = Sr, K) perovskite catalysts for oxidation of NO and C₁₀H₂₂ and selective reduction of NO by C₁₀H₂₂. The catalytic performances of these perovskites were compared with that of a 2 wt% Pt/SiO₂ catalyst. The La site substitution increased the catalytic properties for NO or C₁₀H₂₂ oxidation compared with the non-substituted LaMnO₃ sample. For the most efficient perovskite catalyst, (La_0.8Sr_0.2)MnO₃, the results showed the presence of two temperature domains for NO adsorption: (1) a domain corresponding to weakly adsorbed NO, desorbing at temperatures lower than 270 ℃ and (2) a second domain corresponding to NO adsorbed on the surface as nitrate species, desorbing at temperatures higher than 330 ℃. For the Sr-substituted perovskite, the maximum NO₂ yield of 80% was observed in the intermediate temperature domain (around 285 ℃). In the reactant mixture of NO/C₁₀H₂₂/O₂/H₂O/He, (La_0.8Sr_0.2)MnO₃ perovskite showed better performance than the 2 wt% Pt/SiO₂ catalyst： NO₂ yields reaching 50% and 36% at 290 and 370 ℃, respectively. This activity improvement was found to be because of atomic scale interactions between the A and B active sites, Sr²⁺ cation and Mn⁴⁺/Mn³⁺ redox couple. Thus, (La_0.8Sr_0.2)MnO₃ perovskite could be an alternative free noble metal catalyst for exhaust gas after treatment.     

XAFS characterization of supported PdCl2?CuCl2 catalysts for CO oxidation

A heterogenized Wacker catalyst system in which pores of a high surface area alumina were filled with an aqueous solution of PdCl₂–CuCl₂ was active for the oxidation of CO near room temperature. The structure of thecatalyst was studied by XRD and XAFS. The active phase of Pd was a molecular Pd species whose structure was similar to PdCl₂, probably modified by a carbonyl ligand. The active phase of copper was found to be solid Cu₂Cl(OH)₃ particles. The presence of Cu was essential to keep the Pd in the Pd(II) state during the reaction.     

Kinetics of the transformation process of PbSO4 to PbO2 in a lead anodic film

The kinetics of the nucleation and growth of PbO₂ during the potentiostatic oxidation of PbSO₄ in a lead anodic film was studied using linear sweep voltammetry, potential-step and ac impedance tracing methods. The film investigated is the partially reduced anodic PbO₂ film formed by polarizing a lead electrode in 4.5 M H₂SO₄ solution first at 1.3 V vs. Hg|HgSO₄ for 20 min and then at 0.9 V for 5 min. The nucleation and growth process begins some time after the potential step and is completed within 60 s. The pre- and post-nucleation and growth processes correspond to the growth of the anodic film formed by the oxidation of the lead substrate. The mathematical equations representing the current-time and capacitance-time transients are derived taking the background oxidation current into account. The experimental results are well fitted by these equations. The process obeys the laws of two-dimensional instantaneous nucleation and growth.     

Synthesis and reactivity of [N(C6H4Br)3][B(C6F5)4]: the X-ray crystal structure of [Fe(C5H5)2][B(C6F5)4]

A new chemical oxidant [N(4-C₆H₄Br)₃][B(C₆F₅)₄], was prepared and used to synthesize [Fe(C₅H₅)₂][B(C₆F₅)₄]. The crystal structure of [Fe(C₅H₅)₂][B(C₆F₅)₄] was determined.     

阳极氧化法制备TiO2多孔薄膜

本文综述了制备TiO₂薄膜的各种方法,详细介绍了阳极氧化法制备TiO₂多孔膜的进展,在非含氟电解液体系中,对纯钛进行阳极氧化处理可制得表面呈无规则生长的多孔膜结构;在含氟电解液体系中,则可自组织形成高度有序的TiO₂纳米管阵列,并指出阳极氧化法是可在常温低压下进行、操作工艺简单、薄膜性能稳定、再现性好的一种最具工业化应用潜力的制备方法。     

Propane oxidation over Pd/LaFe0.8Co0.2O3 catalyst

Pd/LaFe_0.8Co_0.2O₃ was found to be more active than the Pd/Al₂O₃ catalyst in propane oxidation. Activity and the oxidation state of palladium were strongly affected by the redox ratio (S) of reactants. Higher propane conversion could be obtained under rich conditions at higher temperatures, contributing to steam reforming. The presence of excess steam would bring about inhibition and oscillation.     

n -Heptane oxidation over co3o4-ceo2 catalyst

The present study reports the catalytic behavior of Co₃O₄-CeO₂ in the oxidation of n-heptane. The results obtained showed that the catalyst give good activity in n-heptane oxidation with high selectivity to carbon dioxide. This revised version was published online in June 2006 with corrections to the Cover Date.     

Reducibility of Mo species in Pt/MoO3 and PtMo/Al2O3 catalysis

Recucibility of Mo species in Pt/MoO₃ and PtMo/Al₂O₃ has been investigated by temperature-programmed reduction (TPR), temperature-programmed desorption of hydrogen (H₂-TPD) and temperature programmed electronic conductivity (TPEC) techniques. In Pt/MoO₃ at H₂ atmosphere, it was found by TPEC and TPR that, a slight amount of Pt could activate the transfer of the species and H atoms between H₂ and MoO₃, and thus accelerate the reduction of MoO₃. In PtMo/Al₂O₃, TPR and H₂-TPD revealed that the reduction of surface Mo species could also be facilitated by Pt. Two kinds of hydrogen molybdenum species were proposed on the surface of the catalyst after prereduction.     

NixCo3-xO4表面修饰对CdSe/TiO2纳米管阵列光电化学氧化水活性的影响

利用氨挥发诱导法在CdSe/TiO2纳米管阵列表面负载一层NixCo3-xO4。采用SEM、XRD、XPS、UV-Vis对样品进行表征,通过线性扫描伏安法测定光阳极的释氧电势来评价其光电水氧化活性。结果表明:表面NixCo3-xO4是尖晶石结构;相对于CdSe/TiO2纳米管阵列光阳极,NixCo3-xO4/CdSe/TiO2光阳极能将光电氧化水的过电势降低430 mV。Ni离子的引入使得NixCo3-xO4表面富含三价阳离子(Ni3+,Co3+),从而促进CdSe/TiO2光阳极光电水氧化的进行。