Normal and differential demasking flow-injection manifold for the direct spectrophotometric determination of zinc(II) in biological materials and pharmaceutical formulations

A normal and a differential demasking flow-injection (FI) manifold were developed and optimized for the spectrophotometric determination of microamounts of Zn(II) in biological materials and pharmaceutical formulations. The reported method is very sensitive, rapid, simple and it is based upon the reaction of Zn(II) with 2,2'-dipyridyl-2-pyridylhydrazone (DPPH) in a strongly basic medium to form a yellow-coloured complex (lambda max = 448 nm). By using the differential demasking manifold, the tolerance of the method to many cations was enhanced by a mean factor of 25. The obtained calibration graphs were linear in the range of 0-10 mg l-1 Zn(II), at a sampling rate of 120 injections h-1 in both cases. The precisions of both manifolds were very good (RSD = 0.6 and 0.8%, respectively) and the 3 sigma detection limits were quite satisfactory (cL = 4 and 6 ng ml-1 respectively). The method has been successfully applied to the determination of Zn(II) in serum, human hair and pharmaceutical formulations with recoveries ranging between 98.0 and 101.6%. The obtained results were also in excellent agreement with flame atomic absorption spectrometry (FAAS), since the mean relative error was er = 0.9%.     

Determination of iodine and bromine in plasma and urine by inductively coupled plasma mass spectrometry

The simultaneous determination of iodine and bromine in plasma and urine by inductively coupled plasma mass spectrometry, using a Nermag prototype instrument, is described. The sample preparation involves only a 10-fold dilution with a diluent containing europium as an internal standard followed by direct nebulisation in the plasma. The iodine, bromine and europium ions are measured at m/z = 127, 79, and 153, respectively. The sensitivity of the method, with detection limits of 1.6 and 52 micrograms l-1 for iodine and bromine, respectively, is satisfactory for clinical applications. The calibration graphs were linear over the ranges 0-400 micrograms l-1 and 0-40 mg l-1 for iodine and bromine, respectively, which are wide enough for most assays. The recoveries were close to 100% with coefficients of variation of less than 3%. The within-day and between-day reproducibility was about 5%. The concentrations of iodine and bromine in the plasma of 26 healthy individuals were 58 +/- 12 micrograms l-1 and 4.1 +/- 0.9 mg l-1, respectively. The amounts of iodine and bromine eliminated in urine were 94 +/- 97 micrograms per 24 h (range 27-403 micrograms per 24 h) and 3.6 +/- 1.7 mg per 24 h, respectively. These results are in agreement with reported values.     

Determination of phenol at ng l-1 level by flow-injection chemiluminescence combined with on-line solid-phase extraction

In this paper, a simple flow-injection chemiluminescence (CL) system combined with on-line solid-phase extraction is presented to determine phenol. This method is based on the enhancement effect of phenol on the luminol-K3Fe(CN)6 CL system. The solid-phase extraction promised the high sensitivity and improved selectivity of CL detection. With the calibration range from 4.7 ng l-1 to 470 ng l-1 phenol concentration, the proposed method was applied to analyzing phenol in water samples and the obtained results were validated by the standard method. The detection limit was determined as 0.66 ng l-1. The relative standard deviation was 1.5% for determining 4.7 ng l-1 phenol standard (n=7).     

Studies on synthesis and application of XAD-4-salen chelate resin for separation and determination of trace elements by solid phase extraction

The use of chemically modified XAD-4-salen chelating resin had been studied for the separative concentration of metal ions from an aqueous solution. XAD-4-salen was synthesized by diazonium coupling reaction of salen[N,N′-bis(salicylidene)ethylenediamine] and Amberlite XAD-4 resin. The distribution coefficient at various pH values and adsorption capacities were obtained with respect to Cu(II), Pb(II) and Bi(III). Trace elements were pre-concentrated on the synthesized XAD-4-salen by batch method for atomic absorption spectrometric determination. Some conditions, such as the pH of aqueous solution, amount of XAD-4-salen, kinds and concentration of acids were optimized for the analytical application of XAD-4-salen. For the pre-concentration of metal ions, the pH of the aqueous solution was adjusted to approximately 5.5, and then it was stirred 30 min after the addition of 50 mg of pulverized XAD-4-salen. The adsorbed metal ions were desorbed by 10 mL of 1.0 M HNO₃. The desorption efficiency of Bi(III) was enhanced by the addition of 30 mg/L of Pd(II). The addition of Pd(II) as a matrix modifier could improve the reproducibility and sensitivity in the Atomic Absorption Spectroscopy (AAS) determination of volatile lead and bismuth. In the present study, this procedure has been applied for the determination of Cu(II), Pb(II) and Bi(III) in real samples of five kinds of river water, using a standard calibration curve method. Recoveries of 85–120% were obtained in the spiked samples in which given amount of analytes were added.     

Determination of Co(II) by chemiluminescence after in situ electrochemical pre-separation on a flow-through mercury film electrode

A novel method of electrochemical pre-separation of Co(II) before detection by chemiluminescence is reported together with the associated instrumentation. The Co(II) ions were selectively pre-separated on a mercury film electrode (MFE) by on-line reduction, then the accumulated metal was oxidised and selectively stripped back into the flowing solution as Co(II). These secondary ions were quantified as a result of their catalytic activity on the chemiluminescent reaction between luminol and hydrogen peroxide that was also induced on-line. The whole sequence was carried out in an automated flow-through system, in which the electrochemical pre-separation of metals was performed in either continuous flow or flow injection analysis (FIA) regimes. The scope of the method, both in terms of selectivity and sensitivity, has been demonstrated and the quantitative determination of Co(II) by the proposed method has been investigated. For a period of continuous flow pre-separation of 4 min, the calibration curve for Co(II) was linear up to a concentration of 100 micrograms l-1, the relative standard deviation was 4% at the 20 micrograms l-1 level and the limit of detection was 0.5 microgram l-1 (at the 3 sigma level). The method was applied to the determination of the cobalt content in a high purity iron sample.     

Mechanised flow system for on-line microwave digestion of food samples with off-line catalytic spectrophotometric determination of cobalt at ng l-1 levels

A mechanised system for on-line slurry food sample digestion was developed and an off-line cobalt determination was performed. The stabilised slurry sample was introduced into an air carrier stream until reaching the digestion coils located inside a household microwave oven. Software written in Visual Basic 3.0 was developed to permit the transport of the slurry samples and the programming of the microwave oven and also the control of the mineralization valve. The proposed system was optimized for determination of cobalt in certified samples such as mussels, bovine liver and fish and also uncertified fish samples. The digestion parameters were established as 3 mol l-1 HNO3 for mussels, 3 mol l-1 HNO3 plus 0.16% v/v H2O2 for bovine liver and 12 mol l-1 HNO3 for fish employing maximum power for 5 min of microwave actuation. In the subsequent spectrophotometric method for the catalytic determination of cobalt, the Tiron and hydrogen peroxide concentrations were 1.8 x 10(-3) and 3.0 x 10(-4) mol l-1, respectively, and the sample residence time was 300 s as determined by an optimisation process. The proposed method features a linear range from 10 to 200 ng l-1 Co (r > 0.996) with detection and quantification limits of 1.7 and 5.5 ng l-1 Co, respectively. The precision, expressed as RSD, was 2.4% (n = 12) for repeatability and 5.2% (n = 10) for reproducibility and the accuracy of the proposed method was assessed by using certified samples and an alternative technique (ETAAS).     

Determination of trichloroacetate in human serum and urine by ion chromatography

A simple and rapid ion chromatographic method has been developed for the determination of trichloroacetate in human serum and urine. Two short (50 x 5 mm i.d.) low-capacity anion-exchange resin columns in series were used as the analytical column and a mixture of 35 mM sodium hydroxide, 20 mM p-hydroxybenzonitrile and 2% V/V acetonitrile (pH 12.3) as the eluent. The calibration graph was rectilinear from 0.3 to 33 mg l-1 of trichloroacetate at 10 microS with a detection limit (3 sigma) of 0.08 mg l-1. The recovery of trichloroacetate, obtained by analysing spiked serum and urine samples, was in the range 98.2-101% and the coefficient of variation was always less than 3.0%.     

A method for the measurement of catechol-O-methyltransferase activity using norepinephrine, an endogenous substrate

We propose a highly sensitive method for the measurement of catechol-O-methyltransferase (COMT) activity with norepinephrine (NE), an endogenous native substrate. The product, normetanephrine, was determined by high-performance liquid chromatography (HPLC)-peroxyoxalate chemiluminescence reaction detection or, if required, less sensitive fluorescence detection. For the measurement of membrane-bound (MB)-COMT activity in the rat erythrocyte, the HPLC-peroxyoxalate chemiluminescence reaction detection was employed. Soluble (S)- and MB-COMT activities in the rat erythrocyte were 22.9 +/- 2.5 and 4.62 +/- 1.23 pmol min-1 (mg protein)-1, respectively (n = 5). The Km values obtained for S- and MB-COMT were 366 +/- 31 mumol l-1 and 12.0 +/- 1.1 mumol l-1, respectively (n = 5), suggesting that the use of NE as a substrate would give more precise information on the role of both isoenzymes. However, with dihydroxybenzoic acid as an artificial substrate, the Km values for S- and MB-COMT were similar, with values of 69.2 +/- 11.4 mumol l-1 and 72.2 +/- 9.2 mumol l-1, respectively. The proposed method is thought to be useful for the measurement of both S-COMT and MB-COMT activities, and would give us critical information on the role of metabolism of catecholamines in rat tissues.     

Optimization of solid-phase microextraction conditions using a response surface methodology to determine organochlorine pesticides in water by gas chromatography and electron-capture detection.

A response surface methodology was applied to optimise the solid-phase microextraction (SPME) conditions using a polyacrylate-coated fiber to determine thirteen organochlorine pesticides from water. Analyses were performed using gas chromatography-electron-capture detection. Variables affecting absorption in both the headspace and immersion extraction were optimised by using a response surface generated with a Doehlert design, and the results were compared. The immersion SPME method was selected since higher recoveries were obtained for most of the compounds studied. The method developed was applied to the analysis of tap and Ebro river water samples. The linear range of most pesticides for real samples was found to be between 0.001 and 2.5 micrograms l-1 and the limits of detection were between 0.15 and 0.35 ng l-1. The repeatability and the reproducibility between days of the method (n = 6), expressed as relative standard deviation, for tap water spiked at a level of 1 ng l-1 were between 5.7 and 25.6% and between 7.6 and 26.5%, respectively.     

离子液体中卤素离子杂质的离子色谱-直接电导检测法分析

研究了离子色谱-直接电导检测法分离测定离子液体中的卤素离子(F~-、Cl~-、Br~-)杂质.采用Shim-pack IC-A3阴离子交换色谱柱,考察了淋洗液种类及浓度、流速和色谱柱温度对分离测定的影响.最佳色谱条件为:以1.25 mmol/L邻苯二甲酸氢钾为淋洗液,流速1.5 mL/min,色谱柱温45 ℃.在此条件下可以基线分离卤素离子,且NO~-_3、BF~-_4、SO~(2-)_4不干扰测定.该法测定卤素离子的检出限(S/N=3)为0.02 ～0.11 mg/L,峰面积的相对标准偏差(n=5)不大于0.7%,F~-、Cl~- 和Br~- 的标准曲线的线性范围分别为0.1 ～50、0.1 ～50、0.5 ～100 mg/L.将方法用于烷基咪唑四氟硼酸盐离子液体中卤素离子杂质的测定,加标回收率为98% ～102%.     

Equilibrium, 1H and 13C NMR spectroscopy,and X-ray diffraction studies on the complexes Bi(DOTA)- and Bi(DO3A-Bu)

Several Bi(III) complexes are used in medicine as drugs. Bi(DO3A-Bu) has recently been proposed as a nonionic contrast agent in X-ray imaging (H(3)DO3A-Bu = 10-[2,3-dihydroxy-(1-hydroxymethyl)propyl]-1,4,7,10-tetraazacyclododecane-1,4,7,-triacetic acid). The solution equilibria and NMR structure and dynamics of Bi(DO3A-Bu) and of the similar Bi(DOTA)(-) have been investigated (H(4)DOTA = 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid). The stability constants were determined with the study of the competition equilibria between Br(-) ions and the ligands DOTA or DO3A-Bu for the Bi(III) by spectrophotometry. The stability constants, obtained for Bi(DOTA)(-) and Bi(DO3A-Bu), are very high, log K = 30.3 and 26.8, respectively. Potentiometric titrations indicated the dissociation of one of the protons among the three alcoholic OH groups in Bi(DO3A-Bu). The dissociation constant is log K = 7.53 (0.09) indicating that at physiological pH about 50% of the species possess -1 charge. It was shown by (1)H and (13)C NMR spectroscopy that the OH group attached to the middle carbon atom of the "butriol" side chain is coordinated to the Bi(III) and starts to deprotonate at pH > 5.5. The crystal structure of NaBi(DOTA).H(2)O shows an octacoordinated arrangement of the donor atoms around the Bi(III), with no water in the inner sphere. The crystals belong to the centrosymmetric space group C2/c. The temperature dependent (1)H and (13)C NMR spectra indicate that both Bi(DOTA)(-) and Bi(DO3A-Bu)(-) complexes are fluxional. For Bi(DOTA), the Delta(deltadeltadeltadelta) right harpoon over left harpoon Lambda(lambdalambdalambdalambda) fluxionality was identified, and on the basis of the activation parameters, a synchronous motion was suggested for the fluxional motion resulting in the change of ring conformation and of the helicity of the complex. The transition state is supposed to be more symmetrical than the initial state. The deprotonated Bi(DO3A-Bu) has a highly asymmetric NMR structure in solution, and its fluxional motion is slower than that of Bi(DOTA)(-).     

开叉毛细管HG-FAAS测定地质样品中的锑、铋

氢化物发生原子吸收法(HG-FAAS)广泛应用于冶金、地质、环境、医药和食品分析等领域中。研究表明,氢化物发生法的检出限、测定精度以及干扰等情况与原子化器和氢化物发生器的结构以及传输过程有关[1]。郭小伟等[2-4]研制了用于火焰原子吸收光谱分析的双毛细管喷雾器,并利用其测     

Synthesis and Efficiency of an Epoxy-Urea Chelating Resin for Preconcentrating and Separating Trace Bi,In, Sn,Zr, V And Ti From Solution Samples

Abstract

A new epoxy-urea chelating resin was synthesized from epoxy resin and used for the preconcentration and separation of trace Bi(III), In(III), Sn(IV), Zr(IV), V(V) and Ti(IV) ions from solution samples. The analyzed ions can be enriched at pH 5 at a flow rate of 1–4 ml/min, and can be also desorbed with 10 mL of 2 M HCl +0.1g NH₄F solution from the resin column, with recoveries over 97%. The chelating resin reused 6 times can still adsorb quantitatively the Bi, In, Sn, Zr, V and Ti ions, and eighty to thousand-fold excesses of Ca(II), Mg(II), Cu(II), Zn(II), Al(III), Sb(III), Ni(II), Mn(II) and Fe(III) cause little interference with the enrichment and determination of these ions. The RSDs of the proposed method for the determination of 500–50 ng/ml Bi, In and Sn, 50–5.0 ng/ml Zr, V and Ti were in the range of 0.4 ～ 4.0%, the enrichment factor of the resin for the ions is in the range of 10–100. The recoveries of added standard in waste water are between 96% and 100%, and the concentration of each ion in alloy steel sample determined by the method is in good agreement with the reference value analyzed by a steel plant with average error <2.8%.     

Fluorimetric determination of phytic acid based on the activation of the oxidation of 2,2'-dipyridyl ketone hydrazone catalysed by Cu(II)

Phytic acid exerts an activation effect on the oxidation of 2,2'-dipyridyl ketone hydrazone catalysed by Cu(II) ion and the oxidation product is highly fluorescent. A fixed time method for the fluorimetric determination of phytic acid based on this effect is described. The calibration graph is linear over the range 0.05-0.6 mg l-1 phytic acid, resulting in a limit of detection of 0.03 mg l-1 phytic acid. The relative standard deviation is in the range 1.4-1.8%, depending on the sample analysed. The method was successfully applied to the determination of phytic acid in human urine (20 samples) and food samples (nine different products). The results obtained for urine samples ranged from 0.31 to 3.6 mg l-1 phytic acid and for food samples from 3.8 to 22 mg g-1 phytic acid. This is the first procedure to be reported for the determination of phytic acid based on fluorimetric measurements.     

On-column amperometric detection of ofloxacin and pasiniazid in urine by capillary electrophoresis with an improved fractured joint and small detection cell

An improved high-voltage electric field isolating joint and small detection cell have been carefully designed and fabricated. The joint possesses short steady time, high electric conductance efficiency and high performance. The cell is convenient to install and remove the capillaries with and without the joint, as well as to fix, adjust and insert the microelectrode into the detection capillary. Using the joint and the cell, an analytical method for determination of ofloxacin (Oflx) and pasiniazid (Ipa) in urine by capillary electrophoresis with on-column amperometric detection was developed. The calibration lines were linear in the range of 10-100 mg l-1 of Oflx and 1.0-50 mg l-1 of Ipa, respectively. The detection limits were 8.5 mg l-1 of Oflx and 0.80 mg l-1 of Ipa. Their recovery ranged from 101 to 104%. The accuracy and intra-day and inter-day reproducibility of Oflx and Ipa were determined with satisfactory results. This method was successfully used for determining Oflx and Ipa in human urine.     

Urinary cotinine fluoroimmunoassay for smoking status screening adapted to an automated analyser.

A polarization fluoroimmunoassay for cotinine, a major metabolite of nicotine, has been adapted for fully automated screening of urine samples on the Abbott TDx analyser. The method has sensitivity and specificity suitable for the discrimination of active smokers from non-smokers (including passive smokers) by application of a cut-off at 0.5 mg l-1 of total urinary cotinine. Most active smokers' urine gave results over 1 mg l-1, whereas apparent levels in non-smokers were 0.08 mg l-1 or lower. A result for one sample can be obtained in about 5 min and a throughput of 80 samples h-1 can be maintained for large-scale screening applications.     

Determination of carbon dioxide and acid components in exhaust gas by suppressed ion chromatography.

Although anions are usually determined by suppressed ion chromatography (IC), carbonate and bicarbonate ions can not be determined, because a mixed solution of sodium carbonate and sodium hydrogencarbonate is used as the eluent. This paper describes an IC method for the determination of carbonate ion and common anions using an IonPac AG17/AS17 column, an EG 40 eluent generator and a conductivity detector. The proposed IC method could determine carbonate ion and anions within 6 min. The relative standard deviations (n = 5) for chloride (0.4 mg L(-1)), nitrite (0.8 mg L(-1)), carbonate (100 mg L(-1)), nitrate (1.0 mg L(-1)) and sulfate (2.0 mg L(-1)) ions were 5.1%, 1.1%, 4.2%, 5.1% and 1.1%, respectively. In addition, the absorbing solution of carbon dioxide was examined, and 2-amino-2-methyl-1-propanol was found to be a good absorbing solution. The proposed IC method was applied to the determination of carbon dioxide and acid components in flue gas and automobile exhaust gas.     

Properties and applications of polyacrylacylisothiourea chelating fiber for preconcentration and separation of trace titanium, vanadium and bismuth

An ICP-OES method using a new poly-acrylacylisothiourea chelating fiber to preconcentrate and separate trace Ti(IV), V(V) and Bi(III) ions from solution samples is established. The results show that 5–25 ng/ml of Ti or V and 50–250 ng/ml of Bi ions in 200–1000 ml of solution can be enriched quantitatively by 0.05 g of the fiber at pH 3 with recoveries over 97%. These ions can be desorbed quantitatively with 10 ml of 4M HC1O₄. 100- to 1000-fold excesses of Fe(III), Al(III), Ca(II), Mg(II), Cu(II), Ni(II) and Mn(II) ions cause little interference. The chelating fiber stored for about 2 years can still be used repeatedly for preconcentration and separation of trace Ti, V and Bi ions from solution with above 95% recovery. The RSDs for enrichment and determination of 5 ng/ml of Ti or V and 50 ng/ml of Bi are in the range 2.5–2.8%. The recoveries of added standard in real waste waters and mineral samples are between 96 and 100%, and the concentration found for each ion in the mineral sample was in good agreement with that measured by ETAAS.     

Evaluation and application of bismuth as an internal standard for the determination of lead in wines by simultaneous electrothermal atomic absorption spectrometry

A method for the direct determination of Pb in wines by simultaneous multi-element atomic absorption spectrometry (SIMAAS) using a transversely heated graphite atomizer, Zeeman-effect background corrector and internal standardization is proposed. Bismuth was used as an internal standard and Pd(NO3)2 plus Mg(NO3)2 as chemical modifier to stabilize both the analyte and the internal standard. The implementation of two pyrolysis steps avoided any build-up of carbonaceous residues on the graphite platform. All diluted samples (1 + 1 v/v) in 0.2% v/v HNO3 and reference solutions (5.0-50 microg l(-1) Pb in 0.2% v/v HNO3) were spiked with 25 microg l(-1) Bi. For a 20 microl aliquot dispensed into the graphite tube, a good correlation (r = 0.9997) was obtained between the ratio of the analyte signal to the internal standard signal and the analyte concentration of the reference solutions. The electrothermal behaviour of Pb and Bi in red, white and rosé wines were compared. In addition, absorbance variations due to changes in experimental conditions, such as atomizer temperature, integration time, injected sample volume, radiation beam intensity, graphite tube surface, dilution and sample composition, were minimized by using Bi as internal standard. Relative standard deviations of measurements based on integrated absorbance varied from 0.1 to 3.4% and from 0.5 to 7.3% (n = 12) with and without internal standard correction, respectively. Good recoveries (91-104%) for Pb spikes were obtained. The characteristic mass was 45 pg Pb and the limit of detection based on integrated absorbance was 0.9 microg l(-1) Pb. Internal standardization increased the lifetime of the tube by 25%. Direct determinations of Pb in wines with and without internal standardization approaches were in agreement at the 95% confidence level. The repeatability and the tube lifetime were improved when using Bi as internal standard. The improvement in accuracy using an internal standard was only observed when the analytical results were affected by errors.     

Simultaneous determination of arsenic, antimony, bismuth and mercury in geological materials by vapor generation-four-channel non-dispersive atomic fluorescence spectrometry

Chemical vapor generation (CVG) coupled with non-dispersive atomic fluorescence spectrometry (NDAFS) has been widely used for determination of vapor-forming elements, but most of such works have been focused on single element analysis, and reports dealing with more than three elements simultaneous determination by CVG-NDAFS are rare. In this work, a sensitive and robust analytical procedure for the simultaneous determination of arsenic, antimony, bismuth and mercury in geological materials using vapor generation-four-channel non-dispersive atomic fluorescence spectrometry has been developed. The conditions of instrumentation and vapor generation of arsenic, antimony, bismuth and mercury were optimized. The optimized concentrations of KBH(4) and HCl required for analytes generation were 1.3% (m/v) and 20% (v/v), respectively. The interferences of coexisting ions and mutual hydride interferences were investigated carefully. One thousand milligrams per litre of Fe(3+); 500mgl(-1) of Pb(2+), Zn(2+), Mn(2+); 50mgl(-1) Cu(2+), Ni(2+), Cr(6+), Co(2+); 10mgl(-1) Ag(+) and 5mgl(-1) Au(3+) does not interfere with the determination of As, Sb, Bi and Hg. Associating a dilution of 1:250 (m/v) in the procedure of sample pretreatment, the tolerant concentrations of As, Sb, Bi and Hg in real geological materials are 2500, 1000, 250 and 5000ppm, respectively. Under optimal conditions, the detection limits for As, Sb, Bi and Hg were determined to be 0.068, 0.047, 0.037 and 0.008ngml(-1), respectively. The precisions for seven replicate determinations at the 5ngml(-1) of As, Sb, Bi and 1ngml(-1) of Hg were 0.47, 0.60, 0.97 and 0.93% (R.S.D.), respectively. Sample digestion was carried out on 500mg sample with 3ml HNO(3) and 10ml HCl, followed by addition of thiourea solution for the quantitative reduction of As(V), Sb(V) to As(III), Sb(III). The proposed method was successfully applied to the simultaneous determination of As, Sb, Bi and Hg in a series of certified geological reference materials using simple aqueous standard calibration technique. The results obtained are in good agreement with the certified values.