Improving the electrical conductivity of CuCrO2 thin film by N doping

N-doped CuCrO₂ thin films were prepared by using radio frequency magnetron sputtering technique. The XRD and XPS measurements were used to confirm the existence of the N acceptors in CuCrO₂ thin films. Hall measurements show the p-type conduction for all films. The electrical conductivity increases rapidly with the increase in N doping concentration, and the maximum of the electrical conductivity of 17 S cm⁻¹ is achieved for the film deposited with 30 vol.% N₂O, which is about three orders of magnitude higher than that of the undoped CuCrO₂ thin film. Upon increasing the doping concentrations the band gaps of N-doped CuCrO₂ thin films increase due to the Burstein-Moss shift.     

Chemical spray pyrolysis deposition and characterization of p-type CuCr1−xMgxO2 transparent oxide semiconductor thin films

A chemical spray pyrolysis technique for deposition of p-type Mg-doped CuCrO₂ transparent oxide semiconductor thin films using metaloorganic precursors is described. As-deposited films contain mixed spinel CuCr₂O₄ and delafossite CuCrO₂ structural phases. Reduction in spinel CuCr₂O₄ fraction and formation of highly crystalline films with single phase delafossite CuCrO₂ structure is realized by annealing at temperatures ?700 °C in argon. A mechanism of synthesis of CuCrO₂ films involving precursor decomposition, oxidation and reaction between constituent oxides in the spray deposition process is presented. Post-annealed CuCr_0.93Mg_0.07O₂ thin films show high (?80%) visible transmittance and sharp absorption at band gap energy with direct and indirect optical band gaps 3.11 and 2.58 eV, respectively. Lower (∼450 °C) substrate temperature formed films are amorphous and yield lower direct (2.96 eV) and indirect (2.23 eV) band gaps after crystallization. Electrical conductivity of CuCr_0.93 Mg_0.07O₂ thin films ranged 0.6-1 S cm⁻¹ and hole concentration ∼2×10¹⁹ cm⁻³ determined from Seebeck analysis. Temperature dependence of conductivity exhibit activation energies ∼0.11 eV in 300-470 K and ∼0.23 eV in ?470 K region ascribed to activated conduction and grain boundary trap assisted conduction, respectively. Heterojunction diodes of the structure Au/n-(ZnO)/p-(CuCr_0.93Mg_0.07O₂)/SnO₂ (TCO) were fabricated which show potential for transparent wide band gap junction device.     

Surface textured ZnO:Al thin films by pulsed DC magnetron sputtering for thin film solar cells applications

Transparent conducting thin films of ZnO:Al (Al-doped ZnO, AZO) were prepared via pulsed DC magnetron sputtering with good transparency and relatively lower resistivity. The AZO films with 800 nm in thickness were deposited on soda-lime glass substrates keeping at 473 K under 0.4 Pa working pressure, 150 W power, 100 μs duty time, 5 μs pulse reverse time, 10 kHz pulse frequency and 95% duty cycle. The as-deposited AZO thin films has resistivity of 6.39 × 10⁻⁴ Ω cm measured at room temperature with average visible optical transmittance, T_total of 81.9% under which the carrier concentration and mobility were 1.95 × 10²¹ cm⁻³ and 5.02 cm² V⁻¹ s⁻¹, respectively. The films were further etched in different aqueous solutions, 0.5% HCl, 5% oxalic acid, 33% KOH, to conform light scattering properties. The resultant films etched in 0.5% HCl solution for 30 s exhibited high T_total = 78.4% with haze value, H_T = 0.1 and good electrical properties, ρ = 8.5 × 10⁻⁴ Ω cm while those etched in 5% oxalic acid for 150 s had desirable H_T = 0.2 and relatively low electrical resistivity, ρ = 7.9 × 10⁻⁴ Ω cm. However, the visible transmittance, T_total was declined to 72.1%.     

Origin of ohmic behavior in Ni, Ni2Si and Pd contacts on n-type SiC

Ni, Ni₂Si and Pd contacts were prepared on n-type 4H-SiC and annealed in the temperature range of 750-1150 °C. The annealed contacts were analyzed before and after acid etching, and different features were found in unetched and etched contacts. Carbon left on the SiC surface after the acid etching of Ni₂Si contacts annealed at 960 °C was highly graphitized. In nickel contacts, the graphitization of interface carbon began at 960 °C and increased after annealing at higher temperatures. In palladium contacts, the onset of the interface carbon graphitization was observed after annealing at 1150 °C. For all three types of metallization, the minimal values of contact resistivity were achieved only when the sharp first-order peak at 1585 cm⁻¹ and distinct second-order peak at ∼2700 cm⁻¹ related to the presence of graphitized carbon were detected by Raman spectroscopy after the acid etching of contacts. The properties of unannealed secondary contacts deposited onto etched primary contacts were similar to the properties of the primary contacts unless carbon was selectively etched. The results show that ohmic behavior of Ni-based and Pd contacts on n-type SiC originates from the formation of graphitic carbon at the interface with SiC.     

Electrochemical corrosion behaviors of a-C:H and a-C:NX:H films

The a-C:H and a-C:N_X:H films were deposited onto silicon wafers using radio frequency (rf) plasma enhanced chemical vapor deposition (PECVD) and pulsed-dc glow discharge plasma CVD, respectively. Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) were used to characterize chemical nature and bond types of the films. The results demonstrated that the a-C:H film prepared by rf-CVD (rf C:H) has lower I_D/I_G ratio, indicating smaller sp² cluster size in an amorphous carbon matrix. The nitrogen concentrations of 2.9 at.% and 7.9 at.% correspond to carbon nitride films prepared with rf and pulse power, respectively.Electrochemical corrosion performances of the carbon films were investigated by potentiodynamic polarization test. The electrolyte used in this work was a 0.89% NaCl solution. The corrosion test showed that the rf C:H film exhibited excellent anti-corrosion performance with a corrosion rate of 2 nA cm⁻², while the carbon nitride films prepared by rf technique and pulse technique showed a corrosion rate of 6 nA cm⁻² and 235 nA cm⁻², respectively. It is reasonable to conclude that the smaller sp² cluster size of rf C:H film restrained the electron transfer velocity and then avoids detriment from the exchange of electrons.     

Optical and gas sensing properties of thick TiO2 films grown by laser deposition

In this work the optical and the gas sensing properties of thick TiO₂ waveguide films, produced by pulsed laser deposition, were investigated by m-line spectroscopy. The films were deposited on (0 0 1) SiO₂ substrates at temperature of 100 °C. The thickness of the films was measured to be in the range from 650 to 1900 nm and the roughness increases from 5 to 14.6 nm. High quality mode spectra, consisted of thin and bright TE and TM modes, were observed in the films with thickness up to 1200 nm. All the films revealed anisotropic optical properties. Gas sensitivity of the films to CO₂ was examined at room temperature on the basis of the variations of the refractive index. CO₂ concentration of 3 × 10⁴ ppm was detected, which corresponds to a refractive index variation of about 1 × 10⁻⁴. The crystal structure and the optical transmittance of the films were also presented and discussed.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

Characterization of Y2O3 gate dielectric on n-GaAs substrates

Physical and electrical properties of sputtered deposited Y₂O₃ films on NH₄OH treated n-GaAs substrate are investigated. The as-deposited films and interfacial layer formation have been analyzed by using X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). It is found that directly deposited Y₂O₃ on n-GaAs exhibits excellent electrical properties with low frequency dispersion (<5%), hysteresis voltage (0.24 V), and interface trap density (3 × 10¹² eV⁻¹ cm⁻²). The results show that the deposition of Y₂O₃ on n-GaAs can be an effective way to improve the interface quality by the suppression on native oxides formation, especially arsenic oxide which causes Fermi level pinning at high-k/GaAs interface. The Al/Y₂O₃/n-GaAs stack with an equivalent oxide thickness (EOT) of 2.1 nm shows a leakage current density of 3.6 × 10⁻⁶ A cm⁻² at a V_FB of 1 V. While the low-field leakage current conduction mechanism has been found to be dominated by the Schottky emission, Poole-Frenkel emission takes over at high electric fields. The energy band alignment of Y₂O₃ films on n-GaAs substrate is extracted from detailed XPS measurements. The valence and conduction band offsets at Y₂O₃/n-GaAs interfaces are found to be 2.14 and 2.21 eV, respectively.     

Synthesis and characterization of silicon carbonitride films by plasma enhanced chemical vapor deposition (PECVD) using bis(dimethylamino)dimethylsilane (BDMADMS), as membrane for a small molecule gas separation

Silicon carbonitride thin films have been deposited by plasma enhanced chemical vapor deposition (PECVD) from bis(dimethylamino)dimethylsilane (BDMADMS) as a function of X = (BDMADMS/(BDMADMS + NH₃)) between 0.1 and 1, and plasma power P (W) between 100 and 400 W. The microstructure of obtained materials has been studied by SEM, FTIR, EDS, ellipsometrie, and contact angle of water measurements. The structure of the materials is strongly depended on plasma parameters; we can pass from a material rich in carbon to a material rich in nitrogen. Single gas permeation tests have been carried out and we have obtained a helium permeance of about 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ and ideal selectivity of helium over nitrogen of about 20.     

Reactive ion etching of FePt using inductively coupled plasma

We propose a reactive ion etching (RIE) process of an L1₀-FePt film which is expected as one of the promising materials for the perpendicular magnetic recording media. The etching was carried out using an inductively coupled plasma (ICP) RIE system and an etching gas combination of CH₄/O₂/NH₃ was employed. The L1₀-FePt films were deposited on (1 0 0)-oriented MgO substrates using a magnetron sputtering system. The etching masks of Ti were patterned on the FePt films lithographically. The etch rates of ∼16 and ∼0 nm/min were obtained for the FePt film and the Ti mask, respectively. The atomic force microscopy (AFM) analyses provided the average roughness (R_a) value of 0.95 nm for the etched FePt surface, that is, a very flat etched surface was obtained. Those results show that the highly selective RIE process of L1₀-FePt was successfully realized in the present study.     

Transparent conducting Sn-doped Ga1.4In0.6O3 films prepared on α-Al2O3 (0 0 0 1) by MOCVD

Sn-doped Ga_1.4In_0.6O₃ films have been prepared on α-Al₂O₃ (0 0 0 1) substrates by the metalorganic chemical vapor deposition (MOCVD) method. The Sn-doping was varied from 0% to 7% (atomic ratio). Polycrystalline films with resistivity of 4.9 × 10⁻³Ω cm, carrier concentration of 5.9 × 10¹⁹ cm⁻³ and Hall mobility of 21.4 cm² v⁻¹ s⁻¹ was obtained at 5 at.% of Sn concentration. The average transmittance for the Sn-doped Ga_1.4In_0.6O₃ films in the visible range was over 90%. The bandgap of the films varies from 3.85 to 4.21 eV.     

Effects of co-substitution on the electrical properties of BiFeO3 thin films prepared by chemical solution deposition

Ferroelectric BiFeO₃ thin films with Nd-Cr (or Sm-Cr) co-substitution (denoted by BNdFCr and BSmFCr, respectively) were deposited on the Pt(2 0 0)/TiO₂/SiO₂/Si(1 0 0) substrates by a chemical solution deposition method. X-ray diffraction patterns revealed the formation of BNdFCr and BSmFCr thin films without any secondary phases. The co-substituted BNdFCr (or BSmFCr) thin films, which were annealed at 550 °C for 30 min in N₂ atmosphere, exhibited enhanced electrical properties compared to BFO thin films with the remanent polarization (2P_r) and coercive electric field (2E_c) of 196, 188 μC/cm² and 600, 570 kV/cm with the electric field of 800 kV/cm, respectively. The leakage current densities of BNdFCr and BSmFCr thin films measured at room temperature were approximately three orders of magnitude lower than that of BFO thin film, and the leakage current at room temperature of the thin films exhibited three distinctive conduction behaviors. Furthermore, the values of pulse polarizations [i.e., +(P*-P^{^}) or −(P*-P^{^})] of BNdFCr and BSmFCr thin films were reasonably unchanged up to 1.4 × 10¹⁰ switching cycles.     

Preparation and characterization of the amorphous tungsten cone field emitter arrays by Ar etching

Uniform amorphous tungsten cone arrays in high density were fabricated by Ar⁺ reduction etching of WO₃ nanowire film. The etching process was performed in the analysis chamber of an X-ray photoelectron spectroscopy (XPS) system. SEM and TEM results revealed that the tip radius of the etched cones was 10 nm, and the cones were amorphous with a high aspect ratio of over 250. XPS analysis proved the cones to be metallic tungsten. In the aspect of field-emission property, the tungsten cone arrays had a lower turn-on field of 3 MV m⁻¹ compared with 5 MV m⁻¹ of the as-grown original WO₃ nanowire film.     

Characterization of single-crystalline In2O3 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

Epitaxial In₂O₃ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates by metalorganic chemical vapor deposition (MOCVD). The films were deposited at different substrate temperatures (450-750 °C). The film deposited at 650 °C has the best crystalline quality, and observation of the interface area shows a clear cube-on-cube epitaxial relationship of In₂O₃(1 0 0)||YSZ(1 0 0) with In₂O₃[0 0 1]||YSZ[0 0 1]. The Hall mobility of the single-crystalline In₂O₃ film deposited at 650 °C is as high as 66.5 cm² V⁻¹ s⁻¹ with carrier concentration of 1.5 × 10¹⁹ cm⁻³ and resistivity of 6.3 × 10⁻³ Ω cm. The absolute average transmittance of the obtained films in the visible range exceeds 95%.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Effect of H2 and O2 plasma etching treatment on the surface of diamond-like carbon thin film

In this study, we investigated the surface properties of diamond-like carbon (DLC) films for biomedical applications through plasma etching treatment using oxygen (O₂) and hydrogen (H₂) gas. The synthesis and post-plasma etching treatment of DLC films were carried out by 13.56 MHz RF plasma enhanced chemical vapor deposition (PECVD) system. In order to characterize the surface of DLC films, they were etched to a thickness of approximately 100 nm and were compared with an as-deposited DLC film. We obtained the optimum condition through power variation, at which the etching rate by H₂ and O₂ was 30 and 80 nm/min, respectively. The structural and chemical properties of these thin films after the plasma etching treatment were evaluated by Raman and Fourier transform infrared (FT-IR) spectroscopy. In the case of as-deposited and H₂ plasma etching-treated DLC film, the contact angle was 86.4° and 83.7°, respectively, whereas it was reduced to 35.5° in the etching-treated DLC film in O₂ plasma. The surface roughness of plasma etching-treated DLC with H₂ or O₂ was maintained smooth at 0.1 nm. These results indicated that the surface of the etching-treated DLC film in O₂ plasma was hydrophilic as well as smooth.     

BiFeO3/Zn1−xMnxO bilayered thin films

BiFeO₃/Zn_1−xMn_xO (x = 0-0.08) bilayered thin films were deposited on the SrRuO₃/Pt/TiO₂/SiO₂/Si(1 0 0) substrates by radio frequency sputtering. A highly (1 1 0) orientation was induced for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO thin films demonstrate diode-like and resistive hysteresis behavior. A remanent polarization in the range of 2P_r ∼ 121.0-130.6 μC/cm² was measured for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO (x = 0.04) bilayer exhibits a highest M_s value of ∼15.2 emu/cm³, owing to the presence of the magnetic Zn_0.96Mn_0.04O layer with an enhanced M_s value.     

The ν12 band of C2D4

The Fourier transform infrared (FTIR) absorption spectrum of the ν₁₂ fundamental band of ethylene-d₄ (C₂D₄) was recorded in the 1017-1137 cm⁻¹ region with an unapodized resolution of 0.0063 cm⁻¹. Upper state (v₁₂ = 1) rovibrational constants consisting of three rotational and five quartic constants were improved by assigning and fitting 2103 infrared transitions using Watson’s A-reduced Hamiltonian in the I^r representation. The band centre of the A-type ν₁₂ band is found to be 1076.98480 ± 0.00002 cm⁻¹. The present analysis covering a wider wavenumber range and higher J and K_c values yielded upper state constants including the band centre which are more accurate than previously reported. The rms deviation of the upper state fit is 0.00045 cm⁻¹. Improved ground state rovibrational constants were also determined from the fit of 1247 ground state combination differences (GSCD) from the presently-assigned infrared transitions of the ν₁₂ band of C₂D₄. The rms deviation of the GSCD fit is 0.00049 cm⁻¹. In the rovibrational analysis, local frequency perturbations were not detected even at high J and K_a values. The calculated inertial defect Δ₁₂ is 0.32551 ± 0.00001 μŲ. The line intensities of the individual transitions in the ν₁₂ band were measured and the band strength of 39.8 ± 2.0 cm⁻² atm⁻¹ was derived for the ν₁₂ band of C₂D₄.     

Influence of the substrate material on the properties of pulsed laser deposited thin Li1+xMn2O4−δ films

Thin Li_1+xMn₂O_4−δ films were deposited on several substrate materials (stainless steel, p-doped silicon and glassy carbon) by pulsed laser deposition. To obtain the correct thin film stoichiometries, targets with a different amount of excess lithium were required (Li_1.03Mn₂O₄ + xLi₂O; x = 2.5 and 7.5 mol%). The resulting polycrystalline thin films were characterized with respect to their morphology and electrochemical activity. It was found that only thin Li_1+xMn₂O_4−δ films deposited on stainless steel and glassy carbon showed the typical insertion and deinsertion peaks of Li⁺ during cycling.     

Effects of thermal oxidation temperature on vacuum evaporated tin dioxide film

In order to investigate the effect of thermal oxidation temperature on tin dioxide (SnO₂), tin dioxide films were obtained on quartz substrates by vacuum evaporation of tin metal. The films were characterized by X-ray diffraction (XRD) analyses, scanning electron microscopy (SEM), temperature dependent electrical resistivity measurement and optical absorption spectroscopy. The SEM images showed that the films are dense, continuous and are composed of nanoparticles and particle sizes are increased after thermal oxidation. From the X-ray measurement results, the films indicated two strong reflection peaks of tetragonal structure in the orientations of (1 0 1) and (2 0 0) at 2θ = 33.89° and 37.95°, respectively. Intensity of the peaks increased with increasing thermal oxidation temperature. We found resistivity values of about 10⁻⁴ Ω-cm. Optical absorption spectra of the films in the UV–Vis spectral range revealed that optical band gap (E_g) value of the films increases with increasing thermal oxidation temperature.