Preparation of dendritic‐like CdS by hydrothermal method and its photocatalytic performance

In this article, dendritic‐like CdS has been prepared by a hydrothermal method using thiourea as the sulfur source, and the effects of experimental conditions on the morphologies of CdS have been investigated. The performances of CdS have been analyzed by X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and the fluorescence and photodegradation properties of CdS have also been investigated. The XRD result indicates that the dendritic‐like CdS are of hexagonal phase and they are highly crystallized. Also, the FESEM results show that the ratio of raw material affects the yield of CdS, the reaction time affects the morphology of CdS. The best morphology of CdS is dendritic structures and the length is about 6 μm. The fluorescence spectrum shows three peaks at 470 nm, 513 nm and 547 nm, which indicates that the dendritic‐like CdS mainly emits green and blue fluorescence. Moreover, the dendritic‐like CdS exhibits good photocatalytic activity and its photodegradation rate to methylene blue can reach 92%. The growth mechanism for the formation of CdS with dendritic structure is also described.     

PbS microcrystals with a magic‐square‐like structure prepared by a simple hydrothermal method

PbS microcrystals with a magic‐square‐shaped structure were successfully fabricated via a simple hydrothermal route, employing (CH₃COO)₂Pb and Na₂S₂O₃ as the lead and sulfur source without the assistance of any surfactant or template. S₂O₃^2‐ ions acted not only a supplier of S^2‐ ions but also a coordinating reagent. The formation of the above morphology was the direct result of the coordination between thiosulfate ions and lead ions. Researches indicated that the different synthetic approach could influence the morphology of the final product. A possible formation mechanism was suggested. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Hydrothermal synthesis of anatase flower‐like nanostructures for photocatalytic degradation of dye

Flower‐like hierarchical nanostructures of titanium dioxide (TiO₂) have been synthesized in large scale by a facile and controlled hydrothermal and after annealing process. The morphologies of flower‐like hierarchical nanostructures are formed by self‐organization of several tens of radially distributed thin flakes with a thickness of several nanometers holding a larger surface area. The materials are characterized by Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X‐ray diffraction (XRD). The ultraviolet photocatalytic degradation of R6G dyes has been studied over this flower‐like hierarchical nanostructures and the activity is compared with that of commercial P25 TiO₂ under same conditions. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Facile morphology‐controlled hydrothermal synthesis of flower‐like self‐organized ZnO architectures

Flower‐like self‐organized crystalline ZnO architectures were obtained through a facile and controlled hydrothermal process. As‐synthesized products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), high‐resolution transmission electron microscopy (HRTEM), X‐ray diffraction (XRD), electron diffraction and UV‐Vis spectroscopy. XRD and electron diffraction results confirmed the obtained materials are pure wurtzite ZnO. The effects of different ratios of starting materials and solvent on the morphologies of ZnO hydrothermal products were also evaluated by SEM observations. It is suggested that the use of water, rather than ethanol as the solvent, as well as employing a precursor of Zn(Ac)₂ and 2NaOH (v/v) in hydrothermal reactions are responsible for the generation of specific flower‐like self‐assembled ZnO structures. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

One‐step green synthesis by organic molten salt method and optical properties of CdS nanosheets

Cadmium sulfide (CdS) nanosheets were synthesized by an environment friendly, “green” organic molten salt (OMS) method at 220 °C. The as‐synthesized products were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), Transmission electron microscopy (TEM) and energy dispersive spectroscopy (EDS), respectively. The XRD results reveal that the as‐synthesized CdS nanosheets are of the hexagonal wurtzite structure and the CdS nanosheets grow along the c‐axis. The SEM results indicate that the diameters and thickness of the CdS nanosheets are about 20–40 nm and 5–10 nm, respectively. The optical properties of the CdS nanosheets were investigated by ultraviolet–visible (UV‐Vis) spectroscopy and photoluminescence (PL) spectroscopy. The ultraviolet–visible spectrum exhibits two excitonic peaks with a step‐like absorption and the photoluminescence spectrum shows a green emission peak centered at around 524 nm. A possible growth mechanism of CdS nanosheets was discussed.     

Optical and Photocatalytic properties of Mn‐doped CuO nanosheets prepared by hydrothermal method

Mn‐doped CuO nanosheets were prepared through a hydrothermal method to enhance their photocatalytic property. The structural and morphological features were monitored by using X‐Ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) with energy dispersive spectroscopy (EDS). UV‐vis absorption spectra showed the enhance absorption performance both in UV and visible light region. The band gaps were also calculate and the minimum value was 1.25 eV. The photocatalytic activity was investigated by the degradation of methylene blue (MB), which indicated that the photoactivity of samples depended on the amount of Mn²⁺ incorporated into the CuO lattice. The improved performance of photocatalysts can be attributed to enhanced light absorption and lower electron‐hole recombination.     

Optical studies on ZnO films prepared by sol‐gel method

A standard sol‐gel method was used to deposit ZnO thin films of suitable thickness on glass substrate.The optical characteristics of the visible to infrared range on thermal stress were critically observed. Morphological signature of the films was detected by X‐ray diffraction (XRD) and the crystallite size determined by Scherrer method from XRD data were consistent with grain size estimated from spectroscopic data through Meulenkamp equation. The optical band gap value from the transmission spectrum was found to corroborate with the existing works. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Multi‐factors on photocatalytic properties of Y‐doped Bi2WO6 crystallites prepared by microwave‐hydrothermal method

Different contents of Y‐doped Bi₂WO₆ crystallites were synthesized by a microwave‐hydrothermal method. The photocatalytic properties with different contents of Y‐doped Bi₂WO₆ crystallites were studied. The Y‐doped Bi₂WO₆ crystallites were also characterized by XRD, EDX, SEM and UV‐vis DRS and the multi‐factors on photocatalytic properties of Y‐Doped Bi₂WO₆ crystallites were discussed. The results indicate that Y³⁺ replacing Bi³⁺ enters into the Bi₂WO₆ lattice, producing a degree of Bi₂WO₆ lattice distortion. It also has an impact on the crystallinity of Bi₂WO₆ and the band gap is from 2.49 eV to 2.71 eV. The photocatalytic results show that when the content of Y doping becomes 10%, the degradation rate of rhodamine B is above 90% after 40 min irradiation, which shows that doping the proper rare earth ions is conducive to the photocatalytic properties of Bi₂WO₆ crystallites.     

Characterization and growth of CdS nanoparticles by a cost effective chemical reduction method

A simple chemical reduction method is followed to grow CdS nanoparticles at room temperature with different duration of time. The grown samples are ultrasonicated in ethanol. The dispersed samples are characterized using electron diffraction techniques. Simultaneously optical absorption, photoluminescence and longtime photorelaxation of these samples are studied at room temperature. An increase in band gap is observed in each case as compared to bulk CdS. Also particle size increases with increase of growth time and hence there is decrease of band gap with increase of growth duration. Simultaneously long time relaxation increases with increase of growth time. An attempt is made to correlate the structural, optical, electrical and opto‐electrical properties. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis of flake‐like crystals by a hydrothermal process

In this study, a hydrothermal method for formation of flake‐like nanocrystals is described. This approach with appropriate surfactant CTAB can be successfully synthesized of compound, noble metals, and semiconductors simple substance, such as lead sulfate, gold and selenium. The products were characterized by SEM image and XRD pattern. The results show that TSA acting as a new class of inorganic scaffolds for the synthesis of materials in crystal engineering and composites design for different applications is versatile reactor and may be extended to the creation of other highly novel inorganic structures with applications in catalysis, novel optical materials and other fields. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microstructural,optical and electrical properties of GeO2 thin films prepared by sol‐gel method

GeO₂ thin films were prepared by sol‐gel method on ITO/Glass substrate. The electrical and optical properties and the microstructures of these films were investigated with special emphasis on the effects of an annealing treatment in ambient air. The films were annealed at various temperatures from 500 °C to 700 °C. Structural analysis through X‐ray diffraction (XRD) and atomic force microscope (AFM) showed that surface structure and morphological characteristics were sensitive to the treatment conditions. The optical transmittance spectra of the GeO₂/ITO/Glass were measured using a UV‐visible spectrophotometer. All films exhibited GeO₂ (101) orientation perpendicular to the substrate surface where the grain size increased with increasing annealing temperature. The optical transmittance spectroscopy further revealed high transparency (over 70 %) in the wave range 400 – 800 nm of the visible region. At an annealing temperature level of 700 °C, the GeO₂ films were found to possess a leakage current density of 1.31×10^‐6A/cm² at an electrical field of 20 kV/cm. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and photoluminescence properties of bundle‐like CdS nanostructures assembled by high‐quality nanorods

Bundle‐like cadmium sulfide (CdS) nanostructures assembled by high‐quality nanorods have been successfully synthesized on a large scale via a facile solvothermal route in a mixed solvent of ethylenediamine and dodecanethiol. The typical lengths of bundle‐like CdS nanostructures are several tens of micrometers, and the diameters and lengths of CdS nanorods are about 50–70 nm and several micrometers, respectively. The influence of the concentration of dodecanethiol on the morphologies of CdS nanostructures has been investigated carefully. Photoluminescence spectra (PL) of CdS nanostructures reveal that the bundle‐like CdS nanostructures exhibited two fluorescence emission peaks centered at 495nm (2.51 eV) and 522 nm (2.38 eV) as the excitation wavelength is 405 nm. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Facile synthesis of pencil‐like ZnO nanostructures at low temperature

Pencil‐like ZnO nanostructure was synthesized by directly oxidizing granular Zn films, which was thermal deposited in a nitrogen atmosphere from Zn powder in a horizontal tube furnace. The formation of the pencil‐like structure, including a hexagonal rod and a sharp tip with diameter about 60 nm, highly depend on the thickness of the initial zinc film and the temperature of the oxidizing process. ZnO nanorods were formed in a relatively low temperature, while thicker zinc film was apt to form a dense ZnO film with tubular structures. The different structured ZnO materials showed distinguishing optical properties which indicate the intrinsic defects forming in the different growth conditions. The pencil‐like ZnO structures exhibit a relatively strong green emission attributed to the high concentrations of oxygen vacancies and its taper tip has great prospects in field‐emission devices.     

Structure and optical properties of Mg‐doped ZnO nanoparticles by polyacrylamide method

Mg‐doped ZnO (Mg_xZn_1‐xO) nanoparticles with precise stoichiometry are synthesized through polyacrylamide polymer method. Calcination of the polymer precursor at 650 °C gives particles of the homogeneous solid solution of the (Mg_xZn_1‐xO) system in the composition range (x < 0.15). ZnO doping with Mg causes shrinkage of lattice parameter c. The synthesized Mg_xZn_1‐xO nanoparticles are typically with the diameter of 70–85 nm. Blue shift of band gap with the Mg‐content is demonstrated, and photoluminescence (PL) from ZnO has been found to be tunable in a wide range from green to blue through Mg doping. The blue‐related PL therefore appeared to be caused by energetic shifts of the valence band and/or the conduction band of ZnO. Mg_xZn_1‐xO nanoparticles synthesized by polyacrylamide‐gel method after modified by polyethylene glycol surfactant have a remarkable improvement of stability in the ethanol solvent, indicating that these MZO nanoparticles could be considered as the candidate for the application of solution–processed technologies for optoelectronics at ambient temperature conditions.     

Synthesis,structural and optical properties of well dispersed anatase TiO2 nanoparticles by non‐hydrothermal method

The formation of nanocrystalline TiO₂ particles has been investigated via a surfactant‐free synthetic non‐hydrothermal method. Titanium isopropoxide and toluene were used as the starting materials. At a low temperature of 250 °C for 6 h, the reaction mixture turned in to a white precipitate (TiO₂) as a result of the thermal decomposition of metal alkoxide. The obtained product was found to crystallize purely in the anatase phase with well defined morphology. The powder XRD study confirms that the average size of the particle is close to ∼15 nm. The TEM analysis indicates the sizes of the primary and secondary particles in the range between 8‐10 nm and 15‐20 nm respectively. The quantum size confinement of the crystallites is evident from the blue shift of the absorption edge in the UV‐Visible absorption spectrum. The luminescence property of the TiO₂ nanoparticles studied by the emission spectrum confirms the presence of defect levels caused by the oxygen vacancies. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Low‐temperature preparation of bismuth ferrite microcrystals by a sol‐gel‐hydrothermal method

Well‐crystallized pure perovskite bismuth ferrite (BiFeO₃) powders with various morphologies have been synthesized by a novel sol‐gel‐hydrothermal route for the first time, which combined the conventional sol‐gel process and the hydrothermal method. The as‐prepared samples were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), differential thermal analysis (DTA) and ferroelectric test system. The results revealed that the compositions, morphological and dimensional changes in bismuth ferrite samples synthesized by sol–gel–hydrothermal method strongly depend on the concentrations of mineralizer. Ferroelectric hysteresis loops are displayed in the BiFeO₃ samples. The bismuth ferrites were hydrothermally synthesized at as low a temperature as 180 °C, which is comparatively lower than that synthesized by the normal sol–gel route. The formation mechanism of the bismuth ferrite crystalline was also discussed. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structure and photoluminescence properties of SrWO4 3D microspheres synthesized by the surfactant‐assisted hydrothermal method

In this paper, we report large‐scale high‐quality SrWO₄ 3D microspheres synthesized in aqueous solutions under mild conditions with cetyl trimethyl ammonium bromide as a simple cationic surfactant. These crystals have been characterized by X‐ray diffraction, transmission electron microscopy and field emission scanning electron microscopy techniques. The crystal growth processes were employed to investigate the formation mechanism of SrWO₄ 3D microspheres. Room‐temperature photoluminescence indicated that the as‐prepared SrWO₄ 3D microcrystals had strong emission peaks at about 432 and 505 nm, respectively.     

Optical and structural properties of lead iodide thin films prepared by vacuum evaporation method

Thermally processed lead iodide (PbI₂) thin films were prepared by the vacuum evaporation method in a constant ambient. Measured thickness of the film was verified analytically from the optical transmittance data in a wavelength range between 300 and 1600 nm. From the Tauc relation for the non‐direct inter band transition, the optical band gap of the film was found to be 2.58 eV for film thickness 300 nm. X‐ray diffraction analysis confirmed that PbI₂ films are polycrystalline, having hexagonal structure. The low fluctuation in Urbach energy indicates that the grain size is quite small. The present findings are in agreement with the other results. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Graphene oxide used as a surfactant to induce the flower‐like ZnO microstructures: growth mechanism and enhanced photocatalytic properties

In this paper, graphene oxide (GO) was used as a temple to induce the formation of flower‐like ZnO microparticals compared with surfactants, such as cetyltrimethylammonium bromide (CTAB) and dodecyl dimethyl betaine (BS‐12). The zinc hydroxide carbonate ((Zn₄(CO₃)(OH)₆,ZHC)) was produced by a hydrothermal reaction. The flower‐like ZnO microparticals were gained by calcining ZHC. In the GO medium, the microparticals were assembled by numerous porous nanosheets from one point (initial nucleus) to flower‐like microparticals finally. The nanosheets of graphene oxide and functional groups were likely to contribute to the formation of the precursor, and some nanosheets were retained in the complex. The growth mechanism of ZHC was also proposed in this paper. The photocatalytic activity of the flower‐like ZnO microparticals was evaluated by photo degradation reaction of rhodamine B (RhB). The peony‐like porous ZnO/rGO compounds showed high photocatalytic activity and better than ZnO microparticals formed in the CTAB and BS‐12. These results indicated that GO could be widely used as a surfactant to induce composite materials with special morphology and photoelectric properties, etc.     

Synthesis of radial‐like ZnO structure by hydrothermal method with ZnSO4·7H2O and Zn(CH3COO)2·2H2O as zinc sources

Radial‐like ZnO structures were prepared using zinc sulfate (ZnSO₄·7H₂O) and zinc acetate [Zn(CH₃COO)₂·2H₂O] as zinc sources by a facile template‐free hydrothermal method in this paper. Structural and optical properties of radial‐like ZnO structures are characterized by X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM), UV‐vis spectrophotometer and photoluminescence measurement (PL). It has been found that the distinct surface morphologies of radial‐like ZnO structures grown by different zinc sources. Slim radial‐like ZnO with a hexagonal wurtzite structure is grown by using ZnSO₄·7H₂O as zinc sources, whereas coarse radial‐like ZnO with zincite structure is achieved by zinc acetate. The UV‐vis absorption spectra of them both display an obvious and significant absorption in the ultraviolet region. The room temperature PL spectra of ZnO structures grown by two different zinc sources possess a common feature that consists of a strong ultraviolet (UV) peak and visible emission band.