LD泵浦Nd：YAG激光器的强度噪声特性研究

本文在理论研究了ＬＤ泵浦Ｎｄ：ＹＡＧ激光器的强度噪声特性，用传递函数的形式给出各种噪声湿源对激光器强度噪声的影响，计算结果指出，Ｎｄ：ＹＡＧ激光器输出的激光并非相干态光场，在几兆频率上存在高于散粒噪声基准几十ｄＢ的驰豫振荡噪声，在小于驰豫振荡频率范围，激光器的强度噪声基本上处于泵浦泵噪声水平。     

一种改进的激光二极管纵向泵浦固体激光器的腔模设计方法

以空间相关的速率方程理论为基础，提出了一种改进的激光二极管纵向泵浦固体激光器的设计方法，给出了在一定泵浦耦合方式下，激光腔模尺寸和输出耦合率最佳值的选取依据，以采用不同耦合系统的端面泵浦Ｎｄ：ＹＡＧ激光器设计实例，相应的实验结果与有理论计算符合得较好。     

Na2激光器双模运转行为研究

本文考虑了激光模式和泵浦光的空间分布,对线性驻波腔,我们建立了多模的麦克斯韦——布洛赫方程组,并由此导出了双模稳态条件下阈值泵浦功率和输出功率的表达式。讨论了双模Na₂激光器的运转行为,以及温度,Na₂蒸汽带长度及缓冲气体的压力对激光器的影响。得到了一些有用的结果。     

激光二极管面阵列泵浦固体激光器的理论分析

对于激光二极管侧面泵浦的固体激光器,泵浦光和振荡光场为空间分布函数,利用四能级速率方程,得到了激光器输入和输出参数之间的。分析了空间参数对激光器输出特性的影响,找到最佳参数。     

NAB和NYAB晶体的斯塔克能级

在液氮温度下测量ＮＡＢ和ＮＹＡＢ的全波段吸收光谱，并由此初步指认了ＮＡＢ和ＮＹＡＢ的斯塔克能级，利用Ｊ－Ｒ理论首次对ＮＡＢ和ＮＹＡＢ的斯塔克能级进行了全谱项拟合计算，并作了正确的指认。     

高功率双包层光纤激光器受激拉曼散射和热效应的理论研究

 受激拉曼散射和热效应会限制光纤激光器功率的提高。利用高功率光纤激光器的速率方程和热传导方程,理论研究了双端泵浦和分布泵浦下双包层光纤激光器的受激拉曼散射和热效应,得到了光纤中的泵浦光、激光和斯托克斯光的功率分布,光纤激光器的输出特性以及光纤中的温度分布。分析表明,当泵浦功率增大到一定值时,光纤激光器中出现SRS,一部分激光功率会转移给斯托克斯光,影响激光功率进一步提高;与双端泵浦方式相比,分布泵浦下光纤激光器的斜率效率和最大输出功率相差不大,但是,光纤中的温度分布被有效地降低,因此,分布泵浦方式更为有效。     

自锁模Cr∶LiSAF激光器的特性研究

本文分析上转换过程及荧光热猝灭效应对Ｃｒ∶ＬｉＳＡＦ激光器的泵浦阈值和输出功率的影响，由此得出Ｃｒ∶ＬｉＳＡＦ激光器特别适合低功率泵浦分析了三镜腔结构的特性，选择了腔的较佳参数，实现了在７５０ｍＷ的氩离子激光泵浦下三镜腔Ｃｒ∶ＬｉＳＡＦ激光器的自锁模运转     

二极管泵浦准三能级板条固体激光器的优化设计

基于最大激光增益条件，分析和优化了二极管泵浦准三能级Yb∶YAG固体板条激光器的激光增益、板条的最佳光学长度和最佳宽度参数。结果表明：在低功率侧面泵浦条件下，板条增益介质的掺杂浓度和板条宽度满足一定的关系，这为研究该类激光器提供了一条有效途径，其结果可应用于其他准三能级固体激光器设计。     

LD泵浦Nd:YAG微片激光器

ＬＤ泵浦Ｎｄ：ＹＡＧ微片激光器结构简单紧凑，与半导体激光器相比，前者具有激光线宽窄、光束质量好、相干长度长等优点，因此在一些测量领域有着较好的应用前景。目前对ＬＤ泵浦Ｎｄ：ＹＡＧ微片激光器的实验工作主要是获得单频、单模连续输出和线性频率调制特性研究。本文综述了近几年来ＬＤ泵浦Ｎｄ：ＹＡＧ微片激光器的研究方向、成果及应用，主要介绍了各国对ＬＤ泵浦Ｎｄ：ＹＡＧ微片激光器的调频特性的研究状况     

LD泵浦掺镱双包层光纤激光器的理论研究

对线形腔LD泵浦掺镱的双包层光纤激光器进行研究,通过数值模拟,分析了不同泵浦方式下的泵浦光、激光输出功率和增益特性在光纤中的分布。结果表明,单端后向泵浦输出功率率较高,对于小功率光纤激光器则是最佳选择。进一步又研究了单端后向对称泵浦输出功率与光纤长度及腔镜反射率的影响,为提高光纤激光器的输出功率提供了理论和实验依据。     

Performance of CW NYAB laser at 1.06 μm end-pumped by a high-power diode-laser-array

A CW NYAB laser at 1.06 μm end-pumped by a high-power diode-laser-array has been demonstrated. At the incident pump power of 11 W, a maximum output power of 3.2 W was achieved, resulting in an optical conversion efficiency of 29.1%, and average slope efficiency of 37.5%. The output beam quality factor was measured to be M²=1.9. The internal losses caused by the NYAB crystal were measured to be 0.035 cm⁻¹. The NYAB crystal was also found to exhibit very strong thermal lensing under high-power end-pumped conditions.     

Fiber Optic Coupling of CW Linear Laser Diode Array

Based on a set of microoptics the output radiation from a continuous wave (CW) linear laser diode array is coupled into a multi-mode optical fiber of 400 μm diameter.The CW linear laser diode array is a 1 cm laser diode bar with 19 stripes with 100 μm aperture spaced on 500 μm centers.The coupling system contains packaged laser diode bar,fast axis collimator,slow axis collimation array,beam transformation system and focusing system.The high brightness,high power density and single fiber output of a laser diode bar is achieved.The coupling efficiency is 65% and the power density is up to 1.03×104 W/cm2.     

Fiber Optic Coupling of CW Linear Laser Diode Array

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｌａｓｅｒｄｉｏｄｅａｒｒａｙ (ＬＤＡ )ｔｈａｔｈａｓｍｕｌｔｉｐｌｅｅｍｉｔｔｉｎｇｒｅｇｉｏｎｓｉｓａｐｅｒｆｅｃｔｄｅｖｉｃｅｔｏａｃｈｉｅｖｅｈｉｇｈｅｒｐｏｗｅｒｏｕｔｐｕｔｓｗｉｔｈａｎｉｎｃｒｅａｓｅｄｂｒｉｇｈｔｎｅｓｓ.ＴｈｅｈｉｇｈＣＷ ｐｏｗｅｒ ,ｈｉｇｈｂｒｉｇｈｔｎｅｓｓａｎｄｆｉｂｅｒｏｕｔｐｕｔｏｆａｌａｓｅｒｄｉｏｄｅｂａｒｃａｎｂｅａｐｐｌｉｅｄｉｎｍｅｄｉｃｉｎｅ ,ｍａｔｅｒｉａｌｓｐｒｏｃｅｓｓｉｎｇ ,ｓｏｌｉｄ ｓｔａｔｅｌａｓ…     

Thermal Lensing, Laser Performance at 1.06 μm and 0.53 μm of a NYAB Laser End-pumped by a Diode-laser-array

The thermal lensing, output characteristics of an end-pumped NYAB laser with high pump power levels and operated at the fundamental wavelength, and the manner of self-frequency-doubling, have been investigated. The thermal lensing in the NYAB crystal was found to be significantly stronger than that in Nd:YVO4 crystal. A maximum output of 3.2 W at 1.06 μm was achieved with an optical conversion efficiency of 29.1％ and an average slope efficiency of 37.5％. These results were found to be slightly inferior to those of Nd:YVO4 crystal. When operated in the fashion of selffrequency-doubling, 23 mW green output was obtained at the incident pump power of 5 W, such inefficient operation was attributed to the large mode size in the NYAB crystal.     

Thermal Lensing, Laser Performance at 1.06 μm and 0.53 μm of a NYAB Laser End pumped by a Diode laser array

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｓｅｌｆ ｆｒｅｑｕｅｎｃｙ ｄｏｕｂｌｉｎｇｌａｓｅｒｃｒｙｓｔａｌｓ,ｗｈｉｃｈｃｏｍｂｉｎｅｔｗｏｄｉｆｆｅｒｅｎｔｆｕｎｃｔｉｏｎｓｏｆｌａｓｅｒｅｍｉｓｓｉｏｎａｎｄｆｒｅｑｕｅｎｃｙｃｏｎｖｅｒｓｉｏｎ ,ｐｒｏｖｉｄｅａｓｉｍｐｌｅｗａｙｏｆｇｅｎｅｒａｔｉｎｇｃｏｈｅｒｅｎｔｖｉｓｉｂｌｅｒａｄｉａｔｉｏｎ .Ａｍｏｎｇｔｈｅｖａｒｉｏｕｓｓｅｌｆ ｆｒｅｑｕｅｎｃｙ ｄｏｕｂｌｉｎｇｃｒｙｓｔａｌｓ ,ｎｅｏｄｙｍｉｕｍｙｔｔｒｉｕｍａｌｕｍｉｎｕｍｂｏｒａ…     

Bismuth-doped silica-based fiber lasers operating between 1389 and 1538 nm with output power of up to 22 W

An efficient CW bismuth fiber laser operating around 1.46 μm with an efficiency of >50% and an output power of >20 W has been developed on a bismuth-doped GeO(2)-SiO(2) fiber. The laser demonstrates weak dependence of the output power on temperature in comparison with bismuth lasers operating near 1.15 and 1.3 μm. The laser generation has been obtained in the range 1.39 to 1.54 μm. The first linearly polarized bismuth-doped fiber laser at 1.46 μm based on a PANDA-type fiber has been demonstrated.     

A 1.5 W CW optically pumped 12.08 μm NH3 laser

Order-of-magnitude increase in output power and efficiency has been obtained from the new CW 12.08 μm NH₃ Raman laser optically pumped by low-pressure CO₂ laser. The 12.08 μm output power is analyzed as a function of the main operational parameters.     

Laser diode pumped LNYAB self-frequency-doubling lasers

The LNYAB self-doubling laser pumped by (LD) has been developed for the first time. The properties of the lasers are much better than those of NYAB self-doubling lasers pumped by LD. The LNYAB self-doubling laser pumped by LD can be operated in TEM_(00) mode with threshold pumping power of 3.6mW which is lower than that of LD pumped NYAB self-doubling lasers by 74%. The output power is 29mW at 0.531μm in green region with optical-to-optical efficiency of 4.8% which is higher than that of NYAB self-doubling laser by 20%.     

高亮度半导体激光阵列光纤耦合模块

利用2只915 nm半导体激光短列阵作为子模块,设计并研制出连续输出的高亮度光纤耦合模块。首先对每个半导体激光短列阵进行光束整形,从而提高它的光束质量;然后采用空间复用技术将这两个半导体激光短列阵出射的激光在光参数积小的方向上叠加,并利用偏振复用技术进一步提高光束质量;最后利用单片非球面透镜将激光聚焦到芯径为100 μm、数值孔径为0.22的光纤中。测量结果显示:在工作电流为52.5 A时,聚焦镜焦平面的光斑尺寸为105.4 μm;耦合后测量光纤出光功率可达72.6 W,对应亮度为6.08 MW/(cm²·sr),模块的电光转换效率为42.2%。最后测量了模块在不同驱动电流时的光谱,证明该模块的散热性能良好。     

200兆赫高功率CW锁模YAG激光泵浦源研究

本文报导一台200MHz 12W平均功率的CW锁模Nd:YAG激光泵浦源,输出脉宽约100ps,能够可靠地长期稳定运转。