Gelation and Swelling Behavior of Semi-Interpenetrating Polymer Network Hydrogels Based on Polyacrylamide and Poly(vinyl alcohol)

Novel semi-Interpenetrating Polymer Network (semi-IPN) hydrogels based on partially Hydrolyzed Polyacrylamide (HPAM) and Poly(Vinyl Alcohol) (PVA) were prepared by solution crosslinking using chromium triacetate. Effects of PVA content on the gelation process and swelling behavior in tap water and different electrolyte solutions were investigated. Study of the gelation behavior using dynamic rheometery showed that the limiting storage modulus of the semi-IPN gels decreased with increasing PVA content. It was also found that increasing the PVA content increases the loss factor, indicating that the viscous properties of this gelling system increase more strongly than the elastic properties. The swelling ratio of the semi-IPN gels in tap water decreased as the concentration of the PVA increased. However, the semi-IPN gels showed lower salt sensitivity factor in synthetic oil reservoir water as compared with HPAM gels. Therefore, they are potentially good candidates for enhanced oil recovery applications.     

Tuning of Lower Critical Solution Temperature (LCST) of Poly(N-Isopropylacrylamide-co-Acrylic acid) Hydrogels

Temperature-responsive hydrogel with a lower critical solution temperature (LCST) close to human body temperature was prepared. Crosslinked N-isopropylacrylamide (NIPAAm) and acrylic acid (AAc) copolymer networks were synthesized at various monomer ratios in the presence of ammonium persulfate (APS), N,N′-methylenebisacrylamide (NMBA) and N,N,N′,N′-tetramethylethylenediamine (TEMED) via a redox polymerization method. The resulting hydrogels possessed thermo- and pH-responsive characteristics. They were characterized in terms of swelling ratio, volume change, water uptake and diffusivity, water vapor uptake and diffusivity, and phase transition temperature. The water liquid and vapor diffusion coefficients for all the synthesized hydrogels were higher than the literature data, implying higher rates for drug release. The LCST of the hydrogel increased with higher AAc content in the copolymer. The gel containing 1.8% AAc exhibited an LCST similar to human body temperature, demonstrating a potential use in drug controlled release and biomedical applications.     

Optimization of Preparation Techniques for Poly(Lactic Acid-Co-Glycolic Acid) Nanoparticles

Microparticles and nanoparticles of poly(lactic acid-co-glycolic acid) (PLAGA) are excellent candidates for the controlled release of many pharmaceutical compounds because of their biodegradable nature. The preparation of submicron PLAGA particles poses serious challenges that are not necessarily present when preparing microparticles. We have evaluated several combinations of organic solvents and surfactants used in the formulation of PLAGA nanoparticles. Critical factors such as the ability to separate the nanoparticles from the surfactant, the ability to re-suspend the nanoparticles after freeze-drying, formulation yield and nanoparticle size were studied. The smallest particles were obtained using the surfactant/solvent combination of sodium dodecyl sulfate and ethyl acetate (65 nm) and the largest particles were obtained using poly(vinyl alcohol) and dichloromethane (466 nm). However, the optimal nanoparticles were produced using either acetone or ethyl acetate as the organic solvent and poly(vinyl alcohol) or human serum albumin as the surfactant. This is because the most critical measure of performance of these nanoparticles proved to be their ability to re-suspend after freeze-drying.     

Polyelectrolyte Complexes of Homo- and Copolymers of Vinyl Ether of Monoethanolamine with Poly(Acrylic Acid) in Aqueous Solutions

The complexation of homo- and copolymers of vinyl ether of monoethanolamine with poly(acrylic acid) has been studied in aqueous solutions. The effect of pH on the complexation has been shown. In acidic media (pH 2.4), the polyelectrolyte complex is enriched by anionic polymer units. In weakly acidic media (pH 4–6), the formation of stoichiometric polyelectrolyte complex is observed. In higher pH media (pH 6–8), the polycomplex contains an excessive amount of cationic polymer. The stability of the polyelectrolyte complexes is affected by the addition of inorganic salts and dimethylformamide.     

Investigation on the Heat Capacity of Water in Poly(Acrylic Acid)/Water Mixtures Through Stepscan Method

The heat capacity of poly(acrylic acid)/water mixtures with low water contents were measured by the stepscan differential scanning colorimetry (DSC) method and the C_p of the bound water in the mixtures were obtained based on simple equations with an assumption that the effect of interaction between polymer and water molecules could be ignored. The results indicated that the water decreased the glass transition temperature of poly(acrylic acid) (PAA), evidently as a plasticizer, and PAA/water mixtures were thermodynamically homogeneous blends. It was found that the C_p of nonfreezable water in PAA/water mixtures was higher than those of glassy water and cubic ice. The C_p increased with the water content, showing that average interactions between polymer and water decreased with water content. The C_p of bound water in the mixtures in the liquid state was lower than that of bulk water and also increased with water concentration, since the water molecules’ regular structures were broken. It showed that the C_p of bound water in the mixtures was lower than that of free water. The C_p of glassy water was calculated based on experimental C_p values of the PAA/water mixtures, which provided an easy way to obtain the C_p values of glassy water through a simple experiment. The values, however, were higher than those obtained by other researchers.     

Preparation and Property of Poly(N-isopropylacrylamide) (PNIPAAm)/Clay/Linear Polyacrylamide (PAAm) Nanocomposite Hydrogels

In this study, a linear polyacrylamide (PAAm) with an average viscosimetric molecular weight 3.97 × 10³ kg mol^?1 was added to the prereaction solution for the preparation of poly(N-isopropylacrylamide) (PNIPAAm)/clay nanocomposite hydrogels. The effects of the linear PAAm on the optical transparency and tensile property of the resulting PNIPAAm/clay/linear PAAm hydrogels were systematically investigated. The results revealed that the optical transparency and mechanical tensile properties of the resultant hydrogels strongly depended on the linear PAAm content. In particular, 5 wt% loading of linear PAAm led to almost fivefold decreases of transmittance at 25°C and a onefold increase of the tensile elongation at break. These characteristic changes were explained by a typical interpenetrating microstructure, which was formed by PNIPAAm due to the incorporation of linear PAAm in the PNIPAAm/clay network. The dynamic rheological test and infrared spectroscopy analysis on the mixed solutions consisting of linear PAAm and clay platelets further confirmed the interaction.     

Evaluation of the Complexation Process Between Poly(Aspartic Acid) and Poly(Ethylene Glycol) Through Dynamic Rheology and Electrokinetic Potential

Investigations concerning the interactions between the polymeric pair constituted of poly(aspartic acid) (PAS) as a proton-donating polycarboxilic acid and poly(ethylene glycol) (PEG) as a proton-accepting compound are continued from previous studies. The complexation between PAS and PEG has potential use as a matrix for encapsulation of bioactive substances with potential biomedical applications. The interactions that occurred were monitored in dilute solutions by determining the particle size distribution and the zeta potential (ZP) through laser light scattering method; data associated with oscillatory rheology was used as a complementary analysis. The influence of the ratio between the components and the temperature conditions during the complexation process brought additional data concerning the intermolecular links formed through hydrogen bonds.     

Improving the Barrier Properties of Poly(Lactic Acid) by Blending with Poly(Ethylene-Co-Vinyl Alcohol)

Poly(lactic acid) (PLA)/poly(ethylene-co-vinyl alcohol) (EVOH) blends were prepared via melt blending to improve the barrier properties of PLA. The phase morphologies and final properties (rheological behavior, thermal and dynamical-mechanical features, barrier properties, and mechanical behaviors) of the blends were investigated as a function of the EVOH content. The results indicated that hydroxyl groups of EVOH promoted the degradation of PLA, and thus affected the viscosities and morphologies of the resulting blends. The intrinsic viscosities of PLA in the blends decreased with the content of EVOH. The PLA and EVOH presented typical phase-separated morphologies, with a relatively small domain size of the EVOH phase. The EVOH enhanced the cold-crystallization behavior of PLA. The barrier properties to water vapor and oxygen increased linearly with increasing EVOH content.     

Thermoplastic Vulcanizate Based on Poly(lactic acid) and Acrylic Rubber Blended with Ethylene Ionomer

A new thermoplastic vulcanizate (TPV) was developed by meltblending of poly(lactic acid) (PLA), acrylic rubber (ACM), and ethylene-methacrylic acid with sodium ions (EMAA-Na). The PLA/ACM/EMAA-Na blend showed low-yield strength, low modulus, and excellent strain recovery. It also demonstrated an increase in complex viscosity and decrease in melting temperature due to the interfacial reaction between the PLA and the ACM phases. The Fourier transform infrared spectroscopy results indicate that EMAA-Na can interact with both PLA and ACM, and that the Na⁺ ions act as a catalyst for the interfacial reaction between PLA and ACM, while PLA does not react with ACM without EMAA-Na. Moreover, the tensile strength at break of the PLA/ACM/EMAA-Na blend was observed to be extremely improved by the addition of hexamethylenediaminecarbamate (HMDC) due to the increasing of the cross-link density inside the rubber phase. The morphology of the PLA/ACM/EMAA-Na blend with HMDC was finer than that of PLA/ACM/EMAA-Na without HMDC. From the results, it is suggested that the interfacial reaction between the PLA and the ACM phases, the cross-linking in the ACM phase, and the finer morphology improved the mechanical properties of the blend.     

Isothermal Crystallization and Melting Behavior of Composites Composed of Poly(L-lactic Acid) and Poly(glycolic Acid) Fibers

Several composites of poly (L-lactic acid) (PLLA) with poly (glycolic acid) (PGA) fibers were prepared. The isothermal crystallization kinetics and melting behavior of PLLA and all of the composites were characterized by using differential scanning calorimetry. The experimental data were processed by using the Avrami equation. The relative parameters, such as the Avrami exponent and half-time crystallization, revealed that PGA fibers had positive effects on the crystallization of PLLA, but these effects had only a minimal dependence on the PGA fiber content. Moreover, at low isothermal crystallization temperatures (85°C～110°C), recrystallization during the heating scan was observed, which could lower the melting point of the samples to a certain extent.     

Surface Modification of Poly(tetrafluoroethylene) Microporous Membranes by Acrylic Acid Liquid-Phase Graft Copolymerization

Air plasma-pretreated poly(tetrafluoroethylene) (PTFE) films were subjected to further surface modification by liquid-phase graft copolymerization with acrylic acid monomer (AAc). The surface compositions and microstructures of the modified films were characterized by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). An exterior graft copolymerization of AAc on the PTFE fiber was indicated by the SEM photographs. The XPS results indicated that the F/C atomic ratio of the membranes were 1.837 and 1.207, and the O/C atomic ratio were 0 and 0.112 for the original and liquid-phase grafted PTFE membranes, respectively. The pore size distributions of the treated and untreated PTFE membranes, measured by the bubble-point method, were much smaller than that of the untreated membrane.     

Poly(allylamine) Stabilized Iron Oxide Magnetic Nanoparticles

This paper describes a new method for the dispersing and surface-functionalization of metal oxide magnetic nanoparticles (10 nm) with poly(allylamine) (PAA). In this approach, Fe₃O₄ nanoparticles, prepared with diethanolamine (DEA) as the surface capping agent in diethyleneglycol (DEG) and methanol, are ligand exchanged with PAA. This method allows the dispersing of magnetic nanoparticles into individual or small clusters of 2–5 nanoparticles in aqueous solutions. The resulting nanoparticles are water soluble and stable for months. The PAA stabilized Fe₃O₄ nanoparticles are characterized by TEM, TGA, and FT-IR. The PAA-coated Fe₃O₄ nanoparticles will allow further chemical tailoring and engineering of their surfaces for biomedical applications.     

Synthesis and Kinetic Study of Thermal Cycloimidization of Novel Poly(Amide Amic Acid) to Poly(Amide Imide) by Thermogravimetric Analysis

A new series of fluorinated poly(amide imide)s (PAIs) were prepared by polycondensation of diamine amic acid (DAA) with isophthaloyl, terephthaloyl, or trimellitic anhydride chloride in dimethylformamide, and their subsequent thermal cycloimidization. DAAs were obtained by reacting 4, 4′ (hexafluoroisopropylidene) diphthalic anhydride (6FDA) with diamines in dimethylformamide at 0–5°C. The kinetics of thermal cycloimidization of poly(amide amic acid) (PAA) to PAIs was investigated by thermogravimetric analysis under isothermal conditions at four different temperatures, i.e. 175, 200, 225, and 260°C, for 75 min. A generalized equation to calculate the theoretical amount of weight loss upon complete imidization, i.e. T_w % = 18Nw/R _Mw, was developed. In the above equation numeral 18 corresponds to the molecular weight of water, N is the number of water molecules, which are eliminated per repeat unit of PAA upon cycloimidization, w is the weight of PAA taken for TGA, and R _Mw is the molecular weight of the repeat unit of PAA. The polymers were characterized by FT-IR spectra. Complete cycloimidization process is discussed in terms of monomer structure (diamines and acid chlorides), effect of imidization temperature and time, types of linkages (meta or para) present, and influence of electron withdrawing groups, such as sulfone, in the monomer structure. It was observed that cycloimidization occurred at a faster rate at the beginning, up to about 30 min, and then proceeded at a slower rate till the end of curing. The thermal and thermooxidative stabilities of PAIs were also investigated in nitrogen and oxygen atmosphere.     

Microstructure,Rheology, and Potential Oil Absorbency of Poly(Butyl Methacrylate) and Poly(Hydroxyethyl Methacrylate) Blends

To prepare oil-absorptive polymers with moderate cross-linking structure, poly(butyl methacrylate) (PBMA) was synthesized as a linear hydrophobic polymer by suspension polymerization. In addition, hydroxyethyl methacrylate (HEMA), as a monomer, which could construct a network structure among the macromolecules via hydrogen bond interactions, was solution polymerized in dimethylacetamide (DMAc) with PBMA, yielding a polymer blend of PBMA and PHEMA. The solution of the polymer blend was investigated by rotational viscometry and extended rheometry. The results showed that the viscosity varied greatly with the temperature and shear rate for three different compositions. Fourier transform infrared (FTIR) spectra indicated that an entanglement or interlocking cross-linking structure of molecular chains was constructed by hydrogen bonds. The results from nuclear magnetic resonance (NMR) spectra exhibited a downfield movement of the proton peak as influenced by end groups or hydroxyls in the polymer chains. The rheological measurements demonstrated that the cross-linking structure greatly affected the rheological behavior of the blend solution. In addition, the cross-linking structure was also evaluated by oil absorbency of films.     

Synthesis and Characterization of Biodegradable Poly(lactic-co-glycolic acid)

A series of poly(lactic-co-glycolic acid) (PLGA) was synthesized by bulk ring-opening copolymerization with different ratios of L-lactic acid (L-LA) to glycolic acid (GA); stannous octoate [Sn(Oct)2] was used as catalyst. The structures were characterized by FT-IR. The crystallinity and the glass-transition temperature (T_g) were studied by differential scanning calorimeter (DSC). T_g decreased with the increase of GA and the rate of degradation and degree of hydrophilicity increased with the increased content of GA.     

高压对溶液中聚左旋乳酸单晶生长的影响

采用高压技术实现了500 MPa下聚左旋乳酸(PLLA)在稀薄二甲苯溶液中的单晶生长,采用透射电子显微镜、拉曼光谱和红外光谱对样品的结晶形态和结构进行了表征,考察了高压对聚左旋乳酸单晶生长行为的影响。结果表明,在相同的结晶温度和时间下,高压结晶PLLA的单晶仍为α-型晶体,但单晶尺寸明显大于常压样品;高压环境下PLLA分子链在晶核两端的生长扩散速率不同,容易形成非对称的菱晶形态;高压影响PLLA晶体中分子链的构象分布;在单晶生长期,高压诱导有利于PLLA晶体成核,但不利于单晶生长。     

Crystallization Behavior of Poly(Lactic Acid) Filled with Modified Carbon Black

A novel method was employed to modify the surface of carbon black (CB) by an organic small molecule in a Haake Rheomix mixer. The modified carbon black (MCB) was dispersed uniformly in poly(lactic acid; PLA). The crystallization behaviors of PLA, PLA/CB and PLA/MCB composites were investigated by differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD), small-angle X-ray scattering (SAXS) and polarizing optical microscopy. It is found that the addition of CB or MCB can influence the crystallization behavior of PLA. PLA/MCB has a faster crystallization rate and higher crystallization peak temperature than PLA/CB. For non-isothermal studies, Jeziorny and Mo equations were employed. The Mo equation can well describe the non-isothermal crystallization of the three samples. For PLA/CB and PLA/MCB composites containing 3wt% fillers, the nucleating activity for CB is about 0.32, and about 0.16 for MCB. All these results show that MCB is an effective nucleating agent. PLA/MCB has a higher nucleation rate than PLA/CB because of the finer dispersed particles size and improved interaction between MCB and PLA.     

Preparation and Characterization of Poly(Vinyl Alcohol) (PVA)/SiO2, PVA/Sulfosuccinic Acid (SSA) and PVA/SiO2/SSA Membranes: A Comparative Study

Abstract

New organic–inorganic nanocomposites based on PVA, SiO₂ and SSA were prepared in a single step using a solution casting method, with the aim to improve the thermomechanical properties and ionic conductivity of PVA membranes. The structure, morphology, and properties of these membranes were characterized by Raman spectroscopy, small- and wide-angle X-ray scattering (SAXS/WAXS), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), water uptake (Wu) measurements and ionic conductivity measurements. The SAXS/WAXS analysis showed that the silica deposited in the form of small nanoparticles (～ 10?nm) in the PVA composites and it also revealed an appreciable crystallinity of pristine PVA membrane and PVA/SiO₂ membranes (decreasing with increasing silica loading), and an amorphous structure of PVA/SSA and PVA/SSA/SiO₂ membranes with high SSA loadings. The thermal and mechanical stability of the nanocomposite membranes increased with the increasing silica loading, and silica also decreased the water uptake of membranes. As expected, the ionic conductivity increased with increasing content of the SSA crosslinker, which is a donor of the hydrophilic sulfonic groups. Some of the PVA/SSA/SiO₂ membranes had a good balance between stability in aqueous environment (water uptake), thermomechanical stability and ionic conductivity and could be potential candidates for proton exchange membranes (PEM) in fuel cells.     

On Localization of Clay Nanoparticles in Polypropylene/poly(Lactic Acid) Blend Nanocomposites: Correlation with Mechanical Properties

Two polypropylene (PP)/polylactide (PLA)/clay ternary nanocomposite systems, i.e. PP-rich and PLA-rich ones, each containing various amounts of one of two types of clay, were prepared by one step melt compounding in a twin screw extruder. The microstructures of the developed systems were correlated with tensile and impact properties. A theoretical calculation using wetting coefficients was used for predicting the clay nanoparticles localization in the blends. The nanoparticles were almost completely located within the PLA phase in both the PP-rich and PLA-rich systems, in good agreement with the predictions. Addition of a compatibilizer led to localization of the nanoparticles at the interfaces of the blends. From the wide angle X-ray scattering (WAXS) spectra it was concluded that the incorporation of clay led to intercalated structures in the both systems. The increase in impact toughness of the compatibilized blend nanocomposites, with respect to the uncompatibilized ones, was attributed to the weakened interfacial debonding in the presence of the interfacial-localized nanoparticles.     

Fabrication of Poly(D,L-lactide-co-glycolide) Microspheres and Degradation Characteristics in vitro

Poly(D,L-lactide-co-glycolide) (PLGA, 75/25) microspheres were prepared by the emulsion solvent extraction/evaporation technique and their degradation behaviors in vitro at 37°C were investigated. PLGA microspheres with a smooth and nonporous surface were obtained, with a mean particle size of 114.15 μm. It was observed that mass loss and water uptake of PLGA increased with increasing degradation time; however, weight average molecular weight and the pH value of the phosphate buffered saline (PBS) solution decreased. The observed relative rates of mass loss vs. molecular weight decreases were consistent with the explanation that PLGA underwent bulk degradation rather than surface degradation. During the degradation time, the surface of the PLGA microspheres became coarse and there were many micropores that developed upon immersion in the PBS. The microspheres lost their spherical form with increasing degradation time.