The nature of in-plane skeleton Raman modes of P3HT and their correlation to the degree of molecular order in P3HT:PCBM blend thin films

The nature of main in-plane skeleton Raman modes (C=C and C-C stretch) of poly(3-hexylthiophene) (P3HT) in pristine and its blend thin films with [6,6]-phenyl-C(61)-butyric acid methyl ester (PCBM) is studied by resonant and nonresonant Raman spectroscopy and Raman simulations. Under resonant conditions, the ordered phase of P3HT with respect to its disordered phase is identified by (a) a large shift in the C=C mode peak position to lower wavenumber (~21 cm(-1) shift), (b) a narrower fwhm of the C=C mode (~9 cm(-1) narrower), (c) a larger intensity of the C-C mode relative to the C=C mode (~56% larger), and (d) a very small Raman dispersion (~5 cm(-1)) of the C=C mode. The behavior of the C=C and C-C modes of the ordered and disordered phases of P3HT can be explained in terms of different molecular conformations. The C=C mode of P3HT in P3HT:PCBM blend films can be reproduced by simple superposition of the two peaks observed in different phases of P3HT (ordered and disordered). We quantify the molecular order of P3HT after blending with PCBM and the subsequent thermal annealing to be 42 ± 5% and 94 ± 5% in terms of the fraction of ordered P3HT phase, respectively. The increased molecular order of P3HT in blends upon annealing correlates well with enhanced device performance (J(SC), -4.79 to -8.72 mA/cm(2) and PCE, 1.07% to 3.39%). We demonstrate that Raman spectroscopy (particularly under resonant conditions) is a simple and powerful technique to study molecular order of conjugated polymers and their blend films.     

Thermal stability of P3HT and P3HT:PCBM blends in the molten state

The thermal stability of poly(3-hexylthiophene) (P3HT) in its molten state was investigated in air and nitrogen atmospheres under no illumination conditions, with the aim of testing the feasibility of processing it using polymer melt techniques. A large set of different experimental characterization techniques was used including thermogravimetric analysis (TGA), rotational rheometry, infrared spectroscopy (FTIR-ATR), proton nuclear magnetic resonance spectroscopy (¹H-NMR), gel permeation chromatography (GPC), UV-Vis and fluorescence spectroscopy. The results obtained strongly suggest that the processing of P3HT in its molten state is possible, without noticeable degradation, if carried out under nitrogen atmosphere and if the processing (residence) times are relatively short. Conversely, as expected, in a normal air atmosphere P3HT degrades rapidly at temperatures above its melting point. The effect of PCBM on the thermal stability of P3HT:PCBM blends in the molten state was also studied using TGA, and in air atmosphere PCBM is shown to delay oxidation.     

利用相容剂调控聚噻吩/富勒烯共混薄膜形貌

选择含有噻吩环的富勒烯衍生物([6,6]-噻吩基-C61-丁酸甲酯(TCBM-Cn,n代表在噻吩环5位的烷基链碳原子数))作为聚3-己基噻吩(P3HT)和[6,6]-苯基-C61-丁酸甲酯(PCBM)共混体系的相容剂,讨论了结晶能力不同的TCBM-Cn分子对共混体系相容性和P3HT结晶行为的影响.当使用强结晶性的相容剂TCBM-C0时,虽然不能完全抑制PCBM的聚集,但由于分子中噻吩环结构的存在,少量的相容剂即可提高P3HT的结晶度.而对于弱结晶性的相容剂TCBM-C6,虽然可以完全抑制PCBM的聚集,但是只有当其含量超过PCBM时,最终才能达到促进P3HT结晶的目的.     

Isothermal crystallization of P3HT:PCBM blends studied by RHC

Defining appropriate annealing temperatures and times is vitally important for increasing the efficiency of bulk heterojunction solar cells by favoring the crystallinity of the polymer-fullerene blend components. In order to better understand the annealing process, the isothermal crystallization of poly(3-hexyl thiophene) (P3HT) and [6,6]-phenyl C₆₁-butyric acid methyl ester (PCBM) blend investigated by means of rapid heating cooling calorimetry (RHC). Isothermal crystallization experiments at temperatures in between the glass transition and melting, within the temperature range of 70–150 °C, can successfully be performed since RHC permits cooling at a sufficiently high rate in order to prevent crystallization during cooling. Crystallization isotherms were determined from the subsequent melting behavior of the blend. They were measured for a wide set of annealing temperatures and times, and the evolution of the crystallization rate with temperature is compared for annealing from the glassy state and from the melt state.     

Photovoltaic Performance and Charge Recombination Dynamics of P3HT/PCBM Blend Heterojunction

We prepared the polymer solar cell based on poly（3-hexylthiophene）（P3HT）/fullerene derivative PCBM（PCBM=[6,6]-phenyl-C61-butyric acid methyl ester） heterojunction and investigated the irradiation intensi- ty-dependent charge recombination dynamics of heterojunction employing nanosecond transient absorption spectroscopy with bias light so as to simulate the photophysical process in heterojunction when the photovoltaic device is on operation. The experimental data exhibit that the yield of free charges gradually decreases and the loss of mobile carriers originated from bimolecular recombination simultaneously increases as the irradiation intensity gradually enhances. This indicates that the polymer solar cell is much suitably used at a low irradiation intensity.     

P3HT stripe structure with oriented nanofibrils enabled by controlled inclining evaporation

The preparation of the poly(3-hexylthiophene) (P3HT) stripe structure with oriented nanofibrils prepared by controlled inclining evaporative technique is reported. The distance of the adjacent stripes could be controlled from 40 μm to 100 μm by decreasing the inclining angle. The oriented nanofibrils in the stripes can be obtained because the P3HT lamellae diffuse directionally and form 1D crystals at the three-phase contact line of the drop. In order to get the oriented P3HT stripes, the proper solvent evaporation rate which is controlled by the inclining angle and the wettability of the substrate must be carefully chosen to match the P3HT 1D crystallization rate. It is found that large inclining angle and the hydrophilic substrate (for example: glass and PEDOT) are beneficial to get P3HT stripe structure with oriented nanofibrils.     

退火处理提高P3HT:PCBM聚合物太阳能电池光伏性能

利用旋转涂膜方法制备了以P3HT:PCBM为有源层的聚合物太阳能电池, 器件结构为ITO/PEDOT:PSS/P3HT:PCBM/Al(氧化铟锡导电玻璃/聚二氧乙基噻吩:聚对苯乙烯磺酸/聚三已基噻酚:富勒烯衍生物/铝),研究了退火温度对聚合物太阳能电池性能的影响. 实验发现: 聚合物薄膜经过120 °C退火10 min处理后, 开路电压(V_oc)达到0.64 V, 短路电流密度(J_sc)为10.25 mA·cm^-2, 填充因子(FF) 38.1%, 光电转换效率(PCE)达到2.00%. 为了讨论其内在机制, 对不同退火条件下聚合物薄膜进行了各种表征. 从紫外-可见吸收光谱中发现, 退火处理使P3HT在可见光范围内吸收加强且吸收峰展宽, 特别是在560和610 nm处的吸收强度明显增大; X射线衍射(XRD)结果表明, 120 °C退火后P3HT在(100)晶面上的衍射强度是未退火薄膜的2.8倍, 有利于光生载流子的输运; 原子力显微镜(AFM)研究结果表明, 退火显著增大了P3HT与PCBM的相分离程度, 提高了激子解离的几率; 傅里叶变换红外(FTIR)光谱验证了退火并没有引起聚合物材料物性的变化.     

退火处理提高P3HT:PCBM聚合物太阳能电池光伏性能

利用旋转涂膜方法制备了以P3HT:PCBM为有源层的聚合物太阳能电池, 器件结构为ITO/PEDOT:PSS/P3HT:PCBM/Al(氧化铟锡导电玻璃/聚二氧乙基噻吩:聚对苯乙烯磺酸/聚三已基噻酚:富勒烯衍生物/铝),研究了退火温度对聚合物太阳能电池性能的影响. 实验发现: 聚合物薄膜经过120 °C退火10 min处理后, 开路电压(V_oc)达到0.64 V, 短路电流密度(J_sc)为10.25 mA·cm^-2, 填充因子(FF) 38.1%, 光电转换效率(PCE)达到2.00%. 为了讨论其内在机制, 对不同退火条件下聚合物薄膜进行了各种表征. 从紫外-可见吸收光谱中发现, 退火处理使P3HT在可见光范围内吸收加强且吸收峰展宽, 特别是在560和610 nm处的吸收强度明显增大; X射线衍射(XRD)结果表明, 120 °C退火后P3HT在(100)晶面上的衍射强度是未退火薄膜的2.8倍, 有利于光生载流子的输运; 原子力显微镜(AFM)研究结果表明, 退火显著增大了P3HT与PCBM的相分离程度, 提高了激子解离的几率; 傅里叶变换红外(FTIR)光谱验证了退火并没有引起聚合物材料物性的变化.     

Structural variability and dynamics of the P3HT/PCBM interface and its effects on the electronic structure and the charge-transfer rates in solar cells

Using a range of realistic interface geometries obtained from a molecular dynamics simulation we study the effects of different microscopic atomic arrangements on the electronic structure and charge transfer rates of the prototypical photovoltaic interface between P3HT (poly(3-hexylthiophene)) and PCBM ([6,6]-phenyl-C(61)-butyric acid methyl ester). The electronic structures of charge-transfer (CT) states belong to two groups that can be denoted as "charge-separated" and "charge-bridging" states. For the former group of structures, which may lead to fully separated charges, the ranges and the average values of internal reorganization energy, the electronic coupling and the charge separated states energy are evaluated. A range and distribution of absolute charge separation (CS) and recombination (CR) rates are computed using the Marcus-Levich-Jortner rate equation. Due to the variety of P3HT/PCBM interface structures, a very broad range of CS (7.7 × 10(9)-1.8 × 10(12) s(-1)) and CR (2.5 × 10(5)-1.1 × 10(10) s(-1)) "instantaneous" rates are computed. However, the energetic parameters affecting the rate evolve in time due to the dynamic nature of the interface with a characteristic timescale of about 10 ns. For this reason the slowest CR instantaneous rates are not observed and the minimum CR rate observed is determined by the rate of conformational rearrangement at the interface. The combination of these observations provides a more general framework for the interpretation of experimental spectroscopic data, suggesting that the analysis based on simple first order rates may be insufficient to describe charge transfer in organic solar cell interfaces.     

3-甲基吡啶在有机物/水混合溶剂中的电氧化

在质子交换膜为隔膜的电解槽内,以丙酮、乙腈和2-丁酮与水分别构成混合溶剂体系,通过循环伏安和恒电位电解实验,探索了3-甲基吡啶在混合溶剂中在PbO2电极上的电氧化条件,并与纯水溶剂的情况相比,研究了氧化电流密度及生成烟酸的选择性和电流效率的变化.     

Improvement of Power Conversion Efficiency of P3HT/PCBM Polymer Solar Cell Systems by Optimization of the Process Steps

In this work, different steps involved in the fabrication of polymer solar cells were optimized using P3HT/PCBM heterojunction. Steps included spinning speed for coating of the PEDOT:PSS layer, use of filter for the PEDOT:PSS layer, spinning speed for coating of the active layer, sequence of annealing of the active layer either before or after electrode deposition, and modification of the cooling mechanism (either by cooling rapidly or slowly after heating of the active layer). Investigation of these steps led to an improvement of the power-conversion efficiency (PCE) of the polymer solar cells, especially the last step involving the change of cooling mechanism, which improved PCE by 25%.     

Improved photovoltaic performance of P3HT:PCBM cells by addition of a low band-gap oligomer

The introduction of a low band-gap oligomer, oligo(benzo[1,2,5]thiadiazole-alt-3,3'-dihexylquaterthiophene) (BT4T) improved the performance of P3HT:PCBM bulk heterojunction organic photovoltaic cells due to improved UV-vis absorption and increased P3HT crystallinity.     

Solvent‐Dependent Structure Formation in Drying P3HT:PCBM Films Studied by Molecular Dynamics Simulations

Phase separation in the donor‐acceptor blend poly(3‐hexylthiophene‐2,5‐diyl):[6,6]‐phenyl‐C61‐butyric acid methyl ester (P3HT:PCBM) during evaporation of a solvent using coarse‐grained molecular dynamics simulations is studied here. To this end, an equilibrated P3HT:PCBM:solvent mixture is placed in an elongated simulation box, after which solvent molecules are removed at regular time intervals from a region above the film. Three often‐used solvents are considered: chloroform (CFM), chlorobenzene (CLB), and orthodichlorobenzene (oDCB). The coarse‐grained solvent–solvent interaction parameters are tuned to reproduce the atmospheric boiling temperatures, while the PCBM–solvent interaction parameters are tuned to reproduce the PCBM solubilities. Other parameters are taken from the literature. During evaporation, the formation of a crust that is depleted of solvent, in which aggregation of P3HT and PCBM occurs, is observed. In agreement with experiment, the top region of the dry film is rich in PCBM for the cases of CLB and oDCB, and rich in P3HT for the case of CFM, while the very top layer of the film is always rich in P3HT. This vertical separation is ascribed to a competition between the tendency of P3HT to move to the surface due to its low surface energy and the different tendencies of PCBM to be dragged along to the surface by the evaporating solvent depending on its solubility. Also in agreement with experiment, the P3HT–PCBM interface area is larger for CLB and oDCB than for CFM. For CLB and oDCB, an indication for a spinodal P3HT–PCBM decomposition starting from the top and bottom surface is found, whereas for CFM the phase separation appears to be initiated in the bulk of the film.

     

Correlating the scattered intensities of P3HT and PCBM to the current densities of polymer solar cells

Grazing-incidence X-ray diffraction and rocking scans have quantified the structure of poly(3-hexylthiophene) and [6,6]-phenyl-C(61)-butyric acid methyl ester in the active layers of organic solar cells. Our study reveals that the device J(SC) correlates with the local structural development of pure PCBM and, to second order, the extent of out-of-plane P3HT π-stacking.     

Effect of polydispersity on the bulk‐heterojunction morphology of P3HT:PCBM solar cells

Bulk heterojunctions (BHJs) based on semiconducting electron–donor polymer and electron–acceptor fullerene have been extensively investigated as potential photoactive layers for organic solar cells (OSCs). In the experimental studies, poly‐(3‐hexyl‐thiophene) (P3HT) polymers are hardly monodisperse as the synthesis of highly monodisperse polymer mixture is a near impossible task to achieve. However, the majority of the computational efforts on P3HT: phenyl‐C61‐butyric acid methyl ester (P3HT:PCBM)‐based OSCs, a monodisperse P3HT is usually considered. Here, results from coarse‐grained molecular dynamics simulations of solvent evaporation and thermal annealing process of the BHJ are shared describing the effect of variability in molecular weight (also known as polydispersity) on the morphology of the active layer. Results affirm that polydispersity is beneficial for charge separation as the interfacial area is observed to increase with higher dispersity. Calculations of percolation and orientation tensors, on the other hand, reveal that a certain polydispersity index ranging between 1.05 and 1.10 should be maintained for optimal charge transport. Most importantly, these results point out that the consideration of polydispersity should be considered in computational studies of polymer‐based OSCs. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 895–903     

Nanocomposites composed of P3HT:PCBM and nanoparticles synthesized by laser ablation of a bulk PbS target in liquid

Nanoparticles synthesized by laser ablation of bulk target materials in liquids have ligand-free surfaces since no chemical precursors are used for their synthesis, and thus, they are ideally suited for applications in the fabrication of organic solar cells in which the properties of the interface between the nanoparticles and the polymer blend matrix largerly determine the exciton splitting and transport of carriers to the external electrodes, properties crucial for the device operation and performance. Narrow band gap semiconducting quantum dots can act as sensitizers, increasing the absorption of the device active layer in the infrared part of the solar spectrum. In this work, a bulk PbS target was laser ablated (450 fs, 1,064 nm, 1 kHz) in ethanol for the synthesis of nanoparticle colloidal solutions. The solutions exhibit a broad absorption which extends at the longest wavelength measured of ~1,700 nm and beyond. The nanoparticles were directly mixed with the blend P3HT:PCBM for the formation of nanocomposites. The nanocomposites with the nanoparticles exhibit lower transmission in the whole spectral range as compared to the blend without the nanoparticles.     

Surface tension calculation of mixed solvents with respect to solvent composition and temperature by using Jouyban-Acree model

Applicability of a solution model, i.e. Jouyban-Acree model (JAM), for calculating surface tension of binary and ternary solvents at various temperatures has been shown employing experimental surface tension data collected from the literature. The accuracy of the model was evaluated by calculating average percentage deviation (APD) between calculated and observed values. The obtained overall APD (+/-S.D.) for JAM using binary solvent data were 4.06 (+/-4.27) and 8.07 (+/-9.78)%, respectively for correlative and predictive analyses. The corresponding values for the best similar model from the literature were 8.86 (+/-6.40) and 37.10 (+/-27.65)% and the mean APD differences between JAM and previously published model were significant (p<0.003). The capability of JAM for correlating surface tension of ternary solvents at various temperatures was also shown and the overall APD was 1.39 (+/-0.37)%.     

基底温度对刮涂制备的P3HT:PCBM薄膜形貌和光伏电池性能的影响

研究了刮涂制备P3HT:PCBM(P3HT:聚3-己基噻吩,PCBM:[6,6]-苯基-C61-丁酸甲酯)活性层的过程中,基底温度对P3HT:PCBM活性层薄膜性质和电池性能的影响.结果表明,提高基底温度在缩短薄膜干燥时间的同时,抑制了PCBM相的大尺度聚集,并改善了P3HT:PCBM薄膜中P3HT在(100)方向上的结晶程度,但降低了π-π共轭方向上的有序度.制备的光伏电池经过进一步退火处理后可形成良好的互穿网络结构,能量转换效率可达3.93％.     

Formation of the surface charge on silica in mixed solvents

At sufficiently high concentrations of methanol and of alkali salts in aqueous silica dispersions, the negative -potentials of the particles are decreased. This effect is more pronounced with lithium than with other alkali cations, and it is independent on the anion. The NMR spectra indicate lithium adsorption on silica from mixed solvents, but not in the absence of alcohol.Supported by a contract with the XMX Corporation, Burlington, Massachusetts, USA