The impact of cellulose structure on binding interactions with hemicellulose and pectin

Four cellulose substrates including highly crystalline cellulose nanowhiskers (CNWs) from Gluconacetobacter xylinus (cellulose Iα) or cotton (cellulose Iβ) and amorphous cellulose derived from CNWs (phosphoric acid swollen cellulose nanowhiskers, PASCNWs) were used to explore the interaction between cellulose and well-defined xyloglucan, xylan, arabinogalactan and pectin. The binding behavior was characterized by adsorption isotherm and Langmuir models. The maximum adsorption and the binding constant of xyloglucan, xylan and pectin to any CNWs were always higher than to PASCNWs derived from the same source. The binding affinity of xyloglucan, xylan and pectin to G. xylinus cellulose was generally higher than to cotton cellulose, showing that binding interactions depended on the biological origin of cellulose and associated differences in its structure. The surface area, porosity, crystal plane and degree of order of cellulose substrate may all impact the interactions.     

Biosynthesis, production and applications of bacterial cellulose

Bacterial cellulose (BC) as a never-dried biopolymer synthesized in abundance by Gluconacetobacter xylinus is in a pure form which requires no intensive processing to remove unwanted impurities and contaminants such as lignin, pectin and hemicellulose. In contrast to plant cellulose, BC, with several remarkable physical properties, can be grown to any desired shape and structure to meet the needs of different applications. BC has been commercialized as diet foods, filtration membranes, paper additives, and wound dressings. This review article presents an overview of BC structure, biosynthesis, applications, state-of-the-art advances in enhancing BC production, and its material properties through the investigations of genetic regulations, fermentation parameters, and bioreactor design. In addition, future prospects on its applications through chemical modification as a new biologically active derivative will be discussed.     

Preparation and mechanical properties of bacterial cellulose nanocomposites loaded with silica nanoparticles

Bacterial cellulose (BC), which is produced by Gluconacetobacter xylinus (Ga. xylinus) in culture, is made up of a three-dimensional network of ribbon-shaped bundles of cellulose microfibrils. In the current studies, we used two processes to prepare nanocomposites of BC filled with silica particles. In Process I, Ga. xylinus was incubated in medium containing silica sol Snowtex 0 (ST 0, pH 2–4) or Snowtex 20 (ST 20, pH 9.5–10.0). The elastic modulus at 20 °C was improved by keeping the amount of silica in the nanocomposites below 4% when ST 20 was used and below 8.7% when ST 0 was used. This process allowed incorporation of 50% silica in BC. Inclusion of higher amounts of silica reduced the modulus at 20 °C and the strength of the nanocomposites below that of BC. X-ray diffraction measurements revealed that the silica particles disturb the formation of ribbon-shaped fibrils and affect the preferential orientation of the ( ) plane. We also produced BC-silica nanocomposites by Process II, wherein the BC hydrogel was immersed in different concentrations of silica sols, allowing silica particles to diffuse into the BC hydrogel and lodge in the spaces between the ribbon-shaped fibrils. This method increased the modulus at 20°C and the strength compared to the BC matrix, but it was difficult to load the BC with more than 10% silica in this way.     

Characterization of water-soluble exopolysaccharides from Gluconacetobacter xylinus and their impacts on bacterial cellulose crystallization and ribbon assembly

Gluconacetobacter xylinus has the ability to produce different types of water soluble exopolysaccharides (EPS). Those EPS have different levels of association to bacterial cellulose (BC). At least a portion of the EPS can be released from the BC by 0.1 to 4 M NaOH solution treatments. Hard to extract EPS (HE-EPS) released by 4 M NaOH solutions have been characterized and contain approximately 75 % mannose and 25 % glucose. To study the effect of the EPS on BC synthesis, purified EPS were added to the medium at the start of cultivation and the BC produced was characterized. Results showed that the presence of HE-EPS in the culture medium interfered with the alignment of the BC crystals, but did not reduce crystal size. This is in contrast to similar studies performed using xyloglucan, xylan and glucomannan. The width of the average ribbon increased by 60 % when HE-EPS levels increased in the medium, which indicated that the HE-EPS could also modulate the bundling of cellulose ribbons. Based on the data we propose a mechanism for how HE-EPS alters cellulose formation and assembly. The addition of HE-EPS disturbs the preferential crystal orientation and increases the spacing of cellulose microfibrils without affecting crystallization by associating with ordered cellulose prior to physical aggregation or bundling.     

Characterizing wood polymers in the primary cell wall of Norway spruce (<Emphasis Type="Italic">Picea abies</Emphasis> (L.) Karst.) using dynamic FT-IR spectroscopy

Dynamic Fourier Transform Infra-Red (FT-IR) spectroscopy was used to examine the interactions among cellulose, xyloglucan, pectin, protein and lignin in the outer fibre wall layers of spruce wood tracheids. Knowledge regarding these interactions is fundamental for understanding the fibre separation in a mechanical pulping process. Sheets made from an enriched primary cell wall material were used for studying the viscoelastic response of the polymers. The results indicated that strong interactions exist among lignin, protein, pectin, xyloglucan and cellulose in the primary cell wall. This signified a closely linked network structure of the components on the fibre surface. This ultrastructural arrangement in the primary cell wall and the relatively high content of lignin, pectin and protein in it, means that the primary cell wall is more submissive to selective chemical attacks, when compared to the secondary cell wall. A low ratio of cellulose Iα to cellulose Iβ in the primary cell wall was also found.     

Synthesis of regenerated bacterial cellulose-zinc oxide nanocomposite films for biomedical applications

Regenerated bacterial cellulose (RBC) composites with zinc-oxide nanoparticles (ZnO) were prepared using a new strategy for enhanced biomedical applications of BC. Powdered BC was dissolved in N-methylmorpholine-N-oxide, and different concentrations of ZnO nanoparticles were mixed into the BC solution. RBC, RBC-ZnO1 (1 % ZnO) and ZnO-RBC2 (2 % ZnO) nanocomposite films were prepared by casting the solutions through an applicator. FE-SEM images confirmed the structural features and impregnation of the RBC films by nanoparticles. XRD analysis indicated the presence of specific peaks for RBC and ZnO in the composites. The RBC nanocomposites were found to have greatly enhanced thermal, mechanical and biological properties. Specifically, the degradation temperatures were improved from 334 °C for RBC to 339 and 344 °C for RBC-ZnO1 and RBC-ZnO2, respectively. The mechanical strength and Young’s modulus of the composites were also higher than those of pure RBC. The greatly improved antibacterial properties of the RBC-ZnO nanocomposites are the most striking feature of the present study. The bacterial growth inhibition measured for the RBC was zero, but reached up to 34 and 41 mm for RBC-ZnO1 and RBC-ZnO2, respectively. In addition to their antibacterial properties, the RBC-ZnO nanocomposites were found to be nontoxic and biocompatible with impressive cell adhesion capabilities. These RBC-ZnO nanocomposites can be used for different biomedical applications and have the potential for use in bioelectroanalysis.     

Parenchyma cell wall structure in twining stem of <Emphasis Type="Italic">Dioscorea balcanica</Emphasis>

Anatomical adaptation of liana plants includes structural changes in cell walls of different tissues: fibers, vessel elements and tracheids. However, the contribution of parenchyma cells to stem twining in liana plants is mostly unknown. The aim of this investigation is to determine changes in stem parenchyma cell walls that are correlated with the twinning process in liana plants. Parenchyma cell wall structure was studied on the stem cross sections of straight and twisted internodes of monocotyledonous liana Dioscorea balcanica, by different microscopy techniques: light microscopy, scanning electron microscopy, fluorescence detected linear dichroism microscopy and Fourier transform infrared microspectrometry. In addition, chemical analysis of the entire stem internodes was performed using photometric and chromatographic methods. Parenchyma cell walls of twisted D. balcanica internodes are characterized by: lower amounts of cellulose (obtained by FTIR microspectrometry) with different cellulose microfibril orientation (shown by Scanning electron microscopy), but no changes in “cellulose fibril order” (obtained by Differential polarization laser scanning microscopy); lower amounts of xyloglucan, higher amounts of xylan, higher amounts of lignin with modified organization—less condensed lignin (obtained by FTIR microspectrometry). At the same time, chemical analysis of the entire internodes did not show significant differences in lignin content and cell wall bound phenols related to stem twining, except for the presence of diferulate cross-links exclusively in twisted internodes. Our results indicate that adaptations to mechanical strain in D. balcanica stems involve modifications in parenchyma cell wall structure and chemistry, which provide decreased stiffness, higher strength and increased elasticity of twisted internodes.     

Influence of chemical surface modification of cellulose nanowhiskers on thermal,mechanical, and barrier properties of poly(lactide) based bionanocomposites

In the aim of producing fully organic bionanocomposite based on poly(lactide) (PLA), cellulose nanowhiskers (CNW) were grafted by n-octadecyl-isocyanate (CNW-ICN) applying an in situ surface grafting method. The compatibilizing effect of the long aliphatic grafted chain was investigated by thermal, mechanical and permeability analysis of solvent cast nanocomposite films. The grafted CNW-ICN could be successfully dispersed in the polymer matrix. The gained compatibility brought about a nucleating effect, decreasing the half time of isothermal crystallization from 25 min for the neat PLA to 8.4 min for the nanocomposite including 2.5 wt% CNW-ICN, e.g., tensile strength was improved by 10 MPa for the same 2.5 wt% CNW-ICN/PLA composite. Mechanical reinforcement was also effective in the rubbery state of PLA and increased the tensile modulus of the rubbery plateau providing thereby thermal resistance to the polymer. Oxygen barrier properties did not change significantly upon the inclusion of CNW-ICN, even when the quantity of CNW-ICN was increased to 15 wt%. More interestingly, the water vapour permeability of the CNW-ICN nanocomposite was always lower than the one of ungrafted CNW composites, which led to the conclusion that the hydrophobic surface graft and improved compatibility could counteract the effect of inclusion of hydrophilic structures in the matrix on water vapour transport. In conclusion, the surface grafting of CNW with isocyanates might be an easy and versatile tool for designing fully organic bionanocomposites with tailored properties.     

Bacterial cellulose films: influence of bacterial strain and drying route on film properties

Structural properties of bacterial cellulose (BC) depend on the microstructure of the material, which in turn is influenced by the bacterial strain. This paper reports the production of BC thin films from two bacterial strains, gluconacetobacter xylinus (GX) and gluconacetobacter europaeus (GE), and three methods of drying the films; at room temperature, freeze drying and supercritical drying. The porosity, transparency, water absorption capacity (WAC) and mechanical properties of the obtained films are further investigated. We conclude that materials with different properties can be fabricated by selecting the bacterial strain or the drying method. Supercritical drying of films of GE achieved mechanically robust and extremely light films, 0.05 g/mL, with up to 96 % of porosity, and with a WAC up 110 times their dried weight. We determined that materials resulting from GE strain are not much affected by the drying method. On the other hand, GX produced BC films more sensitive to the drying method used. Films are denser, 0.6–0.2 g/mL, with tunable porosity from 60 to 90 % and their maximum WAC is 66 times their dried weight.     

On the use of plant cellulose nanowhiskers to enhance the barrier properties of polylactic acid

Polylactic acid (PLA) nanocomposites were prepared using cellulose nanowhiskers (CNW) as a reinforcing element in order to asses the value of this filler to reduce the gas and vapour permeability of the biopolyester matrix. The nanocomposites were prepared by incorporating 1, 2, 3 and 5 wt% of the CNW into the PLA matrix by a chloroform solution casting method. The morphology, thermal and mechanical behaviour and permeability of the films were investigated. The CNW prepared by acid hydrolysis of highly purified alpha cellulose microfibers, resulted in nanofibers of 60–160 nm in length and of 10–20 nm in thickness. The results indicated that the nanofiller was well dispersed in the PLA matrix, did not impair the thermal stability of this but induced the formation of some crystallinity, most likely transcrystallinity. CNW prepared by freeze drying exhibited in the nanocomposites better morphology and properties than their solvent exchanged counterparts. Interestingly, the water permeability of nanocomposites of PLA decreased with the addition of CNW prepared by freeze drying by up to 82% and the oxygen permeability by up to 90%. Optimum barrier enhancement was found for composites containing loadings of CNW below 3 wt%. Typical modelling of barrier and mechanical properties failed to describe the behaviour of the composites and appropriate discussion regarding this aspect was also carried out. From the results, CNW exhibit novel significant potential in coatings, membranes and food agrobased packaging applications.     

Revision of adsorption models of xyloglucan on microcrystalline cellulose

Interactions among cellulose, hemicellulose and pectins are important for plant cell wall assembly and properties and also for industrial applications of these polysaccharides. Therefore, binding of pectin and xyloglucan on microcrystalline cellulose was investigated in this experiment by adsorption isotherms, zeta potential and scanning electron microscopy (SEM). Analysis of three isotherm models (Langmuir, Freundlich and Fowler-Guggenheim isotherms) showed that the experimental adsorption isotherm was well described via the Fowler-Guggenheim model, which includes lateral interaction between the adsorbate. The adsorption isotherm and zeta potential measurement showed that at temperature 25 °C only xyloglucan adsorbed on the microcrystalline cellulose. In case of xyloglucan on cellulose, the equilibrium was reached in about 3–4 h, and the kinetics of adsorption were well described by the multiexponential equation. Analysis of the model suggests that two steps can be distinguished: diffusion and reconformation in an adsorbed layer. No adsorption of pectin was observed in this study. SEM study showed that xyloglucan may prevent cellulose from aggregation.     

Cellulose microfibril orientation in onion (Allium cepa L.) epidermis studied by atomic force microscopy (AFM) and vibrational sum frequency generation (SFG) spectroscopy

Cellulose microfibril orientation in plant cell walls changes during cell expansion and development. The cellulose microfibril orientation in the abaxial epidermis of onion scales was studied by atomic force microscopy (AFM) and sum frequency generation (SFG) vibrational spectroscopy. Onion epidermal cells in all scales are elongated along the onion bulb axis. AFM images showed that cellulose microfibrils exposed at the innermost surface of the abaxial epidermis are oriented perpendicular to the bulb axis in the outer scales and more dispersed in the inner scales of onion bulb. SFG analyses can determine the orientation of cellulose microfibrils averaged over the entire thickness of the cell wall. We found that the average orientation of cellulose microfibrils inside onion abaxial epidermal cell walls as revealed by SFG is similar to the orientation observed at the innermost cell wall surface by AFM. The capability to determine the average orientation of cellulose microfibrils in intact cell walls will be useful to study how cellulose microfibril orientation is related to biomechanical properties and the growth mechanism of plant cell walls.     

Models of Xyloglucan Binding to Cellulose Microfibrils1

Abstract

Molecular modeling is used to investigate the ways in which plant cell wall xyloglucans might bind to the surface of cellulose microfibrils. Binding involving the xyloglucan backbone is found to be sterically restricted. Plausible models are obtained that involve hydrogen bonding between the xylose residues and one kind of cellulose surface. In such a model, the xyloglucan sidechains mediate, as well as modulate, the binding.     

Sustainable optically transparent composites based on epoxidized soy-bean oil (ESO) matrix and high contents of bacterial cellulose (BC)

Production of transparent composites from totally renewable resources with extraordinary potential for different applications can be made possible using cellulose. Composites of epoxidized soybean oil (ESO)/bacterial cellulose (BC) nanofibers have been prepared with high fiber content. Due to the nano-order scale network-like structure of BC nanofibers, composite films present high transparency even at high BC content. Transparency of films has been analyzed by UV–visible spectroscopy observing that only 15% of matrix transmittance is lost in the nanocomposites. ESO/BC composites show better mechanical properties with increasing BC content. Composites combine high stiffness and good ductility due to the incorporation of BC network structure in ESO matrix.     

Homogeneous and porous modified bacterial cellulose achieved by in situ modification with low amounts of carboxymethyl cellulose

To improve the rehydration ability of bacterial cellulose (BC), many macromolecules have been used as modifiers in previous reports. However, the aggregation of additives in the BC matrix appears to be inevitable. We investigated different parts of a BC pellicle, which was achieved by in situ modification with carboxymethyl cellulose (CMC) in culture with Gluconacetobacter xylinus ATCC53582 or Enterobacter sp. FY-07. We observed a concentration gradient of CMC in the BC pellicle from G. xylinus ATCC53582, but not with Enterobacter sp. FY-07. Low concentrations of CMC (0.01 %, m/v) are sufficient to modify BC in situ in culture with Enterobacter sp. FY-07, in which CMC could sufficiently contact with the newly formed BC. The crystallinity of the modified BC decreased by more than 39.8 %, and its rehydration ability and water holding capacity increased by 43.3 and 31.0 %, respectively. Unlike the pellicle of modified BC achieved from obligate aerobes, such as G. xylinus ATCC53582, that produced by Enterobacter sp. FY-07 exhibited better homogeneity and porosity.     

Glutaraldehyde treatment of bacterial cellulose/fibrin composites: impact on morphology, tensile and viscoelastic properties

Bacterial cellulose/fibrin composites were treated with glutaraldehyde in order to crosslink the polymers and allow better match of the mechanical properties with those of native small-diameter blood vessels. Tensile and viscoelastic properties of the glutaraldehyde treated composites were determined from tensile static tests and cyclic creep tests, respectively. Glutaraldehyde-treated (bacterial cellulose) BC/fibrin composites exhibited tensile strength and modulus comparable to a reference small-diameter blood vessel; namely a bovine coronary artery. However, the breaking strain of the glutaraldehyde-treated composites was still well below that of the native blood vessel. Yet a long strain hardening plateau was induced by glutaraldehyde treatment which resembled the stress–strain response of the native blood vessel. Tensile cyclic creep test indicated that the time-dependent viscoelastic behavior of glutaraldehyde-treated BC/fibrin composites was comparable to that of the native blood vessel. Covalent bonding between BC and fibrin occurred via glutaraldehyde, affording mechanical properties comparable to that of the native small blood vessel.     

Development of Nanocomposites from Bacterial Cellulose and Poly(vinyl Alcohol) using Casting-drying Method

Nanocomposites of bacterial cellulose (BC) and poly(vinyl alcohol) (PVA) were prepared by cast-drying method as an easy way in producing nanocomposite films and to expand the use of BC. The contribution of PVA in nanocomposites was evaluated by measurement of cross-sectional surface, moisture uptake and mechanical properties. Morphological analysis shows that PVA covered a number of cellulosic fibres and formed denser material as a function of PVA addition. Based on the tensile test, the addition of PVA causes a very slight reduction compared with bacterial cellulose itself. The BC/PVA nanocomposites still have similar stiffness to BC with elongation at break less than 5%, while PVA film shows ductile properties with elongation at break more than 80%. On the other hand, the presence of BC fibres in the PVA matrix enhanced the tensile strength and the elastic modulus of pure PVA about two to three times, but it decreased the toughness of pure PVA. The highest tensile strength and elastic modulus of the nanocomposites are 164 MPa and 7.4 GPa, respectively at BC concentration of 64%. Increasing BC concentration is proportional to reducing moisture uptake of BC/PVA nanocomposites indicating that the existence of BC fibres inhibits moisture absorption.     

Visualization of the nanoscale pattern of recently-deposited cellulose microfibrils and matrix materials in never-dried primary walls of the onion epidermis

For more than 10 years epidermal cell layers from onion scales have been used as a model system to study the relationship between cellulose orientation, cell growth and tissue mechanics. To bring such analyses to the nanoscale, we have developed a procedure for preparing epidermal peels of onion scales for atomic force microscopy to visualize the inner surface (closest to the plasma membrane) of the outer epidermal wall, with minimal disturbance and under conditions very close to the native state of the cell wall. The oriented, multilayer distribution of cellulose microfibrils, approximately ~3 nm wide, is readily observed over extended lengths, along with other features such as the distribution of matrix substances between and on top of microfibrils. The microfibril orientation and alignment appear more dispersed in younger scales compared with older scales, consistent with reported values for mechanical and growth anisotropy of whole epidermal sheets. These results open the door to future work to relate cell wall structure at the nm scale with larger-scale tissue properties such as growth and mechanical behaviors and the action of cell wall loosening agents to induce creep of primary cell walls.     

Comparative physical and chemical analyses of cotton fibers from two near isogenic upland lines differing in fiber wall thickness

The thickness of cotton fiber cell walls is an important property that partially determines the economic value of cotton. To better understand the physical and chemical manifestations of the genetic variations that regulate the degree of fiber wall thickness, we used a comprehensive set of methods to compare fiber properties of the immature fiber (im) mutant, called immature because it produces thin-walled fibers, and its isogenic wild type Texas Marker-1 (TM-1) that is a standard upland cotton variety producing normal fibers with thick walls. Comprehensive structural analyses showed that im and TM-1 fibers shared a common developmental process of cell wall thickening, contrary to the previous report that the phase in the im fiber development might be retarded. No significant differences were found in cellulose content, crystallinity index, crystal size, matrix polymer composition, or in ribbon width between the isogenic fibers. In contrast, significant differences were detected in their linear density, cross-section micrographs of fibers from opened bolls, and in the lateral order between their cellulose microfibrils (CMFs). The cellulose mass in a given fiber length was lower and the CMFs were less organized in the im fibers compared with the TM-1 fibers. The presented results imply that the disruption of CMF organization or assembly in the cell walls may be associated with the immature phenotype of the im fibers.     

The effect of fiber content on the mechanical and thermal expansion properties of biocomposites based on microfibrillated cellulose

A new method to obtain composites of phenolic resin reinforced with microfibrillated cellulose with a wide fiber content was established and the mechanical properties were evaluated by tensile test. A linear increase in Young’s modulus was observed at fiber contents up to 40 wt%, with a stabilizing tendency for higher fiber percentages. These results were ratified by measurements of the coefficient of thermal expansion (CTE) relative to fiber content, which indicated a strong thermal expansion restriction rate below 60 wt% fiber content, indicating the effective reinforcement attained by the cellulose microfibrils. The low CTE achieved of 10 ppm/K is one of the important properties of cellulose composites.