Silica–titania aerogel monoliths with large pore volume and surface area by ambient pressure drying

Ambient pressure drying has been carried out for the synthesis of silica–titania aerogel monoliths. The prepared aerogels show densities in the range 0.34–0.38 g/cm³. The surface area and pore volume of these mixed oxide aerogels are comparable to those of the supercritically dried ones. The surface area for 5wt% titania aerogel has been found to be as high as 685 m²/g with a pore volume of 2.34 cm³/g and the 10wt% titania aerogel has a surface area of 620 m²/g with a pore volume of 2.36 cm³/g. Some gels were also made hydrophobic by a surface treatment with methyltrimethoxysilane and trimethylchlorosilane. The surface modified aerogels possess high surface areas in the range of 540–640 m²/g, and are thermally stable in terms of retaining hydrophobicity up to a temperature of 520 °C. The pore size distribution of the aerogels clearly indicates the preservation of the aerogel structure. High Resolution Transmission Electron microscopy has been employed to characterise the aerogels and Fourier Transform infrared spectroscopy to study the effect of titania addition to silica and the surface modification. X-ray diffraction patterns were recorded to verify the molecular homogeneity of the aerogel.     

Synthesis of the Zn1.9Cu0.1SiO4 pigment via the sol–gel and coprecipitation methods

Journal of Sol-Gel Science and Technology - The Zn1.9Cu0.1SiO4 pigment was obtained by two variants of “soft” chemistry methods: using sol–gel synthesis in ethanol from TEOS and...     

Synthesis of titanium dioxide nano-powder via sol–gel method at ambient temperature

Titanium dioxide is a semiconductor with excellent photo catalytic properties and an important material with high regarded in nanotechnology. In this study, titanium dioxide nanoparticles was successfully synthesized via sol–gel method using tetra-n-butyl orthotitanate, hydrochloric acid and ammonia. Tetra-n-butyl orthotitanate was used as precursor. The ingredients were mixed at ambient temperature for 9 h on a magnetic stirring, sol was formed and converted to gel by adding ammonia. X-ray diffraction analysis clearly showed anatase and rutile phases so that, with increasing calcination temperature anatase converts to the rutile. Scanning electron microscopy was used for agglomerate observations. Energy-dispersive detector analysis was carried out and confirmed the formation of titanium dioxide. The influences of calcination temperature and pH value on particles size were studied. The results indicate that synthesis at room temperature reduced the particle size to 15 nm.     

Optically transparent silica aerogels based on sodium silicate by a two step sol–gel process and ambient pressure drying

Interest in improving the optical transmission of sodium silicate-based aerogels by ambient pressure drying led to the synthesis of aerogels using a two-step sol–gel process. To produce optically transparent silica aerogel granules, NH₄F (1 M) and HCl (4 M) were used as hydrolyzing and condensation catalysts, respectively. The silica aerogels were characterized by their bulk density, porosity (%), contact angle and thermal conductivity. Optical transmission of as synthesized aerogels was studied by comparing the photos of aerogel granules. Scanning electron microscopic study showed the presence of fractal structures in these aerogels. The degree of transparency in two step sol–gel process-based aerogels is higher than the conventional single step aerogels. The N₂ adsorption–desorption analysis depicts that the two step sol–gel based aerogels have large surface areas. Optically transparent silica aerogels with a low density of ∼0.125 g/cc, low thermal conductivity of ∼0.128 W/mK and higher Brunauer, Emmett, and Teller surface area of ∼425 m²/g were obtained by using NH₄F (1 M), HCl (4 M), and a molar ratio of Na₂SiO₃::H₂O::trimethylchlorosilane of 1::146.67::9.46. The aerogels retained their hydrophobicity up to 500 °C.     

Thermal stability of Al-modified silica aerogels through epoxide-assisted sol–gel route followed by ambient pressure drying

Bone infections in human beings are an essentially destructive problem with crucial clinical and economic effects; thus, incorporation of antibiotics such as amoxicillin (AMX) into the scaffold was developed as an effective treatment for bone infections. In this respect, we develop new nanostructured bredigite (Bre; Ca₇MgSi₄O₁₆)–amoxicillin (AMX; α-amino-hydroxybenzyl-penicillin) scaffolds containing different concentrations of amoxicillin (0, 3, 5, and 10%) by using space holder method to assure bactericidal properties. The result depicted that the Bre–AMX scaffolds possess porosity of 80–82% with high compressive strength of 1.2–1.4?MPa and controlled antibiotic release for prevention of infection. Bre–(3–10%)AMX scaffolds were able to destroy Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) bacteria, as well as effectively inhibit the growth of bacterial cells; in addition, the antibacterial activity of the AMX-loaded scaffolds augmented with the increase of the AMX concentration. Sustained drug release was detected from Bre–AMX scaffolds accompanied by initial burst release of 20% for 8?h, followed by a sustained release, which is favorable for bone infection treatment. These new Bre–(3–5%)AMX scaffolds possess excellent mechanical properties and antibacterial activity with no cytotoxicity suggested as an appropriate alternative for bone infection treatment.

Open image in new window

     

Thickness effects in naturally superhydrophilic TiO2–SiO2 nanocomposite films deposited via a multilayer sol–gel route

TiO₂–SiO₂ nanocomposite films of various thicknesses have been deposited via a multilayer sol–gel route. These films exhibit a natural and persistent superhydrophilicity, which allows considering new applications for easy to clean surfaces. Atomic force microscopy, scanning and transmission electron microscopy, as well as ellipsometry and UV/visible spectrometry measurements, were performed to study how the multilayer procedure influenced the morphology and composition of composite films in relation to their thickness. The natural and photo-induced wettability of these films was studied and discussed in relation to morphology, composition, and thickness features. It is concluded that, while such features did not significantly influence the natural wettability of nanocomposite films, their photo-induced wettability was considerably enhanced when increasing their thickness, which favored a faster superhydrophilicity photo-regeneration when this natural property started to disappear after a long aging period in ambient atmosphere.     

Efficient removal of oil pollutant via simultaneous adsorption and photocatalysis using La–N–TiO2–cellulose/SiO2 difunctional aerogel composite

Research on Chemical Intermediates - Nano-TiO2 photocatalysts doped with La–N(La–N–TiO2) were prepared by solgel method. The La–N–TiO2 was loaded on the cellulose/SiO2...     

Synthesis of silica nanoparticles by modified sol–gel process: the effect of mixing modes of the reactants and drying techniques

A modified preparation of silica nanoparticles via sol–gel process was described. The ability to control the particle size and distribution was found highly dependent on mixing modes of the reactants and drying techniques. The mixture of tetraethoxysilane and ethanol followed by addition of water (Mode-A) produced monodispersed powder with an average particle size of 10.6 ± 1.40 nm with a narrow size distribution. The freeze drying technique (FD) further improved the quality of powder. In addition, the freeze dried samples have shown unique TGA decomposition steps which might be related to the well-defined structure of silica nanoparticles as compared to the heat dried samples. DSC analysis showed that FD preserved the silica surface with low shrinkage and generated remarkably well-order, narrow and bigger pore size and pore volume and also large endothermic enthalpies (ΔH _FD = −688 J g⁻¹ vs. ΔH _HD = −617 J g⁻¹) that lead to easy escape of physically adsorbed water from the pore at lower temperature.     

Synthesis of high-temperature resistant monolithic zirconia-based aerogel via facile water glass assisted sol–gel method

Zirconia aerogel monolith was prepared by a facile co-hydrolysis method, which adopts ZrOCl₂ as the precursor and water glass (Na₂SiO₃) as the gel initiator. ZrO₂ aerogel was formed by rational controlling of the hydrolysis rate of Zr⁴⁺ ions by Na₂SiO₃. The obtained aerogel consists of ZrO₂ nanoparticles surrounded by amorphous SiO₂ nano shell. The density and the surface area can be well tuned by adjusting the ratio of ZrOCl₂ to Na₂SiO₃. The in-situ introduced SiO₂ nano shell layer acts as the particle boundary reinforcement phase, which not only strengths the ZrO₂ particle connections to form monolith, but also significantly mitigates the sintering of ZrO₂ nanoparticles at high temperature. As a result, the zirconia aerogel prepared by such method could maintain its nanoporous microstructure up to 1000?°C.

Open image in new window

     

Fire retardancy effects in single and double layered sol–gel derived TiO2 and SiO2-wood composites

Sol–gel derived TiO₂ and SiO₂-wood inorganic composites are prepared by direct vacuum infiltration of silicon and titanium alkoxide based precursors in pine sapwood in one or two cycles followed by a controlled thermal curing process. The resulting flame retardancy effect is investigated under two different fire scenarios using cone calorimetry and oxygen index (LOI). Heat release rates (HRR) especially the values for the second peak, are reduced moderately for all single layered composites. This effect is more pronounced for double layered composites where HRR was reduced up to 40 % showing flame retardancy potential in developing fires. Beside this, smoke release was lowered up to 72 % indicating that these systems had less fire hazards compared to untreated wood, whereas no meaningful improvement is realized in terms of fire load (total heat evolved) and initial HRR increase. However impressively, the LOI of the composites were increased up to 41 vol% in comparison to 23 vol% for untreated wood displaying a remarkable flame retardancy against reaction to a small flame. An approximate linear interdependence among the fire properties and the material loading as well as fire residue was observed. A residual protection layer mechanism is proposed improving the residue properties for the investigated composites.     

Preparation and characterization of crack-free sol–gel based SiO2–TiO2 hybrid nanoparticle film

Owing to the diverse potential applications of hybrid silica–titania thin films, the synthesis and characterization of these films have been carried out with a special focus on application as a medium index layer for multilayered functional coatings. For synthesis, tetraethylorthosilicate and titanium tetraisopropoxide were chosen as precursors for the formation of silica-titania hybrid thin films/nano-composites through an in situ sol–gel process. These films were sequentially obtained on Cu substrate utilizing spin coating. The hybrids were characterized by field emission scanning electron microscope, energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction, atomic force microscopy and Fourier transform infrared spectroscopy (FTIR). Field emission scanning electron microscope morphology displayed a smooth, densified and crack- free layer of silica-titania hybrid nanoparticles in the range of 20–71 nm after calcinations at low temperature of 300ºC for 1 h. X-ray diffraction pattern confirms the phases of titania with higher crystallinity and phase transformation at low temperature. The prepared films were uniform with low 8.852 nm RMS value. The stoichiometry of films was confirmed by EDX results. The FTIR spectroscopy indicated the establishment of heterogeneous chemical bonding between the Ti and Si surfaces through oxygen.     

Synthesis and characterization of SiO2–CrO3, SiO2–MoO3, and SiO2–WO3 mixed oxides produced using the non-hydrolytic sol–gel process

Silica-based mixed oxide xerogels, namely SiO₂–CrO₃, SiO₂–MoO₃, and SiO₂–WO₃, were prepared using the non-hydrolytic sol–gel process. The materials were synthesized using metal chloride:tetraethoxysilane (TEOS) molar ratios of 0.1:2; 0.2:2 and 0.4:2 for each metal chloride and 1:2 SiCl₄:TEOS molar ratio. All of the xerogels containing Cr, Mo or W had considerably greater surface areas than that of SiO₂. The small angle X-ray scattering experiments suggest that the surface roughness of the aggregates in SiO₂–CrO₃ is less than that of SiO₂–MoO₃ and SiO₂–WO₃. The morphological characteristics of the silica-based mixed oxide xerogels were not affected by the nature and amount of metal chloride employed in the synthesis. An irregular morphology was observed for SiO₂–CrO₃, SiO₂–MoO₃ and SiO₂–WO₃, but a lamellar structure was observed for SiO₂. X-ray photoelectron spectroscopy analysis suggests that tungsten species were preferentially distributed on the outmost part of the grain. The resulting particle diameter was shown to be lower for the mixed oxides compared to that of bare silica. Furthermore, the presence of metals (Cr, Mo and W) on silica caused a decrease in the size of the particles as the atomic radii of these metals increased. According to the Fourier transform infrared spectroscopy and Raman, Cr, Mo and W were incorporated within the silica framework.     

TiO2 and TiO2/SiO2 nanoparticles obtained by sol–gel method and applied on dye sensitized solar cells

In this work we show the synthesis and characterization of TiO₂ and TiO₂/SiO₂ nanoparticles synthesized by sol–gel method using HF and HCl as catalysts. The obtained nanoparticles were analyzed by N₂ adsorption–desorption isotherms, transmission electronic microscopy, Ultraviolet–visible spectroscopy and X-ray diffractometry. Mesoporous, homogeneously polycondensed TiO₂/SiO₂ materials, containing nanocrystalline anatase phase with band gap similar to pure titania were obtained. Films of the powdered oxides were applied to assemble dye sensitized solar cells that presented electrical parameters, Fill Factor and efficiencies similar to devices obtained by only TiO₂. The sol–gel route arises as an alternative way to prepare TiO₂/SiO₂ materials for solar cells.     

Effect of microstructure and surface roughness on the wettability of superhydrophobic sol–gel nanocomposite coatings

Sol–gel nanocomposite coatings were fabricated by spraying precursor mixtures containing hydrophobically modified silica (HMS) nanoparticles dispersed in sol–gel matrices prepared with acid-catalyzed tetraethoxysilane (TEOS), and methyltriethoxysilane (MTEOS). The hydrophobicity of the coatings increased with increase in the concentration of HMS nanoparticles. Superhydrophobic coatings with water contact angle (WCA) of 166° and roll-off angle <2° were obtained by optimizing the sol–gel processing parameters and the concentration of silica nanoparticles in the coating. FESEM studies have shown that surface has a micro-nano binary structure composed of microscale bumps and craters with protrusions of nanospheres. The properties of composite coatings fabricated by spin coating and spray coating methods were compared. It was found that the microstructure and the wettability were also dependent on the method of application of the coating.     

Synthesis and characterization of nitrogen-doped TiO2 nanoparticles prepared by sol–gel method

The N-doped TiO₂ has been synthesized by sol?Cgel method, using titanium isopropoxide, isopropanol and an aqueous solution of ammonia with ratio 2:1:10. The concentrations used for the NH₃ aqueous solution were 3, 7, 10 and 15?%. The samples have been analysed by X-ray diffraction, electron microscopy (SEM and TEM) thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), micro-Raman spectroscopy and diffuse reflectivity. TEM, SEM, DSC and TGA showed that the morphology is influenced by the presence of N^3? ions but not by the concentration of the solution. Instead reflectance gave us a relation between values of the energy gap and the concentration of N^3? ions: the gap between valence and conduction band lowers as the concentration of NH₃ in the starting solution increases. From these results we can say that the properties of the material have been tuned by doping with nitrogen ions because the particles absorb more light in the visible range, and this is important for photovoltaic and photocatalytic applications.     

Effect of strontium substitution on the composition and microstructure of sol–gel derived calcium phosphates

Sr-doped calcium phosphates have been prepared by sol–gel chemistry. All samples exhibit two phases: hydroxyapatite (HAp) and tricalcium phosphate (β-TCP). With respect to undoped sample, the Sr-doped samples exhibit higher proportion of β-TCP phase but the quantity appears to be quite independent of the doping level. To explain the mismatch with the nominal stoichiometry, the presence of amorphous CaO and SrO compounds have been postulated and their proportions evaluated. The insertion of Sr²⁺ ions in the two crystalline phases HAp and β-TCP is almost total for low doping levels but quite incomplete for the highest doping level. The majority of the inserted Sr²⁺ ions are in the β-TCP phase. Considering the acknowledged beneficial effect of Sr²⁺ on the bone regeneration process, the effective partial substitution of Sr in biphasic calcium phosphate makes these materials very interesting for clinical applications. The Sr-substituted HAp and β-TCP cell parameters agree fairly well with the Vegard’s law and Sr²⁺ ions substitute preferentially for Ca²⁺ in the Ca2 site for hydroxyapatite and in the Ca4 site for β-TCP. The microstructural parameters confirm the previous observation and give a new evidence of clear stabilizing effect of Sr²⁺ ions towards the β-TCP structure.