Aerosol assisted chemical vapor deposition using nanoparticle precursors: a route to nanocomposite thin films

Gold nanoparticle and gold/semiconductor nanocomposite thin films have been deposited using aerosol assisted chemical vapor deposition (CVD). A preformed gold colloid in toluene was used as a precursor to deposit gold films onto silica glass. These nanoparticle films showed the characteristic plasmon absorption of Au nanoparticles at 537 nm, and scanning electron microscopic (SEM) imaging confirmed the presence of individual gold particles. Nanocomposite films were deposited from the colloid concurrently with conventional CVD precursors. A film of gold particles in a host tungsten oxide matrix resulted from co-deposition with [W(OPh)(6)], while gold particles in a host titania matrix resulted from co-deposition with [Ti(O(i)Pr)(4)]. The density of Au nanoparticles within the film could be varied by changing the Au colloid concentration in the original precursor solution. Titania/gold composite films were intensely colored and showed dichromism: blue in transmitted light and red in reflected light. They showed metal-like reflection spectra and plasmon absorption. X-ray photoelectron spectroscopy and energy-dispersive X-ray analysis confirmed the presence of metallic gold, and SEM imaging showed individual Au nanoparticles embedded in the films. X-ray diffraction detected crystalline gold in the composite films. This CVD technique can be readily extended to produce other nanocomposite films by varying the colloids and precursors used, and it offers a rapid, convenient route to nanoparticle and nanocomposite thin films.     

纳米二氧化钒薄膜的制备及红外光学性能

采用双离子束溅射方法在Si3N4/SiO2/Si基底表面沉积氧化钒薄膜, 在氮气气氛下热处理获得二氧化钒薄膜. 利用X射线衍射(XRD)、扫描电子显微镜(SEM)和X射线光电子能谱(XPS)研究了热处理温度对氧化钒薄膜晶体结构、表面形貌和组分的影响, 利用傅里叶变换红外光谱(FT-IR)对二氧化钒薄膜的红外透射性能进行了测试分析. 结果表明, 所制备的氧化钒薄膜以非晶态V2O5和四方金红石结构VO2为主, 经400 ℃、2 h热处理后获得了(011)择优取向的单斜金红石结构纳米VO2薄膜, 提高热处理温度至450 ℃, 纳米结构VO2薄膜的晶粒尺寸减小. FT-IR结果显示,纳米VO2薄膜透射率对比因子超过0.99, 高温关闭状态下透射率接近0. 小晶粒尺寸纳米VO2薄膜更适合在热光开关器件领域应用.     

Vanadium(IV) oxide thin films on glass and silicon from the atmospheric pressure chemical vapour deposition reaction of VOCl3 and water

The dual source atmospheric pressure chemical vapour deposition (APCVD) reaction of VOCl₃ and H₂O was used to prepare thin films of vanadium oxides on glass and silicon substrates. The thin films were characterised by X-ray diffraction, Raman spectroscopy X-ray photoelectron spectroscopy and scanning electron microscopy. At reactor temperatures above 600 °C with a gas-phase excess of water over VOCl₃, vanadium(IV) oxide thin films were produced which show a thermochromic transition temperature of 67 °C. The APCVD process is directly compatible with high throughput float-glass production enabling the use of a thin film of VO₂ as an intelligent window coating. With reactor temperatures below 600 °C or with a gas-phase excess of VOCl₃ over water, V₂O₅ thin films were produced. Vanadium(IV) oxide thin films could also be prepared on silicon substrates from the APCVD reaction of VOCl₃ and H₂O, which opens up further technological applications for the APCVD of VO₂ thin films.     

Optical Properties of Sol-Gel Derived Vanadium Oxide Films

Vanadium oxide gels can be made from vanadate aqueous solutions or from vanadium alkoxides. The condensation of vanadic acid gives long ribbon-like oxide particles which macroscopically orient in the same direction in aqueous sols when their concentration is larger than 0.12 mol·l⁻¹. These anisotropic sols and gels should be considered as lyotropic nematic liquid crystals. Thick films in which ribbons align along the same direction can be deposited. These oriented coatings exhibit improved electrochemical properties as reversible cathodes for lithium batteries. Amorphous oxo-polymers are formed via the controlled hydrolysis of vanadium alkoxides. They allow the deposition of optically transparent thin films that exhibit interesting electrochromic properties and turn reversibly from yellow to green upon electrochemical reduction. Moreover these alkoxide derived films can be easily reduced into vanadium dioxide. These VO₂ thin films exhibit thermochromic properties and could be used as optical switches in the infrared. The transition temperature of these VO₂ films can be modified by doping the vanadium oxide with other cations.     

In situ formation and size control of gold nanoparticles into chitosan for nanocomposite surfaces with tailored wettability

The in situ formation of gold nanoparticles into the natural polymer chitosan is described upon pulsed laser irradiation. In particular, hydrogel-type films of chitosan get loaded with the gold precursor, chloroauric acid salt (HAuCl(4)), by immersion in its aqueous solution. After the irradiation of this system with increasing number of ultraviolet laser pulses, we observe the formation of gold nanoparticles with increasing density and decreasing size. Analytical studies using absorption measurements, atomic force microscopy, scanning electron microscopy, and X-ray photoelectron spectroscopy of the nanocomposite samples throughout the irradiation procedure reveal that under the specific irradiation conditions there are two competing mechanisms responsible for the nanoparticles production: the photoreduction of the precursor responsible for the rising growth of gold particles with increasing size and the subsequent photofragmentation of these particles into smaller ones. The described method allows the localized formation of gold nanoparticles into specific areas of the polymeric films, expanding its potential applications due to its patterning capability. The size and density control of the gold nanoparticles, obtained by the accurate increase of the laser irradiation time, is accompanied by the simultaneously controlled increase of the wettability of the obtained gold nanocomposite surfaces. The capability of tailoring the hydrophilicity of nanocomposite materials based on natural polymer and biocompatible gold nanoparticles provides new potentialities in microfluidics or lab on chip devices for blood analysis or drugs transport, as well as in scaffold development for preferential cells growth.     

Thin films composed of multiwalled carbon nanotubes, gold nanoparticles and myoglobin for humidity detection at room temperature.

Optically transparent and electrically conductive nanocomposite thin films consisting of multiwalled carbon nanotubes (MWCNTs), gold nanoparticles (GNPs) and myoglobin molecules that glue GNPs and MWCNTs together are fabricated for the first time on glass substrates from aqueous solution. The nanocomposite thin film is capable of varying its resistance, impedance or optical transmittance at room temperature in response to changes in ambient humidity. The conductometric sensitivity to relative humidity (RH) of the nanocomposite thin film is compared with those of the pure and Mb-functionalized MWCNT layers. The pure MWCNT layer shows a small increase in its resistance with increasing RH due to the effect of p-type semiconducting nanotubes present in the film. In contrast, a four times higher sensitivity to RH is observed for both the nanocomposite and Mb-functionalized MWCNT thin films. The sensitivity enhancement is attributable to swelling of the thin films induced by water absorption in the presence of Mb molecules, which increases the inter-nanotube spacing and thereby causes a further increase of the film resistance. A humidity change as low as DeltaRH=0.3 % has been readily detected by conductometry using the nanocomposite thin film.     

Morphology study of gold-chitosan nanocomposites

Gold nanoparticles were prepared in the presence of chitosan via reduction of HAuCl4 with sodium borohydride. The gold-chitosan nanocomposite was formed by adsorbing chitosan molecules onto the gold nanoparticle surfaces. The resulting gold nanoparticles were characterized by transmission electron microscopy and UV-vis spectroscopy. Morphology of gold-chitosan nanocomposite films was investigated by polarized optical microscopy. The morphology of chitosan crystal cast from the prepared nanocomposite was much different from that cast from chitosan solution due to the possible nucleation of gold nanoparticles. A branched-like structure or a cross-linked needle-like structure could be formed in nanocomposite films with different casting volumes.     

Spectral characterization of apatite formation on poly(2-hydroxyethylmethacrylate)-TiO2 nanocomposite film prepared by sol-gel process

Poly(2-hydroxyethylmethacrylate) films incorporated with titanium dioxide nanoparticles were successfully synthesized by an in situ sol-gel process. The in vitro bioactive properties of the films were assessed after immersion in simulated body fluid for up to 21 days through biomimetic method. Hydroxyapatite formation was observed on the surfaces of nanocomposites. This indicates that prepared composites are bioactive. Fourier transforms infrared spectroscopy, X-ray diffraction patterns, X-ray photoelectron spectroscopy and scanning electron microscope images confirm the hydroxyapatite formation on nanocomposite. The present study provides an analytical method for the assessment of titanium dioxide nanoparticles filled poly(2-hydroxyethylmethacrylate) polymer nanocomposites for biomedical applications.     

Low dielectric constant nanocomposite thin films based on silica nanoparticle and organic thermosets

Low dielectric constant (low-k) nanocomposite thin films have been prepared by spin coating and thermal cure of solution mixtures of one of two organic low-k thermoset prepolymers and a silica nanoparticle with an average diameter of about 8 nm. The electrical, the mechanical, and the thermomechanical properties of these low-k nanocomposite thin films have been characterized with 4-point probe electrical measurements, nanoindentation measurements with an atomic force microscope, and specular X-ray reflectivity. Addition of the silica nanoparticle to the low-k organic thermosets enhances both the modulus and the hardness and reduces the coefficient of thermal expansion of the resultant nanocomposite thin films. The enhancements in the modulus of the nanocomposite thin films are less than those predicted by the Halpin-Tsai equations, presumably due to the relatively poor interfacial adhesion and/or the aggregation of the hydrophilic silica nanoparticles in the hydrophobic organic thermoset matrices. The addition of the silica nanoparticle to the low-k organic thermoset matrices increases the relative dielectric constant of the resultant nanocomposite thin films. The relative dielectric constant of the nanocomposite thin films has been found to agree fairly well with an additive formula based on the Debye equation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1482–1493, 2007     

Preparation of a nanocomposite film from poly(diallydimethyl ammonium chloride) and gold nanoparticles by in-situ electrochemical reduction, and its application to SERS spectroscopy and sensing of ascorbic acid

A nanocomposite film is described that is composed of alternating layers of poly(diallydimethyl ammonium chloride) and gold nanoparticles that interact through electrostatic forces. The films of varying thickness were prepared by the layer-by-layer technique, and Au-NPs were generated by electrochemical reduction of hexachloroauric acid. The composite films were characterized by UV?Cvis spectroscopy, X-ray photoelectron spectroscopy, and cyclic voltammetry. Most nanocomposite films exhibit linear, uniform, and regular layer-by-layer growth during the process of formation. The films exhibit unique performance in terms of surface enhanced Raman scattering and electrocatalytic activitiy towards the oxidation of ascorbic acid.

Immobilization of biogenic gold nanoparticles in thermally evaporated fatty acid and amine thin films

We have recently demonstrated the biological synthesis of gold nanoparticles by the reduction of aqueous chloroaurate ions by the fungus Fusarium oxysporum and with extract of geranium (Pelargonium graveolens) leaf. In this paper, we demonstrate the immobilization of biogenic gold nanoparticles in lipid thin films deposited by thermal evaporation. The charge on the gold nanoparticles synthesized by both the fungus and the geranium plant extract is used to facilitate their immobilization in both anionic and cationic lipid thin films. A rough estimate of the isoelectric point of the proteins capping the gold nanoparticles synthesized using the fungus could be made by pH-dependent microgravimetry studies of the immobilization process. An interesting size and shape selectivity in the immobilized gold nanoparticles is observed in the lipid thin films. The biogenic gold nanoparticle-lipid composite films were characterized using quartz crystal microgravimetry, UV-vis absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and transmission electron microscopy.     

Gold nanoparticle embedded, self-sustained chitosan films as substrates for surface-enhanced Raman scattering

In this work, self-sustained, biocompatible, biodegradable films containing gold nanostructures have been fabricated for potential application in nanobioscience and ultrasensitive chemical and biochemical analysis. We report a novel synthesis of gold nanoparticles mediated by the biopolymer chitosan. Self-supporting thin films are formed from the resultant gold-chitosan nanocomposite solutions and characterized by UV-visible surface plasmon absorption, transmission electron microscopy, atomic force microscopy, infrared absorption, and Raman scattering measurements. Results demonstrate control over the size and distribution of the nanoparticles produced, which is promising for several applications, including the development of biosensors. As a proof of principle, we demonstrate that gold-chitosan films can be employed in trace analysis using surface-enhanced Raman scattering.     

Electrochemical synthesis of gold nanoparticles on the surface of multi-walled carbon nanotubes with glassy carbon electrode and their application

Gold nanoparticles on the surface of multi-walled carbon nanotubes with glassy carbon electrode were prepared using electrochemical synthesis method. The thin films of gold Nanoparticles/multi-walled carbon nanotubes were characterized by scanning electron microscopy, powder X-ray diffraction, and cyclic voltammetry. Electrochemical behavior of adrenaline hydrochloride at gold nanoparticles/multi-walled carbon nanotube modified glassy carbon electrode was investigated. A simple, sensitive, and inexpensive method for determination of adrenaline hydrochloride was proposed.     

Robust multilayer thin films containing cationic thiol-functionalized gold nanorods for tunable plasmonic properties

Gold nanorods have great potential in a variety of applications because of their unique physical properties. In this article, we present the layer-by-layer (LbL) assembly of thin films containing positively charged gold nanorods that are covalently functionalized by cationic thiol molecules. The cationic gold nanorods are uniformly distributed in ultrathin nanocomposite LbL thin films. We studied the collective surface plasmon resonance coupling in the LbL films via UV-visible spectroscopy and evaluated their application in the surface-enhanced Raman scattering detection of rhodamine 6G probe molecules. Furthermore, we successfully manufactured freestanding nanoscale thin films containing multilayers of gold nanorods with a total thickness of less than 50 nm. The surface morphology and their optical and mechanical properties were systematically investigated, and the polycationic gold nanorods were found to play an important role in manipulating the properties of the nanocomposite thin films. Our findings reveal that such nanorods are excellent building blocks for constructing functional LbL films with tunable plasmonic behavior and robust mechanical properties.     

Electroless gold island thin films: photoluminescence and thermal transformation to nanoparticle ensembles

Electroless gold island thin films are formed by galvanic replacement of silver reduced onto a tin-sensitized silica surface. A novel approach to create nanoparticle ensembles with tunable particle dimensions, densities, and distributions by thermal transformation of these electroless gold island thin films is presented. Deposition time is adjusted to produce monomodal ensembles of nanoparticles from 9.5 +/- 4.0 to 266 +/- 22 nm at densities from 2.6 x 1011 to 4.3 x 108 particles cm-2. Scanning electron microscopy and atomic force microscopy reveal electroless gold island film structures as well as nanoparticle dimensions, densities, and distributions obtained by watershed analysis. Transmission UV-vis spectroscopy reveals photoluminescent features that suggest ultrathin EL films may be smoother than sputtered Au films. X-ray diffraction shows Au films have predominantly (111) orientation.     

乳液聚合法制备纳米金/聚苯乙烯复合粒子

以氯金酸为前驱体,十二烷基硫醇和硼氢化钠分别作为稳定剂和还原剂,采用相转移法制备了单分散的金纳米粒子.将金纳米粒子通过乳液聚合的方法制备了纳米金/聚苯乙烯复合粒子.通过紫外-可见吸收光谱(UV-Vis)研究了纳米金和纳米金/聚苯乙烯复合粒子的光吸收特性,使用傅立叶变换红外光谱(FT-IR)、X射线衍射(XRD)、透射电子显微镜(TEM)和动态光散射(DLS)对产物的组成、晶体结构、形貌、以及粒径进行了表征.结果表明,复合粒子为粒径分布较窄的球形,其中的金纳米粒子为面心立方结构.热失重分析(TGA)说明制备的纳米金/聚苯乙烯复合粒子具有很好的热稳定性.     

Electrocatalytic oxidation of nitric oxide at TiO2–Au nanocomposite film electrodes

Structured films of TiO₂ (anatase) nanoparticles (ca. 6 nm diameter) and gold nanoparticles (nominal 20 nm diameter) are formed via a layer-by-layer deposition procedure. TiO₂ nanoparticles are deposited with a Nafion polyelectrolyte binder followed by calcination to give a mesoporous thin film electrode. Gold nanoparticles are incorporated into this film employing a poly(diallyldimethylammonium chloride) polyelectrolyte binder followed by calcination to give a stable mesoporous TiO₂–gold nanocomposite. This methodology allows well-defined and structured films to be formed which are re-usable after a 500 °C heat treatment in air.Electrochemical experiments are performed in aqueous KCl and buffer solutions and for the oxidation of nitric oxide, NO, and nitrite in phosphate buffer solution. It is shown that the NO oxidation occurs as a highly effective electrocatalytically amplified process at the surface of the gold nanocomposite probably with co-evolution of oxygen, O₂. In contrast, the oxidation of nitrite to nitrate occurs at the same potential but without oxygen evolution. A mechanistic scheme for the amplified NO detection process is proposed.     

Upconversion and Phase Transition Characteristics in Erbium(III)- and Ytterbium(III)-Codoped Vanadium(IV) Oxide

Vanadium(IV) dioxide has emerged as a promising thermochromic material for smart window application through metal–insulator transition, which simultaneously involves an abrupt change in optical, electrical, and magnetic properties. Here, Er³⁺ or Yb³⁺-codoped vanadium(IV) dioxide has been prepared by a hydrothermal and annealing process. The structure, metal–insulator transition, and upconversion luminescence characterizations have been evaluated using X-ray diffraction, differential thermal analysis, and fluorescence spectral analysis. The samples exhibit unique properties, including enhancing the intensity of upconversion emission, decreasing the metal–insulator transition temperature to 41.4°C, and emitting bright green upconversion emission along with extremely weak emission in the red region under 980?nm excitation. Moreover, green upconversion luminescence intensity increased by an order of magnitude from the low-temperature monoclinic structure of vanadium(IV) dioxide to the high-temperature rutile structure of vanadium(IV) dioxide for the first time, which will pave a new pathway for researching the application of photoluminescence in smart materials.     

氨基功能化有序介孔Si02薄膜组装Au纳米粒子复合材料的可调色散性质

以聚环氧乙烷-聚环氧丙烷-聚环氧乙烷(P123)为模板剂,采用共溶胶的蒸发诱导自组装方法制备了氨基功能化介孔SO2薄膜,然后利用氯金酸(HAUCl4)与介孔SiO2薄膜孔道内壁的氨基之间的中和反应组装Au纳米粒子,制备得到Au/SiO2纳米复合材料.用TEM,XRD和UV-Vis光谱对材料进行了测试.结果表明,无水乙醇...     

The microstructure and properties of thin WO3 films modified by gold

Direct current magnetron sputtering of a metallic W + Au target or high-frequency magnetron sputtering of WO₃ + Au oxide targets was used to prepare thin (about 100 nm) nanocrystalline WO₃ films with the addition of gold (disperse layers of catalytic gold were additionally deposited on the surface of films). The composition and micromorphology of the surface of films and the electrical and gas sensitive characteristics of nitrogen dioxide sensors were studied to determine the mechanism of the influence of gold on the properties of WO₃ films. The films were shown to contain the β-WO₃ orthorhombic and γ-WO_2.72 monoclinic phases and gold particles. The presence of the nonstoichiometric γ-WO_2.72 phase was shown to increase the concentration of oxygen vacancies in films and decrease the resistance of sensors to 1–2 MΩ. Gold nanoparticles 9–15 nm in size segregated on the surface of semiconductor crystallites and increased the response of sensors to NO₂. The conclusion was drawn that deposited catalytic gold layers increased the response to traces of nitrogen dioxide.