Estimation of Corrosion Rate of Bulk and Powder Ni–Re Alloy

The corrosion current density of Ni–Re alloy (15.8 wt % Re) was estimated using recently developed method of compensating additives. The alloy was fabricated by the electrodeposition in the form of bulk specimen and the powder prepared of this specimen. The electrodeposition was performed in stirred 5 × 10^–3 M HCl solution. The method enabled us to determine the corrosion rate with no external polarization of studied specimens and at virtually constant pH value. A specific electrochemical activity of powder surface was estimated by comparing the corrosion currents of bulk and powder specimens. The powder was intended for testing its catalytic activity in several electrochemical reactions.     

Effect of Re addition on the crystallization,heat treatment and structure of the Cu–Ni–Si-Cr alloy

Differential scanning calorimetry (DSC) was used to investigate the thermal behavior and non-isothermal crystallization kinetics of the Fe₆₇Nb₅B₂₈ metallic glasses prepared by melt-spinning method. DSC traces exhibit that the crystallization takes place through a single exothermic reaction, and it processes a good thermal stability in thermodynamics. The activation energies for nucleation and grain growth processes were calculated to be 536 ± 22 and 559 ± 20 kJ mol^?1 by Kissinger equation, respectively, and 551 ± 24 and 574 ± 20 kJ mol^?1 by Ozawa equation, respectively. It means that the grain growth process is more difficult than the nucleation process. The variation of local Avrami exponent n(x) with crystallized fraction x demonstrates that the crystallization mechanism varies at different stages. The n(x) is larger than 2.5 at the initial stage of 0 < x < 0.3, implying a mechanism of diffusion-controlled three-dimensional growth with increasing nucleation rate. The n(x) decreases from 2.5 to 1.5 in the range of 0.3 < x < 0.65, suggesting that the crystallization belongs to three-dimensional nucleation and grain growth with decreasing nucleation rate. And n(x) lies between 1.0 and 1.5 in the range of 0.65 < x < 0.95, indicating that the crystallization corresponds to the growth of particles with an appreciable initial volume. Low-temperature annealing corresponds to the precipitation of α-Fe, Fe₂B, and Fe₂₃B₆ phases, and further annealing leads to the formation of α-Fe, Fe₂B, and FeNbB phases. The magnetic properties in relation to microstructure change of the Fe₆₇Nb₅B₂₈ metallic glasses are discussed.     

Studies of chemical–catalytic formation of Ni–Re (Mo,W)–B alloys

The paper briefly reviews the studies of the processes of formation of Ni–Re–B, Ni–Mo–B, and Ni–W–B triple alloys using the method of chemical–catalytic reduction of metal ions and their properties.     

Synthesis and Re—refinement of Cu3PSe4

1 INTRODUCTION The chemistry of mixed 15/16 main group compounds has attracted great attentions over the last years[1]. The metal chalcogenophosphides synthesized by solid state reactions[2] are the potential candidates for a wide range of applications such as semiconducting properties, two-dimensional magnetic behavior, anisotropy of conductivity and charge density waves. Some of these compounds are of lamellar structure, which are good materials for the investigation of intercalatio…     

Bubble points of hydrogen chloride–water–isopropanol and hydrogen chloride–water–isopropanol–benzene systems and liquid–liquid equilibria of hydrogen chloride–water–benzene and hydrogen chloride–water–isopropanol–benzene systems

Bubble points of the HCl–water–isopropanol and the HCl–water–isopropanol–benzene systems and liquid–liquid equilibria (LLE) of the HCl–water–benzene and the HCl–water– isopropanol–benzene systems were measured at 25–85°C and 30–70°C, respectively. The electrolyte nonrandom two-liquid model proposed by Chen et al. [C.-C. Chen, H.I. Britt, J.F. Boston, L.B. Evans, AIChE J. 28 (1982) 588–596] can satisfactorily correlate bubble points and liquid–liquid equilibria of the present mixed-solvent electrolyte systems over the entire range of temperature and concentrations using only binary adjustable parameters.     

Electrochemical and structural characterization of sputter-deposited Mg–Nb and Mg–Nb–Al–Zn alloy films

Nanocrystalline Mg–Nb and Mg–Nb–Al–Zn alloy films were deposited by dc magnetron sputtering on glass and quartz substrates in a wide range of niobium concentrations from 6 to 80 at.%. Structural, electrochemical and corrosion properties of the films were studied by X-ray diffraction, dc voltammetry, electrochemical impedance spectroscopy and electrochemical quartz crystal microbalance. Development of body-centred cubic Nb structure in the Mg–Nb alloy matrix yielded the effects of lattice contraction, grain refining and electrochemical passivity. The measurements showed high corrosion resistance of the films in alkaline solutions when niobium content was one third or more. An increased corrosion resistance was achieved by introducing minor amounts of Al (ca. 2 at.%). In particular, such Al effect was pronounced at lower Nb concentrations (20 to 30 at.%). Semiconductor properties of spontaneously formed oxide on Mg–Nb alloy were studied by Mott–Schottky plots, which indicated highly doped n-type oxide structures on Mg–Nb surface. The paper fills some gap in understanding of niobium–magnesium systems, which show potential for applications in hydrogen storage, switchable mirrors and corrosion protection.     

Electrochemical and microgravimetric characterization of magnetron-sputtered Fe–Cr–Ni–Ta and Fe–Cr–Ni alloy films in neutral and strongly acidic media

The Fe–Cr–Ni and Fe–Cr–Ni–Ta alloy films were deposited on quartz substrates by magnetron-sputtering using targets of AISI 316 stainless steel and in combination with pure tantalum. The conventional melting of the Fe–Cr–Ni–Ta alloy formed is virtually impossible because the melting point of tantalum is higher than the boiling points of the other components. Elemental content of the films was determined by XPS analysis. Corrosion behaviour of both alloy films was studied in 5% NaCl and 10 M HCl by electrochemical quartz crystal microgravimetry (EQCM), electrochemical impedance spectroscopy (EIS) and dc-voltammetry. The corrosion resistance of Fe–Cr–Ni–Ta appeared to be significantly higher than that of Fe–Cr–Ni in both neutral (5% NaCl) and strongly acidic (10 M HCl) media. The Fe–Cr–Ni–Ta specimen exhibited an extremely high corrosion resistance in 10 M HCl, where the corrosion rates were about one order of magnitude lower than those of Fe–Cr–Ni in neutral solution. EQCM measurements in NaCl solution indicated accumulation of corrosion products on the Fe–Cr–Ni–Ta surface, which was evident from a distinctive increase in electrode mass. By contrast, the mass of the tantalum-free alloy film decreased with a constant rate, which indicated alloy dissolution to prevail. The corrosion current calculated from the mass decrease was in good agreement with that derived from voltammetric measurements. The EQCM data showed that the corrosion resistance of the Fe–Cr–Ni–Ta alloy film in 10 M HCl was about two orders of magnitude higher than that of the Fe–Cr–Ni.     

The density and surface tension of In–Sn and Cu–In–Sn alloys

Abstract  

The density and surface tension of binary In–Sn and ternary Cu–In–Sn alloys have been measured by a sessile-drop method. Decrease of the density and of the surface tension was observed with rising temperature. With increased Sn content in the alloys, the density increased while the surface tension reduced slightly. Addition of Cu could significantly increase the density and surface tension in the Cu–In–Sn system. The surface tension of the Cu–In–Sn alloys was also calculated by means of Butler’s equation, and compared with experimental values, showing good agreement.     

Trimetallic Nickel–Lanthanum and Nickel–Gadolinium Metallomesogens

Adducts were formed between a mesomorphic Ni(salen) complex [salen=2,2′-N,N′-bis(salicylidene)ethylenediamine] with six terminal alkoxy chains and a lanthanide nitrate (Ln=La, Gd). Different alkoxy chain lengths were used: OC¹²H²⁵, OC¹⁴H²⁹, OC¹⁶H³³ and OC¹⁸H³⁷. Trinuclear nickel–lanthanum and nickel–gadolinium complexes [Ln(NO³)³{Ni(salen)}²] were obtained. The compounds exhibit a wide-temperature-range hexagonal columnar mesophase (Col^H) with rather low melting points. The mesophase stability ranges of both the parent nickel complexes and the nickel–lanthanide complexes decrease with increasing chain length. A decrease in the mesophase stability range over the lanthanide series was also observed. The results are compared with those of similar copper–lanthanide complexes. A marked difference is the higher thermal stability of the nickel–lanthanide complexes in comparison with the copper–lanthanide complexes.     

Z- and E-selective Horner–Wadsworth–Emmons reactions

In the present work, we determined and evaluated the stereochemical outcome of the Horner–Wadsworth–Emmons (HWE) reaction of 2-oxoalkylphosphonates with different ester functions (bis(2,2,2-trifluoroethyl), 2,2,2-trifluoroethyl methyl, dimethyl) and side chains (aliphatic, aromatic) with three different aldehydes (benzaldehyde, THP- and PPB-protected Corey aldehydes) under two reaction conditions. The “trans” protocol is generally used in the E-selective HWE reactions, while “cis” protocol promotes the Z-selectivity.     

Electrochemical reactivity of Li–Mn–O and Li–Fe–Mn–O spinels

Electrochemical reductive dissolution of Li–Mn–O and Li–Fe–Mn–O spinels and Li⁺ extraction/insertion in these oxides were performed using voltammetry of microparticles. Both electrochemical reactions are sensitive to the Fe/(Fe+Mn) ratio, specific surface area, Li content in tetrahedral positions, and Mn valence, and can be used for electrochemical analysis of the homogeneity of the elemental and phase composition of synthetic samples. The peak potential (E _P) of the reductive dissolution of the Li–Mn–O spinel is directly proportional to the logarithm of the specific surface area. E _P of Li–Fe–Mn–O spinels is mainly controlled by the Fe/(Fe+Mn) ratio. Li⁺ insertion/extraction can be performed with Mn-rich Li–Fe–Mn–O spinels in aqueous solution under an ambient atmosphere and it is sensitive to the regularity of the spinel structure, in particularly to the amount of Li in tetrahedral positions and the Mn valence. Electronic Publication     

Thermodynamic and surface properties of Ge–Ga and Ge–Sb liquid alloys

Thermodynamic and surface properties of Ge–Ga and Ge–Sb liquid alloys have been studied using statistical mechanical formulations based on complex formation and that based on the concept of layered structure near the interface. The study showed that low level of complex formation of the form Ge _{2 Sb} exists in Ge–Sb toward the Ge-rich end of the concentration range and the surface properties of Ge–Ga are almost equal to their corresponding bulk equivalent.     

Application of CE–ICP–MS and CE–ESI–MS in metalloproteomics: challenges,developments, and limitations

Application of capillary electrophoresis (CE) as a high-resolution separation technique in metalloproteomics research is critically reviewed. The focus is on the requirements and challenges involved in coupling CE to sensitive element and molecule-specific detection techniques such as inductively coupled plasma mass spectrometry (ICP–MS) or electrospray ionisation mass spectrometry (ESI–MS). The complementary application of both detection techniques to the structural and functional characterisation of metal-binding proteins and their structural metal-binding moieties is emphasised. Beneficial aspects and limitations of mass spectrometry hyphenated to CE are discussed, on the basis of the literature published in this field over the last decade. Recent metalloproteomics applications of CE are reviewed to demonstrate its potential and limitations in modern biochemical speciation analysis and to indicate future directions of this technique.     

Hydrogen Evolution on Catalytically Active Electrodeposited Ni–Re Alloy: Electrochemical Impedance Study

Hydrogen evolution reaction on the catalytically active Ni–Re alloy is studied by the method of electrochemical impedance. The alloy was fabricated by the electrodeposition from the ammonium—citrate solutions. The experiments were performed in the 0.1 M sodium hydroxide solution. Based on the analysis of equivalent circuits, it is found that the absorption of hydrogen atoms on the Ni–Re cathode is controlled by diffusion. The parameters of structural elements of equivalent electric circuits are calculated, and the effect of cathodic overpotential on these parameters is analyzed.     

HS–SPME–GC–MS for the Quantitation and Chiral Characterization of Camphor and Menthol in Creams

A GC–MS method is proposed for the analysis of camphor and menthol in “over-the-counter” (OTC) products. Sample preparation was achieved by head-space solid phase microextraction using a polydimethylsiloxane fibre. GC analysis was performed using a Phenomenex ZB-5 column and a temperature program was adopted. The method was validated by studying linearity (range 0.1–15.0% w/w), accuracy, reproducibility and sensitivity. Applications were directed to the determination of the active ingredients in four different OTC-products; the mean recoveries were in the ranges 91.30–99.74% and 94.34–102.89% for camphor and menthol, respectively and the LOD was in the order of 0.005% (w/w). Other important terpenoids (α- and β-pinene, 1,8-cineole, menthone, isomenthone, α-terpineole, t-cinnamaldehyde, eugenole) were identified by mass spectra and Kovats retention indices and quantified by peak area normalization to 100%. Further information for a comprehensive characterization of the OTC-products was achieved by the GC chiral analysis on a Cyclosil B capillary column.     

Iron–cobalt and iron–cobalt–nickel nanowires deposited by means of cyclic voltammetry and pulse-reverse electroplating

Metal nanowires composed of Fe–Co and Fe–Co–Ni alloys were successfully prepared by means of cyclic voltammetry (CV) and pulse-reverse (PR) electroplating techniques from acidic metal chloride solutions. The anodic dissolution process in the CVs or in the reverse electroplating period was found to be the key factor influencing the formation of metal nanowires. The addition of nickel into the Fe–Co alloy was found to extend the diameter of these nanowires. The morphology and crystalline information of these alloy deposits prepared by CV and PR deposition techniques were obtained from the field-emission scanning electron microscopic (FE-SEM) photographs and X-ray diffraction (XRD) patterns, respectively.     

On hydrolysis of Ba–Bi–O and K–Ba–Bi–O oxide systems

Fundamentally different behavior of Ba–Bi–O (Ba : Bi = 11 : 4, 1 : 1, 2: 3, and 1 : 5 mol/mol) and K_nBa_mBi_m+nO_y (m = n = 1, 2,...; exhibiting superconducting properties with T_c = 28–32 K) oxides and BaO₂ in hydrolysis reactions has been revealed by means of potentiometry and chemical analysis. Products of the oxides treatment with water do not contain H₂O₂, evidencing the absence of peroxide ions in their structure. The perovskite-type barium-bismuth(III) oxides are completely hydrolyzed into Ba(OH)₂ and Bi₂O₃ at room temperature.