聚碳酸1,2-丙二酯/聚琥珀酸丁二酯/邻苯二甲酸二烯丙酯共混体系的研究

采用熔融共混的方法制备了聚碳酸1,2-丙二酯(PPC)/聚琥珀酸丁二酯(PBS)共混物和PPC/PBS/DAOP(邻苯二甲酸二烯丙酯)增塑共混物,对共混物的相容性、热性能、结晶性和物理机械性能进行了初步研究.研究结果表明PPC/PBS共混物为不相容体系,PPC对PBS的结晶度影响很小;PBS的加入提高了共混物的起始热分解温度(Td-5%),当共混物中PBS含量从10%增加到90%时,共混物的Td-5%可分别增加15℃到59℃.DAOP对PPC/PBS共混物有增塑作用,当PPC/PBS/DAOP的比例从30/70/0变化到30/70/30时,共混物玻璃化转变温度(Tg)下降了36.9℃.与PPC/PBS共混物相比,组成优化的DAOP增塑共混物PPC/PBS/DAOP(PPC/PBS/DAOP=30/70/5)的断裂伸长率和断裂能最大可提高31倍和34倍,分别达到655.1%和3.4 J/mm2,因此引入DAOP尽管使共混材料的热稳定性有所下降,但拓宽了PPC/PBS共混材料的使用温度窗口.     

氨酯化合物对聚碳酸1,2-丙二酯的同时增韧和增强研究

采用非异氰酸酯路线合成了1,6-六亚甲基二氨基甲酸羟异丙酯(BPU),分子量为320.利用熔融共混方法制备了聚碳酸1,2-丙二酯(PPC)/BPU共混物.研究发现BPU与PPC间有较好的相容性,随着BPU含量的增加,共混体系的起始热分解温度(Td.5％)可分别增加24～33℃,共混物韧性也显著提高,断裂伸长率最大可增至...     

聚乳酸与聚丙撑碳酸酯共混体系的性能

采用熔融共混的方法制备了聚乳酸(PLA)/聚丙撑碳酸酯(PPC)共混物。DSC测试结果表明,纯PLA和PPC的玻璃化转变温度分别为54和37℃,不同组成的PLA/PPC共混物有2个明显的玻璃化转变温度,且与纯PLA和PPC的玻璃化转变温度相对应,说明二者是不相容体系。力学测试结果表明,当PPC质量分数超过20%时,可以看到明显的屈服点。共混物在拉伸过程中也有明显的颈缩、应力发白现象,表明随着PPC含量增加,PLA/PPC共混物由典型的脆性断裂向韧性转变。随着PPC含量的增加,共混物模量降低,断裂伸长率增加,当PPC质量分数为50%时,共混物的断裂伸长率达到最大值62%。共混物的粘度可在很宽的范围内予以调控,以满足不同加工的需要。     

弹性体偶联剂结构对PVC/PPC性能的影响

NBR－PPC弹性体偶联剂能促进PPC（聚丙撑碳酸酯）与PVC（聚氯乙烯）之间的相容性，改善共混物的力学性能，并在共混体系中产生轻度交联。偶联剂组成在NBR／PPC比例为70／30，NBR（丁腈橡胶）含腈量为34％，BPO过氧化苯甲酸用量为2．5份时，共混物的综合力学性能最佳，但偶联剂预先硫化时间不宜过长．     

共混方法对聚氯乙烯/聚丙撑碳酸酯相容性影响

本文分别用溶液法和熔融法制得聚氯乙烯（PVC）与聚丙撑碳酸酯（PPC）共混试样，用DSC证明PVC／PPC共混物不相容，但它们不相容的程度受分子量、共混比例等因素的影响，并根据玻璃化转变温度（Tg）计算出溶液共混试样PPC富相中PVC的重量百分含量。NBR／PPC弹性体作偶联剂对PVC／PPC共混体系具有较好的增容作用，共混物中PPC的用量及分子量对共混体系性能有一定的影响。     

聚[(双-甘氨酸乙酯)膦腈]/聚酯共混相容性研究

采用溶液混合法制备了聚[(双－甘氨酸乙酯）膦腈]（PGP）与丙交酯均聚物（PLA）或丙交酯／乙交酯共聚物（PLGA）的共混体系，利用示差扫描量热仪、傅里叶红外光谱仪和相差显微镜研究了两体系的共混相容性。实验结果表明，PGP与PLA不相容，但通过氢键相互作用可与PLGA达到部分相容，且PGP／PLGA的共混相容性随着PLGA含量的增加而有所改善。     

聚2,5-呋喃二甲酸乙二醇酯/聚丁二酸丁二醇酯共混物的制备与表征

通过熔融共混制备了聚2,5-呋喃二甲酸乙二醇酯(PEF)/聚丁二酸丁二醇酯(PBS)共混物,探究了制备PEF/PBS共混物的影响因素,考察了共混温度、共混时间、螺杆转速、共混比例对PEF/PBS共混物力学性能的影响因素,并用示差扫描量热仪、热失重、扫描电子显微镜等技术手段对其热性能和相容性进行了表征。 结果表明,当PBS的含量为15%、共混温度为230 ℃,共混时间为90 s、螺杆转速为150 r/min时,为最佳共混制备条件,此时相容性最好,热性能良好,冲击强度和拉伸强度最大,冲击强度相对纯PEF提高了6倍,拉伸强度提高了近20%,从而大幅提高了PEF的冲击强度,有效地增强了PEF的抗冲击韧性。 这些工作为这一生物基聚酯材料的应用提供了可能。     

水辅助加工法制备聚丙撑碳酸酯/淀粉共混物

分别采用普通熔融共混法和水辅助加工法,制备了具有不同共混形态的聚丙撑碳酸酯(PPC)/淀粉共混物,并研究了淀粉分散形态对共混物的玻璃化转变温度(Tg)、流变以及力学性能的影响。研究结果表明,采用普通熔融共混法时,淀粉未发生糊化,并以原颗粒状分散于基体中;而采用水辅助加工法时,淀粉发生糊化,并在挤出过程中原位形成纤维结构。当淀粉以纤维形式分散于PPC基体中时,其与PPC间的界面接触面积显著增加,二者的相互作用增强,PPC/淀粉共混物的Tg、储能模量以及复合黏度显著提高。力学性能测试结果表明,当淀粉质量分数为30%,采用水辅助加工法制备的PPC/淀粉共混物的拉伸模量相比于纯PPC提高了67.7%。     

脂肪族聚碳酸酯(PPC)与聚乳酸(PLA)共混型生物降解材料的热学性能、力学性能和生物降解性研究

通过溶液浇铸法制备了脂肪族聚碳酸酯与聚乳酸的共混物(PPC/PLA).采用示差热分析(DSC)和热重分析(TG)研究了材料的热性能.采用拉伸力学试验研究了共混物的力学性能.通过土壤悬浊拟环境培养降解实验法和扫描电子显微镜分析(SEM)对共混材料的生物降解性能进行了研究.实验结果表明,随着PPC含量的增加,共混物的拉伸强度和杨氏模量降低,而生物降解速率却显著提高.但是,在一定的降解时间内,某些比例共混物的降解速率比100%PPC还要快.综合分析表明,PPC/PLA是力学性能和降解性能可以互补的共混体系.     

共混水凝胶：3.苯乙烯—丙烯酰胺共聚物／聚（甲基丙烯酸β—羟乙酯）共…

用自由基溶液聚合的方法制备了聚（甲基丙烯酸β－羟乙酯）（ＰＨＥＭＡ）和一系列不同组成的苯乙烯－丙烯酰胺共聚物（ＰＳＡｍ）。利用ＤＳＣ，ＩＲ方法研究了ＰＳＡｍ／ＰＨＥＭＡ共混体系的相容性。观察到不同组成的ＰＳＡｍ与ＰＨＥＭＡ等重量比混合时，只有Ａｍ含量在４７－５７ｍｏｌ％范围内的ＰＳＡｍ与ＰＨＥＭＡ的共混物相容，即共混体系表现出一个“ｍｉｓｃｉｂｉｌｉｔｙ ｗｉｎｄｏｗ”。应用平均场理论计算了上述共     

Mechanical,thermal and rheological properties and morphology of poly (lactic acid)/poly (propylene carbonate) blends prepared by vane extruder

In this study, the poly (lactic acid) (PLA) and poly (propylene carbonate) (PPC) blends with different compositions were prepared by a novel vane extruder based on elongation rheology. The mechanical properties, morphologies, crystallization behavior, thermal stability, and rheological properties of the blends were investigated. Mechanical test showed that PLA could be toughened by PPC to some extent, and the impact strength of the PLA was maximized when PPC content was about 30%. Differential scanning calorimetry analysis revealed that PPC had little effect on the melting process, the crystallization behavior of PLA component in the blend was improved, and the cold crystallizability of PLA decreased with the increase of PPC content when the PPC content was less than 50%. Thermogravimetry analysis showed that the thermal stability of the blends was improved by compounding with PLA. Scanning electron microscope showed that the dispersion of PLA droplets in PPC matrix was better than that of PPC droplets in PLA matrix. Rheological test showed that the melt viscosity of the pure PLA and the blend with 10% PPC was insensitive to shear rate, and the blends melt appeared shear thinning phenomenon with the increase of PPC content. It also showed that the blends microstructure changed with the addition of PPC and the blends with PPC content in a certain range had similar stress relaxation mechanism. Copyright © 2016 John Wiley & Sons, Ltd.     

氯化聚丙撑碳酸酯增容聚丙撑碳酸酯/秸秆粉复合材料的制备及性能

聚丙撑碳酸酯(PPC)是一种新型热塑性生物降解材料,但其热性能及力学性能较差,应用受到限制。以秸秆粉这种农作物副产品作为增强体改性PPC,既可以提高PPC的力学性能同时又可开发利用秸秆资源。氯化聚丙撑碳酸酯(CPPC)是聚丙撑碳酸酯(PPC)经过氯化得到的,对天然纤维表面具有良好的浸润性和粘结性。本文以CPPC为增容剂,通过熔融共混法制备了PPC/秸秆粉复合材料。采用扫描电子显微镜(SEM)、拉伸实验、动态力学性能测试(DMA)及转矩流变仪对复合材料的结构及性能进行了表征,重点考察了CPPC的添加量对复合材料力学和流变性能的影响。结果表明,当CPPC质量分数为1.8%时,可使添加质量分数为30%秸秆粉的PPC复合材料拉伸强度提高38%,模量提高30%。同时,CPPC的引入使复合材料的粘度下降,改善了PPC/秸秆粉复合材料的加工性能。因此,作为增容剂的CPPC为制备高性能PPC/天然纤维复合材料提供了新的解决办法。     

偶联剂对聚氯乙烯－聚丙撑碳酸酯共混体系力学性能的影响

偶联剂对聚氯乙烯－聚丙撑碳酸酯共混体系力学性能的影响王胜杰，黄玉惠，丛广民（中国科学院广州化学研究所广州５１０６５０）关键词聚氯乙烯，聚丙撑碳酸酯，偶联剂，丁腈胶，过氧化苯甲酰，共混聚氯乙烯（ＰＶＣ）是用量巨大的通用塑料，其软性制品需用大量的增塑剂，...     

Thermal,mechanical and rheological properties of biodegradable poly(propylene carbonate) and poly(butylene carbonate) blends

Poly(propylene carbonate)(PPC) was melt blended in a batch mixer with poly(butylene carbonate)(PBC) in an effort to improve the toughness of the PPC without compromising its biodegradability and biocompatibility. DMA results showed that the PPC/PBC blends were an immiscible two-phase system. With the increase in PBC content, the PPC/PBC blends showed decreased tensile strength, however, the elongation at break was increased to 230% for the 50/50 PPC/PBC blend. From the tensile strength experiments, the Pukanszky model gave credit to the modest interfacial adhesion between PPC and PBC, although PPC/PBC was immscible. The impact strength increased significantly which indicated the toughening effects of the PBC on PPC. SEM examination showed that cavitation and shear yielding were the major toughening mechanisms in the blends subjected the impact tests. TGA measurements showed that the thermal stability of PPC decreased with the incorporation of PBC. Rheological investigation demonstrated that the addition of PBC reduced the value of storage modulus, loss modulus and complex viscosity of the PPC/PBC blends to some extent. Moreover, the addition of PBC was found to increase the processability of PPC in extrusion. The introduction of PBC provided an efficient and novel toughened method to extend the application area of PPC.     

Blends of Poly（lactic acid） with Thermoplastic Acetylated Starch

Blends of poly(lactic acid)(PLA) and thermoplastic acetylated starch(ATPS) were prepared by means of the melt mixing method. The results show that PLA and ATPS were partially miscible, which was confirmed with the measurement of Tg by dynamic mechanical analysis(DMA) and differrential scanning calorimetry(DSC). The mechanical and thermal properties of the blends were improved. With increasing the ATPS content, the elongation at break and impact strength were increased. The elongation at break increased from...     

高分子量聚对二氧环己酮改进聚DL-乳酸柔韧性的研究

为了提高DL-聚乳酸(PDLLA)的柔韧性,将10～20wt%不同比例的由本课题组自主合成的高分子量聚对二氧环己酮(PPDO)加入到PDLLA基体中,对共混物的微观两相形态、力学性能、热学性能和表面性质、降解性能等物化性质进行了研究.实验结果表明,PPDO加入后,在PDLLA/PPDO共混物的柔韧性得到显著提高的同时,共混物表面亲水性相应提高,降解速率也随之加快.     

Thermal,Rheological and Mechanical Properties of Biodegradable Poly(propylene carbonate)/Epoxidized Soybean Oil Blends

Biodegradable poly(propylene carbonate) (PPC)/epoxidized soybean oil (ESO) blends with different component ratios were prepared by melt blending to improve the performance of PPC.The phase morphology,thermal properties,rheological properties and mechanical properties of the blends were investigated in detail.SEM examination revealed good interfacial adhesion between PPC matrix and ESO.According to DSC and DMA,as the content of ESO increased,the glass transition temperature of the PPC component increased,indicating that there was a strong interfacial interaction between the PPC matrix and ESO.The interracial interaction may be caused by ring-opening reaction between the hydroxyl end groups of PPC and the epoxy groups of ESO,which restricted the chain movement of PPC matrix.The disappearance of the epoxy groups in FTIR indicated that the interfacial interaction between the two phases was due to the ring-opening reaction between PPC and ESO.With the addition of ESO,the thermal stabilities were enhanced.With the increasing ESO content,the modulus gradually decreased.However,the strength at yield,the strength at break and the elongation at break were increased for the PPC/ESO blends,suggesting that the enhancement of the strength and toughness of PPC was achieved by the incorporation of ESO.The rheological measurement revealed that the complex viscosity,storage modulus and loss modulus of PPC were increased with the increasing ESO content at low frequency,which indicated that the addition of ESO enhanced the melt strength of PPC instead of plasticizing PPC.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.