MPT-AES同时测定航空润滑油中的铝、镁和铜

微波等离子体炬原子发射光谱法 (MPT- AES)测定未使用过的航空润滑油中铝、镁和铜含量。研究了微波功率、载气流量、工作气流量、氧屏蔽气流量、酸效应、共存离子等对元素发射强度的影响 ,优化了系统参数。铝、镁和铜的检出限分别为 15 .1ng/ m L、0 .2 8ng/ m L、2 .1ng/ m L,线性范围分别为 0 .0 5—80μg/ m L、0 .0 0 1— 5 0μg/ m L、0 .0 1— 12μg/ m L ,相对标准偏差均小于 3.7% ,回收率在 95 .6 %— 10 5 .3%之间。方法准确、快速、操作简便、维持费用低。     

基体改进-石墨炉原子吸收光谱法测定中药丹参中的铜和锌

以 NH4NO3 和 Se Triton X- 10 0作为铜和锌的基体改进剂 ,石墨炉原子吸收法测定丹参中铜和锌的含量。优化了实验条件 ,灰化温度分别提高到 12 0 0℃和 90 0℃ ,提高了方法的灵敏度。研究了不同测定波长对实验的影响 ,消除了基体干扰 ,提高了方法的重现性。用校准曲线法和标准加入法对试样分析结果一致 ,铜和锌的方法检出限分别为 0 .6 ng/ m L和 0 .9μg/ m L,RSD分别为 1.8%和 2 .3% ,回收率分别为 96 %和 10 1%。     

微波消解-石墨炉原子吸收法测定中药中铅、镉含量的研究

研究了各因素对样品消解效果的影响 ,优化了石墨炉原子吸收条件 ,建立了一种快速、有效的中药中铅、镉含量的检测方法 ,方法对铅、镉的检出限分别为 0 .14 5 ng/ m L、0 .0 119ng/ m L和线性范围分别为 0—2 0 ng/ m L、0— 2 ng/ m L。样品测定回收率为 96 .7%— 10 3.6 % ,结果满意。     

高效液相色谱法测定杀虫剂灭幼脲三号的含量

本文采用 Hypersil- ODS2 ( 4 .6mm× 2 50 mm,5μm)柱 ,乙腈 -水 - N,N-二甲基甲酰胺 ( 60∶ 4 0∶ 0 .1)为流动相 ,测定波长为 2 54nm,建立了测定灭幼脲三号的高效液相色谱法。该法线性范围为 2 .0— 80μg/m L,回归方程为 A=52 .4 1C+0 .1936,相关系数 r=0 .9987,精密度为 3.5% ( n=11,C=4 0μg/m L) ,检出限为 0 .0 5μg/m L。平均回收率在 96%— 10 4 %之间 ,已用于 2 5%水剂样品的测定 ,结果令人满意。     

桑色素-双氧水体系催化光度法测定痕量铜

本文基于过氧化氢能氧化桑色素并使之褪色的现象 ,建立了测定痕量铜的新方法。该法检出限为0 .0 0 6 μg/ m L,线性范围 4× 10 -9— 2 .4× 10 -8g/ g,适用于水样中痕量铜的测定     

中性红褪色光度法测定蒙药铜灰体系中产生的过氧化氢含量

在 p H=3.5的乙酸 -乙酸钠缓冲溶液中 ,用中性红褪色光度法测定了蒙药铜灰体系中产生的过氧化氢的含量。过氧化氢在 0— 5 0μg/ 2 5 m L范围内与 lg(A0 / A)值呈线性关系 ,线性回归方程为 lg(A0 / A) =2 .5× 10 -3+1.0 5× 10 -2 C双氧水 (μg/ 2 5 m L) ,r=0 .9999     

光泽精化学发光体系的研究与应用

对光泽精化学发光体系的动力学性质、荧光光谱、化学发光光谱及化学发光机理进行研究和探讨。详细研究了光泽精 - H2 O2 - Co( )流动注射化学发光体系的最佳分析条件。结果表明 ,当光泽精 (L c)为 2 .5×10 - 5mol/L、H2 O2 为 0 .5 mol/L、Na OH为 0 .4 mol/L、CTMAB为 2 .0× 10 - 5mol/L时 ,测定 Co( )的校准曲线线性范围为 0 .0 5— 2 0 0μg/m L ,检出限为 0 .0 1μg/m L。对 10μg/m L Co( )连续测定 7次 ,相对标准偏差为 1.7%。     

动力学光度法测定痕量铜(Ⅱ)及其反应机理

在氨水 -氯化铵缓冲溶液介质中 ,痕量铜对双氧水还原中性红褪色反应有很好的催化作用。据此建立了动力学光度法测定痕量铜的新方法。优化了反应条件 ,测定了一些动力学参数 ,探讨了反应机理。方法线性范围为 0— 2 .9μg/ 2 5 m L,检出限为 5 .2× 10 -10 g/ m L。用于人发和指甲中铜量的测定 ,结果满意。     

不同产地几种中药材中重金属含量测定及砷的形态分析

通过对不同产地几种中药材中砷、铅、镉、铜以及无机砷、三价砷含量的分析测定,得出样品中砷、铅、镉、铜以及无机砷、无机三价砷的测定RSD〈3%,加标回收率在91.32%—109.7%之间。11个样品的总砷含量在0.047—1.681μg/g之间,均低于2μg/g;无机砷含量为0.023—1.294μg/g;无机三价砷含量为0.019—0.918μg/g;铅含量两份样品未检出,其余样品为0.007—0.786μg/g,均低于5μg/g;镉的测定,两份样品未检出,其余样品含量为0.007—2.129μg/g,其中两份样品大于0.3μg/g;铜含量为4.441—14.07μg/g,均低于20μg/g。研究发现同种药材不同产地的重金属含量差异较大,部分产地金银花中镉含量超标严重,无机砷和三价砷含量相对较高,需引起重视。     

火焰原子吸收光谱法测定饲料中钙

建立了直接利用测定饲料中磷的样品分解液 ,采用火焰原子吸收分光光度法测定饲料中钙的分析方法。在吸收波长 4 2 2 .7nm处 ,Ca2 + 在 0— 15μg/ m L范围内符合比耳定律 ,回归方程为 A=0 .0 6 44C+0 .0 0 6 3,相关系数 r=0 .9996 ;以 3SA/ S计 ,检出限为 0 .0 5μg/ m L;RSD<3%。加标回收率在 98%— 111%之间 ,应用统计学 F检验法验证方法准确度 ,表明本法和国标法相比无显著差异。方法用于饲料中钙的测定 ,简便、快捷、准确。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.