Grafting Vinyl Monomers onto Silk Fibers: Graft Copolymerization of Vinyl Monomers onto Silk Using the Vanadyl Acetylacetonate Complex

Abstract

The graft copolymerization of methyl methacrylate (MMA) onto mulberry silk fibers was studied in aqueous solution using the acetylacetonate oxovanadium (IV) complex. The rate of grafting was investigated by varying the concentration of the monomer and the complex, the acidity of the medium, the solvent composition of the reaction medium, the surfactants, and the inhibitors. The graft yield increases with increasing concentration of the initiator up to 8.75 × 10^?5 mol/L, of the monomer up to 0.5634 mol/L, and thereafter it decreases. Among the various vinyl monomers studied, MMA was found to be most suitable for grafting. Grafting increases with increasing concentration of HCIO₄ and with increasing temperature. Inhibitors like picryl chloride and hydroquinone significantly decrease the extent of grafting. Alcoholic solvents at a solvents/water ration of 10:90 seem to constitute the most favorable medium for grafting. A suitable reaction scheme has been proposed, and the activation energy calculated from the Arrhenius plots.     

Grafting of Acrylamide On 1, 1, 2, 2-Tetra-Chloroethane Preswelled Polyethylene Terephthalate) Films Using Azobisisobutyronitrile Initiator

Abstract

Graft polymerization of acrylamide (AAm) on 1, 1, 2, 2 tetrachloro-ethane (TCE) preswelled poly(ethylene terephthalate) (PET) films were performed with chemical initiation method using asobisiso-butyronitrile (AIBN) initiator. Temperature was found to have a greater effect on the swelling then the swelling time. Variation of the graft yield with polymerization temperature, time, AIBN concentration, AAm concentration, AIBN and AAm inclusion times were investigated. The optimum temperature for grafting was found to be 70°CC. The graft yield was observed to increase with polymerization time, AAm concentration, initiator and monomer diffusion time up to a saturation graft yield and then leveled off. An increase in AIBN concentration first enhanced the percent grafting then showed a decrease. The addition of some salts (Ni²⁺, Cr³⁺, Co²⁺, Cu²⁺) on the rate of grafting was also investigated. From the temperature dependence of the initial rate of grafting, the overall activation energy was found to be 4. 1 kcal/mol and relevant rate equation have been derived. The effect of grafting on film propities, such as water absorption capacity, intrinsic viscosity were determined. Grafted films were characterized by FTIR spectros-copy and scanning electron microscopy (SEM).     

Analysis and Characterization of Microwave Irradiation–Induced Graft Copolymerization of Methyl Methacrylate onto Delignified Grewia Optiva Fiber

Grafting of methyl methacrylate (MMA) onto delignified Grewia optiva fiber using ascorbic acid/H₂O₂ as an initiator was carried out under microwave irradiation. The effects of varying the microwave power, exposure time, and concentration of initiator and monomer of graft polymerization were studied to obtain maximum grafting percentage (26.54%). The experimental results showed that the optimal conditions for grafting were: exposure time, 10min; microwave power, 110 W; ascorbic acid concentration, 3.74mol/L × 10^?2; H₂O₂ concentration, 0.97mol/L × 10^?1; monomer concentration, 1.87mol/L × 10^?1. The graft copolymers were characterized by Fourier transform-infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA).     

Grafting onto Starch. IV. Graft Copolymerization of Methyl Methacrylate by Use of AIBN as Radical Initiator

Grafting of poly(methyl methacrylate) onto starch has been investigated in aqueous medium by using AIBN as radical initiator. Starch-g-PMMA has been characterized by determination of starch in the graft copolymer. Percentage of grafting has been determined as functions of concentration of monomer, concentration of initiator, reaction time, and temperature. From scanning electron microscopic studies, evidence for grafting of PMMA onto starch has been presented.     

Graft Copolymerization of Methyl Methacrylate onto Poly(Ethylene Terephthalate) Fibers Using Benzoyl Peroxide

Abstract

The graft copolymerization of methyl methacrylate onto poly(ethylene terephthalate) fibers has been studied using benzoyl peroxide as initiator. The grafting reactions were carried out within the 70 to 90°C temperature range, and the variations of graft yield with monomer and initiator concentrations were also investigated. The overall activation energy for grafting was calculated as 34.1 kcal/mol. The results of dyeability with the disperse dye suggested that diffusion into the fiber structure was moderately difficult when the graft yield reached 14?15%. The maximum graft yield was obtained at a benzoyl peroxide concentration of 4.00 × 10^?3 M. The decomposition temperature values obtained from thermogravimetric analysis show that the thermal stability of poly(ethylene terephthalate) fibers decreased as a result of grafting. Further, such change in the properties of methyl methacrylate grafted fibers as density, diameter, and moisture regain were also determined.     

Graft Copolymerization of 2‐Acrylamido‐2‐methyl Propane Sulfonic Acid on Dimethyl Sulfoxide Pretreated Poly(Ethylene Terephthalate) Films Using Cerium Ammonium Nitrate as Initiator

Abstract

In this study, graft polymerization of 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS) on poly(ethylene terephthalate) (PET) films using cerium ammonium nitrate (CeAN) as an initiator was investigated. Before the polymerization reaction was carried out, films were swelled in dimethyl sulfoxide (DMSO) at 140°C for 1 h. The effect of polymerization temperature, time, initiator, and monomer concentrations on the graft yield were investigated. It was observed that the graft yield was initially increased with increasing temperature, monomer, and initiator concentrations; and then decreased. Graft yield was found to increase with increasing polymerization time up to 5 h, then remain constant. The effects of monomer and initiator inclusions on the grafting yield were also examined. Optimum conditions for grafting were found to be [AMPS] = 1.0 M, [Ce⁴⁺] = 1.5 × 10^?2 M, T = 85°C and t = 5 h. The rate of grafting was found to be proportional to the 0.1 and 0.4 powers of monomer and initiator concentrations, respectively. The overall activation energy for the grafting was calculated to be 11.4 kcal mol^?1. The effect of grafting on PET film properties such as intrinsic viscosity and water absorption capacity were determined. The grafted PET films were characterized with FTIR spectroscopy and scanning electron microscopy (SEM).     

Surface modification of coir fibers I: studies on graft copolymerization of methyl methacrylate on to chemically modified coir fibers

Graft copolymerization of methyl methacrylate (MMA) onto chemically modified coir fiber was studied using a CuSO₄–KIO₄ combination as initiator in an aqueous medium in the temperature range of 50–70 °C. Concentrations or [IO₄−] = 0.005 mol/l and [Cu2+] = 0.002 mol/l produce optimum grafting. The effects of time, temperature, amount of coir fiber, some inorganic salts and organic solvents on graft yield have also been investigated. On the basis of experimental findings, a reaction mechanism has been proposed. Evidence of grafting was studied from fourier transform infrared spectroscopy and scanning electron microscopy of chemically modified coir and MMA‐grafted coir. Tensile properties such as maximum stress at break, extension at break and Young's modulus of untreated, defatted, chemically treated and grafted coir fibers were evaluated and compared. Grafted coir fiber showed an increase in tensile properties such as maximum stress at break, extension at break and Young's modulus. Copyright © 1999 John Wiley & Sons, Ltd.     

Ascorbic Acid/Hydrogen Peroxide–Initiated Graft Copolymerization of MMA onto Bombyx mori Silk Fibroin

Graft copolymerization of methyl methacrylate (MMA) onto Bombyx mori silk fibroin was investigated using ascorbic acid and hydrogen peroxide as redox system. The effect of different reaction parameters such as reaction time, temperature, and initiator and monomer concentrations on graft yield were determined. The optimum grafting conditions were found to be temperature = 65°C, time = 120 min, monomer concentration = 2.82 × 10^?1 mol/L, ascorbic acid concentration = 2.83 × 10^?2 mol/L, and H₂O₂ concentration = 1.58 × 10^?1 mol/L. The structural properties of the fibers were studied with the help of FT-IR, scanning electron microscopy (SEM), X-ray diffraction, and TGA techniques.     

Graft Copolymerization of Acrylamide on Swollen poly (Ethylene Terephthalate) Fibers Using Cerium Ammonium Nitrate Initiator

Abstract

In this study the graft copolymerization of acrylamide (AAm) on swollen poly(ethylene terephthalate) (PET) fibers using cerium ammonium nitrate (CeAN) initiator was investigated. Five organic solvents, dimethylsulfoxide (DMSO), morpholine, acetic acid (HAc), n-butanol, and 1,2-dichloroethane (DCE), were used as swelling agents. DMSO was found to be the most suitable swelling agent. Solvent diffusion into the fibers was observed to increase with treatment time and temperature. The optimum graft yield was obtained when fibers were grafted after having been swollen in DMSO for a period of 1 hour at 140°C. Variation of graft yield with polymerization time and temperature, and monomer, initiator, and acid concentrations were investigated. Graft yields were observed to increase initially with polymerization time, then to level off, and were found to increase up to a certain monomer and Ce⁴⁺ concentration, then to decrease slightly. The effect of grafting on such fiber properties as diameter, viscosity, and moisture gain were also investigated.     

Grafting of polyacrylonitrile to granular corn starch

Acrylonitrile grafts readily to granular corn starch in aqueous slurry when initiated by hydrogen peroxide plus activator. Prime evidence for grafting lies in the ease of separating PAN from starch in high yield when the initiator is azobisisobutyronitrile rather than peroxide. Grafting efficiencies are determined by extraction with appropriate solvents: dimethylformamide for homo-PAN, and boiling water for ungrafted starch. Grafting efficiencies of PAN range from 78 to 95%, M?_n values for grafted PAN are 4,000 to 90,000, and frequency of attachment of side chains range from 300 to 1100 glucose units per chain. Increasing the monomer level, at fixed initiator concentration, tends to result in longer rather than more frequent side chains. AN behaves much as has been previously found for MMA, but the somewhat more efficient grafting at more frequent intervals and the more nearly uniform distribution of polymer in the starch granule suggest that AN penetrates the starch granule more readily than MMA.     

芴酮引发光接枝改性LDPE膜的研究

采用紫外光引发接枝表面改性的方法,以芴酮(FL)为引发剂,在低密度聚乙烯(LDPE)薄膜表面上接枝丙烯酸(AA)、甲基丙烯酸(MAA)、丙烯酸甲酯(MA)、甲基丙烯酸甲酯(MMA)、丙烯酰胺(AM)等单体,以赋予薄膜表面新的化学性质.考察了引发剂浓度、紫外光的辐照时间、辐照强度、单体种类对LDPE薄膜接枝程度的影响.结果表明,在一定范围内,增加芴酮浓度,可以提高单体的接枝率,但当芴酮浓度达到5%时,接枝率反而下降.延长辐照时间至4 min和提高紫外光的辐照强度达100 W/m2,均有利于接枝反应的进行.不同单体在LDPE膜上的接枝能力与单体的活性、单体与基材的相容性等因素有关.接枝后,LDPE与水的接触角下降程度不仅与单体在膜上的接枝量有关,还与接枝单体的亲水性能密切相关.     

Graft copolymerization of itaconic acid-methacrylamide comonomers onto poly(ethylene terephthalate) fibers

The graft copolymerization of itaconic acid-methacrylamide (IA-MAAm) comonomers was carried out using benzoyl peroxide as initiator onto poly(ethylene terephthalate) (PET) fibers in an aqueous medium. The grafted fibers were characterized by FTIR, TGA, DSC and SEM analysis. Effect of various parameters on graft yield such as feed composition, feed and initiator concentration, reaction time and temperature were investigated. The graft yield in the presence of MAAm increased because of the synergistic effect of MAAm comonomer. While, the graft yield alone with the IA onto PET fiber was 2.2%, the use of MAAm as a comonomer increased the amount of IA introduced to the PET fiber up to 13.7%. The reactivity ratios for both monomers were determined by using a Fineman-Ross plot. The grafting rate and saturation graft yield was increased upon increasing the temperature between 65 °C and 85 °C. When the temperature increased further than 85 °C, the saturation graft yield decreased. The graft yield has shown an increase up to an initiator concentration of 1.0 × 10⁻² M and slightly decreased. The grafting increased the dyeability with acidic and basic dyes, and moisture absorption capacity but decreased the thermal stability of the fibers.     

Effect of initiators on grafting in the initial stage of the emulsion polymerization of methyl methacrylate using poly(vinyl alcohol) as a protective colloid

 To make clear the reason of unsuitability of poly(vinyl alcohol) (PVA) protective colloid for the emulsion polymerization of conjugated monomers, a model experiment of emulsion polymerization of methyl methacrylate (MMA) was carried out with ammonium persulfate (APS) or azobis(isobutyronitrile) (AIBN) initiators, where a small amount of MMA (1/100th of the concentration compared with ordinary emulsion polymerization) was employed. This corresponds to the initial stage of the emulsion polymerization. Grafting of MMA onto PVA took place remarkably irrespective of the kind of the initiators. Formation of homo-poly(MMA) was observed to a small extent. The formation of new emulsion particles smaller than 100 nm continued to increase to almost the end of the polymerization. PVA molecules in the grafted polymer are supposed to act as stabilizers of newly formed particles. From kinetic treatment using the experimental data, the important issues were derived as follows. Firstly, the sulfate anion radical from APS is much more reactive than the isobutyronitrile radical from AIBN in terms of hydrogen abstraction from PVA. Secondly, high grafting ability of the latter initiator system, notwithstanding the much lower reactivity in the hydrogen abstraction compared with the APS system, is attributed to the relative reactivity of the primary radicals, i.e., hydrogen abstraction reaction from PVA to initiation reaction with MMA. The much slower rate of addition of the isobutyronitrile radical to the monomer compared with that of hydrogen abstraction from PVA facilitates the grafting, although the rate constant of hydrogen abstraction is far smaller than that with the sulfate anion radical by 10⁻⁴ times. Received: 26 April 2001 Accepted: 6 September 2001     

Grafting Vinyl Monomers onto Silk Fibers. XIII. Graft Copolymerization of Methyl Methacrylate onto Silk Using Fe3+−Cysteine Redox System

The graft copolymerization of methyl methacrylate onto silk fibers initiated by the ferric chloride-eysteine redox system has been investigated in aqueous medium. The rate of grafting was calculated by varying the concentrations of monomer, initiator, acidity of the medium, cysteine, and temperature. The percentage of grafting increases with an increase of Fe³⁺ concentration up to 2,5 × 10^?3 mol/L and thereafter it decreases. The graft yield increases steadily upon increasing the monomer concentration. The graft yield also increases with increasing cysteine concentration up to 0.5 × 10^?3 mol/L and then decreases. The effect of the perchloric acid concentration, temperature, solvents, and certain neutral salts on graft yield has also been investigated and a suitable reaction scheme has been proposed.     

Ascorbic Acid/H2O2-initiated Graft Copolymerization of Methyl Methacrylate onto Abelmoschus Esculentus Fiber: A Kinetic Approach

Graft copolymerization of methyl methacrylate onto lignocellulosic Abelmoschus esculentus fibers was successfully carried out in aqueous medium using ascorbic acid and hydrogen peroxide as redox initiator. Maximum percentage of grafting was achieved when the concentrations of ascorbic acid, hydrogen peroxide, and monomer were 3.85 × 10^?2, 2.41 × 10^?1, and 1.87 × 10^?1 mol/L respectively at a temperature of 45°C for a reaction time of 90 min. The kinetics of graft copolymerization was also studied, and it was found that the rate expression for graft copolymerization is (R_g) = K [Asc]^0.68[H₂O₂]^0.49[MMA]^1.17. The activation energy for graft copolymerization of MMA onto Abelmoschus fiber was found to be 12.48 KJ/mol. The graft copolymers thus formed were characterized by FT-IR spectroscopy, scanning electron microscopy and thermogravimetric analysis.     

Solvent “Goodness” in Polymer Separation by Flow

The graft copolymerization of methyl methacrylate onto silk fibers was investigated in aqueous solution using the V⁵⁺?thiourea redox system. The rate of grafting was determined by varying monomer, thiourea, acidity of the medium, temperature, initiator concentration, and reaction medium. The percentage of graft yield increases significantly by increasing the initiator concentration up to 0.01 M and thereafter decreases with a further increase of initiator concentration. The graft yield increases with an increase of thiourea concentration up to 10.0 × 10^?4 and then decreases with a further increase of thiourea concentration. The effect of increasing the monomer concentration brings about a significant enhancement in the graft yield. A suitable kinetic scheme has been proposed and the rate equation has been evaluated.     

Preparation of Poly(ethylene terephthalate)‐g‐Methacrylamide Copolymers Initiated by Azobisizobutyronitrile: Characterization and Investigation of Some Properties

Poly(ethylene terephthalate)‐g‐methacrylamide (PET‐g‐MAAm) copolymer was prepared by graft copolymerization in organic solvent/water mixtures by using azobisizobutyronitrile (AIBN) as an initiator. The highest graft yield was obtained in 20/80 (v/v) acetonitrile/water mixture as 30.0%. The effect of polymerization parameters such as the ratio of solvent/water mixture, concentrations of initiator and monomer, temperature and time on the graft yield was studied. The moisture regain of the PET fiber increased with grafting from 0.42% to 3.01%. Thermogravimetric data showed that the thermal stability of PET fibers decreased with grafting and 85% of total weight of 29.7% grafted fiber was lost at 500°C. On the other hand, fiber density decreased with increasing graft yield. At SEM micrographs, the layers oriented in the direction of fiber length were observed on the surface of PET fiber as a result of grafting.     

Grafting of polymers onto a carbon‐fiber surface by ligand‐exchange reaction of poly(vinyl ferrocene‐co‐vinyl monomer) with polycondensed aromatic rings of the surface

To improve the surface of carbon fiber, the grafting reaction of copolymer containing vinyl ferrocene (VFE) onto a carbon‐fiber surface by a ligand‐exchange reaction between ferrocene moieties of the copolymer and polycondensed aromatic rings of carbon fiber was investigated. The copolymer containing VFE was prepared by the radical copolymerization of VFE with vinyl monomers, such as methyl methacrylate (MMA) and styrene, using 2,2′‐azobisisobutyronitrile as an initiator. By heating the carbon fiber with poly(VFE‐co‐MMA) (number‐average molecular weight: 2.1 × 10⁴) in the presence of aluminum chloride and aluminum powder, the copolymer was grafted onto the surface. The percentage of grafting reached 46.1%. On the contrary, in the absence of aluminum chloride, no grafting of the copolymer was observed. Therefore, it is considered that the copolymer was grafted onto the carbon‐fiber surface by a ligand‐exchange reaction between ferrocene moieties of the copolymer and polycondensed aromatic rings of carbon fiber. The molar number of grafted polymer chain on the carbon‐fiber surface decreased with increasing molecular weight of poly(VFE‐co‐MMA) because the steric hindrance of grafted copolymer on the carbon‐fiber surface increases with increasing molecular weight of poly(VFE‐co‐MMA). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1868–1875, 2002     

Free radical grafting of monomers to polydienes. IV. Kinetics and mechanism of methyl methacrylate grafting to polybutadiene

The radical grafting of methyl methacrylate (MMA) onto polybutadiene (PBD) in benzene solution at 60°C is more efficiently induced by benzoyl peroxide (BP) than by azoisobutyronitrile (AIBN). PBD exerts a pronounced retardation on the polymerization of MMA and the grafting efficiency is governed by the ratio of rubber to monomer in the system. With BP as initiator, a fairly simple kinetic expression, relating grafting efficiency with reactant concentrations, can be derived by making certain approximations, including the neglect of termination grafting. The experimental data are reasonably consistent with this equation and yield acceptable values of several kinetic parameters. With AIBN, termination grafting is more significant. In consequence the relevant kinetic equation can be only qualitatively validated.     

Stoichiometric formation of methyl methacrylate oligomer by triethylaluminum in the presence of azobisisobutyronitrile

The yield of methyl methacrylate (MMA) polymerization as a function of triethylaluminum (TEA) concentration for a constant azobisisobutyronitrile (AIBN) concentration at 50°C has been measured. The polymerization yield does not differ markedly from that with AIBN alone as long as the initial TEA concentration is held smaller than four times the initial AIBN concentration. A sudden decrease in yield and molecular weight is observed at TEA/AIBN concentration ratios between 4 and 5. A plot of M?_w^?1 vs. TEA gives a rate-transfer constant of 89 1./mole-sec. If the reaction mixture is vacuum-evaporated with a previous addition of water, instead of precipitating the polymer, the formation of a considerable amount of MMA oligomer is detected for TEA/AIBN concentration ratios larger than 4. On the average, each TEA molecule in excess of four times the initial amount of AIBN yields one oligomer molecule. The data are consistent with a radical polymerization mechanism for the high molecular weight polymer and with a nonradical one for the oligomer formation.