悬浮态乳液聚合

对一种新的聚合方法－－悬浮态乳液聚合的研究进展进行了综述。通过对比悬浮聚合，乳液聚合和悬浮态乳液聚合方法的异同，突出了悬浮态乳液聚合的优点。讨论了悬浮态微液聚合的机理，以及分散剂，表面活性剂，水油比等对聚合物颗粒形态的影响。     

核壳乳液聚合法制备含氟硅丙烯酸酯乳液

以氟醇RfCH2CH2OH和乙烯基硅氧烷VTES为原料合成的氟硅单体,与甲基丙烯酸甲酯、丙烯酸丁酯在复合乳化体系中通过核壳乳液聚合制备了稳定的氟硅共聚乳液。对氟硅单体和氟硅丙烯酸酯共聚物的结构用红外光谱进行了表征,结果表明,得到了目标单体和共聚物。共聚物的TEM形态观察发现,乳胶粒子具有明显的核壳结构,平均粒径在125 nm左右。与丙烯酸酯共聚物相比,氟硅丙烯酸酯共聚物乳胶膜的吸水率降低至8.32%,热分解温度提高了23℃,耐溶剂性与氟硅单体的含量关系不大。     

Reactive Surfactant in the Emulsion Copolymerization of Methyl Methacrylate and Octyl Acrylate

The emulsion copolymerization of methyl methacrylate and octyl acrylate was studied using a reactive surfactant ammonium sulfate allyloxy nonylphenoxy poly(ethyleneoxy) (10) ether (DNS‐86), and a conventional surfactant sodium dodecylbenzene sulfonate (DBS) with a similar structure as a comparison sample. A series of latex samples have been prepared with two kinds of surfactants, and their properties have been characterized and compared. ¹H‐NMR proves that the reactive surfactant has been incorporated into the resulting copolymers. The atomic force microscopy (AFM) proves that the reactive surfactant DNS‐86 migrate to the surface of the latex film to a much less degree than the conventional surfactant DBS. Transmission electron microscopy (TEM) demonstrates that there are some differences in the particle morphologies. The stability and water‐resistance of the latex films prepared by reactive surfactant DNS‐86 are better than those prepared by the conventional surfactant DBS.     

Stability of Emulsion Polymerization of New Fluorinated Acrylate Emulsion and Its Characterization

The new fluorinated acrylate emulsion was synthesized by using the intermediate perfluorous nonene and 2-hydroxyethyl methacrylate as the staring reactants via semi-continuous seeded emulsion polymerization. The structures, glass transition temperature, thermal property and water repellency of the fluorinated acrylate emulsion were characterized with FTIR, differential scanning calorimetry, thermal analysis, and contact angle meter. Influences of many factors such as the theoretical solid content, the temperature of the emulsion polymerization on the stability of the emulsion polymerization, the added amount of emulsifiers and the added amount of the initiator were studied. Results show that the stability of the emulsion polymerization is fairly good when the theoretical solid content is below 30% and the reaction temperature is 80°C and the added amount of emulsifiers and the initiator are 6.0–8.0% and 2.0% respectively. In comparison with the acylate emulsion, the thermal stability of the fluorinated acrylate emulsion is decreased but the water repellency of the fluorinated acrylate emulsion is greatly increased.     

反相乳液聚合法制备丙烯酰胺-丙烯酸铵共聚物

以煤油为连续相,水为分散相,Span-80/Tween-80为复配乳化剂,过硫酸铵为引发剂,丙烯酰胺、丙烯酸和氨水为原料,采用反相乳液聚合法合成了丙烯酰胺-丙烯酸铵共聚物絮凝剂.考察了乳化剂种类及用量、引发剂浓度、单体浓度、EDTA用量、聚合温度等对共聚物特性黏数的影响.确定了最佳实验条件,利用FTIR对样品进行了表征.     

非离子型可聚合聚氨酯/苯乙烯的超浓乳液聚合

研究了以非离子型可聚合聚氨酯(PUAG)和苯乙烯(St)为混合单体的超浓乳液聚合, 并且考察了n(NCO)/n(OH)摩尔比、复合乳化剂体系质量浓度[E]、不同乳化剂的种类、引发剂质量浓度[I]、单体体积分数(或分散相体积分数, 也称内相比Φ)、聚合温度等因素对聚合稳定性、动力学的影响. 同时结合光相关光谱(PCS)测定了聚合物乳胶粒子大小和粒径分布, 用透射电子显微镜(TEM)观察了粒子形态, 结果表明: 当n(NCO)/n(OH)＝2∶1, T＝328 K, Φ＝80.39%, [I]＝0.8% g/g (PUAG-St), [E]＝0.22 g/mL H₂O, m(MS-1)/m(CA)＝2∶1, PVA＝0.01 g/mL H₂O时, 超浓乳液不仅有较好的聚合稳定性和较快的聚合速率, 而且粒径小分布均匀. 同时, 在此条件下的表观动力学表达式和表观活化能分别确定为R_p＝k[I]^0.50[E]^0.73[M]^0.54和 E_a＝29.7 kJ/mol. 热失重分析(TGA)进一步表明: 调节PUAG的含量可以达到对聚苯乙烯的改性, 提高聚苯乙烯的热稳定性.     

Maximum Achievable Particle Size in Emulsion Polymerization: Modeling of Large Particle Sizes

A simplified model for particle formation in emulsion polymerization (comprising aqueous‐phase propagation to degrees of polymerization which may enter a pre‐existing particle and/or form new particles by homogeneous or micellar nucleation, coupled with the aqueous‐phase and intra‐particle kinetics of oligomeric radicals) is formulated to provide a model suitable for the simulation of systems containing large‐sized particles. The model is particularly useful to explore conditions for growth of large particles while avoiding secondary particle formation. Applied to the Interval II emulsion polymerization of styrene with persulfate initiator at 50°C, it is found that there is an effective maximum particle size that can be achieved if the formation of new particles is to be avoided. The parameter space of initiator concentration, particle number concentration and particle radius is mapped to show a “catastrophe” surface at the onset of new nucleation. Advanced visualization techniques are used to interpret the large number of simulations in the series, showing a maximum achievable particle diameter of around 5 μm.     

氯丁胶乳乳液接枝甲基丙烯酸甲酯的反应动力学

采用乳液聚合法将甲基丙烯酸甲酯(MMA)接枝到氯丁胶乳上,红外光谱和核磁共振氢谱证实了接枝产物的生成。 研究了反应温度、乳化剂浓度、引发剂浓度和单体浓度对表观聚合速率的影响。 结果表明,当反应温度为50 ℃,引发剂叔丁基过氧化氢 四乙烯五胺（t-BHP/TEPA）用量为氯丁胶乳干重的0.5%,单体/聚合物质量比m(M)∶m(P)=3∶5,乳化剂十二烷基连苯醚二磺酸钠（DSB）用量为单体总质量1%时,单体转化率和接枝效率分别为99.1%和54.9%。 聚合反应动力学关系式为：Rp=Kc(E)0.15c(I)0.30c(MMA)1.41,式中,K为常数,在40~55 ℃范围内,聚合反应的表观活化能Ea＝60.2 kJ/mol。 接枝聚合基本符合自由基反应机理。     

Styrene Emulsion Polymerization above the CMC: New Evidence on Particle Nucleation by means of AFFFF

Summary: The number (N) and size distribution of particles (PSD) of a styrene emulsion polymerization above the CMC were studied by means of asymmetric flow‐field flow fractionation (AF⁴). Bimodal PSDs were obtained, suggesting that coagulation of the primary particles is not as extensive as would be expected, according to the coagulative mechanism. AF⁴ allowed it to be demonstrated that N is constant during interval II, and that the resolution limit of other particle sizing techniques can lead to erroneous mechanistic inferences, from the evolution of N.

Particle size distribution measured at low conversion for the emulsion polymerization of styrene, obtained by AF⁴ and DLS. The initial surfactant (S₀), initiator (I₀) and monomer (M₀) concentrations are indicated in the figure.     

The Effect of Nano-SiO2 Colloid on Soap-free Emulsion Polymerization of Methyl Methacrylate and Hydroxyethyl Methacrylate

Soap-free emulsion polymerization of methyl methacrylate (MMA) and hydroxyethyl methacrylate (HEMA) was carried out in the presence of colloidal nano-SiO₂ particles. The effect of nano-SiO₂ level on the monomer conversion, polymerization rate (Rp), and emulsion stability was investigated. The viscosity, particle size distribution of the emulsions, surface tension, and ionic conductivity of these systems were determined. Upon the introduction of the nano-SiO₂ particles into this system, the Rp and monomer conversion increased and the average particle size of the P(MMA-HEMA) emulsion decreased in comparison to emulsions formed in the absence of nano-SiO₂. However, the particle size distribution became broader to some degree. Scanning electron microscope observations demonstrated that the shape of these latex particles were uniformly spherical. The surface tension and ionic conductivity of the system increased significantly after polymerization, but the presence of nano-SiO₂ resulted in an increase in surface tension and a decrease in ionic conductivity in comparison to the particle–free system.     

Particle Nucleation and Growth in the Emulsion Polymerization of Styrene: Effect of Monomer/Water Ratio and Electrolyte Concentration

This work is an extension of previous research results reported by our team (Colloid and Polymer Science 2013, 291: 2385-2398), where large scale and high solid content latexes of poly(n-butyl acrylate) were obtained with the particle coagulation method induced by the electrolyte. However, how to prepare controlled particle size distribution polymer latex has not been studied. Thus, in this study, the effect of the monomer/water ratios and electrolyte concentrations on particle formation and growth methods were studied by following the tracks of the evolutions of particle size, number and distribution as a function of reaction time or conversion. Experimental results showed that the length of time that particle nucleation occurred increased with increasing monomer charged for the systems without electrolyte. A point worthy of attention here is that homogeneous nucleation may occur at high monomer concentrations (30/70, 40/60). However, electrolyte added could be made the nucleation mechanism shift from micellar/homogeneous nucleation to micelle /coagulation nucleation. As a result, the final particle size distribution can be controlled by adding an appropriate electrolyte to regulate the nucleation mechanism. Spherical and uniformly sized particles could be obtained when electrolyte concentration is between 0.2 wt% and 0.4 wt% for water at the high monomer/water ratio (40/60). The effects of electrolyte concentration on nucleation mechanism mainly were expressed by decreasing the solubility of the monomer and interparticle potential, and then preventing homogeneous nucleation and enhancing particle coagulation.     

聚硅氧烷/甲基丙烯酸甲酯核壳结构复合粒子的制备

聚硅氧烷/甲基丙烯酸甲酯核壳结构复合粒子的制备;种子乳液聚合;核壳结构     

Effect of Microwave Activation on Polymerization Rate and Molecular Weight Development in Emulsion Polymerization of Methyl Methacrylate

Polymerization rate and molecular weight development experimental results for the emulsion polymerization of methyl methacrylate (MMA), in the presence of potassium persulphate (PPS) as initiator, and activated with a 50 W microwave source, are reported. The polymerization kinetics of the microwave activation experiment (MA) was compared against a traditional conductive heating (CH) polymerization reaction. The number average molecular weights, M_n, of the polymer samples obtained with microwave activation were significantly higher than those obtained from conductive heating. These high values of M_n were obtained from the beginning of the polymerization reaction. Polydispersity index (PDI) values in the range of 1.18 to 1.83 were obtained in the microwave irradiated samples. These values are lower than those produced by conventional emulsion polymerization of styrene and other vinyl monomers, and resemble the PDI values obtained in controlled‐radical polymerization processes. Polymer particles of submicron size (60 to 100 nm) were obtained.     

室温下甲基丙烯酸甲酯原子转移自由基乳液聚合反应研究

以卤化亚铜（CuX）/1,10-邻二氮菲（phen）配合物为催化剂、2-溴代异丁酸 乙酯（EBiB）为引发剂、十二烷基磺酸钠（SLS）为乳化剂,进行了甲基丙烯酸甲 酯（MMA）的原子转移自由基乳液聚合（ATRP）反应。结果表明,与较高温度（70 - 90 ℃）下的聚合反应相比,室温（25 ℃）时聚合反应有更好的可控性,通过 外加钝化剂的复合催化引发体系CuBr/CuBr_2/phen/EBiB或利用CuCl/phen/EBiB催 化引发体系的“卤素交换反应”,可进一步改善聚合反应的可控性。紫外发光谱测 定结果表明,CuBr/phen配合物在MMA相中的分配倾向随着温度的降低而增大,使得 室温下MMA的乳液ATRP保持了较好的可控性和较快的反应速度。     

Polymerization of Blending Cholesteryl Acrylate and Methyl Phenyl Benzoyl Acrylate

Liquid crystal is a material which is between solid and liquid phase and commonly called mesophase. Blends of liquid crystal are of great interest because of their unique optical properties. Blending in this study using two monomers of liquid crystal were cholesteryl acrylate and methyl phenyl benzoyl acrylate. The polymerization process using uv curing techniques by irradiation UV ray and without irradiation UV ray. Polymerization of blending liquid crystal acrylate using initiator 2-hydroxy-2-methyl-1-phenylpropane. Based on peak at GPC curve of polymerization by irradiation UV ray, type of that polymer is copolymer. Therefore the polymerization without UV ray, type of that polymer is homopolymer. SEM images of liquid crystal acrylate polymer showed lamella chain models that are characteristic of a polymer chains. Type of polymer liquid crystal acrylate was the type of Side Chain Liquid Crystalline Polymers (SCLCPs). Therefore acrylate polymer liquid crystal in this research has semi-crystalline phase, which contained crystalline phase and amorphous phase on the XRD pattern. The results of FT-IR spectroscopic characterization of the two monomers showed a peak at the wave number of 1600.43 cm ^-1 and 1622.86 cm^-1 which indicates a double bond (C=C) were obtained from acrylation. While the spectroscopy on the product blending the wave number of the peak regions is reduced that shows that carbon double bonds (C=C) in the acrylate group has polymerized. It also strengthened with a very sharp peak for CC functional groups on the wave number of 2855.15 cm^-1. The results of this study indicate that the liquid crystal polymer acrylic polymerization results with radiation UV ray and without UV ray, respectively absorb light in the UV wavelength region 363 nm and 351 nm.     

A Comparative Study of Methyl Methacrylate/Butyl Acrylate Copolymerization Kinetics by Atom‐Transfer and Conventional Radical Polymerization

Methyl methacrylate and butyl acrylate monomers are copolymerized by atom‐transfer radical polymerization, affording polymers with well‐controlled molecular weight and low polydispersity. A kinetic analysis of this system is compared with the corresponding free‐radical polymerization system. The copolymerization rate follows an opposite trend to that observed in conventional copolymerization. This fact is attributed to a smaller population of radicals generated in the reaction, since the relative fraction of propagating radicals is the same as that in classical copolymerization.     

Molecular Watchmaking: ab initio Emulsion Polymerization by RAFT-controlled Self-assembly

Controlled radical polymerization using RAFT has the potential to make polymers with virtually any desired molecular architecture. For this to be implemented on an industrial scale, it must be performed by polymerization in disperse media. However, simply adding a RAFT agent to a conventional emulsion polymerization recipe leads to a loss of molecular weight control and formation of coagulum, probably because of nucleation in droplets, which is normally an unlikely phenomenon in emulsion polymerizations. Recently, a method has been devised for implementing RAFT in ab initio emulsion polymerization that avoids droplets in the particle formation stage. The molecular weight distribution of the polymer thus formed shows that molecular weight control is maintained throughout the polymerization. A model is developed to predict the particle size formed in this new type of emulsion polymerization. The new methodology enables synthesis of novel dispersions where molecular architecture can be precisely controlled, such as structured core-shell particles.     

离子型共聚单体参与下的全氟丙烯酸酯无皂乳液共聚

离子型共聚单体参与下的全氟丙烯酸酯无皂乳液共聚;全氟烷基丙烯酸酯;无皂乳液;离子型共聚单体     

聚合工艺及m(MMA)/m(EA)对MMA-Ea-AA三元无皂乳液聚合及乳胶粒性质的影响

聚合工艺及m(MMA)/m(EA)对MMA-Ea-AA三元无皂乳液聚合及乳胶粒性质的影响;甲基丙烯酸甲酯;丙烯酸乙酯     

丙烯酸甲酯在炭黑表面的接枝聚合及水解

在炭黑表面接枝聚合物 ,可提高其在相应介质中的分散性[1] .乙酰丙酮合锰可以有效地引发羊毛、纤维素、淀粉等天然高分子的接枝聚合 [2～ 4 ] ,季君晖 [5]将其与羟甲基化炭黑组成引发体系 ,引发了甲基丙烯酸甲酯、丙烯酸丁酯、苯乙烯等单体在炭黑表面进行接枝聚合 .但该体系难以引发水溶性的单体 ,因此得到的接枝炭黑只能用于油性体系 .目前制备亲水性接枝炭黑大多采用 Ce4 +/羟甲基化炭黑引发体系 ,该体系对 O2 特别敏感 ,反应条件相当苛刻 .本文采用乙酰丙酮合锰与羟甲基化炭黑组成引发体系 ,引发丙烯酸甲酯在炭黑表面的接枝聚合 .在 Na…