聚丙烯酸(钾)/凹凸棒吸水剂的制备及性能研究

在凹凸棒存在的情况下,以丙烯酸为单体,以N,N-亚甲基双丙烯酰胺(MBA)为交联剂,过硫酸钾(KPS)为引发剂,采用水溶液聚合法合成了聚丙烯酸(钾)／凹凸棒吸水剂。用TGA和SEM对产物进行了表征。IR分析证实了凹凸棒与丙烯酸发生了接枝共聚反应。研究了引发剂的用量、交联剂的用量和粘土的用量等反应条件对复合吸水剂吸水性的影响。当凹凸棒w=0．10时,复合吸水材料在蒸馏水和生理盐水中的吸水倍数分别大于1200和100。     

基于聚乳酸的可降解形状记忆高分子的研究进展

综述了基于聚乳酸的可生物降解的形状记忆高分子材料的研究情况。首先介绍了形状记忆高分子材料的记忆效应、记忆机理,然后讨论了基于聚乳酸的三种类型的形状记忆高分子材料：单组份的聚乳酸类、聚乳酸共聚物类以及聚乳酸与无机物的复合材料,分别介绍了各种类型的形状记忆高分子材料的形状记忆性能和生物降解性能。最后,讨论了聚乳酸类记忆材料的应用情况,并对其研究前景和发展趋势进行了展望。     

聚(3,4-乙撑二氧噻吩)/木质素磺酸导电复合物的结构与性能

3,4-乙撑二氧噻吩(EDOT)以木质素磺酸(LS)作载体,通过化学氧化法聚合形成了聚(3,4-乙撑二氧噻吩)/木质素磺酸(PEDOT/LS)导电复合物.该导电复合物的结构与性能分别采用紫外可见分光光度计、红外光谱仪、zeta电位及粒度分析仪、原子力显微镜、X-射线光电子能谱仪、X-射线衍射仪、四探针测试仪、电泳仪,以及表面电阻仪来表征.结果表明,EDOT能在LS水溶液中氧化聚合,得到水分散性PEDOT/LS导电颗粒.该颗粒是一种聚电解质复合物,等量电荷配比的PEDOT/LS位于内核而富余的亲水性LS包在外层.LS与PEDOT两者之间存在较强的作用力,无法通过电泳分开.X-射线衍射仪结果表明该复合物是无定型的.当LS与EDOT单体质量比从0.7∶1升高至3.0∶1时,复合物的粒径从673 nm降低至348 nm,涂膜表面变得均匀,同时表面电阻从1.9 kΩ/sq上升至87.2 kΩ/sq.用PEDOT/LS配置得到的抗静电剂,可以使玻璃片表面电阻从1012Ω/sq减小至107Ω/sq.     

辉光放电电解等离子体引发合成聚丙烯酸钠/腐植酸复合高吸水性树脂

以丙烯酸和腐植酸为原料,N,N-亚甲基双丙烯酰胺为交联剂,在水溶液中采用辉光放电电解等离子体引发聚合反应制备聚丙烯酸钠/腐植酸复合高吸水性树脂。 考察了放电电压、交联剂、丙烯酸中和度、后聚合温度、腐植酸钠和丙烯酸的含量对树脂吸水率的影响,讨论了树脂在0.9%氯化钠溶液中的溶胀速率和不同pH值溶液中的溶胀行为。 用红外光谱和热重分析分别对产物进行了结构表征和稳定性测试,结果表明,最佳的合成条件为：放电电压470 V、交联剂质量分数为0.6%、腐植酸钠质量分数为4%、丙烯酸质量分数为10%、中和度60%、后聚合温度70 ℃。 所得复合树脂对蒸馏水的吸水率为1152 g/g,对0.9%NaCl溶液的吸水率为89 g/g,800 ℃后复合树脂残留率为44.3%。     

胆固醇修饰的低分子量聚乙烯亚胺接枝化聚[L-天冬酰胺-co-L-赖氨酸]作为基因载体的性能研究

通过将低分子量的聚乙烯亚胺(PEI600)及其胆固醇衍生物与聚(L-天冬酰胺-co-L-赖氨酸)(PSL)进行开环反应, 合成了一类新型的肿瘤靶向基因载体, 研究了这类载体与DNA形成复合物的性质以及介导绿色荧光蛋白质粒pEGFP-C1转染不同细胞的性能. 结果表明, 在复合质量比大于5∶1时, 各载体均能与DNA形成结构稳定的复合物. 同时转染实验结果证明, 通过在侧链引入一定数目的胆固醇, 可以明显提高载体对于癌细胞HepG2和Hela的转染效率. 这类新型的载体具有良好的细胞相容性、较高的转染效率以及易于进行靶向修饰等特点, 在基因治疗研究领域中将具有较好的潜在应用价值.     

聚天冬氨酸的合成研究

以L-天冬氨酸为原料,磷酸为催化剂,在不同溶剂中进行缩聚反应,合成中间体聚丁二酰亚胺(PSI),当混合溶剂为m三甲苯／m环丁砜=7／3时,可得到较高分子量的PSI。当催化剂与单体的质量比为0．14时,分子量达到最大值。将PSI碱解得到聚天冬氨酸。     

基于聚乙二醇结构调控高分子量聚乳酸立构复合体系的结晶行为

设计合成了梳形聚(聚乙二醇甲醚丙烯酸酯)(PPEGA)及其与聚乙二醇(PEG)的嵌段共聚物(PEG-b-PPEGA).通过与高分子量左旋聚乳酸(PLLA)和右旋聚乳酸(PDLA)共混探究了PEG不同的结构对PLA立构复合体系(sc-PLA)结晶的影响.结果 表明线形PEGA和PEG能与sc-PLA完全相容,两者均能促进...     

聚天冬氨酸/3,5-二氨基苯甲酸的合成及缓蚀阻垢性能

通过氨基开环的方法合成了聚天冬氨酸/3,5-二氨基苯甲酸接枝共聚物(PASP/3,5-DMBA),采用静态阻垢、动态腐蚀等方法考察了该共聚物的阻垢和缓蚀性能。结果表明,3,5-二氨基苯甲酸的引入可有效改善聚天冬氨酸(PASP)的阻垢与缓蚀性能,尤其在较低的浓度下对CaSO_4和Ca_3(PO_4)_2的阻垢性能有明显的提高。当PASP/3,5-DMBA药剂用量分别为1.25mg/L、6mg/L时,其对CaCO_3、CaSO_4的阻垢效率接近100%。当用量为18mg/L时,对Ca_3(PO_4)2的阻垢效率可达75%。通过扫描电镜(SEM)观察发现,加入PASP/3,5-DMBA后钙垢晶体结构发生了畸变,呈分散开花状。     

聚丙烯酸/聚丙烯酰胺水溶液复合特性的研究

通过酸度、电导率、粘度、接触角的测定,研究了聚丙烯酸 (PAA) /聚丙烯酰胺 (PAM) 水溶液复合物及复合物膜的结构和性能。结果表明,酸度、温度、浓度和复合比影响PAA/PAM的复合水溶液中大分子链的构象和流体力学体积,适度的氢键作用可以形成均相的复合溶液。经过热处理和未经热处理的聚合物膜表现出了不同的亲水性能。     

苯胺链段为侧基的聚酰胺酸的合成及性质

采用三元共聚法制备了苯胺齐聚物为侧链的接枝型聚酰胺酸. 通过红外光谱、核磁共振谱及高效凝胶渗透色谱等技术对聚合物结构进行了表征. 该材料亚胺化后具有十分优异的热稳定性. 紫外-可见光谱和电化学测试结果表明, 该聚合物具有独特的光谱性质和可逆的电化学活性. 聚酰胺酸/ITO电致变色电极具有颜色变化明显, 响应速度较快, 着色效率高等优点, 是一种综合性能较好的电致变色聚合物材料.     

聚乳酸共混体系的研究进展

聚乳酸是人工合成的可生物降解的热塑性脂肪族聚酯 ,是一种环境友好的材料 ,逐渐成为人们研究的热点。本文根据聚乳酸共混体系中另一组分的生物降解性 ,将聚乳酸共混体系分为完全可生物降解共混体系和部分可生物降解共混体系两类。针对体系的相容性和结晶结构以及在提高PLA的性能和降低成本等方面 .综述了聚乳酸共混体系的最新研究进展 ,并对其发展动态进行了简要介绍     

Synthesis and Characterization of Novel Nanophase Hexagonal Poly(2,5‐dimethoxyaniline)

Novel nanophase hexagonal structured polyaniline (PANI) and poly(2,5‐dimethoxyanilines) (PDMA) were synthesized by oxidative polymerization involving the respective anilines and a mixture of ferric chloride and ammonium persulfate. The morphological, spectral and electrochemical characteristics of the polymers were determined from the results of SEM, FTIR, UV‐vis, TGA and cyclic voltammetry experiments. The hexagonal PANI and PDMA nanorods (15–200 nm diameter) exhibited very good thermal stabilities, losing only 10% of their weight on heating to 400 °C. Electrochemical data indicated a pernigraniline state of the polymers with formal potential, E°′, values of 394±6 mV and 400±1 mV, for PANI (conductance, C=0.37×10^?3 S) and PDMA (conductance, C=2.02×10^?3 S), respectively. The pernigraniline state was confirmed by sharp FTIR pernigraniline quinoidic peaks (PANI: 1414 cm^?1; PDMA: 1157 cm^?1), and UV‐vis absorption maxima at 340–370 nm (PANI) and 450–650 nm (PDMA) which are characteristic of charge transfer excitons of the quinoid structures of pernigraniline.     

Photo-grafting Poly(acrylic acid) onto Poly(lactic acid) Chains in Solution

Poly(lactic acid)(PLA)is one of the most important bio-plastics,and chemical modification of the already-polymerized poly(lactic acid)chains may enable optimization of its material properties and expand its application areas.In this study,we demonstrated that poly(lactic acid)can be readily dissolved in acrylic acid at room temperature,and acrylic acid can be graft-polymerized onto poly(lactic acid)chains in solution with the help of photoinitiator benzophenone under 254 nm ultraviolet(UV)irradiation.Similar photo-grafting polymerization of acrylic acid(PAA)has only been studied before in the surface modification of polymer films.The graft ratio could be controlled by various reaction parameters,including irradiation time,benzophenone content,and monomer/polymer ratios.This photo-grafting reaction resulted in high graft ratio(graft ratio PAA/PLA up to 180%)without formation of homopolymers of acrylic acid.When the PAA/PLA graft ratio was higher than 100%,the resulting PLA-g-PAA polymer was found dispersible in water.The pros and cons of the photo-grafting reaction were also discussed.     

基于聚3,4-乙撑二氧噻吩和1-芘丁酸构建的新型铁卟啉仿生传感器及其对邻苯二酚的催化研究

利用π-π共轭效应,将1-芘丁酸(PBA)与导电高聚物聚3,4-乙撑二氧噻吩(PEDOT)相连,并通过Zr4+与羧基形成的配位键将羟基铁卟啉(Hematin)与PBA相连接,将Hematin固定于电极上,构建出一种制备过程简单的新型传感器(GCE/PEDOT/PBA/Hematin)。为了检验这种仿生传感器的稳定性和灵敏度,通过循环伏安法(CV)、交流阻抗法(EIS)和时间电流曲线法(i-t)等各种技术,将其应用于电化学检测中。CV扫描证实在充分除氧的PBS缓冲液中,GCE/PEDOT/PBA/Hematin出现一对准可逆的氧化还原峰,其电子转移速率常数约为4.8 s!1,说明聚合于电极上的PEDOT膜增加了Hematin的电子转移速率。另外,通过i-t曲线检测邻苯二酚,在邻苯二酚浓度5×10!7~2×10!4mol/L范围内,其与催化电流强度呈线性相关,i=0.018C+0.006(R=0.9998),检测灵敏度为0.258μA(μmol·cm2),检出限为0.33 nmol/L(S/N=3),证明此仿生传感器稳定,简单且灵敏度高。     

Determination of Uric Acid in the Presence of Ascorbic Acid Using Poly(3,4‐ethylenedioxythiophene)‐Modified Electrodes

A poly(3,4‐ethylenedioxythiophene) (PEDOT) modified glassy carbon electrode (GCE) was used to determine uric acid in the presence of ascorbic acid at physiological pH facilitating a peak potential separation of ascorbic acid and uric acid oxidation (ca. 365 mV), which is the largest value reported so far in the literature. Also, an analytical protocol involving differential pulse voltammetry has been developed using a microchip electrode for the determination of uric acid in the concentration range of 1 to 20 μM in presence of excess of ascorbic acid.     

不同催化剂作用下聚乳酸/聚碳酸亚丙酯的酯交换反应

选用辛酸亚锡[Sn(Oct)₂]和钛酸四丁酯(TBT)作为聚乳酸(PLA)/聚碳酸亚丙酯(PPC)的酯交换反应催化剂, 研究了溶液条件下单一催化剂及复合催化剂对PLA/PPC酯交换反应的催化作用. 通过对反应产物的分子结构、 热力学及流变学行为进行分析, 结果发现, 无论在单一催化剂还是复合催化剂作用下, PLA与PPC分子间均发生了酯交换反应, 同时伴随着断链反应. 其中, 当Sn(Oct)₂作为单一催化剂或Sn(Oct)₂/TBT作为复合催化剂时, 样品更倾向发生断链反应而非显著的酯交换反应. 进一步分析纯样品在催化剂Sn(Oct)₂或TBT作用下的反应情况, 结果发现, PPC在反应最初阶段以高分子量的分子链断链为主, 且会发生明显的解拉链降解, 从而导致PLA/PPC在等质量比时酯交换反应程度不高, 这为今后更好地研究PLA/PPC酯交换反应提供了思路.     

Ion-Chromatography Performance of Poly(Aspartic) Acid Bonded Silica with Various Pore Sizes at Different Ionic Strengths and Column Temperatures

A significant effect of pore size on selectivity was observed for anion exchange on polyaspartic acid-coated silica (PolyCAT A). The retention order of halogenide anions, Cl^– <Br^– <I^–, was completely reversed between 30nm and 6nm pore materials. The zwitterionic nature of PolyCAT A made possible the simultaneous separation of anions and cations. With the column temperature, retention of cations is increased whereas retention of anions is decreased. The ionic composition of the eluent had a dramatic effect on separation efficiency with PolyCAT A of 30nm pores. The separation efficiency of ions was optimal in sulfuric acid-based eluents of reasonably high ionic strength.     

Simultaneous Removal of Antibiotics and Heavy Metals with Poly(Aspartic Acid)-Based Fenton Micromotors

The discharge of diverse pollutants has led to a complex water environment and posed a huge health threat to humans and animals. Self-propelled micromotors have recently attracted considerable attention for efficient water remediation due to their strong localized mass transfer effect. However, a single functionalized component is difficult to tackle with multiple contaminants and requires to combine different decontamination effects together. Here, we introduced a multifunctional micromotor to implement the adsorption and degradation roles simultaneously by integrating the poly(aspartic acid) (PASP) adsorbent with a MnO₂-based catalyst. The as-prepared micromotors are well propelled in contaminated waters by MnO₂ catalyzing hydrogen peroxide. In addition, the catalytic ramsdellite MnO₂(R-MnO₂) inner layer is decorated with Fe₂O₃ nanoparticles to improve their catalytic performance, contributing to an excellent degradation ability with 90% tetracycline (TC) removal in 50 minutes by enhanced Fenton-like reactions. Combining the attractive adsorption capability of poly (aspartic acid) (PASP), the composite micromotors offer an efficient removal of heavy metal ions in short time. Moreover, the designed micromotors are able to simultaneously remove antibiotic and heavy metals in mixed contaminants circumstance just in single treatment. This multifunctional micromotor with distinctive decontamination ability exhibits a promising prospective in treating multiple pollutants in the future.     

聚苯胺／含联苯结构聚芳砜导电复合膜的研究

采用溶液共混法得到了聚苯胺／含联苯结构聚芳砜导电复合膜。该复合膜有良好的力学性能和导电性能，对其导电规律进行了探讨。热分析结果表明复合膜有良好的热稳定性，用扫描电镜观察了复合膜的微观形貌，表明ＰＡｎ与ＬＰＥＳ的共混相容性较好。