Preparation and Properties of Alginate/Water‐Soluble Chitin Blend Fibers

Water‐soluble chitin (half‐deacetylated chitin) was prepared from chitosan by N‐acetylation with acetic anhydride. Alginate/water‐soluble chitin blend fibers were prepared by spinning their mixture solution through a viscose‐type spinneret into a coagulating bath containing aqueous CaCl₂ and ethanol. The structure and properties of the blend fibers were studied with the aids of infrared spectra (IR), X‐ray diffraction (XRD) and scanning electron microscopy (SEM). structure analysis indicated good miscibility existed between alginate and water‐soluble chitin, due to the strong interaction from the intermolecular hydrogen bonds and electrostatic interactions. Best values for the dry tensile strength and breaking elongation were obtained when the water‐soluble chitin content was 30 wt%. The wet tensile strength and breaking elongation decreased with the increase of water‐soluble chitin content. The introduction of water‐soluble chitin in the blend fiber can improve the water‐retention properties of the blend fiber compared to pure alginate fiber. The fibers treated with aqueous solution of silver nitrate have good antibacterial activity to Staphylococcus aureus.     

Blend membranes from cellulose/konjac glucomannan cuprammonium solution

The blend membranes were prepared from cellulose/konjac glucomannan (KGM) cuprammonium solution by coagulating with aqueous 10 wt% NaOH solution, 20°C and 40°C water, respectively. Miscibility, pore morphology, structure, water permeability and mechanical properties of the blend membranes were investigated. The complex forms of cellulose/KGM in the mixed solutions, the effect of various coagulants and the percent content of KGM (w_KGM) on the structure and properties of the blend membrane are discussed. SEM and mechanical relaxation analysis indicate that the blend membranes are miscible in the range of 0–30 wt% of w_KGM. When w_KGM was smaller than 20 wt%, the tensil strength of the blend membrane coagulated by alkali aqueous solution was enhanced, corresponding to homogeneous structure and small pore size. However, blend membranes having a larger pore size (366 nm by SEM) and water permeability (560 ml/m² h mmHg) were obtained by coagulating the cellulose/KGM (70:30) cuprammonium solution with 40°C water, where ca. 20% of KGM as pore former were removed from the membrane.     

海藻酸盐/壳聚糖衍生物复合抗菌纤维

通过溶液纺丝法制备海藻酸盐/羧甲基壳聚糖（CMC）共混纤维,并用红外光谱,X射线衍射和扫描电镜对共混纤维进行了表征.结果表明：共混体系中的两种组分之间存在着较强的相互作用,有良好的相容性.当ωCMC=0.30时,共混纤维的干态抗张强度达到最大值,13.8cN/tex.当ωCMC=0.10时,纤维的干态断裂伸长率可达23.1%.纤维的湿态抗张强度和断裂伸长率随着CMC含量的增加而降低.CMC的引入,可显著提高纤维的吸水率.用壳聚糖季铵盐对纤维进行处理,可赋予纤维抗菌性.     

Gamma Radiation‐Induced Crosslinked PVA/Chitosan Blends for Wound Dressing

Crosslinked polyvinyl alcohol (PVA) and chitosan polymer blends have been prepared by using gamma irradiation. Chitosan was used in the blends to prevent microbiological growth, such as bacteria and fungi on the polymer. The physical properties of the blend, such as gelation, water absorption, and mechanical properties were examined to evaluate the possibility of its application for wound dressing. A mixture of PVA/chitosan, with different ratios, were exposed to gamma irradiation doses of 20, 30, 50 KGy, to evaluate the effect of irradiation dose on the physical properties of the blend. It was found that the gel fraction increases with increasing irradiation dose and PVA concentration in the blend. Swelling percent increased as the composition of chitosan increased in the blend. The PVA/chitosan blend has a water content in the range between 40% and 60% and water absorption between 60% and 100%. The water vapor transmission rate value (WVRT) of the PVA/chitosan blend varies between 50% and 70%. The examination of the microbe penetration shows that the prepared blend can be considered as a good barrier against microbes. Thus, the PVA/chitosan blend showed satisfactory properties for use as a wound dressing.     

Improving polyethylene–octene elastomer/chitosan by graftation of acrylic acid onto polyethylene–octene elastomer—mechanical properties and biodegradability examination and composites characterization

In this study, the properties of polyethylene–octene elastomer/chitosan (POE/chitosan) and acrylic acid (AA)‐grafted‐polyethylene–octene elastomer/chitosan (POE‐g‐AA/chitosan) were examined using various characterizing instruments. Mechanical and thermal properties of POE deteriorated noticeably when it was blended with chitosan, due to the unsatisfactory compatibility between the two phases. The greater compatibility of POE‐g‐AA with chitosan, due to the formation of ester carbonyl and imide groups, led to a much better dispersion and homogeneity of chitosan in the POE‐g‐AA matrix and consequently to noticeably better mechanical properties. Furthermore, with a lower melting point temperature, the POE‐g‐AA/chitosan blend was more easily processed than POE/chitosan. POE‐g‐AA/chitosan had a higher water resistance than POE/chitosan. Both blends suffered weight loss when buried in soil, especially at high levels of chitosan substitution, indicating that both were biodegradable. The mechanical properties of both blends, such as tensile strength and elongation at break, also deteriorated after being buried in soil. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3882–3891, 2003     

Preparation and characterization of cellulose and konjac glucomannan blend film from ionic liquid

Blend films from cellulose and konjac glucomannan (KGM) in room temperature ionic liquid 1‐allyl‐3‐methylimidazolium chloride were satisfactorily prepared by coagulating with water. The composition of the blend films was gravimetrically analyzed, and the compatibility of the two natural polymers was characterized by Fourier transform infrared spectroscopy and wide‐angle X‐ray diffraction. The results indicate good compatibility and strong interactions between cellulose and KGM, resulting in almost no loss of the water‐soluble KGM from the blend films even after the water coagulating and washing. However, microstructure analyses portrayed phase separations in the blend films, namely, egg‐like new phase particles were embedded in a continuous matrix base (MB). Phase diagram analysis and differential scanning calorimetry of the phase inversion coagulation process suggest that relative low molecular mass part of both cellulose and KGM formed the continuous MB, whereas the egg‐like new phase particles were super patterns of relative high molecular mass of both polymers, which played an important role in strengthening the blend material. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1686–1694, 2009     

Fiber‐forming blend polypropylene‐polyvinyl alcohol

The preparation of a fiber‐forming blend consisting of polypropylene and polyvinyl alcohol mixed with glycerol and with polypropylene grafted with maleic anhydride were studied. The physical and mechanical properties of blend fibers were also studied. The rheological measurements for semiquantitative evaluation of technological compatibility of the components and for processing the polymeric material in extruding and spinning process were carried out. The experimental results revealed the technological compatibility of the polypropylene‐polyvinyl alcohol blend in the presence of glycerol and polypropylene grafted with maleic anhydride. The colloidal structure of interface layer is assumed to be in a three‐ or four‐component system. The mixture of polyvinyl alcohol with glycerol allows for the preparation of well spun fiber‐forming polypropylene blends. Polypropylene‐polyvinyl alcohol blend fibers consisting of up to 20% polyvinyl alcohol with sufficient mechanical properties, higher porosity and significantly higher sorption of water than polypropylene fibers alone were prepared. Copyright © 2001 John Wiley & Sons, Ltd.     

Baked hydrogel from corn starch and chitosan blends cross‐linked by citric acid: Preparation and properties

Citric acid (CA)–modified hydrogels from corn starch and chitosan were synthesized using a semidry condition. This strategy has great benefits of friendly environment because of the absence of organic solvents and compatible with the industrial process. The hydrogel blends were prepared with starch/chitosan ratios of 75/25, 50/50, and 25/75. The thermal stability, morphology, water absorption, weight loss in water, and methylene blue absorption were determined. Multi‐carboxyl structure of CA could result in a chemical cross‐linking reaction between starch, chitosan, and CA. The cross‐linking reaction between free hydroxyl groups of starch, amino groups of chitosan, and carboxyl groups of CA has been confirmed by attenuated total reflectance infrared (ATR‐IR) spectroscopy, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) analysis. The water absorption properties of CA‐modified hydrogel blends were increased significantly compared with the native starch and chitosan. Moreover, the hydrogel blends modified with CA showed good water resistance and gel content. The morphology study confirmed the complete chemical cross‐linking and porous structure of hydrogel blends. The hydrogel blend with the starch/chitosan ratio of 50/50 presented powerful absorption of methylene blue as well as chemical cross‐linking reaction and dense structure. In sum, the hydrogel blend comprising 50% starch and 50% chitosan has the potential to be applied for water maintaining at large areas, for example, in agriculture.     

Thermal properties and structure of electrospun blends of PVDF with a fluorinated copolymer

We report the structure and thermal properties of blends comprising poly(vinylidene fluoride) (PVDF) and a random fluorinated copolymer (FCP) of poly(methyl methacrylate)‐random‐1H,1H,2H,2H‐perfluorodecyl methacrylate, promising membrane materials for oil–water separation. The roles of processing method and copolymer content on structure and properties were studied for fibrous membranes and films with varying compositions. Bead‐free, nonwoven fibrous membranes were obtained by electrospinning. Fiber diameters ranged from 0.4 to 1.9 μm, and thinner fibers were obtained for PVDF content >80%. As copolymer content increased, degree of crystallinity and onset of degradation for each blend decreased. Processing conditions have a greater impact on the crystallographic phase of PVDF than copolymer content. Fibers have polar beta phase; solution‐cast films contain gamma and beta phase; and melt crystallized films form alpha phase. Kwei's model was used to model the glass transition temperatures of the blends. Addition of FCP increases hydrophobicity of the electrospun membranes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 312–322     

Preparation and properties of water‐soluble chitosan and polyvinyl alcohol blend films as potential bone tissue engineering matrix

The blend film was prepared by casting solutions of water‐soluble hydroxyethyacryl‐chitosan (HEA‐CS) and polyvinyl alcohol (PVA) and cross‐linked by glutaraldehyde. The structure and properties of the blend films were estimated by wide‐angle X‐ray diffraction (WXRD), contact angle measurements with water, and scanning electron microscopy (SEM). The tensile properties of the blend films were investigated and the tensile strength (TS) and the elongation increased with the increased amount of PVA. The thermal stability (thermogravimetric (TG) and derivative thermogravimetric (DTG)) was evaluated and HEA‐CS was more thermally‐stable than that of PVA. The water swelling properties analysis indicated that HEA‐CS in the blends promoted the water absorption owing to its porous structure and the antimicrobial ability of the blend films was retained. Indirect cytotoxicity assessment of the blend films with human bone sarcoma cell (SW1353) indicated that the biomaterials were non‐toxic and did not release substances harmful to living cells. Copyright © 2009 John Wiley & Sons, Ltd.     

Chitosan/N-methylol nylon 6 blend membranes for the pervaporation separation of ethanol–water mixtures

Blend membranes of chitosan and N-methylol nylon 6 were prepared by solution blending. Their pervaporation performances for the separation of ethanol–water mixtures were investigated in terms of acid (H₂SO₄) post-treatment, feed concentration, blend ratio and temperature. The pervaporation performance of the blend membranes was significantly improved by ionizing with H₂SO₄. The blend ratio of chitosan and N-methylol nylon 6 plays a different role at feed solutions of low and high water content. At a feed solution having low water content, an increase in chitosan content caused a decrease in permeability and an increase in separation factor. At a feed solution having high water content, the permeability increases with an increase in chitosan content, while the separation factor shows a maximum value around 60 wt% chitosan. It is proposed that extra permeation channels generated from the phase separation boundary between ionized chitosan and N-methylol nylon 6 account for the abnormal temperature dependence of pervaporation performance of the blend membranes.     

A Preliminary Study on Preparation of the Aromatic/Aliphatic Co‐polyurea as Spun Fibers

Aromatic‐aliphatic co‐polyurea has been synthesized from 4,4 prime‐diphenylmethane diisocyanate (MDI), m‐phenylene diamine (m‐PDA), and 1,6‐diaminohexane (HDA) in DMAc by solution polymerization. The chemical structure of the co‐polyurea has been characterized by ¹H‐NMR. The thermal properties of the copolymers were measured by DSC and TGA. The co‐polyurea solutions were spun into fibers by means of wet spinning. The effects of coagulation conditions on the morphologies and mechanical properties of the co‐polyurea as spun fibers are discussed.     

Morphology of polysaccharide blend fibers shaped from NaOH, <Emphasis Type="Italic">N</Emphasis>-methylmorpholine-<Emphasis Type="Italic">N</Emphasis>-oxide and 1-ethyl-3-methylimidazolium acetate

The aim of this study was to find newly structured biopolymer blends bearing those adjustable features able to produce innovative materials. Apart from cellulose derivatives (cellulose carbamate and carboxymethyl cellulose), mannans (guar gum, locust bean gum, and tragacanth gum), xylan, starch (cationized), ι-carrageenan, and xanthan were chosen as blend polysaccharides for cellulose as matrix. In order to study their integration into the cellulose skeleton, fibers were shaped from three different solvents: NaOH by a special wet-spinning process, as well as N-methylmorpholine-N-oxide (NMMO) and 1-ethyl-3-methylimidazolium acetate (EMIMac) via Lyocell technology. The structure and morphologies of the fibers were analyzed by X-ray wide-angle scattering and atomic force microscopy. Hydrophilic/hydrophobic properties were determined by means of a contact angle, as well as moisture content and water retention values, while the surface properties throughout zeta-potential measurements. Being very different processes, the wet spinning in NaOH solution and the dry–wet spinning are deeply impacted by the types of solvent and polysaccharide. The X-ray results for NMMO fibers revealed the highest orientation compared with EMIMac having the lowest orientation of NaOH fibrous types. AFM images also show the lowest surface roughnesses for NMMO and EMIMac fibers. The moisture content and water retention values support these trends, while the water contact angle results show insignificant differences between the samples from EMIMac and NaOH, even though the values calculated for NMMO fibers were the lowest.     

Biodegradable stereocomplex materials of polylactide‐grafted dextran exhibiting soft and tough properties in dry and wet states

Water‐swellable biodegradable materials exhibiting mechanically tenacious and tough characters in the wet state were prepared by a simple blend of two enantiomeric polylactide‐grafted dextran copolymers (Dex‐g‐PLLA and Dex‐g‐PDLA). DSC and WAXD analyses demonstrated the formation of SC crystals in the copolymer blend films. SC blend films showed lamellar‐type microphase‐separated structures. When swollen with water, these blend films showed the same level of tensile strengths and Young's modulus as the films in the dry state. SC blend films degraded gradually over a month under physiological conditions with a degradation rate faster than the corresponding Dex‐g‐PLLA films. The SC‐forming enantiomeric mixture of polylactide‐grafted polysaccharides should be a good candidate for an implantable biocompatible material exhibiting favorable mechanical properties and degradation behavior. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

CHARACTERIZATION OF POLY(VINYL ALCOHOL)-KONJAC GLUCOMANNAN BLEND FILMS

This article deals with the characterization of blend films obtained by mixing poly(vinyl alcohol) (PVA) and konjac glucomannan (KGM) in aqueous solution. The DTA curves of PVA/KGM blend films showed overlapping of the main thermal transitions characteristic of the individual polymers. The exothermic peak at 312°C, which resulted from the thermal degradation of the KGM, shifted slightly to a higher temperature at low PVA content (≤20 wt%). The weight-retention properties of the blend films indicated that thermal stability of the blend films were better than pure KGM film at PVA content below 20 wt%. The crystallinities, tensile strength, and elongation at break of the films increased with the PVA content, and reached the maximum values at 20 wt% PVA, then decreased. Changes in the carbonyl stretching band of KGM and hydroxyl stretching regions of KGM and PVA were detected by FTIR analysis. Those are attributable to the existence of a certain degree of inteaction between KGM and PVA, and resulted from intermolecular hydrogen bonds. Phase separation phenomena were observed by examining the surface of the blend films by SEM.     

Preparation and properties of ionically cross‐linked chitosan nanoparticles

Chitosan nanoparticles were fabricated by a method of tripolyphosphate (TPP) cross‐linking. The influence of fabrication conditions on the physical properties and drug loading and release properties was investigated by transmission electron microscopy (TEM), dynamic light scattering (DLS), and UV–vis spectroscopy. The nanoparticles could be prepared only within a zone of appropriate chitosan and TPP concentrations. The particle size and surface zeta potential can be manipulated by variation of the fabrication conditions such as chitosan/TPP ratio and concentration, solution pH and salt addition. TEM observation revealed a core–shell structure for the as‐prepared nanoparticles, but a filled structure for the ciprofloxacin (CH) loaded particles. Results show that the chitosan nanoparticles were rather stable and no cytotoxicity of the chitosan nanoparticles was found in an in vitro cell culture experiment. Loading and release of CH can be modulated by the environmental factors such as solution pH and medium quality. Copyright © 2008 John Wiley & Sons, Ltd.     

Spectroscopic studies of the conformational properties of naphthoyl chitosan in dilute solutions

A naphthoyl chitosan derivative was prepared, and its conformations in dilute solutions were characterized with spectroscopic methods, including circular dichroism (CD) spectroscopy and fluorescence emission spectroscopy. The CD spectrum of this polymer showed a negative band at about 295 nm in dimethyl sulfoxide (DMSO), indicating that the polymer adopted a helical secondary structure. A helix reversion occurred at concentrations greater than 1 mg/mL. The intensity of the CD signal decreased with the addition of water to the solution, and this suggested a change from a helical conformation to a looser one as a result of the collapse of intramolecular hydrogen bonds. In the fluorescence emission experiments, two kinds of excimer emission bands were detected at 375 and 425 nm, and they were assigned to a partially overlapped dimer with a twisted geometry and a fully overlapped dimer with a sandwichlike geometry, respectively. Adding water to a solution of naphthoyl chitosan in DMSO resulted in a gradual reduction of the emission intensity at 375 nm, and this implied that the twisted arrangement of the chromophore was destroyed by the presence of water. The relative intensity (i.e., the ratio of the intensity of the excimer emission at 425 nm to that of the excimer emission at 375 nm) depended on the solvent (DMSO, N,N‐dimethylformamide, N,N‐dimethylacetamide, and 1‐methyl‐2‐pyrrolidinone), and this indicated that the conformation of naphthoyl chitosan was solvent‐dependent. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2747–2758, 2004     

Synthesis of chitosan‐based thermo‐ and pH‐responsive porous nanoparticles by temperature‐dependent self‐assembly method and their application in drug release

In this research, thermo‐ and pH‐responsive chitosan‐based porous nanoparticles were prepared by the temperature‐dependent self assembly method. The chitosan‐graft‐poly(N‐isopropylacrylamide) (CS‐g‐PNIPAAm) copolymer solution was prepared through polymerization of N‐isopropylacrylamide (NIPAAm) monomer in the presence of chitosan (CS) solution using cerium ammounium nitrate as the initiator. Then, CS‐g‐PNIPAAm solution was diluted by deionized water and heated to 40 °C for CS‐g‐PNIPAAm self‐assembly. After that, CS‐g‐PNIPAAm assembled to form micelles in which shell layer was CS. Crosslinking agent was used to reinforce the micelle structure to form nanoparticle. The molar ratio of CS/NIPAAm in the feed mixture was changed to investigate its effect on structure, morphology, thermal‐ and pH‐responsive properties of the nanoparticles. TEM images showed that a porous structure of nanoparticles was developed. The synthesized nanoparticles carried positive charges on the surface and exhibited stimuli‐responsive properties, and their mean diameter thus could be manipulated by changing pH value and temperature of the environment. The nanoparticles showed a continuous release of the encapsulated doxycycline hyclate up to 10 days during an in‐vitro release experiment. These porous particles with environmentally sensitive properties are expected to be utilized in hydrophilic drug delivery system. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5126–5136, 2009     

Graft Copolymerization of (Dimethylamino)Ethyl Methacrylate onto Chitosan Initiated by Ceric Ammonium Nitrate

Abstract

(Dimethylamino)ethyl methacrylate (DMAEMA) was grafted onto chitosan using ceric ammonium nitrate as initiator in acetic acid solution. The effects of reaction variables on the grafting percentage and efficiency percentage were investigated, including the amounts of monomer and initiator, reaction time and reaction temperature. The grafted copolymers were confirmed by FTIR, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results of TGA and DSC indicated the improvement of thermal stability for chitosan‐g‐poly(PDMAEMA). Solubility test revealed the improved hydrophilicity of grafted chitosan in aqueous acetic acid solution, and its swelled behavior in mixtures of glacial acetic acid and anhydrous ethanol (the ratios of 1:1 and 1:2, v/v). The grafted copolymer possessed amphiphilic structure and exhibited properties of polymeric surfactant.     

Application of Polyvinyl Alcohol (PVA)/Carboxymethyl Cellulose (CMC) Hydrogel Produced by Conventional Crosslinking or by Freezing and Thawing

Hydrogels for this study were prepared from a mixture of PVA and CMC using three different techniques, i.e., freezing and thawing, electron‐beam irradiation or combined freezing and thawing and electron beam irradiation. A comparative study between the three techniques was carried out in terms of gel fraction (%) and swelling (%). It was found that the physical properties of the hydrogel were improved when the combination of freezing and thawing and irradiation were used rather than just freezing and thawing, or irradiation only. The effects of temperature and soil fertilizers on swelling (%) were examined to evaluate the usefulness of the hydrogel as a super absorbent in the soil. It was found that the swelling ratio increased as the composition of CMC increased in the blend. Hence, the blend having the composition 80/20 (CMC/PVA) was used as a super absorbent in the soil for agriculture. Moreover, the water retention increased in the soil containing this hydrogel. Thus, this type of hydrogel can be used to increase water retention in desert regions.